Model BCF
Belt Drive Low-Prole
November
2014
Model BCF
Centrifugal Cabinet Fan
Contents
Standard Construction Features ....................... 3 Typical Installations ........................................... 5
Options and Accessories .................................. 4 Dimensions and Performance ..................... 6-15
Filter and Mixing Box Data ................................ 5 Typical Specifications .................................... 16
Model Comparison
Drive
Location Mounting Airow Application Impeller Type Performance
Type
Maximum Volume
Model
General/Clean Air
Contaminated Air
Ceiling Mounted
Propeller/Axial
Mixed Flow
Recirculate
Centrifugal
Base/Floor
Reversible
Roof Curb
Hanging
Outdoor
Exhaust
(in. wg)
Supply
Indoor
Direct
(cfm)
Wall
Belt
BCF 9 9 9 9 9 9 9 9 9 5,850 1
Belt Drive Low Profile Cabinet Fans Every model has been designed with low-profile
construction to fit within tight spaces, as low as
Greenhecks belt driven low-profile cabinet fan, 11inches (280 mm).
model BCF, is designed for efficiency and reliability Capacities range from 170 to 5,850 cfm (290 to
in supply, exhaust or ducted return applications. 9950 m3/hr) with static pressures up to 1 in. wg
Featuring a compact, rectangular cabinet design, (375 Pa).
model BCF mounts easily in standard duct passages.
Horizontal mounting with either top horizontal or All fan sizes are tested in our AMCA Accredited
upblast discharge allows the BCF to be applied in a Laboratory, and all BCF sizes are licensed to
wide range of air handling applications. bear the AMCA Certified Ratings Seal for Air
Performance.
BCF cabinet fans are available in single and double
fan models. Both feature the combination of a Greenheck subjects these products to extensive
quiet running, forward curved wheel and a well life testing assuring you that the fans will provide
proportioned fan housing for efficiency. In double fan years of reliable performance.
models, each wheel is housed separately, but both Greenheck Fan Corporation certies that the model BCF
are driven by a single motor and shaft. Fan wheels fans shown herein are licensed to bear the AMCA Seal.
The ratings shown are based on tests and procedures
are statically and dynamically balanced to assure performed in accordance with AMCA Publication 211
vibration free operation. and comply with the requirements of the AMCA Certied
Ratings Program. The certied ratings for model BCF are
shown on pages 6 to 15.
Enjoy Greenhecks extraordinary service, before, during and after the sale.
Greenheck offers added value to our wide selection of top performing, energy-efcient products by
providing several unique Greenheck service programs.
Our Quick Delivery Program ensures shipment of our in-stock products within 24 hours of placing your
order. Our Quick Build made-to-order products can be produced in 1-3-5-10-15- or 25-day
production cycles, depending upon their complexity.
Greenhecks free Computer Aided Product Selection program (CAPS), rated by many as the best in
the industry, helps you conveniently and efciently select the right products for the challenge at hand.
Greenheck has been Green for a long time! Our energy-saving products and ongoing corporate
commitment to sustainability can help you qualify for LEED credits.
Our 3D service allows you to download at no charge lightweight, easy-to-use AutoDesk Revit 3D
drawings for many of our ventilation products.
Find out more about these special Greenheck services at greenheck.com
2
Standard Construction Features
Vibration Isolation - Internal true vibration isolators Motor - Ball bearing motors are carefully matched
support the entire drive assembly, wheel, and scroll to the fan load. Open drip proof and totally enclosed
without steel to steel contact. This provides long life enclosures are available.
and quiet operation.
Drive Frame - Constructed from heavy gauge steel
Housing - The fan cabinet is constructed of galvanized and designed with belt adjustment to eliminate scroll
steel for corrosion resistance and maintenance free damage. Adjustment is accomplished by loosening
operation. fasteners, sliding the motor plate, and retightening.
Access Panel - Hinged or removable panels allow Drive Assembly - Belts, pulleys and keys are sized for
for easy access to all internal components. Hinged a minimum of 150% of driven horsepower. Machined
panels are on fan sizes 106, 107, 206 and 207 and cast iron pulleys are factory set to the required RPM
are removable on the larger sizes in both single and and adjustable for final system balancing. Belts are
double fans. static free and oil resistant.
Bearings - Permanently sealed, pillow block ball Fan Shaft - Precisely sized, ground, and polished
bearings are selected for a minimum L10 life in excess so the first critical speed is at least 25% over the
of 100,000 hours (L50 average life of 500,000 hours) at maximum operating speed. Close tolerances between
maximum catalogued operating conditions. the shaft and bearing result in longer bearing life.
Wheel - Forward curved, centrifugal, galvanized Duct Collars - Inlet and outlet duct collars are
steel wheel is utilized to generate high efficiency provided for easy duct connections.
and minimal sound. Each wheel is statically and
dynamically balanced for long life and quiet operation.
Fan
Shaft Duct Collars
Bearings
Drive Frame
Drive
Motor Assembly
3
Options and Accessories
Mixing Boxes - Constructed of galvanized steel and Side Access Doors - For installations where normal
available with or without dampers. Inlet position must access is restricted, removable side access doors
be specified. Any two of the three positions shown are available for ease of inspecting and servicing
(X, Y or Z) may be selected. fan wheels, motors, belts and drives. Door locations
must be specified left or
X
right as viewed from the
discharge end of the fan.
