Technical Information
Frame J
Design Series 45 Frame J pumps have a single servo piston design with a cradle-type swashplate
set in polymer-coated journal bearings. A bias spring and internal forces increase
swashplate angle. The servo piston decreases swashplate angle. Nine reciprocating
pistons displace fluid from the pump inlet to the pump outlet as the cylinder block
rotates on the pump input shaft. The block spring holds the piston slippers to the
swashplate via the slipper retainer. The cylinder block rides on a bi-metal valve plate
optimized for high volumetric efficiency and low noise. Tapered roller bearings support
the input shaft and a viton lip-seal protects against shaft leaks.
An adjustable one spool (PC only, not shown) or two spool (LS and PC) control senses
system pressure and load pressure (LS controls). The control ports system pressure to the
servo piston to control pump output flow.
LS control
(attached to endcap)
LS spool LS adjustment
PC spool PC adjustment
Valve
plate
Shaft seal
Cylinder
block
spring
Cylinder
block Slipper retainer
Ratings Model
Rating Units J45B J51B J60B J65C J75C
Input speed minimum min-1 (rpm) 500 500 500 500 500
continuous 2800 2700 2600 2500 2400
For definitions of pressure maximum 3360 3240 3120 3000 2880
and speed ratings, Working continuous bar [psi] 310 [4495] 310 [4495] 310 [4495] 260 [3770] 260 [3770]
see page 14. For more pressure maximum 400 [5800] 400 [5800] 400 [5800] 350 [5075] 350 [5075]
information on external External shaft External moment (Me) Nm [lbfin] 226 [2000] 226 [2000] 226 [2000] 226 [2000] 226 [2000]
shaft loads, see page 16; loads Thrust in (Tin), out (Tout) N [lbf ] 2200 [495] 2200 [495] 2200 [495] 2200 [495] 2200 [495]
mounting flange loads, Bearing life at 140 bar [2030 psi] B10 hours 29 712 29 712 29 712 10 755 10 755
see page 17. at 210 bar [3045 psi] 6834 6834 6834 2474 2474
at 260 bar [3770 psi] 3151 3151 3151
at 310 bar [4495 psi] 1666 1666 1666
Mounting flange Vibratory (continuous) Nm [lbfin] SAE-C: 1500 [14 000], SAE-B: 735 [6500]
load moments Shock (max) SAE-C: 5600 [50 000], SAE-B: 2600 [23 000]
1. Continuous input speeds are valid at 1 bar absolute [0 in Hg vac] inlet pressure. Maximum input speeds
require changing the inlet pressure or reducing pump displacement. See Inlet pressure vs. speed charts.
Sound levels
For more information on dB(A) 210 bar [3045 psi] 260 bar [3770 psi] 310 bar [4495 psi]
noise levels, see page 19. Model 1800 min-1 (rpm) Rated speed 1800 min-1 (rpm) Rated speed 1800 min-1 (rpm) Rated speed
J45B 75 79 77 80 76 80
J51B 75 79 77 78 77 78
J60B 75 79 77 79 76 79
J65C 75 78 77 77
J75C 77 78 77 77
2. Sound data was collected in a semi-anechoic chamber. Values have been adjusted (-3 dB) to reflect anechoic levels.
Flow (l/min)
100
of 17.8 mm/sec [88SUS]. 25
75 20
15
50
10
25
5
0 0
0 500 1000 1500 2000 2500 3000 3500
-1
Speed min (rpm) P104 206E
60 [37 80
Power (hp)
bar
260
60
40 psi]
30
ba r [20
140 40
20
20
0 0
0 500 1000 1500 2000 2500 3000 3500
-1
Speed min (rpm) P104 205E
various displacements.
Inlet Pressure (bar abs)
1.4 6
Greater speeds and lower 1.3 4
inlet pressures are possible 1.2
at reduced displacement. 2
1.1
Operating outside of
1.0 0
(in Hg vac)
150 40
Flow and power data valid
at 49C [120F] and viscosity
Flow (l/min)
100
75 20
50
10
25
0 0
0 500 1000 1500 2000 2500 3000 3500
-1
Speed min (rpm) P104 209E
60
Power (hp)
75
psi]
40 2030
bar [ 50
140
20 25
0 0
0 500 1000 1500 2000 2500 3000 3500
-1
Speed min (rpm) P104 208E
1.4 6
various displacements.
