USERS MANUAL
Revision 1.0
The information in this Users Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and docu-
mentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interfer-
ence to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
Preface
Manual Organization
Chapter 1 describes the features, specifications and performance of the mother-
board and provides detailed information about the C204 chipset.
Chapter 2 provides hardware installation instructions. Read this chapter when in-
stalling the processor, memory modules and other hardware components into the
system. If you encounter any problems, see Chapter 3, which describes trouble-
shooting procedures for video, memory and system setup stored in the CMOS.
Chapter 4 includes an introduction to the BIOS and provides detailed information
on running the CMOS Setup utility.
Appendix A lists Driver Installation Instructions.
Appendix B provides the UEFI BIOS Recovery Instructions.
iii
X9SCE-F Users Manual
iv
Contacting Supermicro
Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: +1 (408) 503-8000
Fax: +1 (408) 503-8008
Email: marketing@supermicro.com (General Information)
support@supermicro.com (Technical Support)
Web Site: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: +31 (0) 73-6400390
Fax: +31 (0) 73-6416525
Email: sales@supermicro.nl (General Information)
support@supermicro.nl (Technical Support)
rma@supermicro.nl (Customer Support)
Asia-Pacific
Address: Super Micro Computer, Inc.
4F, No. 232-1, Liancheng Rd
Chung-Ho Dist., New Taipei City 235
Taiwan
Tel: +886-(2) 8226-3990
Fax: +886-(2) 8226-3991
Web Site: www.supermicro.com.tw
Technical Support:
Email: support@supermicro.com.tw
Tel: +886-(2)-8226-3990
v
X9SCE-F Users Manual
Table of Contents
Preface
Chapter 1 Introduction
1-1 Overview.......................................................................................................... 1-1
1-2 Chipset Overview ............................................................................................ 1-9
1-3 PC Health Monitoring..................................................................................... 1-10
1-4 Power Supply................................................................................................. 1-10
1-5 Super I/O.........................................................................................................1-11
Chapter 2 Installation
2-1 Standardized Warning Statements.................................................................. 2-1
2-2 Static-Sensitive Devices................................................................................... 2-4
2-3 Motherboard Installation................................................................................... 2-5
Installation Instructions..................................................................................... 2-6
Location of Mounting Holes............................................................................. 2-5
2-4 System Memory............................................................................................... 2-8
How to Install DDR3 DIMMs............................................................................ 2-8
Memory Support............................................................................................... 2-8
Installing and Removing DIMMs...................................................................... 2-9
Memory Population Guidelines...................................................................... 2-10
2-5 Connectors/I/O Ports.......................................................................................2-11
Back Panel Connectors and I/O Ports............................................................2-11
UID Button/LED Indicator.......................................................................... 2-12
Power Button & LED................................................................................. 2-12
KVM Port................................................................................................... 2-12
IPMI_LAN Port.......................................................................................... 2-12
2-6 Connecting Cables......................................................................................... 2-13
IF + POWER............................................................................................. 2-13
SATA DOM Power..................................................................................... 2-13
2-7 Jumper Settings............................................................................................. 2-14
Explanation of Jumpers............................................................................. 2-14
CMOS Clear (JBT1).................................................................................. 2-15
BMC Enable/Disable (JPB1)..................................................................... 2-15
VGA Enable (JPG1) ................................................................................. 2-16
Watch Dog RST/NMI Selection (JWD1)................................................... 2-16
2-8 Onboard Indicators......................................................................................... 2-17
IPMI Dedicated LAN Port.......................................................................... 2-17
IPMI Heartbeat LED.................................................................................. 2-17
vi
Table of Contents
vii
X9SCE-F Users Manual
Notes
viii
Chapter 1: Introduction
Chapter 1
Introduction
1-1 Overview
Congratulations on purchasing your computer motherboard from an acknowledged
leader in the industry. Supermicro boards are designed with the utmost attention
to detail and to provide you with the highest standards in quality and performance.
This motherboard was intended to be used in an SMC system. It is not sold as a
stand-alone product unit. The following items are included in the shipping package.
One (1) Supermicro Motherboard
One (1) Quick Reference Guide (QRG)
Note: For your system to work properly, please follow the links below to
download all necessary drivers/utilities and the user's manual for your
motherboard.
1-1
X9SCE-F Users Manual
X9SCE-F Image
Note: All graphics and images shown in this manual were based upon the latest
PCB Revision available at the time of publishing of the manual. The motherboard
you've received may or may not look exactly the same as the image shown in
this manual.
