Auto Washer
Model: DWF-111W/B
DWF-200W
DWF-260W
Caution:
In this Manual, some parts can be changed for imroving, their
performance without notice in the parts list. So, if you need the
latest parts information, please refer to PPL(Parts Price List) in
Service Information Center http://svc.dwe.co.kr).
AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO
WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER
AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO
WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER
AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO
WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER
AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO
WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER
Contents
1. SPECIFICATIONS................................................................................................................... 2
WASHING MACHINE
APPENDIX
WIRING DIAGRAM ....................................................................................................................... 28
PARTS DIAGRAM ......................................................................................................................... 33
PARTS LIST................................................................................................................................... 37
CIRCUIT DIAGRAM ...................................................................................................................... 41
1. SPECIFICATIONS
89L 93L
MEDIUM 78 L MEDIUM 83 L
7 WATER LEVEL SELECTOR
67L 72L
LOW 56 L LOW 61 L
E.LOW 45 L E.LOW 50 L
REVOLUTION 50Hz WASH : 125 - 140 RPM, SPIN : 640 - 675 RPM
9 PER MINUTE
60Hz WASH : 130 - 150 RPM, SPIN : 710 -740 RPM
13 LINT FILTER O
15 ALARM SIGNAL O
2 SPECIFICATIONS
2. STRUCTURE OF THE WASHING MACHINE
The parts and features of your washer are illustrated on this page.
Become familiar with all parts and features before using your washer.
NOTE
The drawings in this book may vary from your washer model.
They are designed to show the different features of all models covered by this book,
Your model may not include all features.
CASE DETERGENT
AND SOFTENER
LINT FILTER(2EA)
PULSATOR
CONTROL PANEL
POWER CORD
HOSE DRAIN
ADJUSTABLE LEG
DRYTEN [OPTION] COVER UNDER (OPTION) WATER TAP ADAPTER INLET HOSE
DRYTEN
U
P
HOSE DRAIN [FOR PUMP] HOSE DRAIN[FOR NONPUMP] CONNECTOR INLET [OPTION]
STRUCTURE 3
3. DIRECTIONS FOR INSTALLATION AND USE
Installing Place
1 Hor zon
Sett ng 2 Check the Hor zon
Status
A er con ro ng he he gh Check he pos on o ub above
by urn ng he ad us ab e he cen er o he washer
eg e he washer pu
down o he ground
NOTES
4 DIRECTIONS
How to Connect the Inlet Hose
Be careful not to mistake in supplying between the hot(maximum : 50C) and cold water.
In using only one water tap or in case of attached one water inlet valve, connect the inlet hose to the cold water inlet
valve.
Do not over tighten : this could cause damage to couplings.
TAPE
Connector A
Connector B
Please check the rubber packing
inside the inlet hose adapter of
the hose.
Connector
Inlet
Rubber
Connector D Packing Rubber
Connector D Packing
CONNECTION 5
How To Clean The Filter
CLEANING THE LINT FILTER
1 Pull the
power plug
out before
2 Turn off the
water supply
to the washer
3 Pull the
inlet filter out. 4 Remove the dirt
from the inlet filter
with a brush.
cleaning it. and sperate the
inlet hose.
CAP
CONTAINER
FILTER
6 CONVENIENCE
4. FEATURE AND TECHNICAL EXPLANATION
WASH DRAIN SPIN FILL RINSE 1 DRAIN SPIN FILL RINSE 2 DRAIN
MOTOR C.W
SINGAL C.C.W
TIME(SEC.) 0.3 0.3 0.3 0.3 0.3 0.3
35 SEC.
FEATURE 7
Functional Principle of Bubble Washing Machine
ACROSS SECTION
Air bubble
Tub
Outer tub
Pulsator
FUNCTIONAL PRINCIPLE
Bubble Motor supplies the air from the bottom of outer tub to the inner space of pulsator, the air is dispersed by the
rotation of pulsator. Air-bubble is created by the centrifugal force, and rises up.
FUNCTIONAL PRINCIPLE
1 The micom can remember the time from the begining of drain to reset point when the pressure switch reaches to
OFF point
Less than
Continue draining
15 minutes
More than
Program stops and gives the alarm with blinked on display lamp.