Greater speeds and lower 1.3 4
inlet pressures are possible 1.2
2
at reduced displacement. 1.1
Operating outside of 1.0 0
(in Hg vac)
Flow (l/min)
of 17.8 mm/sec [88SUS]. 125
30
100
75 20
50
10
25
0 0
0 500 1000 1500 2000 2500 3000 3500
-1
Speed min (rpm) P104 212E
Power (hp)
100
60 80
30 p si]
ar [20 60
40 140 b
40
20
20
0 0
0 500 1000 1500 2000 2500 3000 3500
-1
Speed min (rpm) P104 211E
1.4 6
various displacements.
Greater speeds and lower 1.3 4
inlet pressures are possible 1.2
2
at reduced displacement. 1.1
Operating outside of 1.0 0
(in Hg vac)
Flow (l/min)
100
25
75 20
15
50
10
25
5
0 0
0 500 1000 1500 2000 2500 3000
-1
Speed min (rpm) P104 215E
60 [3 80
Power (hp)
bar
210
psi] 60
2030
40 bar [
140
40
20
20
0 0
0 500 1000 1500 2000 2500 3000
-1
Speed min (rpm) P104 214E
1.4 6
various displacements.
Greater speeds and lower 1.3 4
inlet pressures are possible 1.2
2
at reduced displacement. 1.1
Operating outside of 1.0 0
(in Hg vac)
Flow (l/min)
120
30
80 20
40 10
0 0
0 500 1000 1500 2000 2500
-1
Speed min (rpm) P104 218E
si]
120
0p
80 [3 77
ar
0b 100
26 ]
psi
[3 045
bar
Power (kW)
60
Power (hp)
210 80
i]
0 ps
[203 60
bar
40 140
40
20
20
0 0
0 500 1000 1500 2000 2500
-1
Speed min (rpm) P104 217E
1.4 6
various displacements.
Greater speeds and lower 1.3 4
inlet pressures are possible 1.2
2
at reduced displacement. 1.1
Operating outside of 1.0 0
(in Hg vac)
J K
Order code R S P C D E F G H 1 2 3 1 2 3 L M N
JR L 060B LS 23 20 NN N 3 S1 N2 A2N NNN NNN NNN
R Product
JR J Frame, variable displacement open circuit pump
S Rotation
L Left hand (counterclockwise)
R Right hand (clockwise)
C Control type
PC Pressure compensated control 100-280 bar [1450-4060 psi]
BC* Pressure compensated control 290-310 bar [4205-4495 psi]
RP Remote pressure compensated control 100-280 bar [1450-4060 psi]
BP* Remote pressure compensated control 290-310 bar [4205-4495 psi]
LS Load sensing / pressure compensating control 100-280 bar [1450-4060 psi]
BS* Load sensing / pressure compensating control 290-310 bar [4205-4495 psi]
LB Load sensing / pressure compensating control with internal bleed orifice 100-280 bar [1450-4060 psi]
BB* Load sensing / pressure compensating control with internal bleed orifice 290-310 bar [4205-4495 psi]
AG Pressure compensated control with electric on/off solenoid operated 2-way valve (normally closed)
AF Pressure compensated control with electric on/off solenoid operated 2-way valve (normally open)
* Use only with 45, 51, and 60 cm displacements.
