Anda di halaman 1dari 28

BRITISH STANDARD BS EN

14606:2004

Inland navigation
vessels Studless
anchor chain
Accessories

The European Standard EN 14606:2004 has the status of a


British Standard

ICS 47.020.50; 47.060

12&23<,1*:,7+287%6,3(50,66,21(;&(37$63(50,77('%<&23<5,*+7/$:
BS EN 14606:2004

National foreword
This British Standard is the official English language version of
EN 14606:2004.
The UK participation in its preparation was entrusted by Technical Committee
SME/32, Ships and marine technology, to Subcommittee SME/32/7, Inland
navigation vessels, which has the responsibility to:

aid enquirers to understand the text;


present to the responsible international/European committee any
enquiries on the interpretation, or proposals for change, and keep the
UK interests informed;
monitor related international and European developments and
promulgate them in the UK.

A list of organizations represented on this subcommittee can be obtained on


request to its secretary.
Cross-references
The British Standards which implement international or European
publications referred to in this document may be found in the BSI Catalogue
under the section entitled International Standards Correspondence Index, or
by using the Search facility of the BSI Electronic Catalogue or of
British Standards Online.
This publication does not purport to include all the necessary provisions of a
contract. Users are responsible for its correct application.
Compliance with a British Standard does not of itself confer immunity
from legal obligations.

Summary of pages
This document comprises a front cover, an inside front cover, the EN title page,
pages 2 to 24, an inside back cover and a back cover.
The BSI copyright notice displayed in this document indicates when the
document was last issued.

Amendments issued since publication


This British Standard was
published under the authority Amd. No. Date Comments
of the Standards Policy and
Strategy Committee on
26 October 2004

BSI 26 October 2004

ISBN 0 580 44648 4


EUROPEAN STANDARD EN 14606
NORME EUROPENNE
EUROPISCHE NORM September 2004

ICS 47.020.50; 47.060

English version

Inland navigation vessels - Studless anchor chain - Accessories

Bateaux de navigation intrieure - Chane d'ancre sans Fahrzeuge der Binnenschifffahrt - Steglose Ankerkette -
pignon - Accessoires Zubehr

This European Standard was approved by CEN on 29 July 2004.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.

CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION


COMIT EUROPEN DE NORMALISATION
EUROPISCHES KOMITEE FR NORMUNG

Management Centre: rue de Stassart, 36 B-1050 Brussels

2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14606:2004: E
worldwide for CEN national Members.
EN 14606:2004 (E)

Contents Page

Foreword .......................................................................................................................................................3
1 Scope ................................................................................................................................................4
2 Normative references .......................................................................................................................4
3 Terms and definitions ......................................................................................................................4
4 Requirements ...................................................................................................................................5
4.1 Components .....................................................................................................................................5
4.1.1 Joining link .......................................................................................................................................5
4.1.2 Common link ....................................................................................................................................7
4.1.3 Enlarged link.....................................................................................................................................8
4.1.4 End link.............................................................................................................................................9
4.1.5 Chain swivel ...................................................................................................................................10
4.1.6 End shackle ....................................................................................................................................12
4.1.7 Swivel shackle................................................................................................................................14
4.1.8 Kenter-type joining shackle ...........................................................................................................16
4.2 Assemblies .....................................................................................................................................17
4.2.1 Anchor swivel .................................................................................................................................17
4.2.2 Swivel shackle................................................................................................................................17
4.2.3 Swivel outboard shot .....................................................................................................................17
5 Construction...................................................................................................................................17
5.1 Materials .........................................................................................................................................17
5.2 Strength and mechanical properties .............................................................................................18
6 Testing ............................................................................................................................................18
6.1 Strength test ...................................................................................................................................18
6.2 Dimensions.....................................................................................................................................18
7 Designation.....................................................................................................................................19
8 Marking ...........................................................................................................................................19
Annex A (informative) Examples of connections of the studless anchor chain to the anchor ..............20
A.1 Anchor swivel with joining link......................................................................................................20
A.2 Swivel shackle with joining link.....................................................................................................21
A.3 Swivel outboard shot with joining link and end shackle ..............................................................22
A.4 Swivel outboard shot with Kenter-type joining shackle and end shackle ...................................23
Bibliography................................................................................................................................................24

2
EN 14606:2004 (E)

Foreword

This document EN 14606:2004 has been prepared by Technical Committee CEN/TC 15 Inland navigation
vessels, the secretariat of which is held by DIN.