15 minutes
8 FEATURE
Automatic Unbalance Adjustment
This system is to prevent abnormal vibration during intermittent spin and spin process.
FUNCTIONAL PRINCIPLE
Contact of safety switch Lid closing
1 When the lid is closed, the safety switch
contact is ON position.
2 In case that wash loads get uneven during
spin, the outer tub hits the safety switch Lid opening
due to the serious vibration, and the spin
process is interrupted.
3 In case that P.C.B. ASSY gets OFF signal
from the safety switch, spin process are
stopped and rinse process is started auto-
Contact lever A
matically by P.C.B. ASSY.
4 If the safety switch is operated due to the Position of Normal (ON)
unbalanced load (OFF)
unbalance of the tub, the program is
stopped and the alarm is given.
NOTES
The alarm finished when you close the lid after opening
it. Check the unbalance of the wash load and the instal-
lation condition.
CIRCULATING-WATER
The washing and rinsing effects have been
Filter
improved by adopting the water system in Tub
which water in the tub is circulated in a
designed pattern.
When the pulsator rotates during the washing Water Outer tub
or rinsing process, the water below the pul- channel
sator fans creates a water currents as shown in Pulsator
figure.
The water is then discharged from the upper
part of the tub through the water channel.
About 40 L/min. water is circulated at the high
water level, standard wash load and standard
water currents.
FEATURE 9
Lint Filter
Much lint may be obtained according to the kind of
clothes to be washed and some of the lint may also
sticks to the clothes.
To minimize this possibility a lint filter is provided on Filter
Filter
the upper part of the tub to filter the wash water as it Bleach
Bleach Inlet
is discharged from the water channel. It is good to Inlet
use the lint filter during washing. Pulsator
Pulsator
Drain Motor
STRUCTURE
Pull
Loosen
Pulley
Lever
Inductive ring
Magnet
Coil of motor
Magnet of motor
FUNCTIONAL PRINCIPLE
1 When the DRAIN MOTOR connected to the power source, the DRAIN MOTOR rotates with 900 r.p.m and
revolves the pulley by gear assembly for reducing.
2 When the pulley is rotated, the pulley winds the wire to open the drain valve.
3 Therefore, rotation of pulley changed to the linear moving of wire.
4 The wire pulls the brake lever of Gear Mechanism Assy within 5 seconds.
5 After the wire pulled, gear assembly is separated from motor and condition of pulling is held by operation of the
lever.
6 When the power is turned off, the drain valve is closed because the wire returns to original position.
10 FEATURE
Gear Mechanism Assy
The proper water currents is made by the rotation of pulsator at a low speed to prevent the damage to the small sized
clothes.
Pulsator Motor
1800 r.p.m (60Hz)
1500 r.p.m (50Hz)
Gear unit as V.BELT
1 revolution
Motor Pulsator
Gear Unit as
Spinner Pulley 125-140r.p.m(60Hz)
710-740r.p.m(60Hz) 130-150r.p.m(50Hz)
5 revolutions 640-675r.p.m(50Hz)
Tub
Gear pulley
710-740r.p.m(60Hz)
Directly
640-675r.p.m(50Hz)
V-belt
FEATURE 11
5. DIRECTIONS FOR DISASSEMBLY AND ADJUSTMENT
BEFORE ATTEMPTING TO SERVICE OR ADJUST ANY PART OF THE WASHING MACHINE, DISCONNECT
THE POWER CORD FROM THE ELECTRIC OUTLET.
1 Raise the top plate on the outer cabinet. 3 Remove the cap pulsator from the pulsator assy by using
2 Loosen four screws mounting outer tub cover and screw driver
remove outer tub cover from the tub assy.
4 Loosen the pulsator mounting screw and remove the pul- 5 Remove the special nut by using T type box wrentch.
sator. 6 Remove the special washer.
12 DIRECTIONS
7 Remove the tub i assy. 8 Lay the front of the washer on the floor.
9 Remove four special bolts of gear protect by using a box
wrentch and remove gear protect.