F Not used
NN Not applicable
G Pilot orifice
N None (standard)
H Gain orifice
3 Standard orifice
J K
Order code R S P C D E F G H 1 2 3 1 2 3 L M N
(continued)
J1 Input shaft
C2 13 tooth, 16/32 pitch (ANSI A92.1 1970 - Class 5)
C3 15 tooth, 16/32 pitch (ANSI A92.1 1970 - Class 5)
S1 14 tooth, 12/24 pitch (ANSI A92.1 1970 - Class 5)
K4 31.75 mm [1.25 in] straight key
TO 31.75 mm [1.25 in], 1:8 taper
K1 Shaft seal
A Single lip seal, viton
K3 Not used
N Not applicable
L Displacement limiter
NNN None
FFF * Adjustable, factory set at maximum angle
* can only be used with V and W endcap options
M Special hardware
NNN None
N Special features
NNN None
L2
S L1 P104 220
X Legend
B = Outlet
S = Inlet
B L1, L2 = Case drain
X = Remote PC port
M1
M1* = System pressure gauge port
* M1 port is available on axially ported endcaps
only
Legend
B B = Outlet
S = Inlet
M1
L1, L2 = Case drain
X = LS signal port
M1* = System pressure gauge port
* M1 port is available on axially ported endcaps
L2 only
S L1 P104 223
Legend
B B = Outlet
S = Inlet
M1 L1, L2 = Case drain
X = LS signal port
M1* = System pressure gauge port
* M1 port is available on axially ported endcaps
L2 only
S L1 P104 222
Legend
B = Outlet
B S = Inlet
M1
L1, L2 = Case drain
X = Remote PC port
M1* = System pressure gauge port
* M1 port is available on axially ported endcaps
L2
only
S L1 P106 656E
Legend
B B = Outlet
M1
S = Inlet
L1, L2 = Case drain
X = Remote PC port
M1* = System pressure gauge port
L2
* M1 port is available on axially ported endcaps
S L1 P106 657E only
Evaluate your system to decide if normally open or normally closed control override is
required for failsafe operation.
Input shafts
15.2 0.5
[0.6 0.02]
8 0.8
[0.31 0.03]
33
[1.3]
22.36 0.5
[0.88 0.02]
8 0.8
[0.31 0.03]
38
[1.5]
P104 225E
COUPLING MUST NOT
PROTRUDE BEYOND
THIS POINT
1. See Input shaft torque ratings, page 18 for an explanation of maximum torque.
input shafts
(continued)
31.14 0.08
[1.226 0.003]
28 0.5
[1.1 0.02]
7.94 [0.313]
For use with SAE-C 48.030.43 X 28.56 [1.125] LONG
[1.89]0.02 SQUARE KEY
35.2 0.13
[1.39 0.01]
31.72 0.025
[1.249 0.001]
1. See Input shaft torque ratings, page 18 for an explanation of maximum torque.
input shafts
(continued)
[1.69] +.03
-0.04
7.887 +0.025
-0
For use with SAE-C [0.3105] +0.001
-0
X Dia. 31.8 +0- 0.010
[1.25] +0 -0.25
WOODRUFF KEY
1.00-20 UNF-2A THD
30.1625
22.4 0.3 [1.19]
[0.88 0.01] GAUGE
GAUGE
8 0.8
[0.31 0.03]
1. See Input shaft torque ratings, page 18 for an explanation of maximum torque.
1.95
53.2 [0.08] P104 230E
[2.09] O-RING SEAL REQUIRED
REF 82.22 [3.23] I.D x 8.1
106.4 2.62 [0.103] CROSS SECTION [0.32] A COUPLING-SAE A
[4.19] SPLINE:
P/N 5000373
59.4 9 TOOTH
[2.34] 16/32 PITCH
30 PRESSURE ANGLE
Specifications 14.288 [0.5625] PITCH DIA
FILLET ROOT SIDE FIT
Coupling 9-tooth 11-tooth PER ANSI B92.1-1970 CLASS 6
T COUPLING-SAE A
Spline minimum 13.5 mm [0.53 in] 15 mm [0.59 in] SPLINE:
engagement 11 TOOTH
16/32 PITCH
Maximum torque 107 Nm [950 lbfin] 147 Nm [1300 lbfin] 30 PRESSURE ANGLE
17.463 [0.6875] PITCH DIA
FILLET ROOT SIDE FIT
PER ANSI B92.1-1970 CLASS 6
9.8
[0.39] R2.0 MAX
[0.08]
101.65 +0.08
-0
[4.002 +.003
-0 ]
Displacement limiter J Frame open circuit pumps are Displacement limiter cross-section
available with an optional adjustable
displacement limiter. This adjustable
stop limits the pumps maximum
displacement.