1-2
Chapter 1: Introduction
Motherboard Layout
UID LED
UID SW
JKVM1
PWR
SW
JPB1
BIOS
J4
JSD1
LED4
HEARTBEAT LED
I-SATA0
MICRO-LP PCI-E 3.0 X8
JPG1
I-SATA1
JPME2
I-SATA2
JBT1
I-SATA3
JWD1
JPME1
X9SCE-F
Rev. 1.0a
CPU1
8
P1-DIMMB2
P1-DIMMB1
P1-DIMMA2
P1-DIMMA1
JPWR2
JP16
JP17 JP18
1-3
X9SCE-F Users Manual
5 4 3 2 1
UID LED
UID SW
JKVM1
23
6 PWR
SW
22
JPB1
BIOS
J4
JSD1 21
LED4
HEARTBEAT LED
I-SATA0
MICRO-LP PCI-E 3.0 X8
7
20
JPG1
I-SATA1
8
19
JPME2
18
I-SATA2
17
9 JBT1
16
I-SATA3
10
JWD1
11 JPME1
12
X9SCE-F
Rev. 1.0a
CPU1
DIMMA1
DIMMA2 Socket H2
DIMMB1 LGA 1155
CPU
DIMMB2
See Note below.
8
P1-DIMMB2
P1-DIMMB1
P1-DIMMA2
P1-DIMMA1
JPWR2
JP16
JP17 JP18
14
13 15
Note: DIMMA1-DIMMB2 memory slots only support very low profile unbuf-
fered (VLP UDIMM) memory modules.
1-4
Chapter 1: Introduction
Jumpers/Ports/Connectors
Jumpers
8 JPME2 ME Manufacturing Mode Pins 1-2 (Normal)
9 JBT1 CMOS Reset Short contact pads to reset CMOS
10 JWD1 Watch Dog Timer RST/NMI Selection Pins 1-2 (Reset)
11 JPME1 ME Recovery Mode Select Pins 1-2 (Normal)
20 JPG1 Onboard VGA Enable/Disable Pins 1-2 (Enabled)
22 JPB1 BMC Enable/Disable Pins 1-2 (Enabled)
1-5
X9SCE-F Users Manual
Motherboard Features
CPU Single Intel Xeon E3-1200 & E3-1200 v. 2 series and 3rd
Gen. Core i3 CPU on an H2 socket (LGA 1155)
Memory Four (4) DIMM slots support up to 32 GB of Dual-Channel
Unbuffered ECC *1600/1333/1066 MHz DDR3 very low
profile (VLP) memory in 4 DIMM modules (*See the note
on Expansion Slots.)
DIMM sizes
DIMM 1 GB, 2 GB, 4 GB and 8GB
Chipset Intel C204 PCH
Expansion Slots One (1) PCI-E Micro-LP (Low Profile) x 8 Slot
*BIOS Rev. 2.0 or above is required for support of new
E3-1200 v. 2 processors, which support PCI-E 3.0 & DDR3
1600 MHz memory.
Graphics One Video (KVM) Port supported by Matrix G200W
Network Connections One (1) Dual Channel RJ-45 Gigabit LAN IPMI Dedicated
LAN Port w/Activity LED
I/O Devices SATA/SAS Connections
SATA 2.0 Ports Two (2) SATA/SAS Ports from
SCU
SATA 3.0 Ports Two (2) (SATA 0/1)
(on IF Backpanel)
USB Devices
one (1) Internal Type A USB connector.
Serial Ports
One (1) COM port on the KVM (Keyboard/Video/Mouse)
connector
BIOS 8 MB SPI AMI BIOS SM Flash BIOS
Play and Plug, ACPI 1.0/2.0/3.0, USB Keyboard, RTC
wakeup and SMBIOS 2.3 support
Power ACPI/ACPM Power Management
Main Switch Override Mechanism
One (1) Disk-On-Module (DOM) Power Connector (SATA)
Power-on mode for AC power recovery
1-6
Chapter 1: Introduction
1-7
X9SCE-F Users Manual
SVID
P29-30
x4 DMI II
VRM 12
5GT/s
MISC VRs
PCIe2.0 x1
5GT/s
RJ45
LPC
FLASH SPI
SPI 64Mb
COM1(KVM)
NCT6776F
LPC I/O
HEALTH
INFO
Note: This is a general block diagram. Please see the Motherboard Features pages
for details on the details of motherboard features.
1-8
Chapter 1: Introduction
The high-speed Direct Media Interface (DMI) featured in the Intel C204 chipset
supports high-speed Direct Media Interface (DMI) for chip-to-chip true isochronous
communication, providing up to 2 Gb/s of software-transparent data transfer rate
on each read/write direction. In addition, the X9SCE-F also features a TCO (Time
Controlled Operations) timer which allows the system to recover from a software/
hardware lock and perform tasks, including ECC Error Reporting, Function Dis-
able and Intruder Detect.
1-9
X9SCE-F Users Manual
1-10
Chapter 1: Introduction
1-11
X9SCE-F Users Manual
Notes
1-12
Chapter 2: Installation
Chapter 2
Installation
Battery Handling
Warning!
Warnung
Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die
Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.
Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.
2-1
X9SCE-F Users Manual
Attention
Danger d'explosion si la pile n'est pas remplace correctement. Ne la remplacer
que par une pile de type semblable ou quivalent, recommande par le fabricant.
Jeter les piles usages conformment aux instructions du fabricant.
Advertencia!
Existe peligro de explosin si la batera se reemplaza de manera incorrecta. Re-
emplazar la batera exclusivamente con el mismo tipo o el equivalente recomen-
dado por el fabricante. Desechar las bateras gastadas segn las instrucciones
del fabricante.