0 Remove the V-belt.
NOTES
DIRECTIONS 13
MOTOR SYNCHRONOUS AND VALVE REPLACEMENT (NON PUMP MODEL)
1 Lay the front of the washer on the floor. 3 Take out the wire of motor synchronous from the braket.
2 Loosen two special screw of motor synchronous. 4 Separate the motor synchronous from the base.
5 Turn the valve by using screw driver as shown in picture. 6 Remove the valve lid from the valve drain assy.
14 DIRECTIONS
6. THE REPAIR METHOD OF GEAR MECHANISM FOR CLUTCH SPRING PROBLEM
Fixing jig 1
Ratchet handle 1
THE REPAIR 15
How To Check The Clutch Spring Problem
PROBLEM
1) THE LAUNDARY IS IN THE SPIN TUB UNEVENLY WHEN JUST STARTING SPIN PROCESS.
2) THEREFORE, IT CAUSE THE SERIOUS NOISE AND VIBRATION WHEN WASHING AND SPINNING
PROCESS OR SUPPLING WATER IRREGULARY WHEN SPINNING PROCESS
AND CAUSE SHORT OF SPIN PERFORMANCE.
CHECKING METHOD
IN THIS CASE, YOU MUST EMPTY THE SPIN TUB FIRST.
1) TO CHECK THE REVOLUTION OF SPIN TUB. IF THE SPIN TUB DOES NOT REVOLVE AND ONLY
THE PULSATOR IS TURNING, THAT IS CLUTCH SPRING DEFECT.
2) TO CHECK THE SPIN SPEED(RPM) BETWEEN SPIN TUB AND PULSATOR.
IF YOU FIND THE DIFFERENT SPIN SPEED BETWEEN SPIN TUB AND PUSATOR, THIS IS ALSO
CLUTCH SPRING DEFECT.
IN THIS CASE, WE ARE GOING TO SUPPLY THE CLUTCH BOSS ASSEMBLY INSTEAD OF GEAR
MECHANISM ASSEMBLEY. PLEASE REFER TO FOLLOWING FIG.
16 THE REPAIR
The Process Of Disassemble
Disassemble 1
No. Process Notice
THE REPAIR 17
Disassemble 2
No. Process Notice
18 THE REPAIR
The Process Of Assemble
Assemble 1
No. Process Notice
THE REPAIR 19
Assemble 2
No. Process Notice
7
Assemble the protector
20 THE REPAIR
REPLACE THE CASE FILTER ASSY
1 separate the back cover from 2 remove two screws 3 remove three screws
washing machine
4 turn the case filter assy and sepa- 5 separate the drain hose i from the 6 separate the cavitation hose from
rate it from the drain motor case filter assy the case filter assy
7 assemble the case filter assy that 8 tie up three screws 9 tie up two screws
purchased
0 assemble the hose drain I to the q assemble the cavitation hose to w assemble the back cover to the
case filter with bond & clamp the case filter with bond & clamp washing machine
THE REPAIR 21
7. TROUBLE SHOOTING GUIDE
NOTES
1. When replace the P.C.B. ASSY do not scratch the surface of the P.C.B. ASSY.
2. Disconnect the power cord from the electric outlet.
YES
YES
Is the filter of the water
Clean the filter.
inlet valve clogged with
dirt?
NO
YES
YES
NO
Is the output voltage of P.C.B AS is defective. Change the P.C.B AS.
the P.C.B normal?
YES
Lead wire is defective. Change the lead wires.
22 TROUBLE SHOOTING
PROBLEM CHECK POINT CAUSE SOLUTION
Does the water supply YES The water inlet valve is Change the water inlet
continue while the power defective. valve.
is turned off?
NO
Does the water supply YES The triac of P.C.B is
start as soon as you press Change the P.C.B ASSY.
defective.
the power switch?
NO
Operate the washer after
WATER SUP-
setting the water level to
PLY IS NOT HIGH
STOPPED.
NO
Does the water supply Normal operation.
continue after the water
reaches to the HIGH
level?
YES
YES
Is the air tube of water Air tube is defective. Change the air tube.
level switch kinked or
deformed? Pressure switch is defec- Change the pressure
NO
tive. switch.