Surrounding ductwork or
other equipment should
Y be considered when
selecting the access door
location.
Z
Insulated Housing - For noise reduction and
condensation control, the interior of fan housings,
mixing box and filter box can be lined with a 1 inch
Filter Boxes - Constructed of galvanized steel. fiberglass duct liner.
Available with either a sloped filter arrangement or
vertical slide-out. Smaller fan sizes (106, 107, 206 and Disconnect Switches - A
207) have a sloped single angled filter. The double- wide selection of NEMA rated
vee configuration is used with all larger sloped sizes. switches are available for
Filters are available in 1 or 2-inch disposable media positive electrical shutoff and
or permanent, washable aluminum mesh. Filter boxes safety. This includes general,
with slide-out have 2-inch washable aluminum filters. dust-tight, rainproof, and
corrosion-resistant.
Sloped, Single Angled Filter - Sizes 106, 107, 206 and 207 Vibration Isolators - Base and hanging isolator kits
are available with either neoprene or spring isolators.
Kits range in size to support either the weight of the
fan alone or the weight of the fan with filter and mixing
box combinations. Kits are for horizontal mounting and
include mounting brackets and hardware. Knockouts
are provided in the fan cabinet for ease of installation.
(Hanging rods supplied by others.)
Sloped, Double-Vee Filter - Sizes 108, 110, 112, 208, 210 and 212
Hanging Spring
Neoprene
Standing
Spring
Hanging Neoprene
Slide-Out, Aluminum Filter - Sizes 106 thru 212 Wiring Pigtail - Allows direct hook-up to the power
supply externally (eliminating field wiring at the fan).
4
Filter and Mixing Box Data
D
C
Mixing Box
Filter Box
Fan
B
A
Typical Installations
Model BCF fans are available with either top horizontal or upblast discharge positions. To select the most
effective fan position and discharge, it is necessary to consider the direction of air entering the fan and the
direction of exhausted air. All of the accessories shown on page four can be used with the installations shown.
In order to assure proper fan performance, caution must be exercised in fan placement and connection.
Obstructions, transitions, poorly designed elbows, etc., can cause reduced performance, excessive noise, and
increase mechanical stress. For performance to be as published, the system must provide uniform and stable
airflow into the fan.
Good Poor
Airflow should discharge in the same direction as Do not install fans with ductwork directing airflow
the wheel rotation. Provide uniform airflow to the fan in the opposite direction of wheel rotations. Avoid
inlet. Use turning vanes in elbows to reduce adverse sharp turns, poorly designed elbows, and transitions
effects where needed. which cause uneven airflow.
5
BCF-106 - Belt Drive
12 (305)
11
(279)
6 6 (152)
(152)
1 (25)
urve
c
ystem
23 (591) 12 (305)
s
20 (508)
this
f t of
e le
h
to t
^Approximate Unit Weight = 80 lb. (36 kg)
ec t
All dimensions in inches (millimeters).
tsel
^Weight shown is largest cataloged Open Drip Proof motor.
no
Do
Maximum RPM = 2468
Tip Speed (ft/min.) = RPM x 1.505
Maximum Motor Frame Size = 56
Average Outlet Velocity (FPM) = CFM/0.5 ft2
5/8 (16)
13
8 (330)
8 (203)
(203)
1 (25)
ve
cur
29 (737) 15 (381)
tem
23 (584)
ssys
thi
tof
lef
he
^Approximate Unit Weight = 100 lb. (45 kg)
ot
tt
All dimensions in inches (millimeters).
l ec
se
^Weight shown is largest cataloged Open Drip Proof motor. t
no
Do
Maximum RPM = 1915
Tip Speed (ft/min.) = RPM x 1.955
Maximum Motor Frame Size = 56
Average Outlet Velocity (FPM) = CFM/0.83 ft2
5/8 (16)
16
10 (406)
10 (254)
(254)
1 (25)
e
curv
18 (457)
stem
32 (813)
26 (660)
is sy
h
of t
left
the
^Approximate Unit Weight = 120 lb. (54 kg)
to
All dimensions in inches (millimeters).
t
lec
se
^Weight shown is largest cataloged Open Drip Proof motor. t
no
Do
Maximum RPM = 1578
Tip Speed (ft/min.) = RPM x 2.235
Maximum Motor Frame Size = 56
Average Outlet Velocity (FPM) = CFM/1.25 ft2
5/8 (16)
19
12 (483)
12 (305)
(305)
1 (25)
urve
c
em
36 (914) 24 (610)
syst
32 (813)
h is
of t
left
he
^Approximate Unit Weight = 265 lb. (120 kg)
t
to
ct
All dimensions in inches (millimeters).