.
.
.
Waarschuwing
Er is ontploffingsgevaar indien de batterij verkeerd vervangen wordt. Vervang de
batterij slechts met hetzelfde of een equivalent type die door de fabrikant aan-
bevolen wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften
afgevoerd te worden.
2-2
Chapter 2: Installation
Product Disposal
Warning!
Ultimate disposal of this product should be handled according to all national laws
and regulations.
Warnung
Die Entsorgung dieses Produkts sollte gem allen Bestimmungen und Gesetzen
des Landes erfolgen.
Advertencia!
Al deshacerse por completo de este producto debe seguir todas las leyes y regla-
mentos nacionales.
Attention
La mise au rebut ou le recyclage de ce produit sont gnralement soumis des
lois et/ou directives de respect de l'environnement. Renseignez-vous auprs de
l'organisme comptent.
2-3
X9SCE-F Users Manual
Waarschuwing
De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming
met alle nationale wetten en reglementen.
Precautions
Use a grounded wrist strap designed to prevent static discharge.
Touch a grounded metal object before removing the board from the antistatic
bag.
Handle the board by its edges only; do not touch its components, peripheral
chips, memory modules or gold contacts.
Put the motherboard and peripherals back into their antistatic bags when not in
use.
For grounding purposes, make sure that your computer chassis provides excel-
lent conductivity between the power supply, the case, the mounting fasteners
and the motherboard.
Use only the correct type of onboard CMOS battery. Do not install the onboard
upside down battery to avoid damaging the components.
Unpacking
The motherboard is shipped in antistatic packaging to avoid static damage. When
unpacking the board, make sure the person handling it is static protected.
2-4
Chapter 2: Installation
Tools Needed
Note: The above items are not provided with this motherboard.
UID SW
UID LED
JSD1
I-SATA3
JPWR2
JPB1
JPG1
Rev. 1.0a
BIOS
CPU1
JKVM1
JPME2
J4
JBT1
P1-DIMMA1
LED4 P1-DIMMA2
HEARTBEAT LED JWD1 P1-DIMMB1
JP16
P1-DIMMB2
JPME1
JP17 JP18
Image rotated 90
2-5
X9SCE-F Users Manual
Caution: To avoid damaging the motherboard and its components, please do not use
a force greater than 8 lb/inch on each mounting screw during motherboard installation.
Installation Instructions
1
Locate the mounting holes on the motherboard. Refer to the layout on the
previous page for mounting hole locations.
2
Locate the matching mounting holes on the motherboard mounting tray.
Install standoffs needed. Align the mounting holes on the motherboard
against the mounting holes on the motherboard tray.
Stand Off
3
Install the motherboard carefully to avoid damaging motherboard compo-
nents.
4
Insert a Pan head #6 screw into a mounting hole on the motherboard and
its matching mounting hole on the chassis, using the Philips screwdriver.
2-6
Chapter 2: Installation
The image above shows the the X9SCE-F motherboard mounted on a tray and the
way it is installed as one of the nodes in a server chassis.
2-7
X9SCE-F Users Manual
CAUTION
Exercise extreme care when installing or removing DIMM
modules to prevent any possible damage.
Note: Check the Supermicro website for a list of memory modules that
have been validated with the X9SCE-F motherboard.
2. Insert each DIMM module vertically and snap it into place. Repeat step 1 to
install more memory, if needed. See instructions on the next page.
Memory Support
This motherboard supports up to 32GB of Unbuffered ECC DDR3 1066/1333/1600*
MHz VLP (Very Low Profile) memory in 4 DIMM slots. (*BIOS rev. 2.0 is needed
for support of new E3-1200 v2 CPUs, which support PCI-E 3.0 and DDR3 1600
MHz memory.)
I-SATA3
JPWR2
JPB1
JPG1
Rev. 1.0a
BIOS
CPU1
JKVM1
JPME2
J4
JBT1
P1-DIMMA1
LED4 P1-DIMMA2
HEARTBEAT LED JWD1 P1-DIMMB1 DIMMA1
JP16
P1-DIMMB2
DIMMA2
JPME1
JP17 JP18
2-8
Chapter 2: Installation
Notches
Release
2
Push a Lock/Release tab
to the Release position.
Make sure that the side
notches of the DIMM
module aligns with the Lock/ Release
Release tab of the slot as it is
Lock/Release Tabs
pressed in.
3
Insert the DIMM mod-
ule vertically and press
down until the module
snaps into place.
Press Down
4
When the module is
properlly inserted, the
Lock/Release tabs will
automatically secure
the DIMM module, locking it
into place.
Lock
Release
Lock
5
To Remove:
Use your thumbs to Release
gently push the Lock/
Release tabs near both
ends of the module. This should
release it from the slot. Pull the
DIMM module upwards.
2-9
X9SCE-F Users Manual
1. When installing memory modules, the DIMM slots should be populated in the
following order: DIMMA2, DIMMB2, DIMMA1 and DIMMB1.
2. Always use DDR3 DIMM modules of the same size, type and speed.
3. The motherboard will support one DIMM module or three DIMM modules
installed. For best memory performance, install DIMM modules in pairs.
