Drivers handbook
A passion for performance
ELF, partner of
www.lubricants.elf.com
A brand from
Welcome to your new vehicle
This Drivers Handbook contains the information necessary:
for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and
the technical developments it incorporates.
to ensure that it always gives the best performance by following the simple, but comprehensive advice concerning regular main-
tenance.
to enable you to deal quickly with minor faults not requiring specialist attention.
It is well worth taking a few minutes to read this handbook to familiarise yourself with the information and guidelines it contains
about the vehicle and its functions and new features. If certain points are still unclear, our Network technicians will be only too
pleased to provide you with any additional information.
The following symbol will help you when reading this handbook:
The descriptions of the models given in this handbook are based on the technical specifications at the time of writing. This hand-
book covers all items of equipment (both standard and optional) available for these models but whether or not these are
fitted to the vehicle depends on the version, options selected and the country where the vehicle is sold.
This handbook may also contain information about items of equipment to be introduced later in the model year.
Throughout the manual, the approved Dealer is your RENAULT Dealer.
Translated from French. Copying or translation, in part or in full, is forbidden unless prior written permission has been obtained from the vehicle manu-
facturer.
0.1
0.2
C O N T E N T S
Sections
Driving ................................................................... 2
Maintenance ......................................................... 4
0.3
0.4
Section 1: Getting to know your vehicle
1.2
RENAULT CARD: general information (2/3)
Integrated key 5
The integrated key is used to lock or
unlock the front left-hand door if the
RENAULT card does not work:
when the RENAULT card battery is
5 drained, flat battery, etc.
Drivers responsibility
use of devices using the same fre- when parking or stopping
quency as the card; the vehicle
6 vehicle located in a high electromag- Never leave an animal,
netic radiation zone. child or adult who is not self-suffi-
cient alone on your vehicle, even for
Access to key 5 a short time.
Press button 6 and pull on key 5 then They may pose a risk to themselves
release the button. or to others by starting the engine,
RENAULT card operating activating equipment such as the
range Using the key
electric windows or locking the
This varies according to the surroun- Please refer to the information on doors.
dings: when handling the RENAULT Locking and unlocking the opening
Also, in hot and/or sunny weather,
card, it is important to make sure that elements.
please remember that the tempera-
you do not lock or unlock the doors by Once you have accessed the vehicle ture inside the passenger compart-
inadvertently pressing the buttons. using the integrated key, replace it ment increases very quickly.
in its housing in the RENAULT card,
RISK OF DEATH OR SERIOUS
then insert the RENAULT card into
INJURY.
the card reader to start the vehicle.
1.3
RENAULT CARD: general information (3/3)
Drivers responsibility
when parking or stopping
the vehicle
Never leave an animal,
child or adult who is not self-suffi-
cient alone on your vehicle, even for
a short time.
They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or locking the
Replacement: need for an doors.
additional RENAULT Card Also, in hot and/or sunny weather,
If you lose your RENAULT card or please remember that the tempera-
require another, you can obtain one ture inside the passenger compart-
from an authorised dealer. ment increases very quickly.
If a RENAULT card is replaced, it RISK OF DEATH OR SERIOUS
Advice INJURY.
will be necessary to take the vehi-
Avoid leaving the card in hot, cold or cle and all of its RENAULT cards to
humid areas. an approved Dealer to initialise the
Do not keep the RENAULT card in system.
a place where it could be bent or You may use up to four RENAULT
damaged accidentally, such as in a cards per vehicle.
back pocket of a garment.
1.4
REMOTE CONTROL RENAULT CARD: use
Locking the doors and Unlocking/locking the
luggage compartment luggage compartment only
2 3 Press the locking button 2. The hazard Press button 4 to unlock/lock the lug-
warning lights flash twice to indicate gage compartment.
that the doors have locked. If a door
or the luggage compartment is open
1 4 or not properly shut, or if a RENAULT RENAULT card not detected
card is still in the reader, the doors and alarm
luggage compartment lock then quickly If you open a door while the engine
unlock and the hazard warning lights is running and the card is not in the
do not flash. reader, the message Keycard not de-
tected and a beep will warn you. The
warning disappears when the card is in-
serted in the reader again.
If the vehicle has been unlocked
Unlocking the doors and but neither the doors or tailgate are
open, it locks again automatically
Distance lighting function
tailgate after two minutes.
The interior lights come on for approxi-
mately 30 seconds when button 3 is
Press button 1. pressed. This can be used, for exam-
The hazard warning lights flash once ple, to identify the vehicle from a dis-
to indicate that the doors have been un- tance when parked in a car park.
locked. Note: pressing button 3 again switches
off the lighting.
The card buttons are deactivated
when the engine is running.
The flashing status of the hazard
warning lights informs you of the ve-
hicle status:
one flash indicates that the vehi-
cle is completely unlocked;
two flashes indicate that the ve-
hicle is completely locked.
1.5
HANDS-FREE RENAULT CARD: use (1/4)
4
3
1
1.6
HANDS-FREE RENAULT CARD: use (2/4)
Drivers responsibility
when parking or stopping
the vehicle
Never leave an animal,
3 child or adult who is not self-suffi-
1 cient alone on your vehicle, even for
a short time.
They may pose a risk to themselves
or to others by starting the engine,
Locking the vehicle The hazard warning lights flash twice
activating equipment such as the
and a beep sounds to indicate that the
There are three ways to lock the vehi- electric windows or locking the
doors have locked.
cle: remotely, using button 3, or using doors.
the RENAULT card. The beep may be switched off. Please
Also, in hot and/or sunny weather,
contact an authorised dealer.
please remember that the tempera-
Remote locking If an opening element (door or boot) is ture inside the passenger compart-
With the RENAULT card on you, and open or not properly closed, or a card is ment increases very quickly.
doors and tailgate closed, move away in the passenger compartment (or the
RISK OF DEATH OR SERIOUS
from the vehicle: it will lock automati- card reader), the vehicle will not lock. In
INJURY.
cally once you have left zone 1. this situation, no beep sounds and the
Note: the distance at which the vehicle hazard warning lights do not flash.
locks depends on the surroundings.
1.7
HANDS-FREE RENAULT CARD: use (3/4)
1.8
HANDS-FREE RENAULT CARD: use (4/4)
Hands-free RENAULT card non-
detection alarm
With the engine running, if you open
and close a door and the card is no
longer within range 6, the message
Keycard not detected and a beep
warns you of this. Drivers responsibility
The warning disappears when the card when parking or stopping
6 is again within range 6. the vehicle
Never leave an animal,
child or adult who is not self-suffi-
cient alone on your vehicle, even for
a short time.
They may pose a risk to themselves
or to others by starting the engine,
Special features
activating equipment such as the
The vehicle will not lock if: electric windows or locking the
a door or the tailgate is open or not doors.
properly closed; Also, in hot and/or sunny weather,
a card is still in zone 6 (or in the card please remember that the tempera-
reader) and no other card is in the ture inside the passenger compart-
external detection zone. ment increases very quickly.
RISK OF DEATH OR SERIOUS
INJURY.
1.9
RENAULT CARD: deadlocking
1 2
1.10
OPENING AND CLOSING THE DOORS (1/2)
Card reminder buzzer
On opening the drivers door, if the
card is still in the reader, the message
PLEASE REMOVE KEYCARD is dis-
played on the instrument panel accom-
1 4 panied by a warning beep.
As a safety precaution,
the doors should only be
opened or closed when the
vehicle is stationary.
1.11
OPENING AND CLOSING THE DOORS (2/2)
Drivers responsibility
when parking or stopping
the vehicle
5 Never leave an animal,
child or adult who is not self-suffi-
cient alone on your vehicle, even for
a short time.
They may pose a risk to themselves
Child safety or to others by starting the engine,
activating equipment such as the
To make it impossible for the rear doors
electric windows or locking the
to be opened from the inside, move
doors.
lever 5 on each door and check from
Also, in hot and/or sunny weather,
the inside that the doors are securely
please remember that the tempera-
locked.
ture inside the passenger compart-
ment increases very quickly.
RISK OF DEATH OR SERIOUS
INJURY.
1.12
LOCKING/UNLOCKING THE DOORS (1/2)
Locking/Unlocking the doors
from the outside
This is done using the RENAULT Card;
see the RENAULT Card information in 2
Section 1.
In certain cases, the RENAULT card 1
may not work:
if the RENAULT card battery is weak,
flat, etc.
if equipment operating on the same
frequency as the card (mobile
phones, etc.) is used;
vehicle located in a high electromag-
netic radiation zone.
Using the key integrated in Locking the doors manually
It is then possible:
the RENAULT card Turn screw 2 with the door open (using
to use the key integrated into the the end of the key) and close the door.
Insert key 1 into the lock in the drivers
card to unlock the front left-hand
door and lock or unlock. This means that the doors are then
door;
locked from the outside.
to lock each of the doors manually;
The doors may then only be opened
to use the interior door locking/un- from the inside or by using the key in
locking control (refer to the following the front left-hand door.
pages).
1.13
LOCKING/UNLOCKING THE DOORS (2/2)
Locking the doors without Door and tailgate status
the RENAULT card indicator
3 For example, in the event of a dis- With the ignition on, the warning light
charged battery or the RENAULT card integrated in switch 3 informs you of the
temporarily not working, etc. locking status of the opening elements:
With the engine switched off and indicator light on, the doors and tail-
an opening element (door or boot) gate are locked,
open, press and hold switch 3 for more indicator light off, the doors and tail-
than five seconds. gate are unlocked.
When the door is closed, all the doors When you lock the doors, the indicator
and the tailgate will be locked. light remains lit and then goes out.
Unlocking the vehicle from the outside
is only possible with the RENAULT card
in the vehicle's access zone or using
Interior locking/unlocking the key integrated in the RENAULT
door control card.
Switch 3 controls the doors, boot and,
depending on the vehicle, the fuel filler Never leave your vehicle
flap simultaneously. with the RENAULT card
If a door or the tailgate is open or not inside.
closed properly, the doors and tailgate
lock/unlock quickly.
If you need to transport objects with the After locking/unlocking the vehicle
boot open, the other opening elements or the luggage compartment only Drivers responsibility
can still be locked: with the engine using the buttons on the RENAULT If you decide to keep the
stopped, press switch 3 for more than card, remote locking and unlocking doors locked when you are
five seconds to lock the other opening in hands-free mode are deactivated. driving, remember that it
elements. may be more difficult for those as-
To reactivate the hands-free mode:
restart the vehicle. sisting you to gain access to the
passenger compartment in the
event of an emergency.
1.14
RENAULT ANTI-INTRUDER DEVICE (RAID)
Activating/deactivating the
function
1 With the engine running, press the
button 1 for approximately 5 seconds,
until you hear a warning beep.
Operating faults
If you experience an operating fault
(no automatic locking, the indicator
light incorporated in button 1 does not
light up when trying to lock the open-
ing elements, etc.), firstly check that the
opening elements are properly closed.
If they are properly closed, contact an
Operating principle authorised dealer.
After the vehicle is started, the system
automatically locks the doors when
you are driving at approximately 6 mph
(10 km/h) and over.
The door can be unlocked:
by pressing the button 1 to unlock
the doors;
by opening a front door (vehicle sta-
tionary). Drivers responsibility
1.15
FRONT HEADRESTS
To raise the headrest
Raise the headrest to its highest po-
sition (tilt the seatback backwards if
A necessary). Press button 1 and lift the
2
headrest to release it.
1
To refit the headrest
Insert the headrest rods into the holes
(tilt the seatback backwards if neces-
sary). Lower the headrest until it locks
and press button 1 to adjust to the de-
sired height. Check that each rod 2 on
the seatback is securely locked.
1.16
FRONT SEATS
2
4
3
1
1.17
SEAT BELTS (1/3)
Always wear your seat belt when trav- Before starting, first adjust your driv-
elling in your vehicle. You must also ing position, then ask all occupants
comply with the legislation of the par- to adjust their seat belts to ensure
ticular country you are in. optimum protection.
1.18
SEAT BELTS (2/3)
Front seat belt reminder
warning light
This lights up on the central display
when the engine is started then, if the
drivers or front passengers seat belt
(if this seat is occupied) is not fastened
and the vehicle has reached approxi- 6
1 mately 12 mph (20 km/h), it flashes and
a bleep sounds for around 2 minutes.
Note: an object placed on the passen-
ger seat base may activate the warning
3 light in some cases.
4 Rear seat belt reminder (depending
5 5 on vehicle)
Locking
The warning light comes on on
the central display, accompanied by a Adjusting the height of the
Unwind the belt slowly and smoothly message on the instrument panel, indi- front seat belts
and ensure that buckle 3 locks into cating the number of seat belts buckled Press button 6 to adjust the seat belt
catch 5 (check that it is locked by pull- for approximately 30 seconds each: height so that shoulder strap 1 is worn
ing on buckle 3). the vehicle is started; as shown previously. Press button 6
a door is opened; and raise or lower the seat belt. Make
If the belt jams, allow it to return slightly
a rear seat belt is fastened or unfas- sure that the seat belt is locked in posi-
before attempting to unwind it again.
tened. tion correctly after you have adjusted it.
If your seat belt is completely jammed,
Check that the rear passengers are
pull slowly, but firmly, so that just over
wearing seat belts and that the number Unlocking
3 cm unwinds. Allow it to return slightly
of seat belt shown as fastened corre-
before attempting to unwind it again. Press button 4 and the seat belt will be
sponds to the number of rear bench
If there is still a problem, contact an ap- seat places occupied. rewound by the inertia reel. Guide the
proved dealer. belt.
1.19
SEAT BELTS (3/3)
The following information applies to the vehicles front and rear seat belts.
1.20
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/4)
Depending on the vehicle, they will con-
sist of: Have the entire restraint
system checked following
front seat belt inertia reel preten- an accident.
sioners;
No operation whatso-
chest-level load limiters; ever is permitted on any part of
air bags for driver and front pas- the system (pretensioners, air
senger. bags, computers, wiring) and the
system components must not
These systems are designed to act in- be reused on any other vehicle,
dependently or together when the vehi- even if identical.
cle is subjected to a frontal impact.
To avoid incorrect triggering of
Depending on the severity of the the system which may cause
impact, the system can trigger: injury, only qualified personnel
1
seat belt locking; from an approved Dealer may
work on the pretensioner and air
the seat belt inertia reel pretensioner Pretensioners bag system.
(which engages to correct seat belt
slack); The pretensioners hold the seat belt The electric trigger system may
against the body, holding the occupant only be tested by a specially
airbags. more securely against the seat, thus in- trained technician using special
creasing the seat belts efficiency. equipment.
With the ignition on, following a signif- When the vehicle is scrapped,
icant frontal impact and depending on contact an approved Dealer for
the severity of the impact, the system disposal of the pretensioner and
may trigger the seat belt inertia reel air bag gas generators.
pretensioner 1, which instantly retracts
the seat belt.
1.21
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/4)
Load limiter Airbags for driver and front
Above a certain severity of impact, this passenger
mechanism is used to limit the force of Fitted to the driver and passenger side.
the belt against the body so that it is at A
an acceptable level. The presence of this equipment is in-
dicated by the word Air bag on the
steering wheel and dashboard (air bag
zone A) and, depending on the vehicle,
a symbol on the lower section of the
windscreen.
Each air bag system consists of:
an air bag and gas generator fitted
on the steering wheel for the driver
and in the dashboard for the front
passenger;
an electronic unit for system monitor-
ing which controls the gas generator
electrical trigger system;
1.22
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/4)
1.23
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/4)
All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent
the risk of serious injuries caused by items which may be dislodged when the air bag inflates.
1.24
METHODS OF RESTRAINT IN ADDITION TO THE REAR SIDE SEAT BELTS
Force limiter
Above a certain severity of impact, this
mechanism is used to limit the force of
the belt against the body so that it is at
an acceptable level.
1.25
SIDE PROTECTION DEVICES
Side Airbags
This airbag may be fitted to each of the
front seats and is activated at the sides
of the seats (door side) to protect the
occupants in the event of a severe side
impact.
1.26
ADDITIONAL METHODS OF RESTRAINT
All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent
the risk of serious injuries caused by items which may be dislodged when it inflates.
The airbag is designed to complement the action of the seat belt. Both the air bags and seat belts are integral parts of
the same protection system. It is therefore essential to wear seat belts at all times. If seat belts are not worn, the oc-
cupants are exposed to the risk of serious injury in the event of an accident. It may also increase the risk of minor su-
perficial injuries occurring when the airbag is deployed, although such minor injuries are always possible with air bags.
If the vehicle should overturn or in the event of a rear impact, however severe, the pretensioners and airbags are not always
triggered. Impacts to the underside of the vehicle, e.g. from pavements, potholes or stones, can all trigger these systems.
No work or modification whatsoever may be carried out on any part of the airbag system (airbags, pretensioners, computer,
wiring harness, etc.), except by qualified Network personnel.
To ensure that the system is in good working order and to avoid accidental triggering of the system which may cause injury,
only qualified Network personnel may work on the airbag system.
As a safety precaution, have the airbag system checked if your vehicle has been involved in an accident, or is stolen or
broken into.
When selling or lending the vehicle, inform the user of these points and hand over this handbook with the vehicle.
When scrapping your vehicle, contact your approved Dealer for disposal of the gas generator(s).
1.27
CHILD SAFETY: General information (1/2)
Carrying children
Children, and adults, must be correctly
seated and strapped in for all journeys.
The children being carried in your vehi-
cle are your responsibility.
A child is not a miniature adult. Children
are at risk of specific injuries as their
muscles and bones have not yet fin- Drivers responsibility
ished growing. The seat belt alone when parking or stopping
would not provide suitable protection. the vehicle
Use an approved child seat and ensure
Never leave an animal,
you use it correctly.
child or adult who is not self-suffi-
cient alone on your vehicle, even for
a short time.
They may pose a risk to themselves
or to others by starting the engine,
A collision at 30 mph activating equipment such as the
(50 km/h) is the same as fall- electric windows or by locking the
ing a distance of 10 metres. doors.
Transporting a child without Also, in hot and/or sunny weather,
a restraint is the equivalent of allow- please remember that the tempera-
ing him or her to play on a fourth- ture inside the passenger compart-
floor balcony without railings. ment increases very quickly.
Never travel with a child held in your
arms. In the event of an accident, RISK OF DEATH OR SERIOUS
you will not be able to keep hold of INJURY.
To prevent the doors being the child, even if you yourself are
opened, use the Child wearing a seat belt.
safety device (refer to the If your vehicle has been involved in
information on Opening a road accident, replace the child
and closing the doors in Section 1). seat and have the seat belts and
ISOFIX anchorage points checked.
1.28
CHILD SAFETY: General information (2/2)
Using a child seat
The level of protection offered by the Set a good example by always fas-
child seat depends on its ability to re- tening your seat belt and teaching
strain your child and on its installation. your child:
Incorrect installation compromises the to strap themselves in correctly;
protection it offers the child in the event to always get in and out of the car
of harsh braking or an impact. at the kerb, away from busy traf-
fic.