This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by March 2005, and conflicting national standards shall be withdrawn at
the latest by March 2005

This document contains a bibliography.

.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland
and the United Kingdom.

3
EN 14606:2004 (E)

1 Scope

This document applies to accessories used with round steel chains as specified in EN 14330 as studless
anchor chains for inland navigation vessels.

It specifies the construction, dimensions and testing of accessories such as joining links and end links, chain
swivels, end shackles, swivel shackles and Kenter-type joining shackles.

It does not apply to anchor equipment consisting of cable stoppers, cable lockers or end fastenings, for
example.

2 Normative references

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

EN 10243-1, Steel die forgings Tolerances on dimensions Part 1: Drop and vertical press forgings.

EN 14330, Inland navigation vessels Studless anchor chain Round steel chain.

EN 22339, Taper pins, unhardened (ISO 2339:1986).

EN ISO 7046-2, Cross-recessed countersunk flat head screws (common head style) Product grade A
Part 2: Steel of property class 8.8, stainless steel and non-ferrous metal (ISO 7046-2:1990).

ISO 1704, Shipbuilding Stud-link anchor chains.

ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individual
tolerance indications.

3 Terms and definitions


For the purposes of this document, the following terms and definitions apply.

3.1
joining link
single link for joining the round steel chain to anchor swivel (3.10) or swivel shackle (3.7) or swivel outboard
shot (3.9)

3.2
common link
single link for joining the swivel outboard shot (3.9) to connecting link (3.1) or Kenter-type joining shackle
(3.8)

3.3.
enlarged link
single link for joining a chain swivel (3.5) to common link (3.2) or end link (3.4)

3.4
end link
single link for joining an enlarged link (3.3) to end shackle (3.6)

4
EN 14606:2004 (E)

3.5
chain swivel
rotatable connection in the swivel outboard shot (3.9) of a studless anchor chain

3.6
end shackle
bracket with oval bolt in the swivel outboard shot (3.9) of a studless anchor chain

3.7
swivel shackle
rotatable connection between round steel chain and anchor

3.8
Kenter-type joining shackle
connecting element for making a detachable connection between round steel chain and swivel outboard shot
(3.9)

NOTE Kenter was the inventor of this shackle.

3.9
swivel outboard shot
component of the studless anchor chain joining the round steel chain and anchor to the twist compensator

3.10
anchor swivel
rotatable non-detachable element on the anchor shaft

3.11
anchor shackle
rotatable, but non-detachable, element on the anchor shaft for connecting to the round steel chain through
swivel outboard shot (3.9)

4 Requirements
4.1 Components
4.1.1 Joining link
For dimensions of joining links (3.1), see Figure 1 and Table 1.

Figure 1 Joining link

5
EN 14606:2004 (E)

Table 1 Nominal dimensions and masses of joining links


a b
Nominal size Diameter Pitch Internal width Mass
dp d1 p1 w1 G
mm mm mm Mm kg

10 28 13 55 25 0,19
13 36 16 70 30 0,36

16 45 20 90 40 0,7
18 50 23 100 45 1,1

20 56 26 115 50 1,5
23 64 28 125 55 1,9

26 73 32 140 65 2,9
28 78 36 160 70 4,1

30 84 38 165 75 4,8
33 92 40 175 80 5,6

36 101 45 200 90 8
39 109 48 210 95 9,7
100 11
42 118 50 220
a
Nominal size d p according to EN 14330.
b
Nominal dimensions in millimetres (mm) and masses, in kilograms (kg), are
calculated as follows:
p1 = 4,4 d1; G = 87,7 d13 10-6; w1 = 6,8 WF 0,5, WF = 0,141 x d2
according to EN 14330.