2-10
Chapter 2: Installation
UID SW
UID LED
JSD1
I-SATA3
JPWR2
I-SATA0 I-SATA1 I-SATA2
X9SCE-F
PWR
SW
JPB1
JPG1
Rev. 1.0a
BIOS
CPU1
JKVM1
8
JPME2
J4
JBT1
P1-DIMMA1
LED4 P1-DIMMA2
HEARTBEAT LED JWD1 P1-DIMMB1
JP16
P1-DIMMB2
JPME1
JP17 JP18
MICRO-LP PCI-E 3.0 X8
Image rotated 90
1 2 3 4
2-11
X9SCE-F Users Manual
KVM Port
The KVM port (JKVM) supports key-
board, VGA, mouse via UART interface.
Please attach a compatible KVM connec-
tor/switch to this port.
IPMI_LAN Port
A dedicated IPMI_LAN port is located
next to the KVM port to provide dedi-
cated network connection for IPMI 2.0.
This port accepts RJ45 type cables.
2-12
Chapter 2: Installation
IF + POWER
This edge connector, located on the opposite end of the motherboard from the I/O
back panel, is used to connect the motherboard to the back plane of the server
chassis. Through this connector, the motherboard receives its power and commu-
nicates with other components installed in the system.
UID SW
B
UID LED A IF + Power
JSD1
I-SATA3
JPWR2
JPB1
JPG1 B SATA DOM Power
Rev. 1.0a
BIOS
CPU1
JKVM1
JPME2
J4
JBT1
P1-DIMMA1
LED4 P1-DIMMA2
HEARTBEAT LED JWD1 P1-DIMMB1
JP16
P1-DIMMB2
JPME1
JP17 JP18
2-13
X9SCE-F Users Manual
Explanation of Jumpers
To modify the operation of the motherboard, jumpers can be used to choose between
optional settings. Jumpers create shorts between two pins to change the function
of the connector. Pin 1 is identified with a square solder pad on the printed circuit
board.
Note: On two pin jumpers, "Closed" means the jumper is on and "Open" means
the jumper is off the pins.
2-14
Chapter 2: Installation
UID SW
UID LED
B A CMOS Clear
JSD1
I-SATA3
JPWR2
JPB1
B BMC Enable/Disable
JPG1
Rev. 1.0a
BIOS
CPU1
JKVM1
JPME2
A
J4
JBT1
P1-DIMMA1
LED4 P1-DIMMA2
HEARTBEAT LED JWD1 P1-DIMMB1
JP16
P1-DIMMB2
JPME1
JP17 JP18
Image rotated 90
2-15
X9SCE-F Users Manual
UID SW
UID LED A VGA Enable
JSD1
I-SATA3
JPWR2
BIOS
CPU1
JKVM1
JPME2
J4
JBT1
P1-DIMMA1
LED4
HEARTBEAT LED A JWD1
P1-DIMMA2
P1-DIMMB1
JP16
P1-DIMMB2
JPME1
JP17 JP18
Image rotated 90
2-16
Chapter 2: Installation
the speed of the connection. See the Activity Amber: Blinking Active
tables at right for more information. Speed Green: Solid 100 Mbps
On
UID SW
UID LED
A IPMI LAN Port
JSD1
I-SATA3
JPWR2
BIOS
CPU1
JKVM1
JPME2
A
J4
JBT1
P1-DIMMA1
B LED4
HEARTBEAT LED JWD1
P1-DIMMA2
P1-DIMMB1
JP16
P1-DIMMB2
JPME1
JP17 JP18
Image rotated 90
2-17
X9SCE-F Users Manual
Unit ID LED
The Unit LED is controlled by the Unit ID Unit ID LED
LED Status
Button. It indicates a unit that may be in
On (Steady) Unit ID switch is on
need of service. Turn on the UID button in
the front of the chassis or on the mother-
board's I/O panel to identify the failed unit.
A
UID SW
UID LED A Unit ID LED
JSD1
I-SATA3
JPWR2
JPB1
JPG1
Rev. 1.0a
BIOS
CPU1
JKVM1
JPME2
J4
JBT1
P1-DIMMA1
LED4 P1-DIMMA2
HEARTBEAT LED JWD1 P1-DIMMB1
JP16
P1-DIMMB2
JPME1
JP17 JP18
Image rotated 90
2-18
Chapter 2: Installation
UID SW A B C D
UID LED
A I-SATA 0
JSD1
I-SATA3
JPWR2
JPB1
JPG1
B I-SATA 1
Rev. 1.0a
BIOS
CPU1
JKVM1
C I-SATA 2
8
JPME2 D I-SATA 3
J4
JBT1
P1-DIMMA1
LED4 P1-DIMMA2
HEARTBEAT LED JWD1 P1-DIMMB1
JP16
P1-DIMMB2
JPME1
JP17 JP18
Image rotated 90
2-19
X9SCE-F Users Manual
Notes
2-20
Chapter 3: Troubleshooting
Chapter 3
Troubleshooting
Before Power On
1. Be sure to unplug the power cable before installing or removing the compo-
nents.)