Setting range
J45B 8.4 to 45 cm [0.51 to 2.75 in]
J51B 13.7 to 51 cm [0.84 to 3.11 in]
J60B 16.8 to 60 cm [1.03 to 3.66 in]
J65B 25.4 to 65 cm [1.55 to 3.97 in] P106 727E
J75B 28.4 to 75 cm [1.73 to 4.58 in]
9.7
57.3 [0.38]
[2.26]
127.03 +0.05
-0
114.6 [5.001+.002
-0 ]
[4.51]
131.57
[5.18]
1.3
O-RING SEAL REQUIRED [0.05]
57.3 REF 126.72 [4.989] I.D. x C COUPLING-SAE C P104 232E
[2.26] 1.78 [0.070] CROSS SECTION 14 SPLINE:
P/N 331256 [0.55] 14 TOOTH
114.6 12/24 PITCH
[4.51] 58.0 30 PRESSURE ANGLE
[2.28] 29.633 [1.1667] PITCH DIA
FILLET ROOT SIDE FIT
MIN SHAFT PER ANSI B92.1-1970 CLASS 6
CLEARANCE
Specifications
Coupling 14-tooth
Spline minimum 18.3 mm [0.72 in]
engagement
Maximum torque 339 Nm [3000 lbfin]
MOUNTING
Endcap and shaft machined FLANGE
to accommodate auxiliary
mounting pads; pad and
coupling not included.
Conversion kits are available
for installation in the field.
P104 233E
246.3
[9.7]
BOTH SIDES
LS SIGNAL PORT X
ISO 11926-1
SAE J1926/1
7/16 -20
28.9 83.4
[1.14] [3.28]
BOTH
SIDES
47
73.2 [1.85]
[2.88]
82.1
SYSTEM PRESSURE [3.2]
GAUGE PORT M1
ISO 11926-1 CASE DRAIN PORT L1
SAE J1926/1 ISO 11926-1
9/16 -18 SAE J1976/1
7/8 -14
113.6
[4.5]
APPROXIMATE
CENTER OF 15
GRAVIT Y [0.59]
SYSTEM PORT B
(OUTLET PORT)
ISO 11926-1 R1 MAX
SAE J1926/1 [0.04]
1 5/16 -12
SYSTEM PORTS
(INLET POR T)
ISO 11926-1
SAE J1926/ 1
1 7/8 -12
SYSTEM PORT B 37
(OUTLET PORT) [1.46]
ISO 11926-1
SAE J1926/1
1 5/16 -12
137.1
CASE DRAIN PORT L2 [5.4]
44.5 36.2 ISO 11926-1 P106 172E
[1.8] [1.43] SAE J1926/1
7/8 -14
Third-angle
Counterclockwise rotation, O-ring boss ports projection
mm [in]
LS STANDBY
APPROXIMATE PRESSURE
CENTER OF ADJUSTMENT
0.9 PC PRESSURE 92.7
GRAVIT Y [0.04] ADJUSTMENT [3.65]
11.2 LS SIGNAL
[0.4] PORT X
96.7
[3.81]
146 53.3
[5.75] [2.1]
77.2 LS SIGNAL
73 [3.04]
[2.87] PORT X
ALTERNATE
232.3
[9.15]
93
[3.66]
17.5
[0.69]
2X
90.5
[3.56]
181
[7.13] P104 234E
PC only control Third-angle
SAE-C two-bolt housing
projection
mm [in]
25.4 [1]
OUTLET
SYSTEM PORT B
(OUTLET PORT)
77.77
52.37 345 bar
[3.062] 5000 PSI
[2.062]
SPLIT FLANGE BOSS
PER ISO 6162
50.8 [2] SAE J518
OUTLET (CODE 61)
SYSTEM PORT S with 3/8-16 UNC
(INLET PORT) X 18.61 [0.732] MIN THREAD
207 bar
3000 PSI 42.88
26.19
SPLIT FLANGE BOSS [1.688] [1.031]
PER ISO 6162 44.5
36.2
SAE J518 [1.75]
[1.43]
(CODE 61)
with 1/2-13 UNC
X 27 [1.063] MIN THREAD
50.8 [2]
OUTLET
SYSTEM PORT S
(INLET PORT)
207 bar
3000 PSI
77.77 SPLIT FLANGE BOSS
52.37 [3.062] PER ISO 6162