6
EN 14606:2004 (E)

4.1.2 Common link

For dimensions of the common link (3.2) as shown in Figure 1 and Table 1 of ISO 1704:1991, see Figure 2
and Table 2.

Figure 2 Common link

Table 2 Nominal dimensions and masses of common links


a
Nominal size Diameter Pitch External width Mass b Nominal
diameter to
c
ISO 1704
dxp d1 p1 w2 G D
mm mm mm mm kg Mm
13 36 12,5 50 45 0,17 12,5
16 45 16 64 58 0,36 16
18 50 17,5 70 63 0,47 17,5
20 56 20,5 82 74 0,75 20,5
23 64 22 88 79 0,93 22
26 73 26 104 94 1,5 26
28 78 28 112 101 1,9 28
30 84 30 120 108 2,4 30
33 92 32 128 115 2,9 32
36 101 36 144 130 4,1 36
39 109 38 152 137 4,8 38
42 118 42 168 151 6,5 42
a
Nominal size d p according to EN 14330.
b
Nominal dimensions in millimetres (mm) and masses, in kilograms (kg), are calculated as follows:
p1 = 4 d1; w2 = 3,6 d1; G = 87,6 10 6 d13
c
Nominal diameter assigned to the nominal size according to ISO 1704:1991, Table 1.

7
EN 14606:2004 (E)

4.1.3 Enlarged link

For dimensions of the enlarged link (3.3), according to Figure 2 and Table 2 of ISO 1704:1991, see Figure 3
and Table 3.

Figure 3 Enlarged link

Table 3 Nominal dimensions and masses of enlarged links


a
Nominal size Diameter Pitch External Mass b Nominal
width diameter to
ISO 1704 c
dp d1 p1 w2 G D
mm Mm mm mm kg Mm
13 36 14 56 50 0,24 12,5
16 45 17,5 70 63 0,47 16
18 50 19 76 68 0,60 17,5
20 56 22 88 79 0,93 20,5
23 64 24 96 86 1,2 22
26 73 28 112 101 1,9 26
28 78 30 120 108 2,4 28
30 84 34 136 122 3,4 30
33 92 36 144 130 4,1 32
36 101 40 160 144 5,6 36
39 109 42 168 151 6,5 38
42 118 46 184 166 8,5 42
a
Nominal size d p according to EN 14330.
b
Nominal dimensions in millimetres (mm) and masses, in kilograms (kg), are calculated as
follows: d1 = 1,1 D; p1 = 4 d1; w2 = 3,6 d1; G = 87,6 10 d1 .
6 3

c
Nominal diameter assigned to the nominal size according to ISO 1704:1991, Table 1.

8
EN 14606:2004 (E)

4.1.4 End link

For dimensions of the end link (3.4), according to Figure 3 and Table 3 of ISO 1704:1991, see Figure 4 and
Table 4.

Figure 4 End link

Table 4 Nominal dimensions and masses of end links


a
Nominal size Diameter Pitch External Mass b Nominal
width diameter to
c
ISO 1704
dp d1 p1 w2 G D
mm mm mm mm kg Mm

13 36 16 54 50 0,17 12,5
16 45 19 70 64 0,36 16
18 50 20,5 76 70 0,47 17,5
20 56 24 89 82 0,76 20,5
23 64 26 96 88 0,94 22
26 73 32 113 104 1,5 26
28 78 34 122 112 1,9 28
30 84 36 131 120 2,4 30
33 92 38 139 128 2,9 32
36 101 44 157 144 4,1 36
39 109 46 165 152 4,8 38
42 118 50 183 168 6,5 42
a
Nominal size d p according to EN 14330.
b
Nominal dimensions in millimetres (mm) and masses in kilograms (kg) are
calculated as follows: d1 = 1,2 D; p1 = 4,35 D; w2 = 4 D; G = 81,4 10-6 D3.
c
Nominal diameter assigned to the nominal size according to ISO 1704:1991, Table 1.