2. Make sure that there are no short circuits between the motherboard and chas-
sis.
3. Disconnect all ribbon/wire cables from the motherboard, including those for the
keyboard and mouse. Also, be sure to remove all add-on cards.
No Power
1. Make sure that there are no short circuits between the motherboard and chas-
sis.
2. Make sure that all jumpers are set to their default positions.
5. The battery on your motherboard may be old. Check to make sure that it still
supplies ~3VDC. If it does not, replace it with a new one.
No Video
1. If the power is on, but you have no video-in this case, you will need to remove
all the add-on cards and cables first.
3-1
X9SCE-F Users Manual
Memory Errors
1. Make sure that all DIMM modules are properly installed and fully seated in
the slots.
2. Please check Section 2-4 and make sure that you are using the correct memory.
Also, it is recommended that you use the memory modules of the same type
and speed for all DIMMs in the system.
3. Check for bad DIMM modules or slots by swapping modules between slots to
see if you can locate the faulty modules.
2. The battery on your motherboard may be old. Check to verify that it still supplies
~3VDC. If it does not, replace it with a new one.
3. If the above steps do not fix the Setup Configuration problem, contact your
vendor for repairs.
Note: Not all BIOS can be flashed. Some cannot be flashed; it depends
on the modifications to the boot block code.
3. If you've followed the instructions above to troubleshoot your system, and still
cannot resolve the problem, then contact Supermicro's technical support and
provide them with the following information:
3-2
Chapter 3: Troubleshooting
4. Distributors: For immediate assistance, please have your account number ready
when placing a call to our technical support department. We can be reached
by e-mail at support@supermicro.com, by phone at: (408) 503-8000, option
2, or by fax at (408)503-8019.
Answer:
Question: Why does Microsoft Windows show less memory than what is
physically installed?
Answer: It is recommended that you do not upgrade your BIOS if you are not
experiencing any problems with your system. Updated BIOS files are located
on our web site at http://www.supermicro.com/support/bios/. Please check our
BIOS warning message and the information on how to update your BIOS on our
website. Select your motherboard model and download the BIOS (.rom) file to
your computer. Also, check the current BIOS revision and make sure that it is
newer than your BIOS before downloading. You may choose the zip file or the
.exe file. If you choose the zipped BIOS file, please unzip the BIOS file onto a
bootable device or a USB pen/thumb drive. To flash the BIOS, run the batch
3-3
X9SCE-F Users Manual
file named "ami.bat" with the new BIOS ROM file from your bootable device or
USB pen/thumb drive. Use the following format:
Notes: Always use the file named ami.bat to update the BIOS and insert
a space between "ami.bat" and the filename. The BIOS-ROM-filename
will bear the motherboard name (i.e., X9SCD) and build version as the
extension. For example, "X9SCD0.526".
When completed, your system will automatically reboot. If you choose the .exe
file, please run the .exe file under Windows to create the BIOS flash floppy disk.
Insert the floppy disk into the system you wish to flash the BIOS. Then, boot
the system to the floppy disk. The BIOS utility will automatically flash the BIOS
without any prompts. Please note that this process may take a few minutes
to complete. Do not be concerned if the screen is paused for a few minutes.
Warning: Do not shut down or reset the system while updating the BIOS to prevent
possible system boot failure!
When the BIOS flashing screen is completed, the system will reboot and will
show Press F1 or F2. At this point, you will need to load the BIOS defaults.
Press <F1> to go to the BIOS setup screen, and press <F9> to load the default
settings. Next, press <F10> to save and exit. The system will then reboot.
Note: The SPI BIOS chip installed on this motherboard is not removable.
To repair or replace a damaged BIOS chip, please send your motherboard
to RMA at Supermicro for service.
If your BIOS crashes and your motherboard will no longer boot, please read Ap-
pendix C - UEFI BIOS Recovery Instructions for instructions.
Question: What's on the CD that came with my motherboard?
Answer: The supplied compact disc has quite a few drivers and programs
that will greatly enhance your system. We recommend that you review the CD
and install the applications you need. Applications on the CD include chipset
drivers for Windows, security and audio drivers.
3-4
Chapter 3: Troubleshooting
Battery Removal
To remove the onboard battery, follow the steps below:
1. Power off your system and unplug your power cable.
3. Using a tool such as a pen or a small screwdriver, push the battery lock out-
wards to unlock it. Once unlocked, the battery will pop out from the holder.
Battery Battery
Lock
Battery Holder
Proper Battery Disposal
Warning! Please handle used batteries carefully. Do not damage the battery in any
way; a damaged battery may release hazardous materials into the environment. Do
not discard a used battery in the garbage or a public landfill. Please comply with the
regulations set up by your local hazardous waste management agency to dispose of
your used battery properly.
Battery Installation
1. To install an onboard battery, follow the steps 1& 2 above and continue
below:
2. Identify the battery's polarity. The positive (+) side should be facing up.
3. Insert the battery into the battery holder and push it down until you hear a
click to ensure that the battery is securely locked.
Warning: When replacing a battery, be sure to only replace it with the same type.