Before purchasing a child seat, check
that it complies with the regulations for Do not use a second-hand child
the country you are in and that it can seat or one without an instruction
be fitted in your vehicle. Consult an ap- manual.
proved dealer to find out which seats Check that there are no objects in
are recommended for your vehicle. the vicinity of the child seat which
Before fitting a child seat, read the could impede its operation.
manual and respect its instructions. If
you experience any difficulties during
Never leave a child unat-
installation, contact the manufacturer
tended in the vehicle.
of the equipment. Keep the instructions
with the seat. Check that your child is
always strapped in and that
the belt or safety harness used is
correctly set and adjusted. Avoid
wearing bulky clothing which could
cause the belts to slacken.
Never let your child put their head or
arms out of the window.
Check that the child is in the correct
position for the entire journey, espe-
cially if asleep.
1.29
CHILD SAFETY: choosing a child seat
1.30
CHILD SAFETY: choosing a child/baby seat mounting (1/2)
There are two ways of attaching child Attachment using the ISOFIX
seats: via the seat belt or using the Before using an ISOFIX system
ISOFIX system. child seat that you pur-
chased for another vehicle, Authorised ISOFIX child seats are ap-
Attachment via the seat belt check that its installation is proved in accordance with regulation
The seat belt must be adjusted to authorised. Consult the list of ve- ECE-R44 in one of the three following
ensure that it is effective in the event of hicles which can be fitted with the cases:
harsh braking or an impact. seat from the equipment manufac- ISOFIXuniversal 3-point forward-fac-
Ensure that the strap paths indicated turer. ing seat;
by the child seat manufacturer are re- ISOFIXsemi-universal 2-point seat;
spected. specific.
Always check that the seat belt is cor- For the latter two, check that your child
rectly fastened by pulling it up, then seat can be installed by consulting the
pulling it out fully whilst pressing on the list of compatible vehicles.
child seat. Attach the child seat with the ISOFIX
Check that the seat is correctly held by locks, if these are provided. The ISOFIX
moving it from side to side and back system allows quick, easy, safe fitting.
to front: the seat should remain firmly
fixed. The seat belt must never The ISOFIX system consists of 2 rings
Check that the child seat has not been be twisted or the tension and, in some cases, a third ring.
installed at an angle and that it is not relieved. Never pass the
resting against a window. shoulder strap under the
arm or behind the back.
Check that the seat belt has not
been damaged by sharp edges.
If the seat belt does not operate nor-
mally, it will not protect the child.
Do not use the child seat
Consult an approved dealer. Do not
if it may unfasten the seat
use this seat until the seat belt has
belt restraining it: the base
been repaired. No modifications may be
of the seat must not rest on
the buckle and/or catch of the seat made to the component
belt. parts of the restraint system
(seat belts, ISOFIX and
seats and their mountings) originally
fitted.
1.31
CHILD SAFETY: choosing a child/baby seat mounting (2/2)
3
2
5
4
The two rings 1 are located between Rear seats Front passenger seat
the seatback and the seat base and are Put the rear parcel shelf down in order Attach the belt hook 3 to the ring 5.
identified by a marking. Use the access to be able to pass the strap 3 between
guides 2 of the child seat to ease it into the seatback and the parcel shelf (see All seats
place and lock it into the rings 1. the information on Rear parcel shelf in Pull the belt 3 so that the back of the
The third ring 4 or 5 is used to attach Section 3). Fix the hook on the ring 4, child seat comes into contact with the
the upper strap on some child seats. identified by the symbol on the back of the vehicle seat.
back of the seat in question and located
under the mobile floor.
1.32
CHILD SAFETY: fitting a child seat (1/4)
Some seats are not suitable for fitting In the front seat After installing the child seat, if neces-
child seats. The diagram on the follow- The laws concerning children travel- sary, the seat may be advanced (so as
ing page shows you how to attach a ling in the front passenger seat differ in to leave enough space in the rear seats
child seat. every country. Consult the legislation in for passengers or other child seats).
The types of child seat indicated may force and follow the indications on the For a rear-facing child seat, do not let
not be available. Before using a differ- diagram on the following page. it touch the dashboard or move it to the
ent child seat, check with the manufac- furthest forward position.
Before fitting a child seat in this seat (if
turer that it can be fitted. authorised): Do not change other settings after in-
stalling the child seat.
lower the seat belt as far as possible;
move the seat as far back as possi-
ble;
Ensure that the child seat
or the childs feet do not gently tilt the seatback away from
prevent the front seat from vertical (approximately 25);
locking correctly. Refer to on equipped vehicles, raise the seat
the information on the Front seat base as far as possible.
in Section 1.
Check that when installing the child In all situations, reinsert the headrest to
seat in the vehicle it is not at risk of its full extent so that it does not interfere
coming loose from its base. with the child seat (see the information
If you have to remove the headrest, on Front headrests in Section 1);
check that it is correctly stored so
that it does not come loose under RISK OF DEATH OR
harsh braking or impact. SERIOUS INJURY: Before
Always attach the child seat to the installing a child seat on the
vehicle even if it is not in use so that front passenger seat, check
it does not come loose under harsh that the airbag has been deacti-
braking or impact. vated (please refer to Child safety:
front passenger airbag deactivation
and activation in Section 1).
1.33
CHILD SAFETY: fitting a child seat (2/4)
In the rear side seat
A carrycot can be installed across the
vehicle and will take up at least two
seats.
Position the child with their feet nearest
the door.
Move the front seat as far forward as
possible to install a rear-facing child
seat, then move back the seat in front
as far as it will go, although without al-
lowing it to come into contact with the
child seat.
For the safety of the child in the for-
ward-facing seat, do not move the seat
in front back past the middle of the
runner, do not tilt the seatback too far
(maximum of 25) and raise the seat as
much as possible.
In all situations, remove the rear head-
rests (refer to the information on the
Fit the child seat in a rear
Rear headrests in Section 3). This
seat wherever possible.
must be done before fitting the child
Fitting a seat ISOFIX in
seat.
the rear-left seat means
Check that the forward-facing child seat the middle seat cannot be used.
is resting against the back of the vehi- The central seat belt will no longer
cle seat. be either accessible or useable. To
install an ISOFIX seat in this seat,
detach the central seat belt by hand
before engaging the bolts.
1.34
CHILD SAFETY: fitting a child seat (3/4)
Fitting diagram Child seat attached using the ISOFIX
mounting
1.35
CHILD SAFETY: fitting a child seat (4/4)
The table below summarises the information already shown on the diagram on the previous page, to ensure the regula-
tions in force are respected.
(5) RISK OF DEATH OR SERIOUS INJURY: before installing a child seat on the front passenger seat, check that the
air bag has been deactivated (refer to Child safety: front passenger air bag deactivation/activation Section 1).
1.36
CHILD SAFETY: deactivating/activating the front passenger air bag (1/3)
1.37
CHILD SAFETY: deactivating/activating the front passenger air bag (2/3)
A
3
1.38
CHILD SAFETY: deactivating/activating the front passenger air bag (3/3)
Operating faults
It is forbidden to fit a rear-facing child
seat to the front passenger seat if the
1 airbags activation/deactivation system
is faulty.
Allowing any other passenger to sit in
that seat is not recommended.
Contact your approved dealer as soon
as possible.
2
1.39
DRIVING POSITION: LEFT-HAND DRIVE (1/2)
1 2 3 4 5 6 7 8 9 10 11 7 12 13 1
25
14
24 23 22 21
15
20 16
19 17
18
1.40
DRIVING POSITION: LEFT-HAND DRIVE (2/2)
The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY.
19 Handbrake.
1.41
DRIVING POSITION: RIGHT-HAND DRIVE (1/2)
1 2 3 4 5 6 7 8 4 9 10 11 12 13 1
14
24 17 16 15
23
22
25
21
18
20
19
1.42
DRIVING POSITION: RIGHT-HAND DRIVE (2/2)
The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY.
1 Side air vent. 11 Driver Airbag and horn location. 16 Control for adjusting steering
wheel height and reach.
2 Passenger Airbag location. 12 Multimedia system voice control
button. 17 Engine start/stop button.
3 Heating or air conditioning con-
trols. 13 Stalk: 18 Handbrake.
windscreen and rear screen
4 Centre air vents. wash/wipe; 19 Activation/deactivation control for
trip computer and warning ECO mode.
5 Multimedia touch screen. system information readout.
20 Cruise control/speed limiter con-
6 Hazard warning lights switch. 14 Controls for: trol.
electric headlight beam adjust-
7 Door electric locking switch. ment, 21 Gear lever.
1.43
WARNING LIGHTS (1/5)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
1
k tale as possible.
Low fuel level warning light
g Front fog light tell-tale
M This lights up when the ignition
is switched on and goes out after a few
Rear fog light telltale
f seconds.
If it lights up when driving, fill up with
Left-hand direction indicator fuel as soon as possible. There is only
Instrument panel A: lights up when the
ignition is switched on.
c tell-tale approximately 30 miles (50 km) worth
of fuel left.
Right-hand direction indica-
With the lights on, you can adjust the
brightness by turning the knob 1.
b tor tell-tale
1.44
WARNING LIGHTS (2/5)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
1.45
WARNING LIGHTS (3/5)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
1.46
WARNING LIGHTS (4/5)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
Unavailability of engine
standby warning light
Please see information in the para-
graph on Stop and Start Function in
Section 2.
ECO mode warning light
Preheating warning light
(diesel version)
This comes on when ECO
mode is activated.
This should come on when the igni-
tion is switched on. It indicates that the Please refer to the information on Eco-
heater plugs are in operation. driving in Section 2.
It goes out when preheating is com-
plete. The engine can be started. 2 Door(s) open warning light
1.47
WARNING LIGHTS (5/5)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
1.48
DISPLAYS AND INDICATORS (1/2)
1
4
3
Rev counter 1 Driving style indicator 3 Low engine oil level warning
(graduations x 1000) Please refer to the information on Eco- When the engine is started, display 2
driving in Section 2. alerts the driver when the oil level is at
its minimum. Refer to the information
on the Engine oil level in Section 4.
1.49
DISPLAYS AND INDICATORS (2/2)
To return to the previous mode, repeat
5 the same operation.
6
Note: once the battery is switched off,
6 the trip computer and warning system
8 automatically returns to the original unit
of measurement.
9
7
1.50
ON-BOARD COMPUTER: general information (1/2)
f) distance travelled;
1 g) average speed;
h) distance before service;
service counter;
oil change counter;
2 i) Reset the tyre pressure
j) cruise control/speed limiter pro-
grammed speed;
k) clock and temperature;
l) trip log, operating faults and informa-
tion message readout.
1.51
ON-BOARD COMPUTER: general information (2/2)
Interpreting some of the Automatic resetting of the
values displayed after journey parameters
resetting Resetting occurs automatically when
The values showing average fuel con- the maximum value of any of the pa-
2 sumption, range and average speed rameters is exceeded.
will become more stable and reliable
the further you travel after pressing the
reset button.
For the first few miles after pressing
the reset key you will notice that the
range increases as you travel. This
range takes into account the average
3 fuel consumption since the last time the
reset button was pressed. Therefore,
the average fuel consumption may de-
Resetting the trip mileage crease when:
With trip mileage recorder selected on the vehicle stops accelerating;
the display, press button 2 or 3 until the
mileage recorder resets to zero. the engine reaches its operating
temperature (if the engine was cold
when the reset key was pressed);
Resetting the journey when driving from an urban area
parameters (reset button) onto the open road.
With one of the trip parameters selected
as the display, press and hold button 2
or 3 until the display resets.
1.52
TRIP COMPUTER: trip settings (1/5)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
101778 km
112.4 km a) Total mileage and trip mileage recorder.
FUEL USED
b) Journey parameters.
8L Fuel used.
Fuel consumed since the last reset.
AVERAGE
c) Average fuel consumption since the last reset.
5.8 L/100 The value is displayed after having travelled at least 400 metres since the last
reset.
CURRENT
7.4 L/100 d) Current fuel consumption.
This value is displayed after a speed of approximately 20 mph (30 km/h) is reached.
1.53
TRIP COMPUTER: trip settings (2/5)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
RANGE
541 km e) Estimated range with remaining fuel.
The value is displayed after driving 400 metres.
DISTANCE
522 km f) Distance travelled since last reset.
AVERAGE
123.4 km/H g) Average speed since the last reset.
The value is displayed after driving 400 metres.
1.54
TRIP COMPUTER: trip settings (3/5)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
Examples of selections
On-board computer with mileage- Interpreting the display selected
before-service message
h) Mileage before service or oil change.
Resetting: to reset the distance before service, press and hold button 2 or 3 for approximately 10 seconds until the display
shows the service mileage without flashing.
NB: if a service is performed without changing the engine oil, only the mileage before the next service should be reset. In the
event of an oil change, both the distance before the next service and the next oil change should be reset.
1.55
TRIP COMPUTER: trip settings (4/5)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
Examples of selections
On-board computer with distance before Interpreting the display selected
next service message (cntd.)
h) Mileage before service or oil change.
Mileage before service
SERVICE Oil change in With the ignition switched on and the engine not running,
INTERVALS 30 000 Kms / 24 MO when the message SERVICE INTERVALS is displayed, press
button 2 or 3 for around 5 seconds to display the mileage before
the next service, then briefly press button 2 or 3 to view the
mileage before the next oil change (distance or time remaining
Service due in before the next service). When the range approaches its limit,
there are several possible scenarios:
300 Kms / 24 DAYS
distance/time remaining less than 900 miles (1,500 km) or
one month: the message Service due in is displayed, ac-
companied by the nearest term (distance or time);
range equal to 0 km/miles or service date reached: the
Service required message Service required is displayed accompanied by
warning light .
The vehicle requires an oil change as soon as possible.
Depending on the vehicle, the mileage before an oil change varies according to the driving style (frequent driving at low speed,
door-to-door journeys, extensive use at idling speed, towing a trailer, etc.). The distance remaining until the next oil change can
therefore decrease more quickly in some cases than the actual distance travelled.
Resetting: to reset the mileage before the next service, press and hold button 2 or 3 for approximately 10 seconds until the
display shows the mileage before service without flashing.
NB: if a service is performed without changing the engine oil, only the mileage before the next service should be reset. In the
event of an oil change, both the distance before the next service and the next oil change should be reset.
1.56
TRIP COMPUTER: trip settings (5/5)
l) Trip log.
NO MESSAGE
MEMORISED Successive display:
information messages (passenger airbag OFF etc.);
operating fault messages (Check injection system,
etc.).
1.57
TRIP COMPUTER AND WARNING SYSTEM: information messages
These can help in the vehicle starting phase, or give information about a selection or a driving status.
Examples of information messages are given in the following pages.
PARKING BRAKE ON Indicates that the parking brake has been applied.
PLEASE REMOVE
Request to remove the RENAULT card from the reader when you leave the vehicle.
KEYCARD
TRACTION
Indicates that you have deactivated the traction control function.
CONTROL OFF
TURN STEERINGWHEEL Turn the steering wheel slightly whilst pressing the vehicle start button to unlock the steering
+ START column.
STEERING WHEEL
Indicates that the steering column has not been locked.
NOT LOCKED
1.58
TRIP COMPUTER AND WARNING SYSTEM: operating fault messages
These appear with the warning light and mean that you should drive very carefully to an authorised dealer as
soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle.
They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The
warning light stays on. Examples of operating fault messages are given in the following pages.
CLEAN DIESEL FILTER Indicates the presence of water in the diesel filter; contact an approved Dealer
as soon as possible.
CHECK VEHICLE Indicates a fault in one of the pedal sensors, battery management system or oil
level sensor.
CHECK AIRBAG Indicates a fault in the restraint system in addition to the seat belts. In the event
of an accident, it is possible that they may not be triggered.
CHECK ANTI-POLLUTION SYSTEM Indicates a fault in the vehicles particle filter system.
1.59
TRIP COMPUTER AND WARNING SYSTEM: warning message
These appear with the warning light and require you to stop immediately, for your own safety, as soon as traf-
fic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer.
Examples of warning messages are given in the following pages. Note: the messages appear on the display either individually
or alternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.
ENGINE FAILURE HAZARD Indicates an injection fault, the vehicles engine has overheated or there is a
serious engine fault.
BATTERY CHARGING FAULT Indicates a fault in the vehicle battery charging circuit (alternator etc.).
1.60
STEERING WHEEL/POWER-ASSISTED STEERING
Power Assisted Steering
Never drive with an inadequately
charged battery.
1.61
CLOCK AND EXTERIOR TEMPERATURE (1/2)
A 1
1 3
9C 12:00
2
4
1.62
CLOCK AND EXTERIOR TEMPERATURE (2/2)
External temperature
indicator
Special note:
When the exterior temperature is - 3C
to + 3C, the C characters flash (si-
gnalling a risk of ice on the road).
B
If the power supply is cut (battery disconnected, supply wire cut, etc.), the clock
must be reset.
We recommend that you do not adjust these settings while driving.
1.63
REAR VIEW MIRRORS
Heated door mirrors
With the engine running, mirror de-
icing is activated simultaneously with
A B rear screen de-icing/demisting.
C
D Folding door mirrors
(depending on vehicle)
Move button 1 to position F: the door
E mirrors fold away. To reset them for
driving, return to position C, D or E.
If you manually fold the door mirrors,
F before setting them to the driving posi-
1 tion (C, D, E), you must position con- 2
trol 1 to F.
1.64
EXTERIOR LIGHTING AND SIGNALS (1/3)
Dipped beam
k headlights
1 2 3 Manual operation
Turn the ring 2 until the symbol is oppo-
1 site mark 3. This indicator light on the
instrument panel comes on.
Automatic operation
(depending on vehicle)
Turn ring 2 until the AUTO symbol is op-
posite mark 3: with the engine running,
the dipped beam headlights switch on
or off automatically depending on the
brightness of the light outside, without
any action on stalk 1.
Side lights Daytime running lights
Turn the ring 2 until the symbol function
is opposite mark 3. The daytime running lights come on
An indicator light on the instrument automatically with no action on stalk 1
panel will come on. when the engine is started, and they go
off once the engine is switched off.
1.65
EXTERIOR LIGHTING AND SIGNALS (2/3)
Switching off the lights Front fog lights
There are two possibilities:
g Turn the centre ring 4 on the
1 2 4 5 manually, move ring 2 to position 0; stalk 1 until the symbol is opposite
the lights will go out automatically mark 5, then release it.
when the engine is switched off, the Operation of the fog lights depends on
drivers door is opened or the vehicle the exterior lighting position selected,
is locked. In this case, the next time and an indicator light will light up on the
the engine is started, the lights will instrument panel.
be switched back on according to the
position of the ring 2, taking into ac-
count the exterior light level, without Cornering lights function
moving the stalk 1.
Whenever the dipped beam headlights
are on and under certain conditions (at
Lights-on reminder buzzer speed, the steering wheel at an angle,
in forward gear, the indicator lights on,
A warning beep sounds when the driv-
Main beam headlights etc.), when taking a corner one of the
With the engine running and
ers door is opened to warn you that the
lights are still on.
front fog lights will come on to light the
inside of the bend.
the dipped beam headlights on, push
stalk 1. This indicator light on the instru-
ment panel comes on.
To return to the dipped headlight posi-
tion, pull stalk 1 towards you again.
