This chapter describes how to connect Integrated Services Digital Network (ISDN) Primary Rate
Interface (PRI) network modules for Cisco modular routers and contains the following sections:
Channelized T1/E1 PRI Network Modules with G.703, page 7-2
Channelized T1/ISDN PRI Network Modules, page 7-5
Channelized T1/ISDN PRI with CSU Network Modules, page 7-6
Channelized E1/ISDN PRI Balanced (120-ohm) Network Modules, page 7-8
Channelized E1/ISDN PRI Unbalanced (75-ohm) Network Modules, page 7-10
PRI Module LEDs, page 7-12
Online Insertion and Removal with a Cisco PRI Network Module (Cisco 3660 and Cisco 3745
Only), page 7-16
Upgrading ISDN PRI Network Modules, page 7-16
Related Documents, page 7-17
Unless specifically identified, references to PRI modules in this chapter include all these network
modules.
Note Cisco Fast Ethernet-PRI network modules also provide a PRI interface. See Chapter 4, Connecting
Fast Ethernet-PRI Network Modules, for further information.
Note Do not install an ISDN BRI network module in the same chassis as an ISDN PRI network module,
unless you are using Cisco IOS Release 11.3(3)T or later release. Earlier Cisco IOS releases do not
support this configuration.
CT1/PRI modules are available with or without a built-in channel service unit (CSU), and with one or
two ports. CT1/PRI modules connect to an external CSU; CT1/PRI-CSU modules connect directly to the
network. Each T1 module provides up to 24 virtual channels per T1 port. Each channel can be configured
individually as a serial interface.
CT1/PRI and CT1/PRI-CSU modules receive and transmit data bidirectionally, at the T1 rate of
1.544 Mbps.
Table 7-1 Modular Access Routers Supporting Cisco Channelized T1/E1 PRI Network Modules with
G.703
Figure 7-1 and Figure 7-2 show the faceplates for the 1-port and 2-port channelized T1/E1 PRI network
modules with G.703.
Figure 7-1 1-Port Channelized T1/E1 PRI Network Module with G.703
NM-1CE1T1-PRI
RX TX CD LP
MON MON
T1
RA AIM
E1-BAL
C0 LA E1-UNBAL EN
82886
CTLR 0
Figure 7-2 2-Port Channelized T1/E1 PRI Network Module with G.703
NM-2CE1T1-PRI
CD LP RX TX CD LP
MON MON
T1 T1
RA C1 RA AIM
E1-BAL E1-BAL
LA E1-UNBAL C0 LA E1-UNBAL EN
82887
CTLR 1 CTLR 0
Figure 7-3 Wetting Current Jumper Locations on Channelized T1/E1 PRI Network Modules with G.703
J8/J9
1
2
3
Wetting current
Wetting current jumper
enabled
J8/J9
1
2
3
Wetting current
disabled NM
-2C
E1
T1
-PR
I
3
2
1
CD
J9
RA
LP
LA
T1
CT RX
LR E1
1 -B MO
3
E1 N
2
-U
NB
1
88539
TX
MO
N
J8
C1
C0
CD
RA
LP
LA
T1
CT
LR E1
0 -B
E1
-U
NB
AIM
EN
Warning For connections outside the building where the equipment is installed, the following ports must be
connected through an approved network termination unit with integral circuit protection:
T1
Figure 7-4 shows a connection between a channelized T1/E1 PRI network module with G.703 and a
networking device.