[2.062] SAE J518
(CODE 61)
25.4 [1] with 1/2-13 UNC
OUTLET X 23 [0.906] MIN THREAD
SYSTEM PORT B
(OUTLET PORT)
345 bar
5000 PSI
SPLIT FLANGE BOSS 26.19 42.88
PER ISO 6162 [1.031] [1.688]
SAE J518 44.5 36.2
(CODE 61) [1.75] [1.43]
with 3/8-16 UNC
X 18.61 [0.732] MIN THREAD P104 235E
47
[1.85]
82.1
[3.23]
CASE DRAIN PORT L1
PER ISO 11976-1
* Interference with internal components will occur SAE J 1976/1
7/8-14
if fitting depth in port X is greater than 11.8 mm [0.465 in]
99.4 239.8
[3.9] [9.44]
44.9 LS SIGNAL PORT X
* LS SIGNAL PORT X [1.77]
200.4
SAE J1926/1 BOTH LS STANDBY
0.4375-20 [7.89]
SIDES PRESSURE
ADJUSTMENT LS SIGNAL PORT X
ALTERNATE 15
PC PRESSURE [0.59]
ADJUSTMENT
116.5 BOTH R1 MAX
[4.59] SIDES [0.04]
50.8 [2]
INLET
76.2 84 SYSTEM PORT S 9.4
[3] [3.31] (INLET PORT) [0.37]
207 BAR [3000 PSI} 194.6
SPLIT FLANGE [7.66]
Counterclockwise rotation PER ISO 6162
SAE J518 242.4
(CODE 61) [9.54]
with 1/2-13 UNC
X 27 [1.063] MIN THREAD DEPTH
SYSTEM SYSTEM
PORT S PORT B
INLET OUTLET 37
[1.46]
137.1
84 76.2 [5.4]
[3.31] [3] CASE DRAIN PORT L2
PER ISO 11926-1
SAE J1926/1
P106 173E
Clockwise rotation 7/8-14
Third-angle
projection
mm [in]
96.7
[3.8]
146
[5.75]
52.37
[2.062]
73 77.2
[2.87] [3.04]
25.4 [1]
SYSTEM PORT B 26.19
[1.031]
SAE-B two-bolt housing (OUTLET PORT)
14.4 345 BAR [5000 PSI] SPLIT FLANGE
[0.567] PER ISO 6162
2X SAE J518 (C ODE 61)
with 3/8-16 UNC X 22 [0.866]
MINIMUM THREAD DEPTH
188.84
[7.43]
240.1
[9.45]
106.62
[4.20]
17.5
[0.69]
2X
90.5
[3.56]
181
PC only control P104 236E [7.13]
Third-angle
SAE-C two-bolt housing projection
mm [in]
139.84
[5.51]
139.84
[5.51]
20 20
Radial endcap with electric on/off right control (clockwise) Radial endcap with electric on/off left control (counterclockwise)
269.0 269.0
83.4 76.9 [10.62]
76.9 83.4 [10.62] [3.28] [3.03]
[3.03] [3.28]
20
20
141
141.0 [5.55]
141.0 [5.55]
[5.55]
Axial endcap with electric on/off right control (counter clockwise) Axial endcap with electric on/off left control (clockwise)
P106 191E
Third-angle
projection
mm [in]
Displacement limiter
endcaps
241.65
[9.5] 207.12 207.12
[8.2]
[8.2] 167.72
167.72
[6.6]
[6.6]
162.54 162.54
[6.4] [6.4]
146.5 146.5
[5.8] [5.8]
241.65
[9.5]
Radial endcap - counterclockwise Axial endcap - counterclockwise
241.65
207.12
[9.5]
207.12 [8.2]
[8.2] 167.72
167.72 [6.6]
[6.6]
162.54 162.54
[6.4] [6.4]
146.5 146.5
[5.8] [5.8]
241.65
[9.5]
Radial endcap - clockwise Axial endcap - clockwise
P106 728E
Third-angle
projection
mm [in]