3-5
X9SCE-F Users Manual
This warranty only covers normal consumer use and does not cover damages
incurred in shipping or from failure due to the alteration, misuse, abuse or improper
maintenance of products.
During the warranty period, contact your distributor first for any product prob-
lems.
3-6
Chapter 4: AMI BIOS
Chapter 4
BIOS
4-1 Introduction
This chapter describes the AMI BIOS Setup Utility for the X9SCE-F motherboard.
The AMI ROM BIOS is stored in a Flash EEPROM and can be easily updated. This
chapter describes the basic navigation of the AMI BIOS Setup Utility setup screens.
Note: For instructions on BIOS recovery, please refer to the instruction
guide posted at http://www.supermicro.com/support/manuals/.
Each main BIOS menu option is described in this manual. The Main BIOS setup
menu screen has two main frames. The left frame displays all the options that can
be configured. Grayed-out options cannot be configured. Options in blue can be
configured by the user. The right frame displays the key legend. Above the key
legend is an area reserved for a text message. When an option is selected in the
left frame, it is highlighted in white. Often a text message will accompany it. (Note:
the AMI BIOS has default text messages built in. Supermicro retains the option to
include, omit, or change any of these text messages.)
The AMI BIOS Setup Utility uses a key-based navigation system called "hot keys".
Most of the AMI BIOS setup utility "hot keys" can be used at any time during the
setup navigation process. These keys include <F1>, <F10>, <Enter>, <ESC>, ar-
row keys, etc.
Note: Options printed in Bold are default settings.
4-1
X9SCE-F Users Manual
Warning! Do not upgrade the BIOS unless your system has a BIOS-related issue.
Flashing the wrong BIOS can cause irreparable damage to the system. In no event
shall Supermicro be liable for direct, indirect, special, incidental, or consequential dam-
ages arising from a BIOS update. If you have to update the BIOS, do not shut down
or reset the system while the BIOS is updating. This is to avoid possible boot failure.
4-2
Chapter 4: AMI BIOS
Processor
The AMI BIOS will automatically display the status of processor as shown below:
Processor
Speed
Physical Count
Logical Count
System Memory
This displays the size of memory available in the system:
Size
4-3
X9SCE-F Users Manual
Boot Feature
Quiet Boot
This feature allows the user to select the bootup screen display between POST
messages and the OEM logo. Select Disabled to display the POST messages.
Select Enabled to display the OEM logo instead of the normal POST messages.
The options are Enabled and Disabled.
Bootup Num-Lock
This feature selects the Power-on state for Numlock key. The options are Off
and On.
4-4
Chapter 4: AMI BIOS
CPU Configuration
Note: Take Caution when changing the Advanced settings. An incorrect
value may cause system to become unstable. When this occurs, revert
to the default setting.
4-5
X9SCE-F Users Manual
Intel AES-NI
Set to Enabled to use the processor's Advanced Encryption Standard (AES) feature.
The options are Enabled and Disabled.
Power Technology
This feature determines what power-saving scheme the motherboard uses. The
options are Disabled, Energy Efficient and Custom. If Custom is selected, the
following options become available:
4-6
Chapter 4: AMI BIOS
power consumption and heat dissipation. Please refer to Intels web site
for detailed information. The options are Disabled and Enabled.
CPU C3 Report (Available when Power Technology is set to Custom)
Select Enabled to allow the BIOS to report the CPU C3 State (ACPI C2) to
the operating system. During the CPU C3 State, the CPU clock generator
is turned off. The options are Enabled and Disabled.
Select Enabled to allow the BIOS to report the CPU C6 State (ACPI C3) to
the operating system. During the CPU C6 State, the power to all cache is
turned off. The options are Enabled and Disabled.
Select Enabled to allow the BIOS to report the CPU C7 State (ACPI C3) to
the operating system. CPU C7 State is a processor-specific low C-State.
The options are Enabled and Disabled.
4-7
X9SCE-F Users Manual
Chipset Configuration
WARNING: Setting the wrong values in the following sections may cause the system
to malfunction.
This item displays the current CPU Revision, Current CPU1 Memory Fre-
quency, Memory Type and Memory Reference Code Revision.
Memory Frequency
This feature allows the user to select the memory speed. Under normal
conditions, please set this to Auto. The options are Auto, Force DDR-
1066, Force DDR-1333, and Force DDR-1600.
Intel VT-d
Select Enabled to enable Intel's Virtualization Technology support for
Direct I/O VT-d by reporting the I/O device assignments to VMM through
the DMAR ACPI Tables. This feature offers fully-protected I/O resource-
sharing across the Intel platforms, providing the user with greater reliabil-
ity, security and availability in networking and data-sharing. The settings
are Enabled and Disabled.
4-8
Chapter 4: AMI BIOS
De-emphasis Control
Use this feature to configure the de-emphasis control on PEG. The options
are -6 dB and -3.5 dB.
USB Functions
This feature allows the user to decide the number of onboard USB ports to
be enabled. The Options are Disabled and Enabled.