1.66
EXTERIOR LIGHTING AND SIGNALS (3/3)
Turning off the fog lights
There are two possibilities:
4 5 manually, depending on the vehi-
1 cle, turn the ring 4 again to bring the
mark 5 opposite the symbol for the
fog light that you want to switch off,
or bring the ring 4 into position 0. The
corresponding indicator light will go
out on the instrument panel;
the lights will go out automati-
cally when the engine is switched
off or the vehicle is locked, and the
fog lights when the drivers door is
opened.
The front and rear fog lights switch off
Rear fog light when the exterior lights are switched
f Turn the centre ring 4 on
off.
the stalk until the symbol is opposite
mark 5, then release it.
Depending on the vehicle, the stalk re-
turns to the initial position or stays in
position.
When driving in fog or snow, or
Operation of the fog lights depends on when transporting objects which are
the exterior lighting selected, and an in- higher than the roof, the headlights
dicator light will light up on the instru- do not come on automatically.
ment panel.
Switching on the fog lights remains
To avoid inconveniencing other road the responsibility of the driver: the
users, remember to switch off the rear indicator lights on the instrument
fog light when it is no longer needed. panel inform you whether the fog
lights are lit (indicator light on) or not
(indicator light not on).
1.67
AUDIBLE AND VISUAL SIGNALS
Direction indicators
Move stalk 1 parallel to the steering
wheel and in the direction you are going 2
to turn it.
1
One-touch mode
When driving, it is possible that the
A steering wheel may not be turned suf-
ficiently to return the stalk automatically
to its starting position.
In this case, move the stick 1 to half-
way, then release it: it will return to its
initial position and the indicator light
flashes three times.
1.68
HEADLIGHT BEAM ADJUSTMENT (1/2)
3 et 4 Do not use
1.69
HEADLIGHT BEAM ADJUSTMENT (2/2)
Temporary adjustment
Open the bonnet and identify the mark-
ing B next to one of the front headlight
projectors.
For each headlight, using a screw-
driver, turn the screw 1 by a quarter
turn towards the - symbol to lower the
beams.
Return to the starting point once your
trip is over: turn the screw 1 by a quar-
ter turn towards the + symbol to raise
the beams.
1.70
WINDSCREEN WASH/WIPE (1/2)
Vehicles with automatic wiper
function
1 With the engine running, move stalk 1 2
1 E
A park.
A B automatic wiper function
When this position is selected,
B the system detects water on the
C windscreen and triggers the wipers
at a suitable wiping speed. It is
D possible to change the triggering
threshold and the time sweeps by
turning ring 2: F
E: minimum sensitivity
F: maximum sensitivity
With the ignition on, move stalk 1 NB: in foggy weather or during Special note
snowfalls, the wiping is not automati-
A park. cally triggered and remains under When driving, the wiping speed slows
B intermittent wiping. the drivers control. down whenever the vehicle stops. For
The wipers will pause for seve- example: the speed will change from
C normal wiping speed. a fast wiping speed to normal wiping
ral seconds between sweeps. It
is possible to change the time D fast wiping speed. speed.
between sweeps by turning ring 2. As soon as the vehicle moves off,
wiping will return to the speed originally
C normal wiping speed. selected.
D fast wiping speed. Any action on stalk 1 overrides and
cancels automatic operation.
Starting the vehicle with the stalk in
position D triggers a slow continuous
sweeping movement. Adjusting the
Position C is accessible with the ig- stalk to position D is necessary to trig-
Positions B, C and D are accessible nition on. Positions B and D are ac- ger a rapid continuous sweeping move-
with the ignition on. cessible only with the engine run- ment.
ning.
1.71
WINDSCREEN WASH/WIPE (2/2)
1.72
REAR SCREEN WASH/WIPE
Rear screen wash/wipe
p With ignition on, turn the end
of the stalk 1 to bring the mark 2 in line
1 with the symbol. When the stalk is re-
2 leased, it returns to the rear windscreen In freezing or snowy weather, ensure
wiper position. they are not stuck to the windscreen
A short pull triggers the rear windscreen (including the central area located
wipers. behind the interior rear-view mirror)
A prolonged action triggers, in addition and the rear screen before starting
to the rear windscreen wipers, a contin- the wipers (risk of motor overheat-
uous sweep until the stalk is released, ing).
then two return wipes followed by a
third, after a few seconds. Check the condition of the wiper
blades. You are responsible for their
Special note service life:
they must remain clean: clean
If the windscreen wipers are operat- the blades, windscreen and
Speed-dependent
Y timed rear screen
ing or are in automatic mode, the rear
screen wiper wipes intermittently when
rear screen regularly with soapy
water;
wiper reverse gear is engaged. do not use them when the wind-
Depending on the vehicle, you can screen or rear screen are dry;
With the ignition on, turn the end of deactivate this function on the touch
stalk 1 to align mark 2 with the symbol. free them from the windscreen or
screen. Please see the equipment in- rear screen when they have not
Wiping frequency varies with speed. structions for further information. been used for a long time.
In all cases, replace them as soon
as they begin to lose efficiency: ap-
proximately once a year.
Before using the rear wiper, check
that no object obstructs the travel of
the blade.
Do not use the wiper arm to open or
Before any action on the windscreen (washing the vehicle, de-icing, close the tailgate.
cleaning the windscreen, etc.) return stalk 1 to the park position.
Risk of injury or damage.
1.73
FUEL TANK (1/3)
Fuel grade Petrol version
Use a high-grade fuel that complies It is essential to use unleaded petrol.
with the legislation in force in each The octane rating (RON) must comply
country and which must comply with with the information given on the label
1 the specifications given on the label on the cover A. Refer to Section 6 for
A on the cover A. Please refer to the in- information on Engine specifications.
formation on Engine specifications in
Section 6.
2 B Diesel version
Only use diesel fuel which complies
with the information on the label located
inside the cover A.
1.74
FUEL TANK (2/3)
Filling with fuel
With the ignition off, insert the nozzle
and insert it fully before turning it on to
fill the fuel tank (risk of splashing). 3
Keep the nozzle in this position through-
out the entire filling operation.
When the pump cuts out automatically
at the end of the filling procedure, a
maximum of two further filling attempts
may be made, as there must be suffi-
cient space in the fuel tank to allow for
expansion.
Make sure that no water enters the fuel
tank during filling. The cover A and its
surround must remain clean.
1.75
FUEL TANK (3/3)
3 5
4
No modifications what-
soever are permitted on
any part of the fuel supply
system (electronic units,
Running out of fuel on diesel Vehicles without priming bulb 4
wiring, fuel circuit, injectors, pro-
versions Insert the RENAULT card into the 5 tective covers, etc.) as this may be
Vehicles with priming bulb 4 card reader. Press the start button 3 dangerous (unless undertaken by
After a breakdown caused by com- without pressing any of the pedals. Wait qualified Network personnel).
pletely running out of fuel, the system a few minutes before starting. This will
must be reprimed before the engine is enable the fuel circuit to be primed. If
restarted: the engine does not start, repeat the
Fill the tank with at least 8 litres of procedure.
diesel fuel.
Press priming bulb 4 several times.
The engine can now be restarted.
If the engine does not start after several The engine may be hot
attempts, contact an approved Dealer. when working in close prox-
imity. In addition, the engine
cooling fan may come on at
any moment.
Risk of injury.
1.76
Section 2: Driving
(Advice on use relating to fuel economy and the environment)
Running in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2
Starting/stopping the engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3
Stop and Start Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6
Special features of petrol versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.10
Special features of Diesel versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.11
Gear lever/Handbrake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.12
Driving advice, Eco-driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.13
Maintenance and antipollution advice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.18
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.19
Tyre pressure loss warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.20
Driver correction devices/aids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.27
Speed limiter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.32
Cruise control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.35
Parking distance control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.39
Reversing camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.41
Automatic gearbox. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.43
2.1
RUNNING IN
Petrol version Diesel version
For the first 600 miles (1,000 km), do For the first 1,000 miles (1,500 km),
not exceed 78 mph (130 km/h) in the do not exceed 80 mph (130 km/h) in
highest gear, or 3,000 to 3,500 rpm. the highest gear, or 2,500 rpm. After
You may only expect top performance completing this mileage you may drive
from your vehicle after approximately faster, although you may only expect
1,800 miles (3,000 km). top performance after approximately
3,600 miles (6,000 km).
Service intervals: refer to the
Maintenance Document for your vehi- During the running in period, do not ac-
cle. celerate hard while the engine is still
cold and do not let the engine over-rev.
Service intervals: refer to the
Maintenance Document for your vehi-
cle.
2.2
STARTING/STOPPING THE ENGINE (1/3)
Special features
vehicles with an automatic gearbox
2.3
STARTING/STOPPING THE ENGINE (2/3)
For other functions: Operating faults
vehicles with remote control In certain cases, the hands-free
RENAULT card, insert the card into RENAULT card may not work:
1 reader 2;
2 when the RENAULT card battery is
vehicles with a RENAULT hands- drained, flat battery, etc.
free card, with the card in the pas-
senger compartment or inserted in near to appliances operating on the
the card reader 2, press button 1 wi- same frequency as the card (moni-
thout depressing the pedals. tor, mobile phone, video game, etc.);
2.4
STARTING/STOPPING THE ENGINE (3/3)
Remote control RENAULT When you leave your vehi-
card cle, especially if you have
With the card in reader 2, press your RENAULT card with
1 button 1: the engine will stop. Removing you, check that the engine
2 is completely switched off.
the card from the reader locks the stee-
ring column.
2.5
FUNCTION STOP AND START (1/4)
This system enables a reduced fuel For vehicles equipped with manual
consumption and lower greenhouse gearboxes:
gas emissions. The system is acti- the gearbox is in neutral;
vated automatically when the vehicle is and
started. While driving, the system stops the clutch pedal is released.
the engine (standby) when the vehicle
is at a standstill (traffic jam, traffic lights, If the warning light flashes,
this means that the clutch pedal is
etc).
not sufficiently released;
and
Conditions for engine the vehicle speed is less than ap-
standby proximately 7 mph (3 km/h).
The vehicle has set off from where it
was parked;
In all vehicles, the warning light
on the instrument panel is lit when the
Engine on standby - braking
For vehicles equipped with auto- assistance is no longer op-
matic gearboxes: engine is on standby. erational.
the gearbox is in position D, M or N; The vehicle equipment remain opera-
and tional while the engine is stopped.
the brake pedal is depressed (suffi- Keep your vehicle station-
ciently hard); ary when the engine is
and on standby (shown by the
the accelerator pedal is not de-
pressed;
and
warning light
instrument panel).
on the
2.6
FUNCTION STOP AND START (2/4)
Preventing the engine from Conditions for coming out of
standing by engine standby
In certain situations, such as negotiat- For vehicles equipped with auto-
ing a crossroads for instance, it is pos- matic gearboxes:
sible to keep the engine running so as the brake pedal is released, position
to be ready to move off quickly. D or M engaged or,
For vehicles equipped with auto- the brake pedal is released, position
matic gearboxes: N engaged and the handbrake off, or
Keep the vehicle stationary without the brake pedal is pressed again,
pressing too hard on the brake pedal with position P engaged or position
N engaged with the handbrake ap-
For vehicles equipped with manual plied, or
gearboxes: position R is engaged or,
Keep the clutch pedal pressed right the accelerator pedal is pressed.
down For vehicles equipped with manual
gearboxes:
the gearbox is in neutral and the
clutch pedal is slightly depressed, or
the engine is in gear and the clutch
pedal is pressed right down.
2.7
FUNCTION STOP AND START (3/4)
Conditions preventing the for vehicles with automatic gear- Special cases
standby of the engine boxes, the gradient is steeper than
approximately 12%; With the engine on standby (traffic jam,
Certain conditions prevent the system traffic lights, etc.), if the driver unfastens
from using the engine standby function, the Clear View function is activated their seat belt, opens the drivers door
including when: (please see Automatic Climate or gets out of their seat, the ignition will
Control in Section 3); be switched off.
reverse gear is engaged;
the engine temperature is too low; To restart and reactivate the Stop and
the bonnet is not locked; Start system, press the start button
the emission control system is being
the drivers door is not closed; regenerated; (please see Starting, stopping the
or engine in Section 2).
the drivers seatbelt is not fastened;
...
the outdoor temperature is too low or
too high (less than around 0 C or
higher than around 30 C);
The warning light or, depend-
ing on the vehicle, the message AUTO
the battery is not sufficiently charged; STOP UNAVAILABLE appears on the
the difference between the vehicle instrument panel indicating that engine
interior temperature and the auto- standby is not available.
matic climate control instruction is
too high;
2.8
FUNCTION STOP AND START (4/4)
Special feature of the automatic The system reactivates automati-
engine re-start cally each time the vehicle is started
Under certain conditions, the engine using the start button (please refer
can restart on its own in order to guar- to Starting, stopping the engine in
antee your safety and comfort. Section 2).
This can occur especially when: 1
the outdoor temperature is too low or Operating faults
too high (less than around 0 C or When the message Check Stop &
higher than around 30 C); Start appears on the instrument panel
the Clear View function is activated 2 and the integrated warning light 2 lights
(please see Automatic Climate up on the switch 1, the system is deac-
Control in Section 3); tivated.
the battery is not sufficiently charged; Please consult an authorised dealer.
the vehicle speed is above 3 mph
(5 km/h) (downhill slope, etc.);
repeated pressing on the brake Deactivating, activating the
pedal or braking system require-
ment;
function
... Press switch 1 to deactivate the func-
tion. The message Stop & Start deac-
tivated will appear on the instrument
panel and the integrated warning light 2
on the switch will light up.
Pressing again will reactivate the
system. The message Stop & Start ac-
tivated will appear on the instrument
panel and the integrated warning light 2
on switch 1 will go out. Before getting out of the
In the event of an emer- vehicle, you must switch
gency, the engine can be off the ignition by pressing
restarted by pressing on the the engine stop (please see
Note: With the engine on standby, Starting, stopping the engine).
clutch pedal if the Stop and press switch 1 to automatically re-
Start function is activated. start the engine.
2.9
SPECIAL FEATURES OF PETROL VERSIONS
The following operating conditions: If you notice any of the above operating
driving for long periods when the low faults, have the necessary repairs car-
fuel level warning light is lit; ried out as soon as possible by an ap-
proved Dealer.
using leaded petrol;
These faults may be avoided by regu-
using fuel or lubrication additives larly taking your vehicle to an approved
which are not approved. Dealer at the intervals specified in the
Or operating faults such as: Maintenance document.
faulty ignition system, running out of
fuel or disconnected spark plugs re- Starting problems
sulting in the engine misfiring or cut- To avoid damaging the catalytic con-
ting out when driving; verter, do not keep trying to start the
loss of power, engine (using the start button, or by
pushing or towing the vehicle) without
as they may cause the catalytic con-
having identified and corrected the
verter to overheat and thus reduce its
starting fault.
efficiency, or damage it irreparably
and cause heat damage to the vehi- If the fault cannot be identified, do not
cle. keep trying to start the engine, but con-
tact an approved Dealer.
2.10
SPECIAL FEATURES OF DIESEL VERSIONS
Diesel engine speed Precautions to be taken in
Diesel engines are fitted with an injec- winter
tion pump which prevents the engine To avoid any faults in icy weather:
speed being exceeded irrespective of
the gear selected. ensure that the battery is always fully
charged,
If the message Check antipollution
system is displayed along with warn- always keep the diesel tank rela-
tively full to avoid water vapour con-
ing lights and , consult an
authorised dealer immediately.
densing in it and accumulating at the
bottom of the tank.
When driving, depending on the fuel
grade used, it is possible that white
smoke may be emitted.
This is due to the exhaust particle filter
being cleaned automatically, and does
not affect the way the vehicle runs.
2.11
GEAR LEVER/HANDBRAKE
Handbrake
To release:
1 Pull the lever 3 up slightly, press
button 2 and then lower the lever to the
floor.
The red warning light on the instrument
2 panel will come on if you are driving
with an incorrectly released handbrake.
3 To apply:
Pull lever 3 upwards. Check that the
vehicle is immobilised. The warning Make sure that the hand-
D
light
come on.
on the instrument panel will brake is properly released
when driving (red indicator
Gear lever light off), otherwise over-
heating, or even damage, may
Selecting reverse gear occur.
Vehicles with manual gearbox: refer
to the grid on the gear lever knob 1. An impact to the under-
Vehicles with automatic gear- side of the vehicle while When stationary, and de-
box: refer to the information on the manoeuvring (e.g.: strik- pending on the slope and/or
Automatic gearbox in Section 2. ing a post, raised kerb or vehicle load, it may be nec-
other street furniture) may result in essary to pull up the hand-
The reversing lights will come on as
damage to the vehicle (e.g.: defor- brake at least two extra notches and
soon as reverse gear is selected with
mation of an axle). engage a gear (1st or reverse gear)
the ignition on.
To avoid any risk of accident, have for vehicles with a manual gearbox
your vehicle checked by an ap- or position P for vehicles with an au-
proved Dealer. tomatic gearbox.
2.12
DRIVING ADVICE, ECO-DRIVING (1/5)
Fuel consumption is accredited in ac- Driving style indicator 2
cordance with a standard regulatory
Informs you about the driving style
method. Identical for all manufactu-
adopted in real time. You will be notified
rers, this enables vehicles to be com-
by the colour of warning light 2.
pared with one another. Consumption
in real time depends on vehicle usage 1 Green: measured, economical driv-
conditions, the equipment fitted and the ing;
users driving style. To optimise fuel Yellow: opt for a calmer driving style;
consumption, please refer to the fol- Orange: driving too fast.
lowing advice. The driving style indicator is activated
2
Depending on the vehicle, you will have by default. If you wish to deactivate it,
various functions which enable you to please see the multimedia system in-
lower your fuel consumption: structions.
the rev counter;
gear change indicator;
the driving style indicator; Gear change indicator 1
the journey record and eco-driving
advice via the multimedia display; Depending on the vehicle, to obtain op-
ECO mode activated by the ECO timum consumption levels, a warning
button. light on the instrument panel lets you
know the best time to move up or down
If fitted on the vehicle, the navigation a gear:
system provides additional information.
move up a gear;
2.13
DRIVING ADVICE, ECO-DRIVING (2/5)
An overall rating from 0 to 100 is dis-
played to let you assess your eco driv-
ing performance. The higher the rating,
the lower the fuel consumption.
3 Eco advice is given to help improve
your performance.
With your favourite journeys saved, you
can evaluate your performance.
For more information, please see the
multimedia system instructions.
Journey record
Once the engine is switched off, you
will see Journey record displayed on
the screen 3, enabling you to view in-
formation relating to your last journey.
This indicates:
average fuel consumption;
number of miles/kilometres travelled;
number of miles/kilometres saved.
2.14
DRIVING ADVICE, ECO-DRIVING (3/5)
ECO mode
ECO mode is a function which opti-
mises fuel consumption. It acts on all
elements which consume fuel (engine
power, heating and/or air conditioning,
etc). 4
The 5 warning light comes on on The 5 light goes out on the ins-
trument panel to confirm deactivation.
the instrument panel to confirm activa-
tion.
While driving, it is possible to leave the
ECO mode temporarily in order to im-
prove engine performance.
Do this by pressing the accelerator
pedal down firmly and fully.
ECO mode is reactivated when you
take pressure off the accelerator pedal.
2.15
DRIVING ADVICE, ECO-DRIVING (4/5)
Avoid sudden acceleration.