9
EN 14606:2004 (E)

4.1.5 Chain swivel

For dimensions of chain swivels (3.5), see Figure 5 and Table 5.


The bearing surface of the nut shall be capable of accommodating any possible movement of the swivel body.

Key

1 Swivel body
2 Eye-bolt with nut

Figure 5 Chain swivel

10
EN 14606:2004 (E)

Table 5 Nominal dimensions and masses of chain swivels

Nominal
b size to
Nominal Mass
size
a ISO 1704c

D
dxp a b c d1 d2 d3 e f l1 l2 G mm
mm mm mm mm mm mm mm mm mm mm mm kg
13 x 36 59 43 22 14 15 18 18 25 121 42 0,70 12,5
16 x 45 75 54 28 18 19 23 22 32 155 54 1,5 16
18 x 50 82 60 31 19 21 25 25 35 170 59 1,9 17,5
20 x 56 96 70 36 23 25 30 29 41 199 69 3,1 20,5
23 x 64 103 75 39 24 26 32 31 44 213 74 3,8 22
26 x 73 122 88 46 29 31 38 36 52 252 87 6,3 26
28 x 78 132 95 49 31 34 41 29 56 272 94 7,9 28
30 x 84 141 102 53 33 36 44 42 60 291 101 9,7 30
33 x 92 150 109 56 35 38 46 45 64 310 107 12 32
36 x 101 169 122 63 40 43 52 50 72 349 121 17 36
39 x 109 179 129 67 42 46 55 53 76 369 127 20 38
42 x 118 197 143 74 46 50 61 59 84 407 141 27 42
a
Nominal size d p according to EN 14330.
b
Nominal dimensions in millimetres (mm) and the masses, in kilograms (kg), are calculated as follows:
a = 4,7 D; b = 3,4 D; c = 1,75 D; d1 = 1,1 D; d2 = 1,2 D; d3 = 1,45 D; e = 1,4 D; f = 2,0 D;
l1 = 9,7 D; l2 = 3,35 D; G = 360 10 D .
6 3
c
Nominal diameter assigned to the nominal size according to ISO 1704:1991, Table 1.

11
EN 14606:2004 (E)

4.1.6 End shackle

For dimensions of end shackles (3.6), as shown in Figure 4 and Table 4 in ISO 1704:1991, see Figure 6 and
Table 6.
The bolt is secured by a tin-plated taper pin, Form B, to EN 22339. The hole shall by plugged with lead to
prevent corrosion of the pin.
End shackles comprise the bracket and the oval unscrewable bolt.

Key

1 Taper pin, form B, according to EN 22239


2 Bolt
3 Bracket
Figure 6 End shackle

12
EN 14606:2004 (E)

Table 6 Nominal dimensions and masses of end shackles

Nominal
diameter
Nominal Taper pin
a
Mass according
size EN 22339, to
c
ISO1704
dxp Form B
a b1 b2 b3 b4 c d1 k l Gb D
mm mm mm mm mm mm mm mm mm mm kg mm
13 x 36 23 65 30 39 18 11 18 2,5 58 B 5x 30 0,7 12,5
16 x 45 28 83 38 50 22 14 22 3 74 B 6x 40 1,5 16
18 x 50 32 91 42 54 25 16 25 3,5 81 B 6x 40 1,9 17,5
20 x 56 37 107 49 64 29 18 29 4 94 B 8x 50 3,1 20,5
23 x 64 40 114 53 68 31 20 31 4,5 101 B 8x 50 3,8 22
26 x 73 47 135 62 81 36 23 36 5 120 B 10 x 60 6,3 26
28 x 78 50 146 67 87 39 25 39 5,5 129 B 10 x 65 7,9 28
30 x 84 54 156 72 93 42 27 42 6 138 B 12 x 70 9,7 30
33 x 92 58 166 77 99 45 29 45 6,5 147 B 12 x 75 12 32
36 x 101 65 187 86 112 50 32 50 7 166 B 12 x 90 17 36
39 x 109 68 198 91 118 53 34 53 7,5 175 B 16 x 85 20 38
42 x 118 76 218 101 130 59 38 59 8,5 193 B 16 x 100 27 42
a
Nominal size according to EN 14330.
b
Nominal dimensions in millimetres (mm) and masses, in kilograms (kg), are calculated as follows:
a = 1,8 D; b1 = 5,2 D; b2 = 2,4 D; b3 = 3,1 D; b4 = 1,4 D; c = 0,9 D; d1 = 1,4 D; k = 0,2 D,
l = 4,6 D; G = 360 10 6 D3
c
Nominal diameter assigned to the nominal size according to ISO 1704:1991, Table 1.