ele
ts
^Weight shown is largest cataloged Open Drip Proof motor. n o
Do
Maximum RPM = 1426
Tip Speed (ft/min.) = RPM x 2.589
Maximum Motor Frame Size = 143T
Average Outlet Velocity (FPM) = CFM/2.0 ft2
5/8 (16)
23
14 (584)
(356) 14 (356)
1 (25)
e
cu r v
em
42 (1067) 28 (711)
syst
36 (914)
his
of t
left
the
^Approximate Unit Weight = 340 lb. (157 kg)
tot
All dimensions in inches (millimeters).
lec
se
^Weight shown is largest cataloged Open Drip Proof motor.
ot
n
Do
Maximum RPM = 1294
Tip Speed (ft/min.) = RPM x 3.045
Maximum Motor Frame Size = 182T
Average Outlet Velocity (FPM) = CFM/2.72 ft2
11
(279)
6 (152)
6
(152)
1 (25)
e
curv
26 (660)
m
23 (591) 34 (864)
yste
is s
f th
ft o
le
he
^Approximate Unit Weight = 145 lb. (66 kg)
t
to
ct
All dimensions in inches (millimeters).
el e
ts
^Weight shown is largest cataloged Open Drip Proof motor. no
Do
Maximum RPM = 2427
Tip Speed (ft/min.) = RPM x 1.505
Maximum Motor Frame Size = 56
Average Outlet Velocity (FPM) = CFM/1.08 ft2
13
(330)
8 (203)
8
(203)
1 (25)
e
ur v
30 (762)
mc
29 (737) 38 (965)
yste
is s
f th
to
lef
he
^Approximate Unit Weight = 185 lb. (84 kg)
ot
tt
All dimensions in inches (millimeters).
lec
se
^Weight shown is largest cataloged Open Drip Proof motor. t
no
Do
Maximum RPM = 1803
Tip Speed (ft/min.) = RPM x 1.955
Maximum Motor Frame Size = 143T
Average Outlet Velocity (FPM) = CFM/1.67 ft2
16
(406)
10 10 (254)
(254)
1 (25)
e
36 (914)
urv
32 (813)
mc
44 (1118)
ste
s sy
thi
of
ef t
l
^Approximate Unit Weight = 220 lb. (100 kg)
he
ot
tt
All dimensions in inches (millimeters).
ec
l
ts
e
^Weight shown is largest cataloged Open Drip Proof motor. o
D on
Maximum RPM = 1619
Tip Speed (ft/min.) = RPM x 2.235
Maximum Motor Frame Size = 145T
Average Outlet Velocity = CFM/2.5 ft2
19
(483)
12 (305)
12
(305)
urve
1 (25)
40 (1016)
c
stem
36 (914) 48 (1219)
i s sy
f th
ft o
le
the
^Approximate Unit Weight = 345 lb. (156 kg)
t to
lec
All dimensions in inches (millimeters).
tse
no
^Weight shown is largest cataloged Open Drip Proof motor.
Do
Maximum RPM = 1429
Tip Speed (ft/min.) = RPM x 2.589
Maximum Motor Frame Size = 182T
Average Outlet Velocity = CFM/3.33
23
(584)
14 (356)
14
(356)
1 (25)
e
c ur v
50 (1270)
stem
42 (1067) 58 (1473)
is sy
h
of t
left
the
^Approximate Unit Weight = 515 lb. (234 kg)
to
ct
All dimensions in inches (millimeters).
s e le
^Weight shown is largest cataloged Open Drip Proof motor.
ot
n
Do
Maximum RPM = 1271
Tip Speed (ft/min.) = RPM x 3.045
Maximum Motor Frame Size = 184T
Average Discharge Velocity (FPM) = CFM/4.56
Fan Type
Duct mounted supply, exhaust or return fans shall be of the centrifugal, belt driven,
inline type. The fan housing shall be of the rectangular design constructed of heavy
gauge galvanized steel and shall include rectangular duct mounting collars.
Hinged Panel
A hinged or removable panel shall be provided in the fan cabinet of sufficient size to
permit access for service to all of the fans internal components without dismantling
the cabinet.
Fan Wheel
The fan wheel shall be of the galvanized steel, forward curved, centrifugal type.
Wheels shall be dynamically and statically balanced.
Motors
Motors shall be of the heavy duty type with permanently sealed ball bearings. The
wheel shaft shall be ground and polished steel mounted in permanently sealed
pillow block bearings. Drives shall be sized for a minimum of 150% of driven
horsepower. Pulleys shall be of the machined cast iron type, keyed and securely
attached to the wheel and motor shafts. The motor pulleys shall be adjustable for
final system balancing.
AMCA
All fans shall bear the AMCA Certified Ratings Seal for Air Performance.
Manufacturing
Fans shall be model BCF as manufactured by Greenheck Fan Corporation in
Schofield, Wisconsin, USA.
Our Commitment
As a result of our commitment to continuous improvement, Greenheck reserves the right to change
specifications without notice.
Specific Greenheck product warranties are located on greenheck.com within the product area tabs
and in the Library under Warranties.
Prepared to Support
Green Building Efforts
00.F&V.1014 R3 11-2014 SN
P.O. Box 410 Schofield, WI 54476-0410 Phone (715) 359-6171 greenheck.com Copyright 2014 Greenheck Fan Corp.