Brake as little as possible. If you an-
ticipate an obstacle or bend in ad-
vance, you may then simply release
the accelerator pedal.
Do not try to maintain the same
speed up a hill, accelerate no more
than you would on the level. Keep
your foot in the same position on the
accelerator pedal.
Double declutching and accelerating
before switching off are unnecessary
in modern vehicles.
Bad weather, flooded roads:
2.16
DRIVING ADVICE, ECO-DRIVING (5/5)
In vehicles fitted with air condi-
tioning, it is normal to observe an
increase in fuel consumption (espe-
cially in urban conditions) when it is
used. For vehicles fitted with manual
air conditioning, switch off the system
when it is not required.
Advice for reducing consumption
and therefore helping to preserve
the environment:
If the vehicle has been parked in the
sun, open the doors for a few mo-
ments to let the hot air escape before
starting the engine.
Do not leave an empty roof rack
Tyres Advice on use fitted to the vehicle.
It is better to fit a trailer for bulky ob-
An underinflated tyre increases fuel Favour ECO mode. jects.
consumption. Electricity is fuel; switch off all the When towing a caravan, fit a wind
The use of non-recommended tyres electrical components which are deflector and adjust it carefully.
can increase fuel consumption. not really needed. However (safety Avoid using the car for door-to-door
first), keep your lights on when the calls (short journeys with long waits
visibility is bad (see and be seen). in between) because the engine
Use the air vents. Driving with the never reaches its normal operating
windows open at 60 mph (100 km/h) temperature.
will increase fuel consumption by
4%.
Never fill the fuel tank right to the
brim to avoid overflow.
2.17
MAINTENANCE AND ANTIPOLLUTION ADVICE
Your vehicle complies with criteria for In addition, replacing engine, fuel Air filter, fuel filter: a choked ele-
recycling and recovering vehicles at the supply system and exhaust compo- ment will reduce efficiency. It must
end of their service life which will come nents with parts other than those origi- be replaced.
into force in 2015. nally recommended by the manufac- Ignition and idle speed: no adjust-
Some parts of your vehicle have there- turer may alter your vehicle so that it ment is needed.
fore been designed to facilitate future no longer complies with anti-pollution
recycling. regulations.
Exhaust gas monitoring
These parts are easy to remove so Have your vehicle adjusted and system
that they can be recovered and reproc- checked by an authorised dealer, in ac-
cordance with the instructions given in The exhaust gas monitoring system will
essed by recycling companies. detect any operating faults in the vehi-
your maintenance schedule: they will
By virtue of its design, moderate fuel have all the equipment necessary for cles antipollution system.
consumption and initial settings, your ensuring that your vehicle is maintained If this system malfunctions, toxic sub-
vehicle also conforms to current anti- to its original standard. stances may be released into the at-
pollution regulations. The manufac- mosphere or damage may occur.
turer is actively striving to reduce pol- This warning light on the in-
lutant exhaust gas emissions and to
save energy. But the fuel consumption
Engine adjustments
Spark plugs: for optimum condi-
strument panel will indicate if
there are any faults in the system:
of your vehicle and the level of pollutant tions of use, output and performance This lights up when the ignition is
exhaust gas emissions are also your the specifications laid down by our switched on and goes out when the
responsibility. Ensure that it is main- Design Department must be strictly engine is started.
tained and used correctly. applied.
If it lights up continuously, consult an
If the spark plugs have to be changed, approved Dealer as soon as possi-
Maintenance use the make, type and gap specified ble;
It is important to remember that fail- for your vehicles engine. Contact an
authorised dealer for this. if it flashes, reduce the engine speed
ure to respect antipollution regulations until the light stops flashing. Contact
could lead to legal action being taken an authorised dealer as soon as pos-
against the vehicle owner. sible.
2.18
ENVIRONMENT
Your vehicle has been designed with Emissions At the end of the vehicles service
respect for the environment in mind for life, it should be sent to approved
its entire service life: during production, Your vehicle has been designed to centres to ensure that it is recycled.
use and at the end of its life. emit fewer greenhouse gases (CO2)
while in use, and therefore to consume In all cases, comply with local legis-
This commitment is illustrated by the lation.
Renault eco signature. less fuel (eg. 140 g/km, equivalent to
5.3 l/100 km for a diesel vehicle).
Our vehicles are also equipped with a Recycling
Manufacture particle filter system including a cata-
Your vehicle is 85% recyclable and
Your vehicle has been manufactured at lytic converter, an oxygen sensor and
95% recoverable.
a factory which complies with a policy an active carbon filter (the latter pre-
to reduce the environmental impact vents vapour from the fuel tank being To achieve these objectives, many of
on the surrounding areas (reduction of released into the open air). the vehicle components have been de-
water and energy consumption, visual signed to enable them to be recycled.
For certain diesel vehicles, this system
and noise pollution, atmospheric emis- The materials and structures have
also has a particle filter to reduce the
sions and waste water; sorting and re- been carefully designed to allow these
volume of soot particles emitted.
using waste). components to be easily removed and
reprocessed by specialist companies.
Please make your own In order to preserve raw material re-
contribution towards sources, this vehicle incorporates nu-
protecting the environment merous parts made from recycled plas-
too tics or renewable materials (vegetable
or animal-derived materials such as
Worn parts replaced in the course of cotton or wool).
routine vehicle maintenance (vehi-
cle battery, oil filter, air filter, batter-
ies, etc.) and oil containers (empty or
filled with used oil) must be disposed
of through specialist organisations.
2.19
TYRE PRESSURE LOSS WARNING (1/7)
A
2.20
TYRE PRESSURE LOSS WARNING (2/7)
Operating conditions driving with snow chains;
The system should be reset with an fitting a single new tyre;
inflation pressure equal to that given use of tyres not approved by the net-
on the tyre inflation pressure label. work.
Otherwise it risks not giving a reliable ...
warning in the event of a significant loss
of pressure. Please refer to the informa-
tion on Tyre pressures in Section 4.
1
In the following situations, the system
risk coming into action late or not func-
tioning correctly:
system not reset after reinflation or
any operation on the wheels;
system badly reset: different inflation
pressures from the recommended
SYSTEM A pressures;
significant change in load or distribu-
Operating principle tion of load on one side of the vehi-
This system detects a loss of pressure cle;
in one of the tyres by measuring the sporty driving with strong accelera-
This function is an addi-
wheel speed while driving. tion;
tional driving aid.
driving on snowy or slippery surface;
Warning light 1 comes on to
alert the driver in the event of insuffi-
However, the function does
not take the place of the
cient pressure (deflated wheel, punc- driver. It cannot, therefore, under
tured tyre, etc.). any circumstances replace the vig-
ilance or the responsibility of the
driver.
Check the tyre pressures, including
the emergency spare wheel, once a
month.
2.21
TYRE PRESSURE LOSS WARNING (3/7)
SYSTEM A (cntd.) Display
The display 2 on the instrument panel
Resetting the standard level for the 2 informs you of any tyre pressure faults
tyre pressures (flat tyre, punctured tyre, etc.).
This should be done: 3
INFLATE TIRES AND SET TPW
after each reinflation or readjustment
of the pressure of one of the tyres; Warning light comes on, along
with the message INFLATE TIRES
when the standard tyre pressure 4
needs to be changed to adapt to AND SET TPW. They indicate that at
usage conditions (empty, carrying a least one tyre is flat or punctured.
load, motorway driving, etc.); In the event of a flat tyre, inflate the re-
levant tyre.
after changing a wheel; In the event of a puncture, change the
after using the tyre inflation kit; tyre or consult an authorised dealer.
Check and readjust the pressure of the
after swapping a wheel (however, four tyres when cold, and launch the
this practice is not recommended). Resetting procedure
reset of the tyre pressure reference
With the ignition on:
It should always be done after checking
the tyre pressure of all four tyres when
repeatedly press one of the but-
tons 3 or 4 to select the TIRES SET
value. Warning light goes out
after launching the reinitialisation of the
cold.
TPW function on the display 2; tyre pressure reference value.
Tyre pressures must correspond to the press and hold (around 3 seconds)
current usage of the vehicle (empty, button 3 or 4 to start initialisation.
carrying a load, motorway driving, etc.). The display of the message SET
TPW LAUNCHED for around five
seconds indicates that the reset re-
quest for the tyre pressure reference
value has been taken into account.
Reinitialisation is carried out after a few
minutes driving.
2.22
TYRE PRESSURE LOSS WARNING (4/7)
SYSTEM A (cntd.) Readjustment of tyre pressures After each change of wheel/tyre, read-
The tyre pressures must be adjusted just the tyre pressure and launch the
RECALIBRATE SET TPW reset of the tyre pressure reference
when cold (please refer to the label lo-
value.
The warning light flashes for
several seconds, then stays on, along
cated on the edge of the drivers door).
If tyre pressures cannot be checked Emergency spare wheel
with the message RECALIBRATE SET when the tyres are cold, the recom-
TPW. If fitted on the vehicle, readjust the tyre
mended pressures should be increased pressure and launch the reinitialisation
They indicate that the request to reset by 0.2 to 0.3 bar (3 PSI). of the tyre pressure reference value.
the reference value of the tyre pres- Never deflate a hot tyre.
sures must be restarted. Tyre repair product and inflation kit
After each reinflation or readjustment of
TPW NOT AVAILABLE the tyre pressure, launch the reinitiali- Only use equipment approved by the
sation of the tyre pressure reference brand network, or the system risks
The warning light flashes for sev-
eral seconds, then stays on, along with
value. being activated late or not operating
correctly. Please refer to Tyre inflation
the message TPW NOT AVAILABLE. Replacing wheels/tyres kit in Section 5.
They indicate that the vehicle is Only use equipment approved by the After using the tyre inflation kit, readjust
equipped with an emergency spare brand network, or the system risks the tyre pressure and launch the reini-
wheel which is smaller than the other being activated late or not operating tialisation of the tyre pressure reference
four and that it is fitted to the vehicle. correctly. Please see the information on value.
CHECK TPW Tyres in Section 5.
2.23
TYRE PRESSURE LOSS WARNING (5/7)
Resetting the standard level for the
tyre pressures
This should be done:
when the standard tyre pressure
needs to be changed to adapt to
usage conditions (empty, carrying a
load, motorway driving, etc.);
after swapping a wheel (however
1 this practice is not recommended);
after changing a wheel.
It should always be done after checking
the tyre pressure of all four tyres when
cold.
Tyre pressures must correspond to the
current usage of the vehicle (empty,
SYSTEM B carrying a load, motorway driving, etc.).
Operating principle
Each wheel (except for the emergency
spare wheel) has a sensor in the infla- This function is an addi-
tion valve which periodically measures tional driving aid.
the tyre pressure while driving.
However, the function does
Warning light 1 comes on to
alert the driver in the event of insuffi-
not take the place of the
driver. It cannot, therefore, under
cient pressure (deflated wheel, punctu- any circumstances replace the vig-
red tyre, etc.). ilance or the responsibility of the
driver.
Check the tyre pressures, including
the emergency spare wheel, once a
month.
2.24
TYRE PRESSURE LOSS WARNING (6/7)
Reinitialisation is carried out after a few PUNCTURE
minutes driving.
2
Note: The warning light comes on
steady, accompanied by the message
3 The standard tyre pressure cannot be
less than that recommended and indi- PUNCTURE and a beep.
cated on the door frame. This message is accompanied by the
warning light .
Display
4 The display 2 on the instrument panel They indicate that at least one wheel
informs you of any tyre pressure faults is punctured or severely underinfla-
(flat tyre, punctured tyre, etc.). ted. Replace it or contact an authorised
dealer if it is punctured. Top up the tyre
ADJUST TYRE PRESSURE pressure if the wheel is deflated.
Warning light comes on, along
with the message ADJUST TYRE
SYSTEM B (cntd.) PRESSURE.
These indicate that at least one tyre is
Resetting procedure flat.
With the ignition on: Check and, if necessary, readjust the
repeatedly press one of the but- pressures of the four wheels when cold.
tons 3 or 4 to select the LEARNING
THE TYRE PRESSURE function
The warning light
few minutes driving.
goes off after a
on the display 2;
press and hold (around 3 seconds)
button 3 or 4 to start initialisation. The
display of the message PRESSURE
REF ONGOING for around 5 sec-
onds indicates that the reset request Warning light re-
for the tyre pressure reference value quires you to stop immedi-
has been taken into account. ately, for your own safety,
The sudden loss of pressure in a as soon as traffic conditions
tyre (burst tyre, etc.) cannot be de- allow.
tected by the system.
2.25
TYRE PRESSURE LOSS WARNING (7/7)
SYSTEM B (cntd.) Readjustment of tyre pressures Emergency spare wheel
The tyre pressures must be adjusted If the vehicle is equipped with an emer- -
CHECK TYRE PRESSURE when cold (please refer to the label lo- gency spare wheel, it will not have a
SENSORS cated on the edge of the drivers door). sensor.
If tyre pressures cannot be checked
The warning light flashes for
several seconds, then stays on, along
when the tyres are cold, the recom- Tyre repair product and inflation kit
mended pressures must be increased Because the valves are specially desi-
with the message CHECK TYRE by 0.2 to 0.3 bar (3 PSI).
PRESSURE SENSORS. gned, only use equipment approved by
Never deflate a hot tyre. the approved network. Please refer to
This message is accompanied by the Tyre inflation kit in Section 5.
warning light . Replacing wheels/tyres
They indicate that at least one tyre is This system requires specific equip-
not fitted with sensors (e.g. emergency ment (wheels, tyres, hubcaps, etc.).
spare wheel). In other cases, contact Please see the information on Tyres
an authorised dealer. in Section 5.
Contact an approved Dealer to fit new
tyres and to find out about available ac-
cessories compatible with the system
and available from your dealer net-
work: the use of any other accessory
could affect the correct operation of the
system or damage a sensor.
2.26
DRIVING CORRECTION DEVICES AND AIDS (1/5)
Depending on the vehicle, this is com- Anti-lock braking system Operating faults:
posed of: (ABS)
anti-lock braking system (ABS); Under heavy braking, the ABS prevents
and x lit up on the in-
strument panel alongside messages
electronic stability program (ESC) the wheels from locking, allowing the CHECK ABS, CHECK BRAKING
with understeer control and trac- stopping distance to be managed and SYSTEM and Check ESC: ABS,
tion control; keeping control of the vehicle. ESC and emergency brake assist
Under these circumstances, the vehi- are deactivated. Braking is always
driver assistance with a trailer;
cle can be steered to avoid an obstacle enabled;
emergency brake assist; whilst braking. In addition, this system
grip control; can increase stopping distances, par-
ticularly on roads with low surface grip
xD , , and lit
up on the instrument panel alongside
hill start assistance. (wet ground etc.).
the message Braking system fault:
You will feel a pulsation through the
this indicates a fault in the braking
brake pedal each time the system is
system.
activated. The ABS does not in any
way improve the vehicle's physical per- In both cases, please consult an
formance relating to the road surface Authorised Dealer.
and road-holding. It is still essential to
follow the rules of good driving practice
(such as driving at a safe distance from
the vehicle in front etc.).
2.27
DRIVING CORRECTION DEVICES AND AIDS (2/5)
Electronic stability program Understeer control Operating faults
(ESC) with understeer control This system optimises the action of the When the system detects an operat-
and traction control ESC in the case of pronounced under- ing fault the message Check ESC and
steer (loss of front axle road holding).
Electronic stability control ESC
Traction control
warning light and appear
on the instrument panel. In this case,
This system helps you to keep control the ESC and traction control system
of the vehicle in critical driving condi- This system helps to limit wheelspin of are deactivated.
tions (avoiding an obstacle, loss of grip the drive wheels and to control the ve- Consult an approved dealer.
on a bend, etc.). hicle when pulling away accelerating or
decelerating.
Operating principle
Operating principle
A sensor in the steering wheel detects
Using the wheel sensors, the system
the direction selected by the driver.
measures and compares the speed of These functions are an ad-
Other sensors throughout the vehicle the drive wheels at all times and slows ditional aid in the event of
measure the actual direction. down their over-rotation. If a wheel is critical driving conditions,
The system compares driver input to starting to slip, the system brakes au- enabling the vehicle behav-
the actual trajectory of the vehicle and tomatically until the drive supplied be- iour to be adapted to suit the driving
corrects the trajectory if necessary by comes compatible with the level of grip conditions.
controlling the braking of certain wheels under the wheel again.
However, the functions do not take
and/or engine power. In the event that The system also adjusts the engine the place of the driver. They do
the system is engaged, indicator light speed to the grip available under the not increase the vehicles limits
wheels, independently of the pressure
flashes on the instrument panel. exerted on the accelerator pedal.
and should not encourage you
to drive more quickly. Therefore,
they can under no circumstances
replace the vigilance or responsibil-
ity of the driver when manoeuvring
the vehicle (the driver must always
be ready for sudden incidents which
may occur when driving).
2.28
DRIVING CORRECTION DEVICES AND AIDS (3/5)
Emergency brake assist Hazard warning lights switching on
Depending on the vehicle, these may
This system supplements the ABS light up in the event of sudden decel-
and helps reduce vehicle stopping dis- eration.
tances.
Braking anticipation
Operating principle Depending on the vehicle, when you
The system allows an emergency brak- rapidly release the accelerator, the
ing situation to be detected when the system anticipates the braking ma-
brake pedal is pressed. In this case, the noeuvre in order to reduce stopping
braking assistance immediately devel- distances.
ops maximum power and may trigger When using the cruise control:
ABS regulation. if you use the accelerator, when you
ABS braking is maintained as long as release it, the system may be trig- These functions are an ad-
the brake pedal is applied. gered; ditional aid in the event of
if you do not use the accelerator, the critical driving conditions,
system will not be triggered. enabling the vehicle behav-
Operating faults iour to be adapted to suit the driving
When the system detects an operating conditions.
fault the message CHECK BRAKING However, the functions do not take
SYSTEM appears on the instrument the place of the driver. They do
panel along with the warning not increase the vehicles limits
light. and should not encourage you
to drive more quickly. Therefore,
Consult an approved dealer.
they can under no circumstances
replace the vigilance or responsibil-
ity of the driver when manoeuvring
the vehicle (the driver must always
be ready for sudden incidents which
may occur when driving).
2.29
DRIVING CORRECTION DEVICES AND AIDS (4/5)
Grip control Soft ground mode
Turn the button 1: the integrated warn-
If fitted on the vehicle, grip control
makes it easier to control the vehicle on
low grip surfaces (soft ground, etc.).
ing light comes on, along with
the instrument panel message NON
GRIP ROAD MODE ON.
This position enables optimal usage on
soft ground (mud, sand, dead leaves,
etc.). Soft ground mode uses traction
control functions. The system automati-
cally switches to Road mode after
around 25 mph (40 km/h), and the inte-
1 grated warning light on button 1
comes on.
Expert mode
Road mode Turn the button 1: the integrated warn-
When the vehicle is started up, the
warning light on button 1 comes
ing light comes on, along with
the instrument panel message ALL
on, along with the instrument panel ROADSMODE ON.
Tyres message STANDARD ROAD MODE In this position, engine speed is left
When they need to be re- ON. under the drivers control. The system
placed, only tyres of the This position enables optimal usage automatically switches to Road mode
same make, size, type and under normal driving conditions (dry- after around 25 mph (40 km/h), and
profile should be used.