13
EN 14606:2004 (E)

4.1.7 Swivel shackle

For dimensions of swivel shackles (3.7), see Figure 7 and Table 7.

The swivel shackle is an alternative to the swivel outboard shot. The bearing surface of the nut shall be
capable of accommodating any possible

movement of the fork.

Key

1 Anchor-side fork
2 Chain-side fork
3 Nut, welded to fork
4 Anchor bolt, fitted
5 Chain bolt, fitted
6 Cover plate, welded
7 Countersunk screw to EN ISO 7046-2, cross-recessed Form H
8, 9 Taper pin Form B to EN 22339, tin-plated, plugged with lead

Figure 7 Swivel shackle

14
EN 14606:2004 (E)

Table 7 Nominal dimensions and masses of the swivel shackle


Nominal
a
size a1 a2 b1 b2 b3 b4 b5 b6 c1 c2 d1 d2
dxp
mm mm mm mm mm mm mm mm mm mm mm mm
13 x 36 23 19 30 18 18 18 16 15 11 10 50 M 20
16 x 45 29 24 38 22 22 22 21 19 14 13 64 M 24
18 x 50 32 26 42 25 25 25 23 21 16 14 70 M 27
20 x 56 37 31 49 29 29 29 27 25 18 16 82 M 30
23 x 64 40 33 53 31 31 31 29 26 20 18 88 M 33
26 x 73 47 39 62 36 36 36 34 31 23 21 104 M 39
28 x 78 50 42 67 39 39 39 36 34 25 22 112 M 42
30 x 84 54 45 72 42 42 42 39 36 27 24 120 M 45
33 x 92 58 48 77 45 45 45 42 38 29 26 128 M 48
36 x 101 65 54 86 50 50 50 47 43 32 29 144 M 56
39 x 109 68 57 91 53 53 53 49 46 34 30 152 M 60
42 x 118 76 63 101 59 59 59 55 50 38 34 168 M 64

Nominal Screw Taper pin Mass b Nominal


a
size k l1 l2 l3 r1 r2 EN 22339 G size to
dxp ISO
mm 1704 c
mm mm mm mm mm mm Item. No. Item. No. 8 Item No.9 kg
7 D
13 x 36 2,5 94 30 18 23 21 M4x8 B 5 x 32
B 5 x 37 2,1 12,5
16 x 45 3 120 38 22 29 26 M4x8 B 6 x 40
B 6 x 45 4,5 16
18 x 50 3,5 131 42 25 32 28 M4x8 B 6 x 45
B 6 x 55 5,8 17,5
20 x 56 4 154 49 29 37 33 M4x8 B 8 x 50
B 8 x 60 9,4 20,5
23 x 64 4,5 165 53 31 40 35 M4x8 B 8 x 55
B 8 x 65 12 22
26 x 73 5 195 62 36 47 42 M 4 x 10 B 10 x 75
B 10 x 65 19 26
28 x 78 5,5 210 67 39 50 45 M 4 x 10 B 10 x 85
B 10 x 70 24 28
30 x 84 6 225 72 42 54 48 M 6 x 16 B 12 x 85
B 12 x 75 29 30
33 x 92 6,5 240 77 45 58 51 M 6 x 16 B 12 x 80
B 12 x 95 36 32
36 x 101 7 270 86 50 65 58 M 6 x 16 B 12 x 95
B 12 x 51 36
100
39 x 109 7,5 285 91 53 68 61 M 6 x 16 B 16 x 95 B 16 x 60 38
42 x 118 8,5 315 101 59 76 67 M 10 x 20 B 16 x100 100 81 42
B 16 x
120
a
Nominal size d p according to EN 14330.
b
Nominal dimensions in millimetres (mm).and the masses, in kilograms (kg), are calculated as follows a1 = 1,8 D;
a2 = 1,5 D; b1 = 2,4 D; b2 = 1,4 D; b3 = 1,4 D; b4 = 1,4 D; b5 = 1,3 D; b6 = 1,2 D; c1 = 0,9 D;
d1 = 4 D; k = 0,2 D; l1 = 7,5 D; l2 = 2,4 D; l3 = 1,4 D; r1 = 1,8 D; r2 = 1,6 D; G = 1,09 D 10 .
3 3

