AL-023/AL-024/
OC-003/OC-004
PROJECT: PROJECT No.:
5E-886-006
ORDER SPECIFICATION FOR REVISION: SHEET No.:
SPECIAL ELECTRIC CABLES
0 1/7
TOTAL
5E-886-006 O.S. SPECIAL ELECTRIC CABLES SHEET 2 / 7
REVISION 0
DATE 07/01/2016
EXECUTED P. Murilo
CHECKED P. Murilo
APPROVED Alexandre
SUMMARY
1- GENERAL
2- GUARANTEE
4- TECHNICAL SPECIFICATION
7- CERTIFICATIONS
The Manufacturer shall present an offer covering all the requirements of this Order Specification,
where else applicable.
2- GUARANTEE
The Contractor shall guarantee the Equipment at least until the date designated below, whichever
comes first:
Any defect and/or failures discovered within the Guarantee period, whose causes shall be
attributed to the Contractors responsibility, shall be immediately repaired or replaced by the
Contractor at the Contractors expenses.
The repaired or replaced parts shall be guaranteed additionally for 12 (twelve) months after the
repairs or the replacements have been carried out.
The above mentioned items have to be designed and manufactured according to the following
standards and rules (where applicable):
4- TECHNICAL SPECIFICATION
Standards:
- IEC 60092-350; IEC 60092-353;
- Halogen free properties: IEC 60754-1-2;
- Low Smoke emission: IEC 6134-1/2;
Remarks:
All cables shall be DNV certificated and supplied with certificate.
All cables shall be manufactured with the following text printed throughout entire cable
length: OCEANA ESTALEIRO
Scope of Supply:
For Ethernet with twisted pair it is recommended to use a S/FTP (individual twisted pair foils and
overall braid) cable of category 7.
Cable Data:
Type: ISO/IEC11801 Class F S/FTP CAT7, twisted pair, shielded, 4x2x0.5 mm
Impedance: 100 ohm
Range: Max 90 m
Recommended cable:
Manufacture : Nexans
Description : LANmark-7 Maritime CAT7 S/FTP
23 AWG LSFROH SHF1 Grey
Conductor : 4 pairs AWG23 (0.58q)
Cable outer diam. : 7.9 mm
Impedance : 100
Approved by : DNV certificate E-8001
Part No. manufacture : N10m.002
Maximum cable length : Max 90m
Quantity: 8.000 meters
The fiber optical cables must be of multimode type with a core diameter of 50 m, and cladding diameter
125m. ST connectors (also known as BFOC) are to be used in both ends of the cable.
Cable Data:
Type : Multimode Cable
Core Diameter : 50 m
Cladding Diameter : 125 m
Recommended cable:
AL-023/AL-024/OC-003/OC-004 | 5E-886-006_0 O.S. Special Electrical Cables Sheet 5/7
Leoni: AT-V(ZN)H(ZN)H N of cores:6 Conductor cross section G50/125
Quantity: 300 meters
For the CAN bus, it is recommend using a shielded twisted pair cable. According to the ISO 11898-2
standard, cables to be chosen for CAN bus lines should have a nominal impedance of 120 Ohm, and a
specific line delay of nominal 5 ns/m. Line termination has to be provided through termination resistors of
120 Ohm located at both ends of the line. The length related resistance should have 70 mohm/m.
Cable Data:
Type: Twisted pair, shielded, low capacitance, 0.75 mm.
Cable outer diam.: max 14 mm (when connector is used).
Impedance: 120 (min. 108 , max. 132 )
Capacitance: max. 60 pF/m.
Resistance: max 40 /km.
Range: Max 300m.
Recommended cable:
Manufacture: UI Lapp Germany
Description: Unitronic BUS CAN UL/CSA
Conductor: 2x2x0,75q
Impedance: 120
Max. cable length: 300m
Approved by: UL/ULC
Part no. Manufacture: 2170 270 2x2x0,75
Supplier worldwide: Miltronic AS Norway
Quantity: 4.000 meters
4.4.1 Low loss coaxial cable RG-214- 50 Ohm, with conductor stranded cooper, LSFH.
or equivalent HUBER+SUHNER G_07262_D
Quantity: 800 meters
4.4.2 Low loss coaxial cable RG-11- 75 Ohm, with conductor stranded cooper, LSFH.
Quantity: 200 meters
4.4.3 Low loss coaxial cable RG-06- 75 Ohm, with conductor stranded cooper, LSFH.
Quantity: 500 meters
All necessary drawings and technical information for the correct application and installation of the
equipment .
Quality assurance certificates.
DNV certificates.
Manufacturer certificates and Guarantee certificate shall be also provided for each one equipment
when applicable.
All necessary inspections and tests shall be carried out during manufacturing process according to
manufacturers standards and Classifications Society requirements.
7- CERTIFICATIONS