Tyres fitted to the vehicle should
ness, humidity, light snow, etc.).
Road mode uses traction control func-
the integrated warning light
button 1 comes on.
on
either be identical to those fitted tions.
originally or conform to those
recommended by your approved
dealer.
2.30
DRIVING CORRECTION DEVICES AND AIDS (5/5)
Hill start assistance The hill start assistance
Depending on the gradient of the in- system cannot completely
cline, this system assists the driver prevent the vehicle from
when starting on a hill. It prevents the rolling backwards in all sit-
vehicle from rolling backwards, de- uations (extremely steep gradients,
pending on the slope, by automatically etc.).
applying the brakes when the driver lifts
In all cases, the driver may depress
his/her foot off the brake pedal to de-
the brake pedal to prevent the ve-
press the accelerator pedal.
hicle from rolling forwards or back-
System operation wards.
It only operates when the gear lever is The hill start assistance function
in a position other than neutral (other should not be used for prolonged
than N or P for automatic transmis- stops: use the brake pedal.
sions) and the vehicle is completely This function is not designed to im-
stationary (brake pedal depressed) mobilise the vehicle permanently.
The system holds the vehicle for ap- If necessary, use the brake pedal to
proximately 2 seconds. The brakes are stop the vehicle.
then gradually released (the vehicle will
The driver must remain particularly
move according to the slope).
vigilant when driving on slippery or
low-grip surfaces and/or on hills.
Risk of serious injury.
2.31
CRUISE CONTROL/SPEED LIMITER: speed limiter function (1/3)
1
2 3 4 5
2.32
CRUISE CONTROL/SPEED LIMITER: speed limiter function (2/3)
Varying the limit speed Exceeding the limit speed
The limit speed may be changed by re- It is possible to exceed the limit speed
peatedly pressing: at any time. To do this: press the accel-
switch 2 (+) to increase speed; erator pedal firmly and fully (beyond
the resistance point).
switch 3 (-) to reduce speed.
2 3 If the speed is exceeded, the limited
speed flashes on the instrument panel
accompanied by a beep.
Then, release the accelerator: the
speed limiter function will return as
soon as you reach a speed lower than
the stored speed.
2.33
CRUISE CONTROL/SPEED LIMITER: speed limiter function (3/3)
Recalling the limit speed
If a speed has been saved, it can be re-
called by pressing switch 4 ((R)).
2 3 4 5 1
2.34
CRUISE CONTROL/SPEED LIMITER: cruise control function (1/4)
1
2 3 4 5
2.35
CRUISE CONTROL/SPEED LIMITER: cruise control function (2/4)
1
7
2 3
2.36
CRUISE CONTROL/SPEED LIMITER: cruise control function (3/4)
Exceeding the cruising speed
The cruising speed may be exceeded
at any time by depressing the accelera-
tor pedal. While it is being exceeded,
the cruising speed flashes on the in-
strument panel.
2 3
Then, release the accelerator: after a
few seconds, the vehicle will automati-
cally return to its set cruising speed.
2.37
CRUISE CONTROL/SPEED LIMITER: cruise control function (4/4)
Returning to the cruising speed
If a speed is stored, it can be recalled,
once you are sure that the road con-
ditions are suitable (traffic, road sur-
face, weather conditions, etc.). Press
switch 4 (R) if the vehicle speed is 1
2 3 4 5 above 20 mph (30 km/h).
When the stored speed is recalled, acti-
vation of the cruise control is confirmed
by the illumination of the warning
light.
NB: if the speed previously stored is
much higher than the current speed,
the vehicle will accelerate more rapidly
to reach this threshold.
Putting the function on Switching off the function
standby The cruise control function is deacti-
The function is set to standby if you: vated if you press switch 1: in this case
a speed is no longer stored. The two in-
use the switch 5 (O);
strument panel warning lights and
the brake pedal; go out to confirm that the function is
depress the clutch pedal or the shift deactivated.
into neutral if the vehicle has an au-
tomatic gearbox.
In all three cases, the cruising speed
remains stored and the message When the cruise control function is
Putting the cruise control
MEMORISED appears on the instru- put on standby, pressing switch 2
on standby or switching it
ment panel. (+) reactivates the cruise control
off does not cause a rapid
function without taking into account
Standby is confirmed when indicator reduction in speed: you
the stored speed: it is the speed at
light goes out. must brake by depressing the brake
which the vehicle is moving that is
pedal.
taken into account.
2.38
PARKING DISTANCE CONTROL (1/2)
Operating principle
Ultrasonic detectors, installed in the
rear bumper (depending on the vehi- 1
cle), measure the distance between the
vehicle and an obstacle whilst revers-
ing.
This measurement is indicated by
beeps which become more frequent the
closer you come to the obstacle, until
they become a continuous beep when
the vehicle is approximately 30 centi-
metres from the obstacle.
NB: make sure that the ultrasonic sen-
sors are not obscured (by dirt, mud,
snow, etc.).
Note: depending on the vehicle, the Operation
screen 1 shows the vehicle surround-
ings alongside the beeps. When reverse gear is selected, most
objects which are less than approxi-
mately 1.20 metres from the rear of the
vehicle are detected, a beep sounds
and, depending on the vehicle, the dis-
play 1 comes on.
This function is an additional aid that indicates the distance between the
vehicle and an obstacle whilst reversing, using sound signals.
Under no circumstances should it replace the drivers care or responsibil-
ity whilst reversing.
The driver should always look out for sudden hazards during driving: always
ensure that there are no moving obstacles (such as a child, animal, pram or bi-
cycle, etc.) or small, narrow objects such as stones or posts in your path when
manoeuvring.
2.39
PARKING DISTANCE CONTROL (2/2)
Operating faults
Depending on the vehicle, when the
system detects an operating fault, the
1 message check parking distance con-
2 trol appears on the instrument panel,
accompanied by the warning light
and a beep lasting approxi-
mately 5 seconds. Please contact an
authorised dealer.
2.40
REVERSING CAMERA (1/2)
Operation Note:
This function is an additional
When going into reverse gear (and up ensure that the reversing camera is
aid. It cannot, therefore,
to around 5 seconds after shifting into not obscured (dirt, mud, snow, etc.);
under any circumstances
another gear), the camera 1 placed depending on the vehicle, certain
replace the vigilance or the
next to the lights transmits a view of settings can be adjusted from the
responsibility of the driver.
the rear surroundings of the vehicle on touch screen 2. Refer to the hand-
The driver should always pay atten-
the touch screen 2, accompanied by a book for the equipment.
tion to sudden incidents during driv-
mobile and fixed gauge. ing: always ensure that there are no
This system is initially used with the aid moving obstacles (such as a child,
of several gauges (mobile for trajectory animal, pram, bicycle, etc.) or small,
and fixed for distance). When the red narrow objects such as stones or
zone is reached, use the bumper image posts in your path when manoeu-
to stop accurately. vring.
2.41
REVERSING CAMERA (2/2)
Static guide line 4:
The fixed clearance gauge comprises
coloured markers A, B and C, indicat-
3 4 ing the distance behind the vehicle:
A (red) approximately 30 centime-
C tres from the vehicle;
B (yellow) approximately 70 centi-
B metres from the vehicle;
C (green) approximately 150 centi-
A metres from the vehicle.
This gauge remains fixed and indicates
the vehicle trajectory if the wheels are
in line with the vehicle.
2.42
AUTOMATIC TRANSMISSION (1/3)
Driving in automatic mode
Move lever 1 to position D.
1 In most road conditions you will en-
2 counter, you will not need to touch your
3 lever again: the gears will change au-
tomatically at the right time and at the
most suitable engine speed because
4 the automatic system takes into ac-
count the vehicle load and road contour
and adjusts itself to the particular driv-
ing style you have chosen.
Economical driving
When driving, always leave the lever
in position D, keeping the accelerator
Selector lever 1 Operation pedal lightly depressed to ensure auto-
P: park With the selection lever 1 in position P, matic gear changes at a lower engine
switch on the ignition. speed.
R: reverse
N: Neutral To move out of position P, you must de- Accelerating and overtaking
press the brake pedal before pressing
D: automatic mode Depress the accelerator pedal firmly
the unlocking button 2.
and fully (so that it goes beyond the
M: manual mode With the foot on the brake pedal (the kickdown point).
4: displays the gear engaged in manual warning light 3 on the display goes out),
This will enable you to change down
mode. move the lever out of position P.
to the optimum gear within the
Note: Press the button 2 to go from po- Only engage D or R when the vehi- engine range.
sition D or N to R or P. cle is stopped, with your foot on the
brake and the accelerator pedal re-
leased.
2.43
AUTOMATIC TRANSMISSION (2/3)
Special cases Special circumstances
In certain driving conditions (for exam- If the bends and road surface do
ple, engine protection, operation of the not allow you to stay in automatic
1 Electronic Stability Programme: the au- mode (e.g. in the mountains), we
tomatic system may change gear auto- recommend that you change to
matically. manual mode. This will prevent the
Likewise, to prevent incorrect manoeu- automatic gearbox from changing
vres, a gear change may be refused by gear repeatedly when climbing, and
the automatic system: in this case the permit engine braking on long de-
gear display flashes for a few seconds scents.
as a warning. In cold weather, start the engine
and wait a few seconds before
moving the selector lever from posi-
tion P or N and engaging it in D or R
to prevent the engine stalling.
Driving in manual mode
With the selection lever 1 in position D,
move the lever to the left.
Shifting the lever repeatedly allows you
to change gears manually:
to move down through the gears,
push the lever forwards;
to move up through the gears, push
the lever backwards.
The gear selected is displayed on the
instrument panel.
2.44
AUTOMATIC TRANSMISSION (3/3)
Parking the vehicle Operating faults
When the vehicle is stopped, move the when driving, if the check gearbox
lever to position P while keeping your message appears on the instrument
foot on the brake pedal: the gearbox is panel, it indicates a fault.
in neutral and the drive wheels are me- Contact your approved Dealer as 5
chanically locked by the driveshaft. soon as possible;
Apply the handbrake.
when driving, if the message
Gearbox overheating appears on
the instrument panel, stop as soon
as possible to let the gearbox cool
down and wait for the message to
disappear;
If a vehicle with an automatic
gearbox breaks down, refer to the
information on Towing in Section 5. When setting off, if the lever is locked
in position P even though you are
pressing the brake pedal, the lever can
be released manually. For this, unclip
the base of the lever then insert a tool
An impact to the under- (with a hard rod to it) into the slot 5 to
side of the vehicle while unlock the lever.
manoeuvring (e.g.: strik-
ing a post, raised kerb or Contact an authorised dealer as soon
other street furniture) may result in as possible.
damage to the vehicle (e.g.: defor-
mation of an axle).
To avoid any risk of accident, have
your vehicle checked by an ap- For safety reasons, do not
proved Dealer. switch off the ignition before
the vehicle has come to a
complete standstill.
2.45
2.46
Section 3: Your comfort
7 8 7
3.2
AIR VENTS, air outlets (2/2)
11 12
10
3.3
MANUAL AIR CONDITIONING (1/3)
1 2 3 4 The air conditioning system is used
for:
lowering the temperature inside the
passenger compartment;
eliminating condensation more
quickly.
6 5
The controls Switching air conditioning on
1 Adjusting the air temperature. or off
(depending on vehicle)
2 Adjusting the ventilation speed.
The air conditioning is switched on (in-
3 Air conditioning. dicator light on) or off (indicator light off)
4 Distribution of air in the passenger using button 3.
compartment. Activation is not possible if control 2 is
5 De-icing/demisting of the rear screen set to OFF.
and, depending on the vehicle, the
door mirrors.
6 Air recirculation.
3.4
MANUAL AIR CONDITIONING (2/3)
Distribution of air in the 1 2 3 4
passenger compartment
There are five air distribution options.
Turn control 4 to choose the distribution
option.
The air flow is directed to the
W windscreen and the front side
window demisting vents.
The air flow is distributed be-
i tween all the air vents, the
front side window demisting vents, the
windscreen demisting vents and the
footwells.
The air flow is directed mainly 6 5
towards the footwells.
Switching the air Air recirculation is for:
The air flow is directed towards recirculation on isolating the vehicle from the exter-
G the dashboard air vents, the
front footwells and, depending on the
Press button 6: the integrated indicator nal atmosphere (driving in polluted
areas, etc.);
light comes on. In these conditions, air
vehicle, the second row footwells. is taken from the passenger compart- lowering the passenger compart-
ment and is recycled, with no air being ment temperature as quickly as pos-
All the air flow is directed to the
J dashboard vents. taken from outside the vehicle. sible.
Prolonged use of air recirculation can lead to condensation forming on the side
windows and windscreen, and discomfort due to the use of non-renewed air in
the passenger compartment. We therefore advise you to return to normal mode
(external air) as soon as the air recirculation function is no longer required, by
pressing the button 6 again.
3.5
MANUAL AIR CONDITIONING (3/3)
1 4 2 3 4 Adjusting the air temperature
Turn control 1 to obtain the desired
temperature. The further towards the
red the slide is, the higher the tempera-
ture will be.
When the air conditioning system is
used for long periods, it may begin to
feel cold. To increase the temperature,
turn control 1 to the right.
3.6
AUTOMATIC CLIMATE CONTROL (1/4)
1 2 3 4 5 Varying the ventilation speed
In automatic mode, the system uses
the most suitable amount of air to reach
and maintain the desired comfort level.
You can still adjust the ventilation
speed by turning control 6 to increase
or reduce the ventilation speed.
3.7
AUTOMATIC CLIMATE CONTROL (2/4)
Clear View function 1 3 4
Press button 3 the integrated indica-
tor light comes on.
This function quickly demists and de-
ices the windscreen, the rear screen,
the front side windows, and the door
mirrors (depending on the vehicle). The
air conditioning and rear screen de-ic-
ing functions must be activated.
Press button 8 to stop the heated rear
screen operating, and the integrated in-
dicator goes out.
To exit this function, press button 3
or 1. 8
Adjusting the distribution The air flow is distributed be-
of air in the passenger
tween all the air vents, the
front side window demisting air vents
compartment and the windscreen demisting vents.
Press one of the buttons 4. The in-
The air flow is mainly directed
tegrated warning light in the button
comes on.
to the dashboard air vents.
The air flow is directed mainly
It is possible to combine two positions
simultaneously press both buttons 4.
towards the footwells.
3.8
AUTOMATIC CLIMATE CONTROL (3/4)
5
9
8
Rear screen de-icing/ Switching air conditioning on
demisting or off
Press button 8 the integrated indica- In automatic mode, the system switches
tor light comes on. This function en- the air conditioning system on or off,
ables rapid demisting or de-icing of the depending on the climate conditions.
rear screen and de-icing of the door Press button 5 to switch off the air
mirrors (on equipped vehicles). conditioning; the integrated indicator
To exit this function, press button 8 comes on.
again. Demisting automatically stops.
3.9
AUTOMATIC CLIMATE CONTROL (4/4)
Air recirculation (isolation of 1
the passenger compartment)
K
This function is managed automatically
(operation is confirmed by a warning
light on button 7), but you can also acti-
vate it manually.
NB:
during recirculation, air is taken from
the passenger compartment and
is recycled, with no air being taken
from outside the vehicle;
air recirculation allows the external 7 6
atmosphere to be cut off (when driv-
ing in polluted areas, etc.); Manual use Stopping the system
the recirculation of air makes it pos- Press button 7 the integrated indica- Turn the control 6 to OFF to stop the
sible to reach the desired passenger tor light comes on. system. To start it, turn the control 6
compartment temperature quicker. again, then adjust the fan speed or
Prolonged use of this position may lead
to odours, caused by non-renewal of press the button 1.
air, and the formation of condensation
on the windows.
We therefore advise you to return to au-
tomatic mode as soon as air recircula-
tion is no longer needed, by pressing
button 7.
To exit this function, press button 7
again.
3.10
AIR CONDITIONING: information and advice on use
Advice on use Fuel consumption Operating faults
In some situations, (air conditioning You will normally notice an increase in As a general rule, contact your ap-
off, air recirculation activated, ventila- fuel consumption (especially in town) proved dealer in the event of an oper-
tion speed at zero or low, etc.) you may when the air conditioning is operating. ating fault.
notice that condensation starts to form For vehicles fitted with air conditioning Reduction in de-icing, demisting
on the windows and windscreen. with no automatic mode, switch off the or air conditioning performance.
If there is condensation, use the Clear system when it is not required. This may be caused by the passen-
View function to remove it, then use Advice for reducing consumption ger compartment filter cartridge be-
the air conditioning in automatic mode and helping to preserve the environ- coming clogged.
to stop it forming again. ment No cold air is being produced.
Drive with the air vents open and the Check that the controls are set cor-
Maintenance windows closed. rectly and that the fuses are sound.
Otherwise, switch off the system.
Refer to the Maintenance Document If the vehicle has been parked in the
for your vehicle for the inspection fre- sun, open the doors for a few moments
quency. to let the hot air escape before starting Presence of water under the
the engine. vehicle
After prolonged use of the air condi-
tioning system, it is normal for water
to be present under the vehicle. This is
caused by condensation.
3.11
ELECTRIC WINDOWS (1/2)
These systems operate with the igni-
tion on or off, until one of the front doors
is opened (limited to about 3 minutes).
Electric windows
Press or pull the switch to raise or lower
a window to the desired height (the rear 6
windows do not open fully); 1
5
2
3
4
Passenger safety
The driver can prevent the
front and rear passenger From the drivers seat, use switch:
electric windows from op- 1 for the drivers side;
erating (and the drivers window) 2 for the front passenger side;
by pressing switch 4. A confirmation 3 and 5 for the rear passenger win-
message is displayed on the instru- Avoid resting any objects against dows.
ment panel. a half-open window: there is a risk From the passenger seats, use
that the electric window could be switch 6.
damaged.
Drivers responsibility
Never leave your vehicle with the RENAULT card or key inside, and never leave a child, adult who is not self-sufficient
or a pet, even for a short while. They may pose a risk to themselves or to others by starting the engine or activating
equipment (such as the gear lever or electric windows). If any part of the body becomes trapped, reverse the direction
of the window immediately by pressing the relevant switch.
Risk of serious injury.
3.12
ELECTRIC WINDOWS (2/2)
One-touch mode Operating faults
Depending on the vehicle, this mode In case of a fault when closing a window,
works in addition to the operation of the the system reverts to normal mode:
electric windows described previously. pull the switch concerned up as often
It is only fitted to the drivers window. as necessary to fully close the window
Briefly press or pull switch 1 fully: the (the window will close gradually), hold
window is fully lowered or raised. the switch (still on the closure side) for
Pressing the switch again stops the one second then lower and raise the
window moving. window fully to reinitialise the system.
NB: if the drivers window detects re- If necessary, contact your authorised
sistance when closing (e.g.: fingers, dealer.
branch of a tree, etc.), it stops and then
lowers again by a few centimetres.
3.13
INTERIOR LIGHTING
2 4 5
1 3
3.14
PASSENGER COMPARTMENT STORAGE, FITTINGS (1/5)
1 3
Front door storage pockets 1 Sun visor storage 2 Centre console storage
They can hold a 1.5-litre bottle. This can be used for storing motorway compartment 3
tickets, cards, etc.