c
Nominal diameter assigned to the nominal size according to ISO 1704:1991, Table 1.

15
EN 14606:2004 (E)

4.1.8 Kenter-type joining shackle

For dimensions of Kenter-type joining shackles (3.8), as shown in Figure 5 and Table 5 in ISO 1704:1991, see
Figure 8 and Table 8..
The Kenter-type joining shackle is used on board for joining round steel chain and swivel shackle.

Key

1 Top
2 Taper pin, EN 22339, Form B
3 Bottom

Figure 8 Kenter-type joining shackle

16
EN 14606:2004 (E)

b
Table 8 Nominal dimensions and masses of the Kenter-type joining shackle
Nominal Nominal
a
size Mass
b
size to
Taper pin ISO1704
c

EN 22339 D
dxp a1 a2 b d h r1 r2 r3 t G
mm mm mm mm mm mm mm mm mm mm kg
13 x 36 19 15 53 12,5 17 23 56 8,4 50 B 5 45 0,27 12,5
16 x 45 24 19 67 16 21 29 72 10,5 64 B 6 55 0,57 16
18 x 50 27 21 74 17,5 23 32 79 11,5 70 B 6 60 0,75 17,5
20 x 56 31 25 86 20,5 27 38 92 13,5 82 B 8 70 1,2 20,5
23 x 64 33 26 92 22 29 40 99 14,5 88 B 8 75 1,5 22
26 x 73 40 31 109 26 35 48 117 17,5 104 B 10 90 2,5 26
28 x 78 43 34 118 28 38 51 126 19 112 B 10 100 3,1 28
30 x 84 46 36 126 30 40 55 135 20 120 B 12 100 3,8 30
33 x 92 49 38 134 32 43 59 144 21,5 128 B 12 120 4,6 32
36 x 101 55 43 151 36 48 66 162 24 144 B 12 120 6,5 36
39 x 109 58 46 160 38 51 70 171 25,5 152 B 16 120 7,7 38
42 x 118 64 50 176 42 56 77 189 28 168 B 16 140 10 42
a
Nominal size d p according to DIN 14330.
b
Nominal dimensions in millimetres (mm) and masses, in kilograms (kg), are calculated as follows:
a1 = 1,52 D, a2 = 1,2 D; b = 4,2 D; d = 1 D; h = 1,34 D; r1 = 1,83 D; r2 = 4,5 D; r3 = 0,67 D; t = 4 D; G
= G = 140 D3 10-6, taper pin diameter dKeg = 0,37 x D; taper pin length lKeg = b 2 x dKeg.
c
Nominal diameter assigned to the nominal size according to ISO 1704:1991, Table 1.

4.2 Assemblies

4.2.1 Anchor swivel

This assembly consists of joining link (3.1) to the round steel chain and the non-detachable anchor swivel
(3.10) secured to the anchor, see Figure A.1.

4.2.2 Swivel shackle

This assembly consists of joining link (3.1) to the round steel chain and swivel shackle (3.7) with non-
detachable anchor shackle secured to the anchor, see Figure A.2.

