This tutorial will teach you in very easy steps how to design class-A amplifiers. Starting with the
results of bias point design we get the following circuit
The most important rule developing such an amplifier is to distinguish between the DC-analysis as
done during bias point calculation and AC-analysis starting at this point.
The source impedance of an ideal voltage source is 0 which means, that the positive power line
V+ and the ground line GND are short circuited for AC-signals. The result is the next circuit
schematic.
It is the equivalent circuit for AC-analysis. Bypass capacitors may be placed in parallel to each
resistor in that sense, that the regarding transistor port is connected to ground (grounded) for AC-
signals. The AC-voltage drop along the capacitor is very small and can be neglected. The coupling
capacitors CC1 and CC2 prevent DC current flow through the source and respectively load. The bias
point is independent from source and load impedance.
If the emitter is grounded by a capacitor CE, we get the common emitter circuit. The emitter
is both used for input and output, the base pin is the input node, the collector pin is the
output node.
If the base is grounded by a capacitor CB, we get the common base circuit. The base is both
used for input and output, the emitter pin is the input node, the collector pin is the output
node.
Note: There are three more circuit options by exchange of the input and output pins but these
circuits are not relevant in this tutorial.
U BE
UT
I B =I s e 1
and for small signals
U BE U BE
dI B 1 I I I I
=I S e U 11
T
= S e U 1 S = B S . T
dU BE UT UT UT UT UT
Since the base-emitter junction is forward biased, we get I B I S and
U BE
dI B IS U IB
e 1 = =g BE
T
dU BE U T UT
the value of the input conduction of the bipolar junction transistor if small signals are applied at
low frequencies . Finally one gets the AC input resistance as
1 UT
r BE = = .
g BE I B
The collector current IC is I C =B I B and therefore
U BE
I C =B I B =B I s e UT
1 ,
and for small signals
U BE
dI C I I I I
=B S e U 1 B S = C B S
T
dU BE UT UT UT UT
and one gets for forward biased base emitter junction
U BE
dI C I I
B S e U 1 = C =g M , T
dU BE UT UT
the mutual conduction, a relation between input voltage change to output current change. Since
there is a very little difference between the DC current gain B and the AC current gain , B is
replaced with in the following equations.
Now we have reached the point, where a very simple equivalent circuit for AC analysis at the bias
point can be built:
If this simple equivalent circuit is used, the physical circuit shown in Figure 6 can be transformed to
the circuit in Figure 9:
It is easy to derive the equation for the input resistance and the result is
R12
Rin = .
g M R12
Starting at U 2=I C RC =g M U BE RC and U BE =U 1 one gets
U2
VU= =g M RC
U1
for the voltage gain VU.
Because the bipolar junction transistors width of the base is slightly dependent of the voltage
applied between collector and emitter, the output conductance go must be taken into account. The
output conductance for small AC signals is the rise of the collector current IC as a function of the
applied voltage between collector and emitter UCE.
dI c IC I UT
go= = = C = g M C .
d U CE U CE U early U T U CE U early
The influence of a change of UCE on the change of IC is called the output conductance.
UT
C = .
U CE U early
If the base width changes with respect to the output voltage, the voltage drop on the base emitter
junction changes too. There is a reverse influence of the output voltage UCE to the input voltage UBE
d U BE
B= C .
d U CE
Finally, we get an equivalent transistor circuit for small signals at low frequencies.
1
The current g M U BE flows through the parallel connected resistors and RC .
g M C
g M RC
Therefore, the resulting output voltage is U 2=U 1 and the voltage gain equals
1g M C RC
U2 g M RC
VU= = .
U1 1g M C RC
The input resistance of the biased transistor is defined as the voltage applied at the base pin divided
by the current which flows into the base pin
U BE 1 g M C R C
RTin= = .
IB g m 1 B C g M RC
The input resistance is defined as the voltage applied at the input port divided by the current which
flows into the input port and results in the parallel connection of RTin and R12.
RTin R12
Rin =
RTin R12
The output resistance is defined as the voltage applied at the output port divided by the current
which flows into the output port
U2 g M R12
Rout = =RC .
I2 1 g M C R C g M R12 B g 2M R12 RC
Due to a slight change in the base width, there is a resulting influence of the collector resistor RC on
the input resistance Rin. The output resistance depends on the parallel connection of the resistors R1
and R2. The voltage gain VU becomes reduced due to the base width modulation. The temperature
stability of the voltage gain depends on bias point and temperature, because the mutual
IC
conductance g M = changes with temperature. A possible goal of correct biasing is the
UT
temperature stability of gM. In order to increase the overall temperature stability, a negative
feedback might be applied to the circuit.
Figure 12: Physical circuit and equivalent circuit with negative AC-
feedback
The next step in determining the circuit properties is if the physical transistor is replaced by the
equivalent small signal transistor model for low frequencies.
Applying of Norton's Theorem two meshes to solve for the unknown currents can be found. In the
following equations the resistor RE' is renamed by RE. Otherwise the equations need more than one
line for printing which results in unreadable forms. Applying Ohm's law and after some irksome
substitutions the transistor input resistance can be found as
U1 R E g M BC
RTin= =
C
I B g M BC
R E RE
B
g M BC R E RC g M B C 1
.
RTin=
U1
IB
=RE 1
R E g M C
R E RC g M C 1 g M
Dipl. Ing. Dr. Peter Frhling -6- October 2012
and for vanishing base width modulation B and C
RTin= 1 RE
gM
The input resistance is defined as the voltage applied at the input port divided by the current which
flows into the input port and results in the parallel connection of RTin and R12.
RTin R12
Rin =
RTin R12
RE
C
g M BC R E RC g M BC 1 RE
1 B
g M B C
RE g M BC
Neglect of reverse voltage gain B results in
RC
VU=
RE
gM RE RC g M C 1 R E RE g M C