3.15
PASSENGER COMPARTMENT STORAGE, FITTINGS (2/5)
6
4 5
7 8
3.16
PASSENGER COMPARTMENT STORAGE, FITTINGS (3/5)
9 11
10
Cup holders 10
This can be used for storing a mobile
ashtray, cup holder, etc.
3.17
PASSENGER COMPARTMENT STORAGE, FITTINGS (4/5)
13
14
12
Rear centre console storage Removable rear central Rear door storage
compartment 12 storage compartment 13 compartment 14
This can be used for storing a mobile It is fixed on the rear central storage They can hold a 0.5-litre bottle.
ashtray, cup holder, etc. console 12.
3.18
STORAGE, CABIN FITTINGS (5/5)/SUN VISOR
18
15 17
16
19
3.19
ASHTRAY, CIGARETTE LIGHTER, ACCESSORIES SOCKET
Accessories socket 1
It is provided for connecting accessories
approved by our Technical Department.
3
2
3.20
REAR HEAD RESTS
3.21
SLIDING REAR BENCH SEAT (1/2)
1
2
To move forwards or
backwards
To unlock the seat:
When moving the rear
in the rear, lift the two levers 1 simul- seats, ensure that nothing
taneously; obstructs the anchorage
from the boot, pull the handle 2. points (passengers arm or
leg, a pet, gravel, cloth, toys, etc.).
Move the seat forwards or back to the
required position.
Release lever 1 or handle 2 and make
sure that the seat is locked correctly in
position.
3.22
SLIDING REAR BENCH SEAT (2/2)
To replace the seatback, proceed in
the reverse order to removal.
Refit the seatback and click it back into
3 place.
A
B
3.23
BOOT
1
3
Lower the tailgate using the handles 2 access the luggage compartment by
inside the tailgate to help you. tilting the rear bench seatback(s),
insert a pencil or similar object in
recess 3 and slide the unit as shown
in the illustration;
push the tailgate to open it.
3.24
REAR PARCEL SHELF
A
B
2
2
3.25
BOOT FITTINGS (1/2)
2 2
3
1
3
1 1
3.26
BOOT FITTINGS (2/2)
3.27
TRANSPORTING OBJECTS IN THE LUGGAGE COMPARTMENT
Always position the objects transported
so that the largest surface is against:
3.28
TRANSPORTING OBJECTS towbar
3.29
ROOF BARS/SPOILER
Precautions during use
Handling the tailgate
1 Before handling the tailgate, check the A
objects and/or accessories (bike rack,
roof box, etc.) fitted to the roof bars:
these must be correctly positioned and
secured, so as not to hinder the opera-
tion of the tailgate.
3.30
MULTIMEDIA EQUIPMENT
The presence and location of this equip-
ment depends on the vehicle version.
1 Multimedia touchscreen; 1
2 Multimedia sockets;
3 Steering column control;
4 Voice commands;
5 Microphone.
4 5
2
3
3.31
3.32
Section 4: Maintenance
Bonnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2
Engine oil level: general information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4
Engine oil level: topping up/filling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5
Oil change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.6
Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7
engine coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7
Brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.8
windscreen washer reservoir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.9
Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.9
Tyre pressure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.10
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.12
Bodywork maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.13
Interior trim maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.15
Seat covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.17
4.1
BONNET (1/2)
To open the bonnet, pull the handle 1. Unlocking the bonnet catch
To open, push tab 2 to the left as you
open the bonnet. When working in the engine
compartment, ensure that
the windscreen wiper stalk
Opening the bonnet is in the park position.
Lift the bonnet, helping it up, and it will
Risk of injury.
rest in position with the help of struts.
4.2
BONNET (2/2)
Closing the bonnet
Check that nothing has been left in the
engine compartment.
To close the bonnet again, hold the
bonnet in the middle and lower it to
30 cm above the closed position, then
release it. It will latch automatically
under its own weight.
4.3
ENGINE OIL LEVEL: general information
It is normal for an engine to use oil for remove the dipstick and wipe with a
lubrication and cooling of moving parts
B clean, lint-free cloth;
and it is normal to top up the level be- A push the dipstick in as far as it will
tween oil changes. go (for vehicles equipped with a cap-
However, contact your approved type dipstick C, screw the cap in as
Dealer if more than 0.5 litres is being far as it will go);
consumed every 600 miles (1,000 km) take out the dipstick again;
after the running in period. C read the level: it should never fall
Oil change frequency: check the oil B below minimum mark A or exceed
level from time to time and certainly maximum mark B.
before any long journey to avoid the Once the operation has been com-
risk of damaging your engine. A pleted, ensure that the dipstick is
pushed in as far as it will go or that
the cap-type dipstick is completely
screwed in.
4.4
ENGINE OIL LEVEL: topping up/filling (1/2)
1
1
2
2 2
1
4.5
ENGINE OIL LEVEL: topping up, filling (2/2)OIL CHANGE
Oil change Engine oil grade
Service interval: refer to the Refer to the Maintenance Service
Maintenance Service Booklet for your Booklet for your vehicle.
vehicle.
4.6
LEVELS (1/3)
Frequency of checking coolant level Replacement interval
Check the coolant level regularly Refer to the Maintenance Document for
(very severe damage is likely to be your vehicle.
caused to the engine if it runs out of
1 coolant).
If the level needs to be topped up, only
use products approved by our Technical
Department which ensure:
protection against freezing;
an anti-corrosion protection for the
cooling system.
Coolant level
With the engine switched off and on
level ground, the level when cold must
be between the MINI and MAXI marks
on reservoir 1.
Consult your approved dealer at
Top this level up when cold before it once if you notice an abnormal or
reaches the MINI mark. repeated drop in any of the fluid
levels.
Before performing any
action in the engine com-
partment, the ignition must
When working in the engine be switched off by pressing No operations should be
compartment, ensure that the engine stop button (please see carried out on the cooling
the windscreen wiper stalk the information on Starting, stop- circuit when the engine is
is in the park position. ping the engine in Section 2). hot.
Risk of injury. Risk of burns.
4.7
LEVELS (2/3)
Level 2
It is normal for the level to drop as the
brake shoes become worn, but it must
never drop lower than the MINI" warn-
ing line.
If you wish to check the disc and drum
wear yourself, you should obtain the
document explaining the checking pro-
cedure from the manufacturers net-
2 work or web site.
Topping up
After any operation on the hydraulic cir-
cuit, a specialist must replace the brake
fluid.
Brake fluid level Only use fluids approved by our
The level should be read with the engine Technical Department (and taken from
switched off and on level ground. a sealed container).
This should be checked frequently, Replacement interval
and immediately if you notice even the
slightest loss in braking efficiency. Refer to the Maintenance Document for
your vehicle.
4.8
LEVELS (3/3)/FILTERS
Filters
The replacement of filter components
(air filter, cabin filter, diesel filter, etc.)
is scheduled in the maintenance opera-
tions for your vehicle.
Replacement intervals for filter el-
ements: refer to the Maintenance
3 Document for your vehicle.
4.9
TYRE PRESSURE (1/2)
Vehicle fitted with a tyre pressure
loss warning system
If under-inflated (puncture, low pres- A
A
sure, etc.), the warning light
the instrument panel comes on. See
on
4.10
TYRE PRESSURES (2/2)
Special note concerning fully laden Tyre safety and use of snow chains:
vehicles (Maximum Permissible All-Up Refer to the information on Tyres in
Weight) and towing a trailer: the maxi- Section 5 for the servicing conditions
mum speed must be limited to 60 mph and, depending on the version, the use
(100 km/h) and the tyre pressure in- of chains.
creased by 0.2 bar. For your safety, please re-
Please refer to the information on spect the speed limit.
Weights in Section 6. When they need to be re-
placed, only tyres of the
same make, size, type and profile
should be used on a single axle.
They must: either have a load ca-
pacity and speed rating at least
equal to those of the original
tyres, or conform to those recom-
mended by an authorised dealer.
Failure to heed these instructions
could endanger your safety and
affect your vehicles roadworthi-
ness.
Risk of loss of control of the ve-
hicle.
4.11
BATTERY
Depending on the vehicle, the battery 1 A 2 3 4
is located under a cover and does not
require any maintenance. You should
not open it or add any fluid.
2
7 6 5
Label A
Before performing any Observe the indications on the battery:
action in the engine com- 2 naked flames and smoking are for-
partment, the ignition must bidden;
be switched off by pressing 3 eye protection required;
Handle the battery with the engine stop button (please see 4 keep away from children;
care as it contains sulphu- the information on Starting, stop- 5 explosive materials;
ric acid, which must not ping the engine in Section 2). 6 refer to the handbook;
come into contact with eyes 7 corrosive materials.
or skin. If it does, wash the affected
area with plenty of cold water. If ne-
cessary, consult a doctor.
Ensure that naked flames, red hot The engine may be hot
objects and sparks do not come into The battery is a speci- when carrying out opera-
contact with the battery as there is a fic type, please ensure it tions in close proximity. In
risk of explosion. is replaced with the same addition, the engine cooling
type. Consult an approved fan can come on at any moment.
dealer. Risk of injury.
4.12
BODYWORK MAINTENANCE (1/2)
A well-maintained vehicle will last What you should not do You should
longer. It is therefore recommended to Do not degrease or clean mechani-
maintain the exterior of the vehicle reg- Wash your car frequently, with the
cal components (e.g. the engine com- engine off, with cleaning products rec-
ularly. partment), underneath the body, parts ommended by the manufacturer (never
Your vehicle has been treated with very with hinges (e.g. inside the doors) and use abrasive products). Rinse thor-
effective anti-corrosion products. It is painted plastic external fittings (e.g. oughly beforehand with a jet:
nevertheless subject to various outside bumpers) using high-pressure clean- spots of tree resin and industrial
influences. ing equipment or by spraying on prod- grime;
ucts not approved by our Technical mud in the wheel arches and under-
Corrosive agents in the atmosphere Department. Doing this could give rise neath the body which forms damp
atmospheric pollution (built-up and to corrosion or operational faults. patches;
industrial areas), Wash the vehicle in bright sunlight or bird droppings, which cause a
saline atmospheres (near the sea, freezing temperatures. chemical reaction with the paint that
particularly in hot weather), rapidly discolours paintwork and
seasonal and damp weather condi- Do not scrape off mud or dirt without
pre-wetting. may even cause the paint to peel
tions (e.g. road salt in winter, water off;
from road cleaners, etc.). Allow dirt to accumulate on the exterior. wash the vehicle immediately to
Allow rust to form following minor im- remove these marks since it is im-
Minor impacts possible to remove them by polish-
pacts.
Abrasive action ing;
Do not use solvents not approved by salt, particularly in the wheel arches
Dust and sand in the air, mud, road grit our Technical Department to remove
thrown up by other vehicles, etc. and underneath the body after driv-
stains as this could damage the paint- ing in areas where the roads have
You should take a number of minor pre- work. been gritted.
cautions in order to safeguard your ve- Do not drive in snow or muddy condi-
hicle against such risks. Remove any plant matter (resin, leaves,
tions without washing the vehicle, par- etc.) from the vehicle regularly.
ticularly under the wheel arches and
body.
4.13
BODYWORK MAINTENANCE (2/2)
Respect local regulations about wash- Vehicles with a matte paint Using a roller type car wash
ing vehicles (e.g. do not wash your ve- finish
hicle on a public highway). Return the windscreen wiper stalk to
This type of paint requires certain pre- the Park position (refer to the informa-
Observe the vehicle stopping distances cautions. tion on the Windscreen washer, wiper
when driving on gravelled surfaces to in Section 1). Check the mounting of
prevent paint damage. Do not do the following external accessories, additional lights
Repair, or have repaired quickly, areas and mirrors, and ensure that the wiper
use wax-based products (polishing);
where the paint has been damaged, to blades are secured with adhesive tape.
rub hard;
prevent corrosion spreading. Remove the radio aerial mast if your
wash the vehicle in a roller-type car
vehicle is fitted with this equipment.
Remember to visit the body shop pe- wash;
Remember to remove the tape and refit
riodically in order to maintain your wash the vehicle using a high-pres-
the antenna after washing.
anti-corrosion warranty. Refer to the sure device;
Maintenance Document. attach stickers to the paintwork (risk
If it is necessary to clean mechani-
of leaving marks). Cleaning the headlights
cal components, hinges, etc., spray You should do the following As the headlights are made of plastic
them with products approved by our glass, use a soft cloth or cotton wool
Technical Department to protect them Wash the vehicle by hand using plenty to clean them. If this does not clean
after they have been cleaned. of water, using a soft cloth or a gentle them properly, moisten the cloth with
sponge. soapy water, then wipe clean with a soft
damp cloth or cotton wool.
Finally, carefully dry off with a soft dry
cloth.
Cleaning products containing alco-
hol must not be used.
4.14
INTERIOR TRIM MAINTENANCE (1/2)
A well-maintained vehicle will last Glass instrument panel Textiles (seats, door trim, etc)
longer. It is therefore recommended to (e.g.: instrument panel, clock, exterior
maintain the interior of the vehicle regu- Vacuum-clean the textiles regularly.
temperature display, radio display, mul-
larly. timedia or multifunction display etc.) Liquid stain
A stain should always be dealt with Use a soft cloth (or cotton wool). Use soapy water.
swiftly. If this does not clean them properly,
use a soft cloth (or cotton wool) slightly Dab lightly (never rub) with a soft cloth,
Whatever type of stain is on the trim, rinse and remove the excess.
use cold (or warm) soapy water with moistened with soapy water and then
natural soap. wipe clean with another soft damp cloth
or cotton wool. Solid or pasty stain
Detergents (washing-up liquid, pow- Finally, carefully dry off with a soft dry Carefully remove the excess solid or
dered products, alcohol-based prod- cloth. pasty material immediately with a
ucts) should not be used. spatula (working from the edges to the
Do not use products containing alco-
Use a soft cloth. hol and/or spray fluids on the area. centre to avoid spreading the stain).
Clean as for a liquid stain.
Rinse and soak up the excess.
Seat belts Special instructions for sweets or
chewing gum
These must be kept clean.
Use products selected by our Technical Put an ice cube on the stain to solidify
Department (Approved outlets) or it, then proceed as for a solid stain.
warm, soapy water and a sponge and
wipe with a dry cloth.
Detergents or dyes must not be used
under any circumstances.
4.15
INTERIOR TRIM MAINTENANCE (2/2)
Removal/replacing removable You should not:
equipment originally fitted in You are strongly advised not to po-
the vehicle sition objects such as deodorants,
If you need to remove equipment in scents, etc. near air vents, as this could
order to clean the passenger com- damage your dashboard trim.
partment (for example, mats), always
ensure that they are correctly refitted
and are the right way around (the driv-
ers mat should be fitted on the drivers
side, etc.) and fit them with the compo-
nents supplied with the equipment (for
example, the driver mat should always
be fixed using the pre-fitted mounting
components).
With the vehicle stationary, always
ensure that nothing will impede driving
(anything obstructing the pedals, heel
wedged by the mat etc.).
4.16
SEAT COVERINGS (1/5)
4.17
SEAT COVERINGS (2/5)
Replacing the seatback cover Removing the base cover
Incline the seatback towards the Open the zip fastener 4 of the base;
2 rear; remove the cover according to the
position the cover on the seatback; method shown (movement A).
close the zip fasteners 1 and 3;
attach the self-grip bands 2; Replacing the base cover
attach the self-grip bands 5 between Position the base cover;
1 the seatback and the base; close the zip fastener 4 for the base;
attach the self-grip bands 6.
5 3
6
4
Front seat
Taking off the seatback cover
Incline the seatback towards the
rear;
open the zip fasteners 1 and 3 on the
seatback;
remove the self-grip bands 5 be-
tween the seatback and the base;
remove the cover according to the
method shown (movement A).
With the seat covers off,
ensure that the seatbelt
buckles and ISOFIX attach-
ments are clear. For safety reasons, carry
out these operations when
the vehicle is stationary.
4.18
SEAT COVERINGS (3/5)
7 9 9
B 8 7 8
B
Rear bench seat Removing the base cover B Replacing the base cover B
Bring the front seats forward; Open the zip fasteners 7 and 8 for Position the cover on the base B;
the base B; close the zip fasteners 7 and 8;
reinsert the headrest for the rear
bench seat; remove the cover according to the attach the self-grip bands 9.
method shown (movement A).
disengage the seat belts.
4.19
SEAT COVERINGS (4/5)
attach the self-grip bands;
10 11 15 ensure that the seatback cover is
correctly positioned C under the
guide of the central seatbelt 10;
attach the self-grip bands 13;
C slide the lower cover between the
seatback C and the base B;
fold down the seatback C to the base
C
14 12
using the stalk 11;
attach the self-grip bands 15 be-
tween the seatbackC and the
B base B;
13
reinsert the seatback C and ensure
that it is well locked;
Removing the seatback cover C Replacing the seatback cover C
fold down the seatback C to the base Position the cover on the seat-
using the stalk 11; back C;
remove the self-grip bands 15 be- keep the rear central seatbelt out of
tween the seatback and the base; the way to position the cover;
reinsert the seatback C and ensure close the zip fastener 12 and 14 of
the seatback C; When refitting the seat-
that it is well locked; back, make sure it is cor-
open the zip fasteners 12 and 14 for rectly locked in place.
the seat back C; If seat covers are fitted,
make sure these do not prevent the
remove the cover according to the
seatback latch from locking in.
method shown (movement A). With the seat covers off, Make sure that the seat belts are
ensure that the seatbelt positioned correctly.
buckles and ISOFIX attach- Reposition the headrests.
ments are clear.
4.20
SEAT COVERINGS (5/5)
Replacing the seatback cover D
Position the cover on the seat-
16 back D;
close the zip fastener 20;
17
attach the self-grip bands 19;
slide the lower cover between the
seatback D and the base;
D move the seatback D onto the base
D using the stalk16;
close the zip fastener 18 of the seat
back D;
attach the self-grip bands 17 be-
20 19 tween the seatback and the base;
18
raise the seatback D completely and
ensure that it is well locked.
Removing the seatback cover D open the zip fastener 20 of the seat
Fold down the seatback D to the back D;
base using the stalk 16; remove the cover according to the
remove the self-grip bands 17 be- method shown (movement A).
tween the seatback and the base;
open the zip fastener 18 of the seat When refitting the seat-
back D; back, make sure it is cor-
rectly locked in place.
reinsert the seatback D and ensure
If seat covers are fitted,
that it is well locked;
make sure these do not prevent the
seatback latch from locking in.
When moving the rear Make sure that the seat belts are
seats, ensure that nothing positioned correctly.
obstructs the anchorage Reposition the headrests.
points (passengers arm or
leg, a pet, gravel, cloth, toys, etc.).
4.21
4.22
Section 5: Practical advice
If the emergency spare wheel has been stored for several years, have it checked by your Dealer to ensure that it is
safe to use.
Vehicle fitted with an emergency spare wheel that differs from the other wheels:
Never fit more than one emergency spare wheel to the same vehicle.
Replace the emergency spare wheel as soon as possible with a wheel identical to the original one.
When this is fitted to the vehicle, which must only be a temporary measure, the driving speed must not exceed the speed
indicated on the label on the wheel.