Figure 7-4 Connecting a Channelized T1/E1 PRI Network Module with G.703 to a Networking Device
NM-1CE1T1-PRI
RX TX CD LP
MON MON
T1
88639
RA AIM
E1-BAL
C0 LA E1-UNBAL EN
CTLR 0
cT1
PRI
LOOPBACK
CARRIER
REMOTE
DETECT
ALARM
ALARM
LOCAL
EN
H7460
CTRLR 0
CARRIER
cT1
REMOTE
DETECT
ALARM
ALARM
LOCAL
PRI
EN
CTRLR 1
LOOPBACK
CARRIER
REMOTE
DETECT
ALARM
ALARM
LOCAL
EN
H7461
CTRLR 0
FEPRI
1FE-1CT1
10/100BaseT
CARRIER
REMOTE
CTRLR 0
DETECT
ALARM
ALARM
LOCAL
100Mbps
BACK
LOOP
COLL
LINK
FDX
EN
H7468
T1 serial
cable
T1 CSU
Figure 7-8 1-Port Channelized T1/ISDN PRI with CSU Network Module
cT1
CSU
RX TX RX
OUT IN MON
LOOPBACK
CARRIER
REMOTE
DETECT
ALARM
ALARM
LOCAL
EN
H7465
CTRLR 0
Figure 7-9 2-Port Channelized T1/ISDN PRI with CSU Network Module
LOOPBACK
cT1
CARRIER
REMOTE
DETECT
ALARM
ALARM
LOCAL
CSU
CTRLR 1
RX TX RX
OUT IN MON
LOOPBACK
CARRIER
REMOTE
DETECT
ALARM
ALARM
LOCAL
EN
H7464
CTRLR 0
FEPRI
1FE-1CT1-CSU
10/100BaseT
CARRIER
REMOTE
DETECT
ALARM
ALARM
LOCAL
CTRLR 0
100Mbps
BACK
LOOP
COLL
LINK
FDX
EN
CT1/PRI CSU
port (RJ-48C)
H7469
RJ-48C jack
cE1-B
PRI
LOOPBACK
CARRIER
REMOTE
DETECT
ALARM
ALARM
LOCAL
EN
H7260
CTRLR 0
CE1/PRI-B port
CARRIER
cE1-B
REMOTE
DETECT
ALARM
ALARM
LOCAL
PRI
CTRLR 1
LOOPBACK
CARRIER
REMOTE
DETECT
ALARM
ALARM
LOCAL
EN
H7261
CTRLR 0
CE1/PRI-B ports
CE1/PRI modules are available with one or two E1 ports and with balanced or unbalanced interfaces.
These modules receive and transmit data bidirectionally at the E1 rate of 2.048 Mbps, and provide up to
30 virtual channels per E1 port. Each channel can be configured individually as a serial interface.
FE-PRI
1FE-1CE1-B/U
10/100BaseT
CARRIER
CTRLR 0
REMOTE
DETECT
ALARM
ALARM
LOCAL
100Mbps
BACK
LOOP
COLL
LINK
FDX
EN
CE1/PRI-B (DB-15)
balanced connections
with a DB-15 connector
at the network end
E1 CSU
DB-15 connector
FE-PRI
1FE-1CE1-B/U
10/100BaseT
CARRIER
CTRLR 0
REMOTE
DETECT
ALARM
ALARM
100Mbps
LOCAL
BACK
LOOP
COLL
LINK
FDX
EN
H7473
E1 cable for 75-ohm
balanced connections
with twinax connectors
at the network end
E1 CSU
Twinax connectors
FE-PRI
1FE-1CE1-B/U
10/100BaseT
CARRIER
CTRLR 0
REMOTE
DETECT
ALARM
ALARM
100Mbps
LOCAL
BACK
LOOP
COLL
LINK
FDX
EN
balanced connections
with an RJ-45 connector
at the network end
RJ-45 jack
cE1-U
PRI
LOOPBACK
CARRIER
REMOTE
DETECT
ALARM
ALARM
LOCAL
EN
H8499
CTRLR 0
CE1/PRI-U port
CARRIER
cE1-U
REMOTE
DETECT
ALARM
ALARM
LOCAL
PRI
CTRLR 1
LOOPBACK
CARRIER
REMOTE
DETECT
ALARM
ALARM
LOCAL
EN
H8500
CTRLR 0
CE1/PRI-U ports
FE-PRI
1FE-1CE1-B/U
10/100BaseT
CARRIER
CTRLR 0
REMOTE
DETECT
ALARM
ALARM
100Mbps
LOCAL
BACK
LOOP
COLL
LINK
FDX
EN
CE1/PRI-U
H7471
unbalanced connections
with BNC connectors
at the network end
E1 CSU
BNC connectors
LED Meaning
RA Local alarm at remote end of connection
LA Loss of signal, loss of frame, or unavailability because of
excessive errors
LP Controller local loopback
CD Carrier received on telco link
Figure 7-19 1-Port Channelized T1/E1 PRI Network Module with G.703 LEDs
NM-1CE1T1-PRI
RX TX CD LP
MON MON
T1
RA AIM
E1-BAL
C0 LA E1-UNBAL EN
88737
CTLR 0
T1
E1-BAL
C0
E1-UNBAL
Figure 7-20 2-Port Channelized T1/E1 PRI Network Module with G.703 LEDs
NM-2CE1T1-PRI
CD LP RX TX CD LP