4-9
X9SCE-F Users Manual
IDE/SATA Configuration
When this submenu is selected, the AMI BIOS automatically detects the presence
of the IDE devices and displays the following items:
SATA Mode
This item selects the mode for the installed drives. The options are Disabled, IDE
Mode, AHCI Mode and RAID Mode.
IDE Mode
The following items are displayed when IDE Mode is selected:
SATA Port0~Port5
This item displays the information detected on the installed SATA drives
on the particular SATA port.
AHCI Mode
The following items are displayed when AHCI Mode is selected:
SATA Port0~Port5
This item displays the information detected on the installed SATA drives
on the particular SATA port.
Hot Plug
Set this item to Enabled for hot-plugging support. The options are
Enabled and Disabled.
Staggered Spin Up
Set this item to Enabled for Staggered Spin-up support. The options
are Enabled and Disabled.
4-10
Chapter 4: AMI BIOS
RAID Mode
The following items are displayed when RAID Mode is selected:
SATA Port0~Port5
This item displays the information detected on the installed SATA drives
on the particular SATA port.
Hot Plug
Set this item to Enabled to enable hot-plugging. The options are
Enabled and Disabled.
PCIe/PCI/PnP Configuration
This feature allows the user to set the PCI/PnP configurations for the following
items:
PERR# Generation
Select Enabled to allow a PCI device to generate a PERR number for a PCI Bus
Signal Error Event. The options are Enabled and Disabled.
SERR# Generation
Select Enabled to allow a PCI device to generate an SERR number for a PCI Bus
Signal Error Event. The options are Enabled and Disabled.
4-11
X9SCE-F Users Manual
Serial Port 1
Select Enabled to enable the onboard serial port. The options are Enabled and
Disabled.
COM 1, SOL
These two submenus allow the user to configure the following Console Redirection
settings for a COM Port specified by the user.
4-12
Chapter 4: AMI BIOS
Data Bits
Use this feature to set the data transmission size for Console Redirection. The
options are 7 Bits and 8 Bits.
Parity
A parity bit can be sent along with regular data bits to detect data transmission
errors. Select Even if the parity bit is set to 0, and the number of 1's in data bits
is even. Select Odd if the parity bit is set to 0, and the number of 1's in data bits
is odd. Select None if you do not want to send a parity bit with your data bits
in transmission. Select Mark to add a mark as a parity bit to be sent along with
the data bits. Select Space to add a Space as a parity bit to be sent with your
data bits. The options are None, Even, Odd, Mark and Space.
Stop Bits
A stop bit indicates the end of a serial data packet. Select 1 Stop Bit for standard
serial data communication. Select 2 Stop Bits if slower devices are used. The
options are 1 and 2.
Flow Control
This feature allows the user to set the flow control for Console Redirection to
prevent data loss caused by buffer overflow. Send a "Stop" signal to stop send-
ing data when the receiving buffer is full. Send a "Start" signal to start sending
data when the receiving buffer is empty. The options are None and Hardware
RTS/CTS.
Recorder Mode
Select Enabled to capture the data displayed on a terminal and send it as text
messages to a remote server. The options are Disabled and Enabled.
Resolution 100x31
Select Enabled for extended-terminal resolution support. The options are Dis-
abled and Enabled.
4-13
X9SCE-F Users Manual
Putty KeyPad
This feature selects Function Keys and KeyPad settings for Putty, which is a
terminal emulator designed for the Windows OS. The options are VT100, LINUX,
XTERMR6, SCO, ESCN, and VT400.
Terminal Type
This feature allows the user to select the target terminal emulation type for Con-
sole Redirection. Select VT100 to use the ASCII character set. Select VT100+
to add color and function key support. Select ANSI to use the extended ASCII
character set. Select VT-UTF8 to use UTF8 encoding to map Unicode characters
into one or more bytes. The options are ANSI, VT100, VT100+, and VT-UTF8.
4-14
Chapter 4: AMI BIOS
Flow Control
This feature allows the user to set the flow control for Console Redirection to
prevent data loss caused by buffer overflow. Send a "Stop" signal to stop send-
ing data when the receiving buffer is full. Send a "Start" signal to start sending
data when the receiving buffer is empty. The options are None, Hardware RTS/
CTS, and Software Xon/Xoff.
Fan1 Speed
This feature displays the fan speed reading from the Fan 1 interface.
VCORE, 12V, VDIMM, 5VCC, VCC PCH, AVCC, 3.3VCC, VSB, VBAT
This feature displays the current voltages of the above voltage monitors.
4-15
X9SCE-F Users Manual
ACPI Settings
Use this feature to configure Advanced Configuration and Power Interface (ACPI)
power management settings for your system.
Suspend Mode
This setting allows you to configure the ACPI (Advanced Configuration and Power
Interface) sleep state for your system when it is in the Suspend mode. The options
are Suspend Disabled, S1 (POS), and S3 (STR). S3 (STR) is the deepest sleep
state in these options.
WHEA Support
This feature Enables the Windows Hardware Error Architecture (WHEA) support
for the Windows 2008 operating system (and later versions). The options are
Enabled and Disabled.
ME Subsystem
This feature displays the following ME Subsystem Configuration settings.
