I BODY
B
SECTION
SEAT C
E
CONTENTS
PRECAUTIONS .......................................................... 2 INSTALLATION ..................................................... 6 F
Service Notice .......................................................... 2 Disassembly and Assembly ...................................... 6
Precautions for Supplemental Restraint System SEAT BACK ........................................................... 6
(SRS) AIR BAG and SEAT BELT PRE-TEN- SEAT CUSHION .................................................... 7 G
SIONER .................................................................. 2 REAR SEAT ................................................................ 8
Precautions for Work ................................................ 2 Component Parts Drawing ....................................... 8
Trouble Diagnosis Precaution .................................. 2 Removal and Installation ........................................ 13
H
FRONT SEAT .............................................................. 4 REMOVAL ........................................................... 13
Component Parts Drawing ....................................... 4 INSTALLATION ................................................... 13
Removal and Installation .......................................... 6 Disassembly and Assembly .................................... 13
REMOVAL ............................................................. 6 SECOND 3-PASSENGER + THIRD 2-PAS- SE
SENGER ............................................................. 13
AUXILIARY SEAT ................................................ 13
J
SE-1
PRECAUTIONS
PRECAUTIONS PFP:00001
When removing or installing various parts, place a cloth or padding onto the vehicle body to prevent
scratches.
Handle trim, molding, instruments, grille, etc. carefully during removing or installing. Be careful not to oil or
damage them.
Apply sealing compound where necessary when installing parts.
When applying sealing compound, be careful that the sealing compound does not protrude from parts.
When replacing any metal parts (for example body outer panel, members, etc.), be sure to take rust pre-
vention measures.
Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT
BELT PRE-TENSIONER EIS001JJ
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow harness connectors.
Precautions for Work EIS001JK
When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the compo-
nent with a shop cloth or vinyl tape to protect it.
Protect the removed parts with a shop cloth and keep them.
Replace a deformed or damaged clip.
If a part is specified as a non-reusable part, always replace it with new one.
Be sure to tighten bolts and nuts securely to the specified torque.
After re-installation is completed, be sure to check that each part works normally.
Follow the steps below to clean components.
Water soluble foul: Dip a soft cloth into lukewarm water, and wring the water out of the cloth to wipe the
fouled area.
Then rub with a soft and dry cloth.
Oily foul: Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%), and wipe
the fouled area.
Then dip a cloth into fresh water, and wring the water out of the cloth to wipe the detergent off. Then rub
with a soft and dry cloth.
Do not use organic solvent such as thinner, benzene, alcohol, and gasoline.
For genuine leather seats, use a genuine leather seat cleaner.
Trouble Diagnosis Precaution EIS001JL
When carrying out the IVMS control unit input/output signal inspection, be sure to connect the checking
adapter III(special service tool) to prevent incorrect diagnosis.
With the battery connected, if each local control unit (LCU) connector is left disconnected for at least 1
minute, the IVMS control unit stores a communication inactive failure. After reconnecting the connector,
SE-2
PRECAUTIONS
any of the following steps shall be done. "Disconnect the IVMS control unit BAT power supply" or "using
CONSULT-II, execute Erase memory". A
SE
SE-3
FRONT SEAT
SIIA1048E
1 Seat cushion outer finisher 2 Reclining device 3 Reclining device inner finisher
4 Reclining lever knob 5 seat back frame 6 Seat back trim & pad
7 Seat back cover 8 Seat cushion trim & pad 9 Seat cushion frame
10 Inner leg cover 11 Outer leg cover 12 Slide rail outer
13 Slide rail inner 14 Seat cushion inner finisher
SE-4
FRONT SEAT
SIIA1049E SE
1 Seat back bracket 2 Seat back trim & pad (center) 3 Seat back frame (center)
4 Multi seat back console 5 Seat back frame 6 Seat back trim & pad
7 Seat cushion trim & pad 8 Hook 9 Reclining device inner finisher J
10 Reclining device 11 Reclining lever knob 12 Reclining device outer finisher
13 Cover
K
Center seat (LHD models)
SIIA1075E
1 Seat cushion trim & pad 2 Seat back bracket 3 Seat back pad & frame
4 Seat back frame 5 Multi seat back console
SE-5
FRONT SEAT
NOTE:
When removing and installing seats, use shop clothes to protect the parts from damage.
REMOVAL
Separate seat
1. Remove outer leg cover and inner leg cover.
2. Remove mounting bolts, and remove seats from vehicle.
SIIA1029E
SIIA1034E
SIIA1035E
SEAT BACK
Separate seat
1. Remove hog rings at the bottom of seat back, and partially pull off the trim.
SE-6
FRONT SEAT
PIIA0528E
D
3. Remove hog rings from seat back frame, and remove trim.
4. Remove pad from seat back frame.
E
Center seat (LHD models)
1. Remove seat back bracket (T50-type torx bolt: 2).
2. Remove seat back console (screw: 4). F
3. Remove trim and pad from seat back frame.
SEAT CUSHION
Separate seat G
1. Remove reclining device finisher (outer and inner).
2. Remove hog rings on the back side of seat cushion, and remove seat cushion trim and pad.
H
3. Separate trim from pad.
Bench seat and center seat
Remove hog rings, and separate the trim from pad. SE
SE-7
REAR SEAT
SIIA1044E
SE-8
REAR SEAT
SIIA1045E SE
1 Seat cushion bracket 2 Seat sliding rail (RH) 3 Release wire
4 Seat sliding rail (LH) 5 Seat cushion bracket (RH) 6 Seat cushion trim & pad
7 Seat cushion inner frame 8 Seat back trim & pad 9 Seat back frame J
10 Stopper 11 Seat cushion bracket (LH)
SE-9
REAR SEAT
SIIA1050E
1 Seat cushion trim & pad 2 Leg bracket (RH) 3 Seat cushion frame
4 Leg cover 5 Leg bracket (LH) 6 Seat cushion stopper (RH)
7 Seat cushion stopper (LH) 8 Seat back bracket (RH) 9 Seat back trim & pad
10 Seat back frame 11 Seat back stopper (RH) 12 Seat back board
13 Seat back stopper (LH) 14 Strap 15 Seat back bracket (LH)
16 Seat cushion frame rubber 17 Leg carpet
SE-10
REAR SEAT
SIIA1043E SE
1 Seat cushion bracket (RH) 2 Seat cushion trim & pad 3 Seat cushion frame
4 Seat cushion frame rubber 5 Seat cushion bracket (LH) 6 Seat cushion stopper
7 Seat back trim & pad 8 Seat back frame 9 Seat back stopper J
SE-11
REAR SEAT
SIIA1073E
Auxiliary seat
SIIA1074E
SE-12
REAR SEAT
A
NOTE:
During removal or installation, protect a part or location with a cloth or padding where it may interfere with oth-
ers.
B
REMOVAL
1. Remove bolt cap.
2. Remove mounting bolt, and remove seat. C
INSTALLATION
Install in the reverse order of removal.
D
Disassembly and Assembly EIS0019X
SIIA1046E
H
AUXILIARY SEAT
1. Remove seat cushion finisher.
2. Pull off cotter pins from shaft connecting seat cushion and SE
bracket.
3. Pull off shaft.
J
SIIA1047E L
SE-13
REAR SEAT
SE-14