LOAD INCREMENT
[=AVE.READING(t)-
AVERAGE GROSS
AVERAGE GROSS
AVE.READING(t0)]
AVE.READING(0)]
MOVEMENT
MOVEMENT
GAUGE READING GAUGE READING
LOAD (inches) LOAD (inches)
(tons) (tons)
0 100% 0
11 0
5 0
75% 0
5
0 0
12 0 50% 0
5 5
0
25% 0
0 5
13 0
5 0
0 0
30
0
14 0
5 GROSS MOVEMENT =
PERMANENT SETTLEMENT =
0 ACCEPTABLE or PLUNGING?
15 0
15 0
5 ELASTIC REBOUND - =
STATE OF LOUISIANA AMA 3-12-09
LOAD INCREMENT
[=AVE.READING(t)-
AVE.READING(t0)]
AVERAGE GROSS
AVERAGE GROSS
AVE.READING(0)]
MOVEMENT
MOVEMENT
GAUGE READING GAUGE READING
LOAD (inches) LOAD (inches)
(tons) (tons)
0.000
DEFLECTION (INCHES)
-0.020
-0.040
-0.060
-0.080
-0.100
-0.120
-0.140
-0.160
-0.180
0 0 0 0 0 1 1 1 1 1 1
LOAD (TONS)
Loading Curve Data Rebound Curve Data 0.05 Tons / Inch Slope Elastic Curve Curve Davisson Curve
LOAD TEST PILE DEFLECTION CURVE
0.000
0 50 100 150 200 250 300 350 400
DEFLECTION (INCHES)
-0.200
-0.400
-0.600
-0.800
-1.000
-1.200
-1.400
Loading Curve Data Rebound Curve Data 0.05 Tons / Inch slope Elastic Curve P5 Davisson Curve P5
LADOTD Std
Step P Test Pile Loading Details (Quick Method) Spec
pile driven according to approved pile installation plan 804.11
correct hammer size 804.05( c )(2)
correct hammer cushion material and thickness ( 75% original), [see submittal, PE
804.06((b)(1)
checks hammer on ground]
driving
for greater accuracy a load cell calibrated to accuracy of 2% of the applied load and
equiped with spherical bearings
load cell calibrated within six months of loading date and approved by Materials Lab 804.11(g)(5)
when required (long unbraced lengths), contractor to provide bracing or strengthening of
804.11(f)
test pile during driving or loading
two parallel reference beams, one on each side of the test pile, independently supported
and oriented to place their supports as far as practical from anchor piles and with clear 804.11(g)(7)
distance of 3D 8' from test pile;
one dial gage mounted on each reference beam approximately equidistant from the center
of and on opposite sides of the test pile with stems parallel to longitudinal axis of the pile
and bearing on lugs firmly attached to the sides of the pile below the test plate (or
equivalent mounting scheme)
pile axial movements shall be measured and recorded to the 0.001" 804.11(g)(4)
Load to 3 times design value or until plunge occurs 804.11(g)(1)
apply loads in increments of 10 to 15% of design load with a constant time interval of 5
minutes or as otherwise specified, add load increments until continuous jacking is required
804.11(g)(1)
loading
to maintain the test load or until the specific capacity is reached, at which time stop the
jacking
full test load to be removed in four approximately equal decrements with 5 minutes
between decrements, final recovery recorded so shape of rebound curve may be 804.11(g)(1)
determined
readings
take readings of time, load, and settlement and record immediately at intervals specified,
804.11(g)(1)
when max load applied take readings after jacking has stopped, except for final recovery
for final recovery record 30 minutes after movement essentially complete 804.11(g)(1)
re-stike restrike after 24 hours from loading if required by Geotechnical Section 804.11(e)
ASTM
D1143
5( c )(2)
3.1.2
3.1.3
3.3.1
3.1.4
3.1.5
3.1.6
7.1.3
3.2.2
3.2.5
3.2.3
3.1.2
4.1.2
4.1.1
4.2.1
4.4.2
5.6.2
5.6.3
6.4