4-16
Chapter 4: AMI BIOS
MECI
The Multiple Event Count Increment (MECI) counter counts the number of occur-
rences a duplicate event must happen before the MECI counter is incremented.
This is a numeric value.
4-17
X9SCE-F Users Manual
METW
The Multiple Event Time Window (METW) defines number of minutes must pass
between duplicate log events before MECI is incremented. This is in minutes,
from 0 to 99.
4-18
Chapter 4: AMI BIOS
4-19
X9SCE-F Users Manual
4-6 Boot
Boot Option #1, Boot option #2, Boot Option #3, etc
The settings are Built-in EFI Shell, [any detected boot device] and Disabled.
4-20
Chapter 4: AMI BIOS
4-7 Security
Password Check
Use this feature to determine when a password entry is required. Select Setup to
require the password only when entering setup. Select Always to require the pass-
word when entering setup and on each boot. The options are Setup and Always.
Administrator Password
Use this feature to set the Administrator Password which is required to enter the
BIOS setup utility. The length of the password should be from 3 characters to 20
characters long.
4-21
X9SCE-F Users Manual
4-8 Exit
Select the Exit tab from the BIOS Setup Utility screen to enter the Exit BIOS Setup
screen.
Discard Changes
Select this option and press <Enter> to discard all the changes and return to the
AMI BIOS Utility Program.
Restore Defaults
To set this feature, select Restore Defaults from the Exit menu and press <Enter>.
These are factory settings designed for maximum system stability, but not for
maximum performance.
4-22
Chapter 4: AMI BIOS
Boot Override
This feature allows the user to override the Boot Option Priorities setting in the Boot
menu, and instead immediately boot the system with one of the listed devices. This
is a one-time override.
4-23
X9SCE-F Users Manual
Notes
4-24
Appendix A: Software Installation Instructions
Appendix A
A-1
X9SCE-F Motherboard Users Manual
A-2
Appendix A: Software Installation Instructions
Note: The SD III utility and user guide can be downloaded from our
website at: http://www.supermicro.com/products/accessories/software/
SuperDoctorIII.cfm. For Linux, we will still recommend that you use
Supero Doctor II.
A-3
X9SCE-F Motherboard Users Manual
Notes
A-4
Appendix B: UEFI BIOS Recovery
Appendix B
Warning! Do not upgrade the BIOS unless your system has a BIOS-related issue.
Flashing the wrong BIOS can cause irreparable damage to the system. In no event shall
Supermicro be liable for direct, indirect, special, incidental, or consequential damages
arising from a BIOS update. If you need to update the BIOS, do not shut down or reset
the system while the BIOS is updating to avoid possible boot failure.
Note: Follow the BIOS Recovery instructions below for BIOS recovery
when the main BIOS block crashes. However, when the BIOS Boot sec-
tor crashes, you will need to send the motherboard back to Supermicro
for RMA repair.
B-1
X9SCE-F Users Manual
To perform UEFI BIOS recovery using a USB-attached device, follow the instruc-
tions below.
1. Using a different machine, copy the "Super.ROM" binary image file into the
disc Root "\" Directory of a USB device or a writeable CD/DVD.
Note: If you cannot locate the "Super.ROM" file in your driver disk, visit
our website at www.supermicro.com to download the BIOS image into a
USB flash device and rename it to "Super ROM" for BIOS recovery use.
2. Insert the USB device that contains the new BIOS image ("Super.Rom") into
your USB drive and power on the system
3. While powering on the system, keep pressing <Ctrl> and <Home> simultane-
ously on your PS2 or USB keyboard until your hear two short beeps. This
may take from a few seconds to one minute.
4. After locating the new BIOS binary image, the system will enter the BIOS
Recovery page as shown below.
Note: At this point, you may decide if you want to start with BIOS Recovery.
If you decide to proceed with BIOS Recovery, follow the procedures below.
WARNING! BIOS Recovery Mode has been detected Set this to start flash
update
Flash Update Parameters
Reset NVRAM [Enabled]
: Select Screen
: Select Item
Enter: Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
5. When the screen as shown above displays, using the arrow key, select the
item- "Proceed with flash update" and press the <Enter> key. You will see the
progress of BIOS Recovery as shown in the screen below.
B-2
Appendix B: UEFI BIOS Recovery
: Select Screen
: Select Item
Enter: Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
6. After the process of BIOS Recovery is complete, press any key to reboot the
system
: Select Screen
: Select Item
Enter: Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
7. Using a different system, extract the BIOS package into a bootable USB flash
drive.
B-3
X9SCE-F Users Manual
9. After seeing the message that BIOS update is completed, unplug the AC
power cable to clear CMOS, and then plug in the AC power cable to power
on the system.
12. After loading default settings, press <F4> to save the settings and exit the
BIOS Setup utility.
B-4
Disclaimer
The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices,
aircraft/emergency communication devices or other critical systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic
property damage. Accordingly, Supermicro disclaims any and all liability, and should buyer use or sell such products for use in such ultra-hazardous applications, it does so
entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and
proceedings of any kind arising out of or related to such ultra-hazardous use or sale.