Concerning Washing
NO YES
NO Normal
THE PUL- Does the motor make
SATOR DOES operating sound?
NOT ROTATE YES NO
EVEN IF THE
Is the motor coil dis- YES
WATER IS Motor is defective. Change the motor.
connected?
SUPPLED.
TROUBLE SHOOTING 23
Concerning Draining
YES
NO
P.C.B ASSY is defective. Change the P.C.B ASSY.
24 TROUBLE SHOOTING
Concerning Spinning
PROBLEM CHECK POINT CAUSE SOLUTION
YES
Is the lid open? Close the lid.
NO
Does the safety switch NO Safety switch is defec- Change the safety
operate normally? tive. switch.
YES
Is the connector of NO
Improper connection of Connect the connector
P.C.B ASSY connected the connector. properly.
properly?
YES
Is the input
Drain motor is defective. Change the drain motor.
voltage of the drain
motor normal?
NO
P.C.B ASSY is defective. Change the P.C.B ASSY.
YES
Is the V-belt worn out? V-belt is defective. Change the V-belt.
NO
Is the input voltage of YES
Motor is defective. Change the motor.
motor normal?
NO
NO Connect the terminal cor-
Is the connection condi- Improper connection.
tion of capacitor termi- rectly.
nal good?
YES
P.C.B ASSY is defective. Change the P.C.B ASSY.
TROUBLE SHOOTING 25
Concerning Operation
NO
Is the plug connect-ed
Connect the plug.
to electric outlet?
YES
YES
Is Fuse opended? Change Fuse
NO
THE INDICA- NO
Is the condition of Change P.C.B ASSY.
TOR Power button is defective
power button good?
LAMPS(L.E.D)
DO NOT LIGHT YES
UP WHEN THE NO
Is the connector of the Improper connection of Connect the connector
POWER BUT-
P.C.B. ASSY connect- the connector. properly.
TON IS ed properly?
PRESSED.
YES
NO
Is input voltage of the Transformer is defective Change P.C.B Assy
transformer normal?
MOTOR Does the pressure switch NO Pressure switch is defec- Change the pressure
ROTATES operate normally? tive. switch.
WHEN
START/HOLD YES Abnormal
BUTTON IS
Check the output voltage Change P.C.B ASSY.
NOT P.C.B ASSY is defective
of P.C.B ASSY
PRESSED.
26 TROUBLE SHOOTING
8. PRESENTATION OF THE P.C.B ASSY
The drain hose is blocked up by foreign Remove foreign matter from drain hose.
matter.
The water inlet filter clogged. Clean the water inlet filter.
It passes over the 60 minutes, yet it doesnt Check whether or not is comes to the
come to assigned water level. assigned water level.
Wash loads get uneven during spin. Re-set wash loads evenly.
The water level sensing is inferior. Check the water level sensor and the
contact part of the connector.
PCB ASSY 27
APPENDIX
Wiring Diagram
DWF-200W [Non Pump, Single Valve]
28 WIRING DIAGRAM
DWF-200W [Non Pump, Dual Valve]
WIRING DIAGRAM 29
DWF-200W [Pump, Dual Valve]
30 PARTS DIAGRAM
DWF-260W [Non Pump, Single Valve]
31
DWF-260W [Non Pump, Dual Valve]
32
Parts Diagram
PARTS DIAGRAM 33
PUMP MODEL
OPTION
34 PARTS DIAGRAM
PARTS DIAGRAM 35
36 PARTS DIAGRAM
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the
latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr)
Parts List
PARTS DIAGRAM 37
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the
latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr)
38 PARTS DIAGRAM
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the
latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr)
PARTS DIAGRAM 39
Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the
latest parts information, please refer to PPL(Parts Price List) in Service information Center(http://svc.dwe.co.kr)
40 CIRCUIT DIAGRAM
Circuit Diagram
41
DAEWOO ELECTRONICS CO., LTD.
686, AHYEON-DONG MAPO-GU SEOUL, KOREA
C.P.O. BOX 8003 SEOUL, KOREA
TELEX: DWELEC K28177-8
CABLE: DAEWOOELEC
FAX: 82-2-360-7877
TEL: 82-2-360-7114
http://www.dwe.co.kr