MON MON
T1 T1
RA C1 RA AIM
E1-BAL E1-BAL
LA E1-UNBAL C0 LA E1-UNBAL EN
88738
CTLR 1 CTLR 0
T1 T1
E1-BAL CTRL 1 E1-BAL
E1-UNBAL CTRL 0 E1-UNBAL
Table 7-5 Channelized T1/E1 PRI Network Module with G.703 LEDs
cT1
PRI
LOOPBACK
CARRIER
REMOTE
DETECT
ALARM
ALARM
LOCAL
EN
H7462
CTRLR 0
Enable LED
CT1/PRI LEDs
CT1/PRI LEDs
LOOPBACK
CARRIER
cT1
REMOTE
DETECT
ALARM
ALARM
LOCAL
PRI
CTRLR 1
LOOPBACK
CARRIER
REMOTE
DETECT
ALARM
ALARM
LOCAL
EN
H7463
CTRLR 0
cT1
CSU
RX TX RX
OUT IN MON
LOOPBACK
CARRIER
REMOTE
DETECT
ALARM
ALARM
LOCAL
EN
H7467
CTRLR 0
LOOPBACK
cT1
CARRIER
REMOTE
DETECT
ALARM
ALARM
LOCAL
CSU
CTRLR 1
RX TX RX
OUT IN MON
LOOPBACK
CARRIER
REMOTE
DETECT
ALARM
ALARM
LOCAL
EN
H7466
CTRLR 0
cE1
PRI
LOOPBACK
CARRIER
REMOTE
DETECT
ALARM
ALARM
LOCAL
EN
H7262
CTRLR 0
Enable LED
CE1/PRI LEDs
CARRIER
cE1
REMOTE
DETECT
ALARM
ALARM
LOCAL
PRI
CTRLR 1
LOOPBACK
CARRIER
REMOTE
DETECT
ALARM
ALARM
LOCAL
EN
H7263
CTRLR 0
Note All Cisco PRI network modules have OIR support, but OIR is supported only on Cisco 3660 and
Cisco 3745 platforms.
Caution Cisco routers support OIR with similar modules only. If you remove a network module, install
another module exactly like it in its place. If you remove a network module with an installed interface
card, expansion module, or AIM, the replacement module should have the same hardware installed.
For a description of informational and error messages that may appear on the console during this
procedure, refer to the hardware installation guide for your type of router.
Note Channelized T1/E1 PRI network modules with G.703 provide full support for Cisco digital modem
network modules.
If your PRI module is the wrong revision, you see a message similar to the following message when the
router boots:
The PRI network module in slot 0 is incompatible with the digital modems installed in the
router.
To determine the revision level, you can examine the network module itself (outside the router) or use
the Cisco IOS show diag command. The label on the module board should show a part number
beginning with 800- and ending with the revision level.
The output of the show diag command looks similar to the following:
Port adapter is analyzed
Port adapter insertion time unknown
Hardware revision 1.0 Board revision A0
Serial number 4152626 Part number 800-01236-01
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 26 01 00 00 3F 5D 32 50 04 CC 01 00 00 00 00
0x30: 50 00 00 00 96 11 04 17 FF FF FF FF FF FF FF FF
Related Documents
For additional information, refer to the following documents.
Tip For information on obtaining documentation, see the Obtaining Documentation section on page xxv.
For information on obtaining technical assistance, see the Obtaining Technical Assistance section on
page xxvii. For information on additional information, see the Obtaining Additional Publications and
Information section on page xxix.
Hardware Documentation
For the Cisco 2600 series, refer to documents listed under Cisco 2600 Series Routers.
For the Cisco 3600 series, refer to documents listed under Cisco 3600 Series Routers.
For the Cisco 3700 series, refer to documents listed under Cisco 3700 Series Routers.