Fitting an emergency spare wheel may alter the way the vehicle usually runs. Avoid sudden acceleration or deceleration and
reduce your speed when cornering.
If you need to use snow chains, fit the emergency spare wheel to the rear axle and check the tyre pressure.
The warning light on the instrument panel flashes for several seconds, then stays on.
5.2
TYRE PRESSURE KIT (1/3)
A tyre which has been punctured Keep the repair kit away from chil-
should always be inspected (and re- dren.
The kit repairs tyres when paired, where possible) as soon as Do not dispose of the empty bottle
tread A has been dam- possible by a specialist. in the countryside. Return it to your
aged by objects smaller When taking a tyre which has been approved dealer or to a recycling or-
than 4 mm. It cannot repair repaired using this kit to be replaced, ganisation.
all types of puncture, such as cuts you must inform the specialist. The bottle has a limited service
larger than 4 mm, or cuts in tyre life which is indicated on its label.
When driving, vibration may be felt
sidewall B. Check the expiry date.
due to the presence of the repair
Ensure also that the wheel rim is in product injected into the tyre. Contact an approved dealer to re-
good condition. place the inflation tube and repair
Do not pull out the foreign body product bottle.
causing the puncture if it is still in
the tyre.
5.3
TYRE PRESSURE KIT (2/3)
With the engine running and the press switch 4 to inflate the tyre to
parking brake applied, the recommended pressure (please
unroll the hose from the container; refer to the information in the section
8 1 on Tyre pressure);
connect the compressor hose 3 to
the containers inlet 8; after a maximum of 15 minutes, stop
depending on the vehicle, connect inflating and read the pressure (on
2 the container 8 to the compressor pressure gauge 5).
from the container recess 7; Note: while the container is empty-
ing (approximately 30 seconds), the
7 unscrew the valve cap on the rele-
pressure gauge 5 will briefly indicate
vant wheel and screw on the con-
tainers inflation adapter 1; a pressure of up to 6 bar. The pres-
6 sure will then drop.
disconnect any accessories previ-
5 3 ously connected to the vehicles ac- adjust the pressure: to increase
4 it, continue inflation with the kit; to
cessories sockets;
adapter 2 must be connected to the reduce it, press button 6.
vehicle accessories socket;
Depending on the vehicle, in the event
of a puncture, use the kit located in the
boot or underneath the luggage com-
partment carpet.
Vehicle fitted with a tyre pressure
loss warning system
If under-inflated (puncture, low pres-
If the vehicle is parked on
sure, etc.), the warning light
lights up on the instrument panel. See
Before using this kit, park the hard shoulder, you must
warn other road users of
the vehicle at a sufficient
Tyre pressure loss warning in Section your vehicles presence
distance from traffic, switch
2. with a warning triangle or with other
on the hazard warning
lights, apply the handbrake, ask all devices as per the legislation apply-
passengers to leave the vehicle and ing to the country you are in.
keep them away from traffic.
5.4
TYRE PRESSURE KIT (3/3)
Once the tyre is correctly inflated, Precautions when using the
remove the kit: slowly unscrew the in- kit
flation adapter 1 to prevent any repair
1 product from escaping and store the The kit should not be operated for more
container in plastic packaging to pre- than 15 consecutive minutes.
vent the product from escaping.
Please be aware that a
Affix the driving recommendation poorly tightened or miss-
label to the dashboard where it can ing valve cap can make the
easily be seen by the driver; tyres less airtight and may
Put the kit away. lead to pressure loss.
At the end of this initial inflation op-
eration, air will still escape from the Always use valve caps identical to
tyre. You must drive a short distance those fitted originally and tighten
in order to seal the hole. them fully.
Start immediately and drive at
between 12 and 40 mph (20 and
If a minimum pressure of 1.8 bar is 60 km/h) in order to distribute the
not reached after 15 minutes, repair product evenly in the tyre and, after
is not possible; do not drive the ve- driving for 2 miles (3 km), stop and
hicle but contact an approved dealer. check the pressure. Following repair with the kit,
If the pressure is greater than do not travel further than
1.3 bar but less than the recom- 120 miles (200 km). In addi-
mended pressure (refer to the label tion, reduce your speed and
affixed to the edge of the drivers under no circumstances exceed
door), readjust it. Otherwise, please 48 mph (80 km/h). The sticker,
contact an authorised dealer: the which you must affix in a prominent
Nothing should be placed tyre cannot be repaired. position on the dashboard, reminds
around the drivers feet you of this.
as such objects may slide Depending on the country or local
under the pedals during legislation, a tyre repaired with the
sudden braking manoeuvres and inflation kit may need to be replaced.
obstruct their use.
5.5
TOOLS
2 Jack 2
Fold it correctly before refitting it in its
1 housing (ensure that the wheelbrace is
correctly positioned).
Hubcap tool 3
This tool is used to remove the wheel
6 trims.
3
A
Wheel bolt guide 4
4 To finish loosening or starting to tighten
the wheel bolts.
5
Tow eye 5
The tools included in the tool kit depend Storage bag Please see Towing: breakdown recov-
on the vehicle. Supplied with the tool kit, this allows ery in Section 5.
Tool kit A is located in the tray under you to store a punctured wheel in the
the luggage compartment carpet. boot.
Lift the cover and remove it. Lever 6
This tightens or releases the tow eye 5.
Wheelbrace 1
Wheel bolt bag Locks or unlocks the wheel bolts and
tow eye 5.
Do not leave the tools unsecured inside the vehicle as they may come loose under braking. After use, check that all the
tools are correctly clipped into the tool kit, then position it correctly in its housing: there is a risk of injury.
If wheel bolts are supplied in the tool kit, only use these bolts for the emergency spare wheel: refer to the label affixed
to the emergency spare wheel.
The jack is designed for wheel changing purposes only. Under no circumstances should it be used for carrying out repairs un-
derneath the vehicle or to gain access to the underside of the vehicle.
5.6
WHEEL TRIMS - WHEEL
B
C
2
5.7
CHANGING A WHEEL (1/2)
Vehicles equipped with a jack Continue to crank the jack so that the
and wheelbrace baseplate is correctly positioned (it
should be underneath the vehicle and
1 If necessary, remove the wheel trim. aligned with the jack head).
Use the wheelbrace 1 to slacken off the Turn it a few times to lift the wheel off
wheel bolts. Position it so as to be able the ground.
to push from above.
Crank up jack 2 by hand to position the
3 jack head against the jacking point clos-
est to the relevant wheel and marked
2 by an arrow 3.
5.8
CHANGING A WHEEL (2/2)
Undo the bolts and take off the wheel. Vehicle fitted with a tyre pressure
Fit the emergency spare wheel on the loss warning system
central hub and turn it to locate the If under-inflated (puncture, low pres-
mounting holes in the wheel and the
hub. sure, etc.), the warning light
on
the instrument panel comes on. See
Tighten the bolts, checking that the Tyre pressure loss warning in
wheel is correctly positioned on its hub. Section 2.
Lower the jack.
With the wheel on the ground, tighten
the bolts fully and have the tightness of
the bolts checked and the emergency
spare wheel pressure checked as soon Do not leave the tools un-
as possible. secured inside the vehicle
as they may come loose
under braking. After use,
check that all the tools are correctly
clipped into the tool kit, then posi-
tion it correctly in its housing: risk of
injury.
If wheel bolts are supplied in the
tool kit, only use these bolts for the
emergency spare wheel: refer to the
label affixed to the emergency spare
wheel.
If you have a puncture, re- The jack is designed for wheel
place the wheel as soon as changing purposes only. Under no
possible. circumstances should it be used for
carrying out repairs underneath the
A tyre which has been punc- vehicle or to gain access to the un-
tured should always be inspected derside of the vehicle.
(and repaired, where possible) by a
specialist.
5.9
TYRES (1/3)
Tyre and wheel safety When the tyre tread has been worn
The tyres are the only contact between to the level of the warning strips, they
the vehicle and the road, so it is essen- become visible 2: it is then neces-
tial to keep them in good condition. You sary to replace your tyres because the
must make sure that your tyres con- - 2 tread rubber is now only 1.6 mm deep
form to local road traffic regulations. at most, resulting in poor road hold-
ing on wet roads.
An overloaded vehicle, long journeys
by motorway, particularly in very hot
For your safety, please re- 1 weather, or continual driving on poorly
spect the speed limit. surfaced minor roads will lead to more
rapid tyre wear and affect safety.
When they need to be re-
placed, only tyres of the
same make, size, type and profile
should be used on a single axle.
They must: either have a load ca- Maintaining the tyres
pacity and a speed capacity at The tyres must be in good condition
least equal to the original tyres, and the tread form must have sufficient
or correspond to those recom- depth; tyres approved by our Technical
mended by your authorised Department have wear warning strips
dealer. 1 which are indicators moulded into
Failure to heed these instructions the tread at several points.
could endanger your safety and
affect your vehicles roadworthi- Incidents which occur when
ness. driving, such as striking the
Risk of loss of control of the ve- kerb, may damage the tyres
hicle. and wheel rims, and could
also lead to misalignment of the
front or rear axle geometry. In this
case, have the condition of these
checked by an approved dealer.
5.10
TYRES (2/3)
Tyre pressures Pressures should be checked when the Vehicle fitted with a tyre pressure
tyres are cold; ignore higher pressures loss warning system
Adhere to the tyre pressures (including which may be reached in hot weather
the emergency spare wheel). The tyre If under-inflated (puncture, low pres-
or following a fast journey.
pressures should be checked at least
once a month and additionally before If tyre pressures cannot be checked
sure, etc.), the warning light
the instrument panel comes on. See
on
any long journey (refer to the label af- when the tyres are cold, assume an in-
fixed to the edge of the drivers door). crease of 0.2 to 0.3 bar (or 3 PSI). Tyre pressure loss warning in chap-
ter 2.
Never deflate a hot tyre.
5.11
TYRES (3/3)
Emergency spare wheel Use in winter Snow or Winter tyres
Refer to the information on the We would recommend that these be
Chains fitted to all four wheels to ensure that
Emergency spare wheel and in-
structions on Changing a wheel in For safety reasons, fitting snow your vehicle retains maximum adhe-
Section 5. chains to the rear axle is strictly for- sion.
bidden. Warning: These tyres sometimes have
Changing wheels around Chains cannot be fitted to tyres which a specific direction of rotation and a
are larger than those originally fitted to maximum speed index which may be
This practice is not recommended. the vehicle. lower than the maximum speed of your
vehicle.
Fitting new tyres Studded tyres
This type of equipment may only be
used for a limited period and as laid
down by local legislation. It is neces-
sary to observe the speed specified by
Chains may only be fitted current legislation.
For safety reasons, this op- to tyres of the same size These tyres must, at a minimum, be
eration must be carried out as those originally fitted to fitted to the two front wheels.
by a specialist. your vehicle.
Fitting different tyres may
change your vehicle as follows:
it may mean that your vehicle no
longer conforms to current regu-
lations;
17 wheels cannot be
it may change the way it handles fitted with chains.
when cornering;
If you wish to fit snow In all cases, we would recommend
it may cause the steering to be chains, you must use spe- that you contact an approved dealer
heavy; cial equipment. who will be able to advise you on
it may affect the use of snow Consult an approved Dealer. the choice of equipment which is
chains. most suitable for your vehicle.
5.12
FRONT HEADLIGHTS: changing bulbs (1/3)
Main beam headlight
To change the bulb:
1 remove cover B;
2 disconnect the wiring 4 (black lead);
unclip the spring 3 and remove the
3 bulb.
B
A Bulb type: H1.
5 It is essential to use anti-U.V. 55W
4 bulbs so as not to damage the plastic
on the headlights.
Do not touch the bulb glass. Hold it
by its base.
When the bulb has been changed,
make sure you refit the cover correctly.
Direction indicator lights Dipped beam headlight
Turn the bulb holder 1 a quarter of a To change the bulb:
turn and take out the bulb. remove cover A;
Bulb type: PY21W. disconnect the wiring 5 (black lead);
Once the bulb has been replaced, unclip the spring 2 and remove the
bulb. The bulbs are under pres-
check that it is properly secured. sure and can break when
Bulb type: H1. replaced.
Risk of injury.
5.13
FRONT HEADLIGHTS: changing bulbs (2/3)
5.14
FRONT HEADLIGHTS: changing bulbs (3/3)
Additional lights
If you wish to fit fog lights to your ve-
hicle, please see an authorised dealer.
5.15
REAR AND SIDE LIGHTS: changing bulbs (1/2)
A 2 4
1
3
Side lights/brake and Pull on the outside A of the light and 4 Side light and brake light
direction indicator lights remove the rear light unit. Bulb type: P21/5W.
Open the boot lid and remove screws 1. Remove the bulb holder by releasing 5 Direction indicator lights
clip 2, then clips 3. Bulb type: PY21.
Change the bulb.
Refit the bulb holder and push the unit
in fully until it locks in place.
Check that the light is properly locked
in position.
Tighten screws 1.
5.16
REAR AND SIDE LIGHTS: changing bulbs (2/2)
9 10
5.17
INTERIOR LIGHTING: changing bulbs (1/2)
5.18
INTERIOR LIGHTING: changing bulbs (2/2)
3
5
5.19
RENAULT CARD: battery
2 A
B
4
1 3
Replacing the battery When refitting, proceed in the reverse Operating faults
When the message KEYCARD order, then press one of the buttons on If the battery is too weak to ensure cor-
BATTERY LOW appears on the in- the card four times, close to the vehicle: rect operation, you can still start (insert
strument panel, replace the RENAULT the next time the vehicle is started, the the RENAULT card in the card reader)
card battery, press button 1 pulling message will disappear. and lock/unlock the vehicle (refer to the
on emergency key 2, then unclip the Note: it is not advisable to touch the information on "Locking/unlocking the
cover 3 using tab 4. electronic circuit or contacts on the doors" in Section 1).
Remove the battery by pressing on one RENAULT card when replacing the bat-
side (movement A) and by lifting the tery.
other (movement B) then replace it, en-
suring the polarity and model, shown
on cover 3 are respected.
Check that the cover is clipped shut.
Do not throw away your
used batteries; give them to
an organisation responsible
The batteries are available from approved Dealers, and their service life approxi- for collecting and recycling
mately two years. Check that there is no dye on the battery: risk of an incorrect batteries.
electrical contact.
5.20
FUSES (1/3)
1 B
Check the fuse in question and replace it, if necessary, by a fuse of the
same rating.
To comply with current legislation, or
If a fuse is fitted with too high a rating, it may cause the electrical circuit
as a precaution, you can obtain an
to overheat (risk of fire) in the event of an item of equipment using an ex-
emergency kit from your approved
cessive amount of current.
dealer containing a set of spare
bulbs and fuses.
5.21
FUSES (2/3)
Allocation of fuses
(the presence of certain fuse depends on the vehicle equipment level)
37
1 2 3 4 5 6 7
38
8 9 10 11 12 13 14
39
15 16 17 18 19 20 21 22 23
24 25 26 27 28 29 30 31 32
33
34
35
36
5.22
FUSES (3/3)
5.23
BATTERY: breakdown recovery (1/2)
To avoid all risk of sparks: Connecting a battery charger
Ensure that any electrical consumers The battery charger must be com-
(courtesy lights, etc.) are switched patible with a battery with nominal
off before disconnecting or recon- voltage of 12 volts.
necting the battery. Do not disconnect the battery when the
When charging, stop the charger engine is running. Follow the instruc-
before connecting or disconnecting tions given by the manufacturer of
the battery. the battery charger you are using.
Do not place metal objects on the
battery to avoid creating a short cir-
cuit between the terminals.
Always wait at least one minute after
the engine has been switched off Handle the battery with care
before disconnecting a battery. as it contains sulphuric acid,
which must not come into
Make sure that you reconnect the contact with eyes or skin. If
battery terminals after refitting. it does, wash the affected area with
plenty of cold water. If necessary,
consult a doctor.
Ensure that naked flames, red hot
Special procedures may be objects and sparks do not come into
required to charge some contact with the battery as there is a
batteries. Contact your ap- risk of explosion.
Before performing any proved dealer. The engine may be hot when car-
action in the engine com-
Avoid all risk of sparks which may rying out operations in close prox-
partment, the ignition must
cause an immediate explosion, and imity. In addition, the engine cooling
be switched off by pressing
charge the battery in a well-venti- fan can come on at any moment.
the engine stop button (please see
the information on Starting, stop- lated area. Risk of serious injury. Risk of injury.
ping the engine in Section 2).
5.24
BATTERY: breakdown recovery (2/2)
Starting the vehicle using the
battery from another vehicle
1 2
If you have to use the battery from an- 2
other vehicle to start, obtain suitable
jump leads (with a large cross section)
from an approved dealer or, if you al- B
ready have jump leads, ensure that A
they are in perfect condition.
The two batteries must have an iden- 1
tical nominal voltage of 12 volts. The
battery supplying the current should
have a capacity (amp-hours, Ah) which
is at least the same as that of the dis-
4
charged battery. 3
Ensure that there is no risk of contact Depending on the vehicle, unclip the
between the two vehicles (risk of short battery cover.
circuiting when the positive terminals
are connected) and that the discharged Connect the positive cable A to the
battery is properly connected. Switch support on the (+) terminal1, then to the
off your vehicle ignition. (+) terminal 4 of the battery supplying
the current.
Start the engine of the vehicle supply-
ing the current and run it at an interme- Connect the negative cable B to the ()
diate engine speed. terminal 3 of the battery supplying the Check that there is no con-
current and then to the () terminal 2 of tact between leads A and B
the discharged battery. and that the positive lead A
is not touching any metal
Start the engine, and as soon as it starts parts on the vehicle supplying the
running, disconnect cables A and B in current.
reverse order ( 2 - 3 - 4 - 1 ).
Risk of injury and/or damage to the
vehicle.
5.25
FITTING A RADIO
5.26
ACCESSORIES
5.27
WINDSCREEN WIPER BLADES (1/2)
5.28
WINDSCREEN WIPER BLADES (2/2)
To refit
5 To refit the wiper blade, proceed in re-
verse order to removal. Make sure that
the blade is correctly locked in position.
5.29
TOWING: breakdown recovery (1/2)
Before towing, unlock the steering The speed specified by current legis-
column: with the clutch depressed, lation for towing must always be ob-
engage first gear (lever in position N served. If your vehicle is the towing 2
or R for vehicles with automatic gear- vehicle, do not exceed the maximum
boxes), insert the RENAULT card in the towing weight for your vehicle (refer to 1
card reader, then press the engine start the information on Weights in Section
button for two seconds. 6).
Reposition the lever to neutral (posi-
tion N for vehicles fitted with an auto- Towing a vehicle with an
matic gearbox). automatic gearbox
The column is unlocked, the acces- With the engine switched off, the trans-
sory functions are supplied: the vehi- mission is no longer lubricated. It is
cle lights can be used (indicators, brake preferable to tow this type of vehicle on
lights etc.). At night the vehicle must a trailer or tow it with the front wheels
have its lights on. off the ground.
Once you have finished towing, press If the lever is stuck in P, even though
Under exceptional circumstances, you you are depressing the brake pedal, the
the engine start button twice (risk of may tow the vehicle with all four wheels
running down the battery). lever can be released manually. To do
on the ground, only going forward, with this, unclip the base of the lever, then
the gear lever in the neutral N position, insert a tool (with a hard rod to it) into
and for a distance not exceeding the slot 1 and press the button 2 at the
30 miles (50 km). same time in order to unlock the lever.