4.2.3 Swivel outboard shot

This assembly consists of chain swivel (3.5) with enlarged link (3.3), common link (3.2) and joining link (3.1) to
the round steel chain and enlarged link (3.3) and end link (3.4) on the end shackle (3.6) for joining to the non-
detachable anchor shackle secured to the anchor, see Figure A.3.

5 Construction

5.1 Materials

Materials of at least strength grade 2 are the basis of accessories for studless anchor chains.

17
EN 14606:2004 (E)

5.2 Strength and mechanical properties

Accessories for studless anchor chains shall have at least the strength and mechanical properties specified in
EN 14330 and shall be heat treated as specified in 4.3 of EN 14330:2003

6 Testing
6.1 Strength test
The strength test shall be carried out as described in clause 5 of EN 14330:2003.

6.2 Dimensions

Dimensions shall correspond to the values given in Tables 1 to 8 taking into account the tolerances for:

a) forgings: forging grade F as specified in EN 10243-1 and

b) parts made by cutting: ISO 2768-c (in accordance with ISO 2768-1).

18
EN 14606:2004 (E)

7 Designation

Description of accessories and assemblies for studless anchor chains


enlarged link (3.3) (ISO 1704) LLk according to 4.1.3 and Figure 3
end link (3.4) (ISO 1704) ELk according to 4.1.4 and Figure 4
joining link (3.1) JLk according to 4.1.1 and Figure 1
common link (3.2) (ISO 1704) CLk according to 4.1.2 and Figure 2
anchor swivel (3.10) ASw according to 4.2.1 and Figure A.1
end shackle [bolt anchor shackle] (3.6) ESh according to 4.1.6 and Figure 6
(ISO 1704)
swivel outboard shot (3.9) SwO according to 4.2.3 and Figure A.3
swivel shackle (3.7) SwSh according to 4.1.7 and Figure 7
Kenter-type joining shackle (3.8) KJSh according to 4.1.8 and Figure 8
(ISO 1704)
chain swivel (3.5) CSw according to 4.1.5 and Figure 5

swivel shackle with joining link SwLk according to 4.2.2 and Figure A.2

EXAMPLE Designation of an accessory according to EN 1406 "end shackle" (ESh) as part of a joint of a round steel
chain d x p = 30 mm x 84 mm according to EN 14330 of strength grade 2, to a studless anchor chain.

Accessory EN 14606 ESh 30 x 84 2


The designation includes:

Description

Standard number

Accessory type

Nominal size of round steel chain according to EN 14330

Strength grade 2

8 Marking
The accessory shall be permanently marked, raised or embossed, for example with:

accessory type as symbol, e.g. ESh;


nominal size of the round steel chain according to EN 14330, e.g. 30 84;
strength grade 2;
standard number EN 14606;
manufacturer.

19
EN 14606:2004 (E)

Annex A
(informative)

Examples of connections of the studless anchor chain to the anchor

A.1 Anchor swivel with joining link

Figure A.1 shows an example.

Key

1 Round steel chain link according to EN 14330


2 Joining link (3.1) as described in 4.1.1, Figure 1
3 Non-detachable anchor swivel (3.10) on anchor

Figure A.1 Anchor swivel with joining link

20
EN 14606:2004 (E)

A.2 Swivel shackle with joining link

Figure A.2 shows an example.

Key

1 Round steel chain link according to EN 14330


2 Joining link (3.1) as described in 4.1.1, Figure 1
3 Swivel shackle (3.7) as described in 4.1.7, Figure 7
4 Non-detachable anchor shackle (3.11) on anchor

Figure A.2 Swivel shackle with joining link

21
EN 14606:2004 (E)

A.3 Swivel outboard shot with joining link and end shackle
Figure A.3 shows an example.

Key

1 Round steel chain link according to EN 14330


2 Joining link (3.1) as described in 4.1.1, Figure 1
3 Swivel outboard shot (3.9) as described in 4.2.3, Figure A.3 or Figure A.4
4 Common link (3.2) as described in 4.1.2, Figure 2
5 Enlarged link (3.3) as described in 4.1.3, Figure 3
6 Chain swivel (3.5) as described in 4.1.5, Figure 5
7 End link (3.4) as described in 4.1.4, Figure 4
8 End shackle (3.6) as described in 4.1.6, Figure 6
9 Non-detachable anchor shackle (3.11) on anchor

Figure A.3 Swivel outboard shot with joining link and end shackle

22
EN 14606:2004 (E)

A.4 Swivel outboard shot with Kenter-type joining shackle and end shackle

Figure A.4 shows an example.

