MANUAL
DECLARATION OF CONFORMITY
The following manufacturer is responsible for this declaration
AUTOCLAVE STERILIZER
SA-200, SA-230, SA-300E, SA-252, SA-252F, SA-230X, SA-300H, SA-300VF, SA-300VL, SA-200F, SA-230F,
SA-230FA, SA-260FA, SA-300FA, SA-300VFA, SA-100, SA-252M, SA-300V, SA-300VA, SA-230MA,
SA-252MA, SA-230M, SA-260M, SA-300M, SA-260MA, SA-300MA, SA-300VM, SA-300VMA, SA-200J,
SA-230J, SA-252J, SA-202, SA-202X, SA-202V, SA-302E, SA-232, SA-232X, SA-232V, SA-252X
are in conformity with the requirements of Medical Devices Directive (93/42/EEC) Annex
I and Annex VII.
Representation in EU:
VADES
MRS. G.J.E. VAN DER SMITE
LAAN VAN POOT 146
2566 ED DEN HAAG
THE NETHERLANDS
TEL: +31 70 3454535 FAX: +31 76 3652403
E-MAIL: wendy.vandersmitte@planet.nl
Note: This declaration becomes invalid if technical or operational modifications are introduced
without the manufacturers consent.
SIGNATURE
MARVIN SHIEH
In the capacity of General Manager and duly authorized to sign this Declaration on behalf of
STURDY INDUSTRIAL CO., LTD.
20 December 2006, TAIWAN
PLACE and DATE issued
NO. 168, SEC. 1, ZHONGXING RD., WUGU SHIANG, TAIPEI COUNTY 24872, TAIWAN
TEL: +886-2-29837622 FAX: +886-2-29848208 E-mail: foreign@sturdy.com.tw WEBSITE: www.sturdy.com.tw
OPERATION
MANUAL
CONTENTS
Please read this manual carefully prior using your new Autoclave. Following
simple instructions contained in this manual will help to ensure ease of use, trouble free
operation, and a longer working life for your Autoclave.
---------------------------------------------------------------------------------------------------------------------------------------
CHAPTER 2. SPECIFICATION................................................................................. P. 2
CHAPTER 5. WARNING........................................................................................... P. 5
CHAPTER 6. APPENDIX.......................................................................................... P. 6
---------------------------------------------------------------------------------------------------------------------------------------
422-02006-01
CHAPTER1 LOCATION
Exhaust valve
Door
Control panel
Pressure gauge
CONTROL PANEL
SELEC
POWER
SWITCH
- P.1
CHAPTER1 LOCATION
CONTROL PANEL
- P.1-1
CHAPTER 2 SPECIFICATION
SPECIFICATION OF
MODEL NO. SA-232 SA-202
- P.2 -
CHAPTER3. PREPARATION
TOP
CHECKLIST FOR UNPACKING INSTRUCTIONS:
TO UNPACK AUTOCLAVE FROM CARTON
1. Remove Straps. WALL
2. Remove top of carton.
3. Remove wall-piece of the carton.
4. Remove foam-packing pieces.
1. Put this autoclave on table, and keep the distance more than 5cm between the wall
and the case. And keep this autoclave in level condition.
2. Check the elec. power source must be 110V, 220V or 240V.
110V power cord type: 14 AWG x 3C CSA or U/L.
220V power cord type: 0.75mm x 3C TUV
240V power cord type: 0.75mm x 3C SAA
3. Pouring the water (DISTILLED WATER ONLY) into chamber, until the water
level near the door side.
CAUTION: THE WATER LEVEL MUST COVER THE HEATER.
Water level
4. You are now, ready to take the power cord, and plug into a standard grounded AC
outlet.
5. Check the power lamp, if it is on, that means the power is already stand-by now.
- P. 3-
CHAPTER 4 OPERATION
1. Open the door and pouring water until the water level fully covers the heater. Then turn to
close the exhaust valve.
2. Put the sterilized instruments on trays or in sterilization box. Or spring
holder as you need.
3. Then put the box (or tray, or spring holder) into the chamber.
PLEASE DONT FORGET TO PUT THE STERILIZATION INDICATOR
IN CHAMBER.
4. Close the door, turning the handle to tight. Then turn power on.
5. Press the SELECT to choose the sterilization time. And press the START button to
work.
Please notethe sterilization time was set up in the program 15 minutes / 30 minutes.
So the user can select the sterilization time by SELECT button. And then push the
START button, the heating lamp will be on.
PS: Please dont open the door immediately, after completion. Because the chamber
still with pressure.