Contact an authorised dealer as soon
as possible.
5.30
TOWING: breakdown recovery (2/2)
5.31
OPERATING FAULTS (1/6)
The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact
an approved Dealer as soon as possible.
The RENAULT card does not lock or Card battery is flat. Replace the battery. You can still lock/
unlock the doors. unlock and start your vehicle (refer to the in-
formation on Locking, unlocking the open-
ing elements in Section 1 and Starting,
stopping the engine in Section 2).
Use of appliances operating on the Stop using the equipment or use the in-
same frequency as the card (mobile tegrated key (refer to the information on
phone, etc.). Locking, unlocking the opening elements
in Section 1).
Vehicle located in a high electromag- Use the key integrated in the card (refer to
netic radiation zone. the information on Locking, unlocking the
Vehicle battery flat. opening elements in Section 1).
The vehicle is started. With the engine running, the cards locking/
unlocking device is blocked. Turn off the ig-
nition.
5.32
OPERATING FAULTS (2/6)
The starter is activated POSSIBLE CAUSES WHAT TO DO
The instrument panel indicator lights are Battery terminals not tight, Retighten or reconnect the terminals, or clean them if
weak or fail to light up and the starter battery terminals discon- they are oxidised.
does not turn. nected or oxidised.
Discharged battery or not Connect another battery to the faulty battery. Refer to
operational. information on Battery: troubleshooting in Section 5
or replace the battery if necessary.
Do not push the vehicle if the steering column is
locked.
The engine will not start. Starting conditions are not Please refer to the information on Starting, stopping
fulfilled. the engine in Section 2.
The RENAULT hands-free Insert the card in the card reader in order to start the
card does not work. engine.
Please refer to the information on Starting, stopping
the engine in Section 2.
The engine cannot be switched off. Card not detected. Insert the card in card reader.
The steering column remains locked. Steering wheel locked. Move the steering wheel while pressing the engine
start button (please refer to Section 2 Starting, stop-
ping the engine).
5.33
OPERATING FAULTS (3/6)
Vibrations. Tyres not inflated to correct pres- Check the tyre pressures: if this is not the
sures, incorrectly balanced or dam- problem, have them checked by an ap-
aged. proved Dealer.
White smoke from the exhaust. In the diesel version, this is necessar- Please refer to the information on Special
ily a fault. Smoke may be caused by features of diesel versions in Section 2.
particle filter regeneration.
Smoke under the bonnet. Short-circuit or cooling system leak. Stop, switch off the ignition, stand away
from the vehicle and contact an approved
dealer.
while cornering or braking The level is too low. Top up the engine oil level (refer to the in-
formation on Engine oil level: topping up,
filling in Section 4).
is slow to go out or remains lit Loss of oil pressure. Stop the vehicle and contact an approved
under acceleration Dealer.
5.34
OPERATING FAULTS (4/6)
The engine is overheating. The cool- Engine cooling fan not working. Stop the vehicle, switch off the engine and
ant temperature indicator is in the contact an approved dealer.
warning zone and warning light
comes on.
Coolant boiling in the coolant reser- Mechanical fault: damaged cylinder Stop the engine.
voir. head gasket. Contact an approved dealer.
Radiator: If there is a significant lack of coolant, remember that it must never be topped up using cold coolant while
the engine is very warm. After any procedure on the vehicle which has involved even partial draining of the cooling
system, it must be refilled with a new mixture prepared in the correct proportions. Reminder: only products approved
by our Technical Department may be used for this purpose.
5.35
OPERATING FAULTS (5/6)
Electrical equipment POSSIBLE CAUSES WHAT TO DO
The wipers do not work. Wiper blades stuck. Free the blades before using the wipers.
Direction indicators flashing more Blown bulb. See information on Headlights: changing
quickly. bulbs or Rear and side lights: changing
bulbs.
The direction indicators do not work. Faulty electrical circuit or control. Consult an approved dealer.
5.36
OPERATING FAULTS (6/6)
Electrical equipment POSSIBLE CAUSES WHAT TO DO
Traces of condensation in the lights. Traces of condensation may be a nat-
ural phenomenon caused by varia-
tions in temperature.
In this case, the traces will disappear
slowly once the lights are switched
on.
The front seat belt reminder light An object is stuck between the floor Remove all objects from underneath the
comes on when the seat belts are and the seat and is disrupting the op- front seats.
fastened. eration of the sensor.
5.37
5.38
Section 6: Technical specifications
A
1
2
3
4
5
A 10 6
9 7
8
6.2
ENGINE IDENTIFICATION PLATES
1 2
3 A
1 Engine type.
2 Engine suffix.
3 Engine number.
6.3
DIMENSIONS (in metres)
1,579*
1,516
1,957
* unladen
6.4
ENGINE SPECIFICATIONS
Engine type
H4B Turbo H5F Turbo K9K Turbo
(see engine plate)
It is essential that you use unleaded petrol of the octane rating stated on the Diesel: the label located
Type of fuel
label inside the fuel filler flap. in the fuel filler flap
Octane rating
indicates authorised fuels.
Spark plugs Only use the spark plugs specified for your vehicles engine.
The type should be marked on a label affixed inside the engine compartment.
If it is not then contact an approved Dealer.
Fitting spark plugs other than those specified may damage the engine.
6.5
WEIGHTS (in kg)
The weights indicated for a basic vehicle without options: they vary depending on the your vehicles equipment. Consult
your approved Dealer.
6.6
REPLACEMENT PARTS AND REPAIRS
Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same
level of quality as the parts fitted originally.
If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out
within the manufacturers Network using original parts are guaranteed according to the conditions set out on the reverse of the
repair order.
6.7
SERVICE SHEETS (1/6)
VIN: ..................................................................................
6.8
SERVICE SHEETS (2/6)
VIN: ..................................................................................
6.9
SERVICE SHEETS (3/6)
VIN: ..................................................................................
6.10
SERVICE SHEETS (4/6)
VIN: ..................................................................................
6.11
SERVICE SHEETS (5/6)
VIN: ..................................................................................
6.12
SERVICE SHEETS (6/6)
VIN: ..................................................................................
6.13
ANTICORROSION CHECK (1/5)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Date of repair:
Date of repair:
Date of repair:
6.14
ANTICORROSION CHECK (2/5)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Date of repair:
Date of repair:
Date of repair:
6.15
ANTICORROSION CHECK (3/5)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Date of repair:
Date of repair:
Date of repair:
6.16
ANTICORROSION CHECK (4/5)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Date of repair:
Date of repair:
Date of repair:
6.17
ANTICORROSION CHECK (5/5)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Date of repair:
Date of repair:
Date of repair:
6.18
ALPHABETICAL INDEX (1/5)
A C
ABS ..............................................................1.46, 2.27 2.31 catalytic converter................................................... 2.10 2.11
accessories........................................................................ 5.27 central door locking ........................... 1.5 1.10, 1.13 1.15
accessories socket ............................................................ 3.20 changing a bulb .....................................................5.13 5.19
additional methods of restraint .......................................... 1.27 changing a wheel........................................................ 5.8 5.9
side protection ............................................................. 1.26 changing gear ...............................................2.12, 2.43 2.45
to the front seat belts .......................................1.21 1.24 child restraint/seat .............................1.28 1.29, 1.31 1.37
to the rear seat belts .................................................... 1.25 child safety......1.8 1.9, 1.12, 1.24, 1.28 1.29, 1.31 1.37,
adjusting your driving position ......................1.16 1.20, 3.21 2.3, 3.12 3.13
advice on antipollution ....................................................... 2.18 child seats..........................................1.28 1.29, 1.31 1.36
air bag...........................................................1.21 1.27, 1.44 children ........................ 1.2, 1.8 1.9, 1.28 1.29, 3.12 3.13
activating the front passenger air bags ........................ 1.39 children (safety) .......................................................... 1.2, 1.12
deactivating the front passenger air bags .................... 1.37 cigar lighter ........................................................................ 3.20
air conditioning ........................................................3.4 3.11 cleaning:
air vents ...................................................................... 3.2 3.3 inside the vehicle .............................................. 4.15 4.16
anti-corrosion check ..............................................6.14 6.18 clock ....................................................................... 1.62 1.63
anti-corrosion protection .................................................... 4.13 closing the doors ...................................................1.11 1.15
anti-lock braking system: ABS ...............................2.27 2.31 control instruments ............................1.44 1.52, 1.62 1.63
antipollution controls ..................................................................1.40 1.43
advice .......................................................................... 2.18 courtesy light ............................................................ 3.14, 5.18
armrest: courtesy mirrors ................................................................. 3.19
front .............................................................................. 3.16 cruise control ................................................1.47, 2.35 2.38
ashtray ............................................................................... 3.20 cruise control-speed limiter....................................2.32 2.38
ASR (traction control) ............................................2.27 2.31
audible and visual signals.................................................. 1.68 D
automatic gearbox (use) ........................................2.43 2.45 dashboard..............................................................1.40 1.43
automatic gearbox selector lever...........................2.43 2.45 deadlocking the doors ....................................................... 1.10
demisting
B rear screen ..................................................3.4, 3.7 3.10
battery............................................................ 4.12, 5.24 5.25 windscreen ..................................................3.5, 3.7 3.10
troubleshooting ................................................. 5.24 5.25 dimensions .......................................................................... 6.4
bonnet......................................................................... 4.2 4.3 dipstick................................................................................. 4.4
brake fluid ............................................................................ 4.8 display ...................................................................1.44 1.50
bulbs doors/tailgate ...........................................................1.2 1.15
changing ..........................................................5.13 5.19 driver assistance....................................................2.27 2.42
drivers position .....................................................1.40 1.48
7.1
ALPHABETICAL INDEX (2/5)
driving ........2.2 2.5, 2.10 2.11, 2.13 2.17, 2.20 2.26, passenger compartment filter ........................................ 4.9
2.24 2.40, 2.43 2.45 fitting a radio ...................................................................... 5.26
driving aids ............................................................2.27 2.42 fittings ....................................................................3.15 3.19
driving position front passenger air bag deactivation ................................. 1.37
settings ............................................................1.18 1.20 front seat adjustment ......................................................... 1.17
driving recommendations ......................................2.13 2.17 front seats .......................................................................... 4.17
adjustment .......................................................1.16 1.18
E fuel
ECO driving ...........................................................2.13 2.17 advice on fuel economy ...................................2.13 2.17
ECO mode ......................................................................... 2.15 consumption ....................................................2.13 2.17
electric beam height adjustment ............................. 1.69 1.70 filling ........................................................1.44, 1.74 1.76
electric windows ..................................................... 3.12 3.13 grade ................................................................1.74 1.76
electronic stability control: ESC .............................2.27 2.31 fuel consumption ...................................................2.13 2.17
emergency brake assist.........................................2.27 2.31 fuel economy .........................................................2.13 2.17
emergency braking ................................................2.27 2.31 fuel filler cap ..........................................................1.74 1.76
emergency key ..........................................................1.2 1.4 fuel level ................................................................1.44 1.49
emergency spare wheel ...................................................... 5.2 fuel tank
engine capacity ........................................................................ 1.74
technical specifications .................................................. 6.5 fuel tank capacity ...................................................1.74 1.76
engine coolant ..................................................................... 4.7 fuses ......................................................................5.21 5.23
engine oil ...................................................................4.4 4.6
engine oil capacity ...................................................... 4.5 4.6 G
engine oil level ...........................................................4.4 4.6 gear lever........................................................................... 2.12
engine specifications .................................................... 6.3, 6.5
engine standby ..........................................................2.6 2.9 H
engine start/stop button .............................................2.3 2.5 handbrake.......................................................................... 2.12
environment ....................................................................... 2.19 hands-free telephone integrated control ............................ 3.31
ESC: electronic stability control ....................1.46, 2.27 2.31 hazard warning lights signal .............................................. 1.68
external temperature ......................................................... 1.63 headlight beam adjustment .................................... 1.69 1.70
headrest.................................................................... 1.16, 3.21
F heated seats ...................................................................... 1.17
faults heated windscreen ..................................................3.7 3.10
operating faults ................................................5.32 5.37 heating and air conditioning system ........................3.4 3.11
filter heating system ........................................................3.4 3.11
air filter ........................................................................... 4.9 Hill Start Assist.......................................................2.27 2.31
oil filter .................................................................. 4.5 4.6 horn ................................................................................... 1.68
7.2
ALPHABETICAL INDEX (3/5)
horn: brake lights ....................................................... 5.16 5.17
flash ............................................................................. 1.68 dipped beam headlights .................1.44, 1.65, 5.13 5.15
hubcap tool ................................................................. 5.6 5.7 direction indicators .........................1.44, 1.68, 5.13 5.16
fog lights .................................................... 1.44, 1.67, 5.17
I hazard warning ............................................................ 1.68
indicators ......................................................1.68, 5.13 5.17 main beam headlights ................................ 1.44, 1.65, 5.13
indicators: reversing lights ............................................................. 5.17
direction indicators ....................................................... 1.68 side lights ................................................1.65, 5.13 5.16
instrument panel ..............................................1.44 1.52 load permitted on the roof.................................................... 6.6
instrument panel ....................................................1.44 1.60 locking the doors .....................................................1.2 1.15
instrument panel messages...................................1.51 1.60
interior trim M
maintenance ..................................................... 4.15 4.16 maintenance ...................................................................... 2.18
Isofix ....................................................................... 1.31 1.32 maintenance:
bodywork .......................................................... 4.13 4.14
J interior trim ........................................................ 4.15 4.16
jack ...................................................................................... 5.6 mechanical .........................................4.4, 4.12, 6.8 6.13
map reading lights ............................................................. 3.14
L methods of restraint in addition to the seat belts ...1.21 1.27
levels .........................................................................4.7 4.9 mobile floor ........................................................................ 3.26
levels: multimedia equipment .............................................. 3.31, 5.26
brake fluid ...................................................................... 4.8
coolant ........................................................................... 4.7 N
windscreen washer reservoir ......................................... 4.9 navigation system .............................................................. 3.31
lifting the vehicle
changing a wheel .................................................. 5.8 5.9 O
lighting: oil change ................................................................... 4.5 4.6
exterior .............................................................1.65 1.70 opening the doors ..................................................1.11 1.14
instrument panel .......................................................... 1.65 operating faults ................................ 1.44 1.48, 5.32 5.37
interior ...................................................... 3.14, 5.18 5.19
lights P
adjustment ........................................................ 1.69 1.70 paintwork
changing bulbs .................................................5.13 5.15 maintenance ..................................................... 4.13 4.14
front ..................................................................5.13 5.15 parking distance control.......................................... 2.39 2.40
lights: power-assisted steering..................................................... 1.61
adjusting ........................................................... 1.69 1.70 pretensioners .........................................................1.21 1.24
7.3
ALPHABETICAL INDEX (4/5)
puncture........................................................ 5.2, 5.6, 5.8 5.9 special features of diesel versions..................................... 2.11
special features of petrol vehicles ..................................... 2.10
R speed limiter .................................................1.47, 2.32 2.34
radio................................................................................... 3.31 starting the engine .....................................................2.3 2.9
rear bench seat................................... 3.22 3.23, 4.20 4.21 steering wheel
rear parcel shelf ................................................................. 3.25 adjustment ................................................................... 1.61
rear seat ................................................................. 4.20 4.21 Stop & Start ......................................................1.47, 2.6 2.9
rear seats........................................................................... 1.20 Stop & Start function..................................................2.6 2.9
functions ........................................................... 3.22 3.23 stopping the engine ...................................................2.3 2.5
rear view camera .................................................... 2.41 2.42 storage compartment.............................................3.15 3.19
rear view mirrors ................................................................ 1.64 storage compartments ...........................................3.15 3.19
RENAULT ANTI-INTRUDER DEVICE (RAID) ................... 1.15 sun visor ............................................................................ 3.19
RENAULT card switching on the vehicle ignition ................................2.3 2.5
battery .......................................................................... 5.20
use ................................................... 1.2 1.10, 2.3 2.5 T
RENAULT card battery ...................................................... 5.20 tailgate ..........................................................3.24, 3.26 3.28
replacement parts ................................................................ 6.7 tanks and reservoirs
reverse gear brake fluid ...................................................................... 4.8
selecting ..................................................2.12, 2.43 2.45 coolant ........................................................................... 4.7
reversing sensor ..................................................... 2.39 2.40 tanks and reservoirs:
roof bars ............................................................................ 3.30 windscreen washer ........................................................ 4.9
roof rack technical specifications ..............................................6.4 6.7
roof bars ....................................................................... 3.30 telephone ........................................................................... 3.31
running in ............................................................................. 2.2 temperature regulation ............................................3.7 3.11
tool kit .................................................................................. 5.6
S towing
seat belt pretensioners breakdown ........................................................ 5.30 5.31
front seat belt ...................................................1.21 1.24 towing equipment ......................................................... 3.29
seat belts ......................................................1.18 1.24, 1.27 towing a caravan ........................................................ 3.29, 6.6
seat trim .................................................................4.17 4.21 towing equipment
seats: trim ..............................................................4.17 4.21 fitting ............................................................................ 3.29
service sheets..........................................................6.8 6.13 towing hitch...................................................... 5.6, 5.30 5.31
side protection devices ...................................................... 1.26 towing rings ....................................................................... 3.28
signals and lights ...................................................1.65 1.70 towing weights ..................................................................... 6.6
speakers traction control: ASR ..............................................2.27 2.31
location ........................................................................ 5.26 transporting children ..........................1.28 1.29, 1.31 1.37
7.4
ALPHABETICAL INDEX (5/5)
transporting objects
in the luggage compartment ........................................ 3.28
on the roof ...................................................................... 6.6
trims ..................................................................................... 5.7
trip computer and warning system... 1.44 1.48, 1.51 1.60
tyre inflation kit...........................................................5.3 5.5
tyre pressure....... 2.20 2.26, 2.24 2.26, 4.10 4.11, 5.11
tyre pressure loss warning............... 2.20 2.26, 2.24 2.26
tyre pressures ......................................................... 4.10 4.11
tyres2.17, 2.20 2.26, 2.24 2.26, 4.10 4.11, 5.10 5.12
U
unlocking the doors ................................................ 1.13 1.14
V
variable power-assisted steering ....................................... 1.61
vehicle identification plates .................................................. 6.3
ventilation ................................................................3.2 3.11
W
warning lights.........................................................1.44 1.60
washing .................................................................. 4.13 4.14
weights ................................................................................ 6.6
wheelbrace .......................................................................... 5.6
wheels (safety) ......................................................5.10 5.12
windscreen de-icing/demisting ................................3.7 3.10
windscreen washer ................................................1.71 1.73
wiper blades ........................................................... 5.28 5.29
wipers ....................................................................1.71 1.73
blades ............................................................... 5.28 5.29
7.5
7.6
RENAULT S.A.S. SOCIT PAR ACTIONS SIMPLIFIE AU CAPITAL DE 533 941 113 / 13-15, QUAI LE GALLO
92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 SIRET 780 129 987 03591 / TL. : 0810 40 50 60
NU 1007-7 99 91 098 39R 10/2015 Edition anglaise