Key

1 Round steel chain link according to EN 14330


2 Kenter-type joining shackle (3.8) as described in 4.1.8, Figure 8
3 Swivel outboard shot (3.9) as described in 4.2.3, Figure A.3 or Figure A.4
4 Common link (3.2) as described in 4.1.2, Figure 2
5 Enlarged link (3.3) as described in 4.1.3, Figure 3
6 Chain swivel (3.5) as described in 4.1.5, Figure 5
7 End link (3.4) as described in 4.1.4, Figure 4
8 End shackle (3.6) as described in 4.1.6, Figure 6
9 Non-detachable anchor shackle (3.11) on anchor

Figure A.4 Swivel outboard shot with Kenter-type joining shackle and end shackle

23
EN 14606:2004 (E)

Bibliography

[1] EN 13711, Inland navigation vessels - Winches for ship operation - Safety requirements.

[2] EN 13573, Inland navigation vessels - Anchoring, coupling, towing, hauling and mooring systems.

[3] prEN 14874, Inland navigation vessels Studless anchor chain Cable lifter.

[4] prEN (WI 00015044), Inland navigation vessels Studless anchor chain Anchor equipment.

24
blank
BS EN
14606:2004
BSI British Standards Institution
BSI is the independent national body responsible for preparing
British Standards. It presents the UK view on standards in Europe and at the
international level. It is incorporated by Royal Charter.

Revisions
British Standards are updated by amendment or revision. Users of
British Standards should make sure that they possess the latest amendments or
editions.
It is the constant aim of BSI to improve the quality of our products and services.
We would be grateful if anyone finding an inaccuracy or ambiguity while using
this British Standard would inform the Secretary of the technical committee
responsible, the identity of which can be found on the inside front cover.
Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.
BSI offers members an individual updating service called PLUS which ensures
that subscribers automatically receive the latest editions of standards.

Buying standards
Orders for all BSI, international and foreign standards publications should be
addressed to Customer Services. Tel: +44 (0)20 8996 9001.
Fax: +44 (0)20 8996 7001. Email: orders@bsi-global.com. Standards are also
available from the BSI website at http://www.bsi-global.com.
In response to orders for international standards, it is BSI policy to supply the
BSI implementation of those that have been published as British Standards,
unless otherwise requested.

Information on standards
BSI provides a wide range of information on national, European and
international standards through its Library and its Technical Help to Exporters
Service. Various BSI electronic information services are also available which give
details on all its products and services. Contact the Information Centre.
Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: info@bsi-global.com.
Subscribing members of BSI are kept up to date with standards developments
and receive substantial discounts on the purchase price of standards. For details
of these and other benefits contact Membership Administration.
Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001.
Email: membership@bsi-global.com.
Information regarding online access to British Standards via British Standards
Online can be found at http://www.bsi-global.com/bsonline.
Further information about BSI is available on the BSI website at
http://www.bsi-global.com.

Copyright
Copyright subsists in all BSI publications. BSI also holds the copyright, in the
UK, of the publications of the international standardization bodies. Except as
permitted under the Copyright, Designs and Patents Act 1988 no extract may be
reproduced, stored in a retrieval system or transmitted in any form or by any
means electronic, photocopying, recording or otherwise without prior written
permission from BSI.
This does not preclude the free use, in the course of implementing the standard,
of necessary details such as symbols, and size, type or grade designations. If these
details are to be used for any other purpose than implementation then the prior
BSI written permission of BSI must be obtained.
389 Chiswick High Road Details and advice can be obtained from the Copyright & Licensing Manager.
London Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553.
Email: copyright@bsi-global.com.
W4 4AL

Anda mungkin juga menyukai