8. Turn the exhaust valve to open, in order to release the chamber pressure, until the
pressure returns to o (zero), Then, open the door.
PS: If the door cant be opened, chamber is in vacuum condition. Please exhaust valve to
release the vacuum in chamber.
- P.4 -
CHAPTER 4. BASIC STEP OF STERILIZING
POUR WATER IN THE CHAMBER (WATER LEVEL MUST COVER THE HEATER COMPLETELY)
- P.4-1 -
CHAPTER 5 WARNING
1. Please check the pressure gauge, if the pressure over than 0 kg/cm. Please dont open
door.
2. USE ONLY DISTILLED WATER for this autoclave. Or not, we cant offer the quality
guarantee service.
3. Please pour the water into the chamber, before sterilization. Or not, the low water
protector wills cut-off the elec. power.
PS: Please TURN OFF the power switch, and pour water in the chamber.
4. Then, close the door and TURN ON the power switch again.
5. Please attend the high temperature around the chamber. When she is working.
6. The door handle must touching the stop metal, which on the screw of the handle, when
you close the door.
7. Ensure the heater inside the chamber is covered with water prior to commencement of
the sterilization cycle.
8. Use only a indicated power supply as per plug.
9. The silicon gasket inside inner door and the front plate of the chamber should be kept
clean to maintain maximum life.
10. We recommend use of chemical indicator strips as a check for sterility. These strips may
also be kept as a record of sterilization.
11. In the event of an emergency immediately turn the power off. Then, turn open the
exhaust valve.
12. THE SIGN OF CAUTION AND INDICATION:
- P.5 -
CHAPTER 6 APPENDIX A
Liquid sterilization is available, but it must adjust the exhaust valve limited
and arrange the pressure down to 0 in 5 minutes.
- P.6 -
CHAPTER 6 APPENDIX B
2. Remove power cord and place all items into the chamber. Close door secure firmly.
4. Place the bottom of the carton containing the packing bottom foam on the floor.
5. Place the autoclave into the packing bottom foam ensuring that the door of the
6. Place the wall piece of carton into the bottom of the carton.
7. Place the packing fix foam into the back and front of door.
11. Tie carton together with heavy twine or a similar strong material.
IMPORTANT: We strongly recommend that all packing material including the carton
be kept for re-use in the event that the unit needs to be transported at any time.
- P.6-1-
CHAPTER 6. APPENDIX - C
Item (DESCRIPTION)
PART NO.
1 001-01004-01 SA-300()1.5mm^3C Power cord(AC230V)
- P.6-2-
CHAPTER 7 TROUBLE SHOOTING
- P.7 -
CHAPTER 8 MAINTENANCE REQUIREMENTS
DAILY:
WIPE THE INSIDE OF THE CHAMBER AND THE INSIDE OF THE DOOR
WITH A NON-LINT CLOTHE SUCH AS A WETTED.
CHECK AND KEEP THE DOWN SIDE (IN THE CHAMBER SIDE) OF THE
SAFETY VALVE AND STEAM TRAP TO BE CLEAN.
WEEKLY:
EMPTY THE BALANCE WATER IN THE CHAMBER AND CLEAN THE
RACK AND TRAYS.
TRY TO PULL THE SAFETY VALVE WITH THE RINGLET. TO CHECK AND
KEEP THE SAFETY VALVE IN WORKING CONDITION.
MONTHLY:
EMPTY THE BALANCE WATER IN THE CHAMBER, AND CLEAN THE
SURFACE OF THE CHAMBER AND THE SURFACE OF THE HEATER,
WITH CHAM-MATE OR A LITTER SOUP. THEN, WATER CLEANS
AGAIN.
- P.8 -
WARRANTY
Your STURDY product has a one (1) year guarantee of defective in materials and
workmanship under normal use from the date of purchase.
This warranty does not apply to any product damaged by accident misuse, abuse
neglect improper line voltage drop fire flood. Or the products were altered or repaired by
anyone other than qualified service personnel.
The liability of Sturdy Industrial Co. Ltd. is limited to repair of replacement and under no
circumstances shall STURDY be liable for any collateral consequential damages or loss.
This guarantee specifically excludes the expendables and consumable.
All warranty claims must be directed to the distributors or agents authorized by Sturdy
Industrial Co.Ltd. whom are responsible for the sales of this equipment. The customers
are responsible for shipping expense.
__________________________________________________________
Country: _____________ Tel: ______________ Fax: ______________
Date of Purchase: _____________ Model No.: ____________________
Series No.: _________________________________________________
Distributor: