Product Specifications
PSS 21H-2W6 B4
DIN Rail Mounted Modular Baseplates
The DIN rail mounted Modular Baseplates provide the mounting platform and communication backplane for
DIN rail mounted modules.
Keyed positions dedicated to FCP270 or Field Control Processor 270 (FCP270) fault-
FCM/FBM only tolerant or non-fault-tolerant
Passive backplane to increase system reliability. Field Communications Modules (FCM100Et and
FCM100E) and other FCMs
OVERVIEW Fieldbus Expansion Modules (FEM100E)
The Modular Baseplates enable overall system
Fieldbus Isolator/Filter Modules (FBI100)
installation functionality by providing unit increments
of 2, 4, and 8 module positions in combination with DIN rail mounted Fieldbus Modules (FBMs) and
vertical and horizontal mounting. 100 Series FBMs connection.
These Modular Baseplates support distributed
control for both small and large systems and
MODULAR BASEPLATE MOUNTING
specifically support the following I/A Series system Most Modular Baseplates are available in two basic
DIN rail mounted modules: mounting configurations horizontal DIN rail mount
(see Figure 1) or vertical DIN rail mount (see Figure 2).
Field Control Processor 280 (FCP280) fault-
Either of these mounting configurations can be
tolerant or non-fault-tolerant
employed internal to an enclosure, external to an
enclosure, or mounted on a secure DIN rail.
FCP280 only FCP270 only 1 FCP270 and 3 FBM 2 FCP270 and 2 FBM
2-position, RH924YL 2-position, P0926HC 4-position, P0926HJ 4-position, P0926HF
FCP280 only
2-position,
RH924YF
2 FCP270
and 2 FBM
4-position,
FCP270 only
P0926HZ
2-position,
P0926HW FBM
and/or FCM
8-position,
FCM/FBM P0926JM
2-position,
P0926KH
1 FCP270
and 3 FBM
4-position,
P0926JC
FBM
and/or FCM
4-position,
P0926JF 2 FBI200
2 FCP270 2-position,
and P0924RT
2 FEM100
4-position
P0973CN
FEM100 only
2-position, 2 FBI100
P0973CG 2-position,
P0923LR
MODULE IDENTIFICATION The letterbug string for a particular FBM when used
The baseplate-mounted FBMs, FCM10E, or with FCMs is established from these three factors:
FCM10Ef are identified to the system software by The first four characters of the FCM10E,
means of a unique, 6-character string called a FCM10Ef, FCM100Et or FCM100E letterbug.
letterbug. Most baseplates include a DIP switch to The number of the baseplate in the group, as set
help set this letterbug for the FBMs. by means of the baseplate Identification (I.D.) DIP
The letterbug for the FCP280s is a soft letterbug switches on each baseplate (see Figure 3).
entered via the buttons on the modules faceplate. Baseplates should be assumed to have this
The letterbug for the FCP270s, FCM100Ets and switch unless otherwise specified in the sections
FCM100Es is a soft letterbug entered using the below.
I/A Series Letterbug Configurator.
PSS 21H-2W6 B4
Page 4
The physical position (1-8) of the module on the MODULAR BASEPLATE COMBINATIONS AND
baseplate. IMPLEMENTATION
The letterbug string for a particular FBM when used The Modular Baseplates support the:
with the FCP280 or FCP270 is established from FCP280
these four factors:
FCP270 with optional Fieldbus Expansion
The first four characters of the letterbug, which Modules (FEMs)
may be any letter A-Z or digit 0-9 as long as they
Field Communications Modules (FCMs)
do not match the first four characters of the
FCP280 or FCP270 letterbug. Fieldbus Isolator/Filters (FBI200s and FBI100s)
The number of the baseplate in the group, as set Fieldbus Modules (FBMs).
by means of the baseplate Identification (I.D.) DIP
switches on each non-FCP280 baseplate (see A combination of FCPs and FBMs, FCPs and FEMs,
Figure 3). Baseplates should be assumed to have FCMs and FBMs, or all FBMs can be mounted on
the Modular Baseplates.
this switch unless otherwise specified below.
For the FCP270 used with the FEM100, this is a Various sizes of Modular Baseplates allow you to
hexadecimal number as these configurations can incrementally upgrade existing systems or to create
support up to 16 baseplates for one control small systems. Implementation of these Modular
processor, via 1-4 expansion ports. Baseplates allow you to place the control processor
The physical position (1-8) of the module on the (FCP280 or FCP270) within the same enclosure as
baseplate. other FBMs.
The FCP270 module position(s) on Modular
Baseplates for mounting the FCPs are keyed
positions preventing FBM/FCM/FEM modules from
plugging into the FCP mounting position.
Each Modular Baseplate and its supported
functionality is described below.
a single module or redundant pair of FBI100s. supports a redundant pair of FEM100s. This
baseplate does not have a baseplate identification
FCP280 Only 2-Position Baseplate (see Figure 1
and Figure 2) DIP switch, as it does not require a hardwired
address.
These 2-position baseplates support a non-fault-
tolerant single or fault-tolerant pair of FCP280s, as This Expansion Baseplate can be added to existing
well as two copper (RH924UQ) or fiber (RH924WA) FCP 2-position Modular Baseplates. It is used to
adapters, required for connection to The Mesh expand the number of 200 Series FBMs supported
control network. by a FCP270, by providing the capability to add up
to four Expanded Fieldbuses which each can support
The FCP280 baseplate provides support for four
up to thirty-two 200 Series FBMs.
HDLC fieldbuses (PIO channels). Fieldbus port 1 can
be terminated, if needed, by the DIP switches FBI200 and FBI100 2-Position Baseplates (see
provided on the baseplate. Fieldbus ports 2-4 are Figure 2)
internally terminated in the FCP280 baseplates and The FBI200 2-position vertical baseplate support a
no external hardware or switches are required for redundant pair of FBI200s, and the FBI100
their termination. 2-position vertical baseplate supports a redundant
pair of FBI100s. These Modular Baseplates do not
The FCP280 baseplates can be added in the field to
have a baseplate identification DIP switch, as they do
existing or new configurations. They have similar
not require a hardwired address. The FBI200
dimensions as the FCP270 Only 2-position
2-position vertical baseplate does have DIP switches
baseplates for ease of replacement.
for baud rate mode selection.
When upgrading existing CP60 systems to use
FCM/FBM 2-Position Modular Baseplate (see
FCP280s, you can recover an additional two FBM
Figure 1 and Figure 2)
positions after removal of the old
These 2-position Modular Baseplates support
FCM10E/FCM10Efs.
FCMs/FBMs. These Modular Baseplates do not have
FCP270 Only 2-Position Modular Baseplate (see a baseplate identification DIP switch. Therefore,
Figure 1 and Figure 2)
these baseplates have a hardwired address as
These 2-position Modular Baseplates support a non- baseplate 0, with FBM addresses 1 and 2. They can
fault-tolerant single or fault-tolerant pair of FCP270s.be added to existing or new groupings of Modular
Mounting space is provided for the fiber optic
Baseplates.
splitter/combiners that support a fault-tolerant pair of
FCP270's. These Modular Baseplates do not have a 4-Position Modular Baseplates
baseplate identification DIP switch. Therefore, these
Seven different 4-position Modular Baseplates
baseplates have a hardwired address as baseplate 0.
support:
These Modular Baseplates can be added to existing
a fault-tolerant pair of FCP270s in two positions
or new groupings of Modular Baseplates. They can
and the remaining two positions mount FEM100s
be used to upgrade existing systems with FCP270s
a fault-tolerant pair of FCP270s in two positions
or to support FCP270s in a new system.
and the remaining two positions mount FBMs
FEM100 Only 2-Position Expansion Baseplate (see a single FCP270 in one position and the
Figure 2)
remaining three (non-fault tolerant) positions
This 2-position vertical Expansion Baseplate mount FBMs
PSS 21H-2W6 B4
Page 6
4 FBMs or 2 FCMs and 2 FBMs. mount FBMs. These Modular Baseplates have a
The following applies to these baseplates, with the baseplate identification DIP switch.
exception of the FCP270/FEM100 baseplate: These Modular Baseplates can be used on system
installations that require increased I/O distribution
These baseplates have horizontal and vertical
and future upgrades. They are intended to support
versions.
small system requirements where fault tolerant
These baseplates have three active baseplate I.D.
control is not a requirement.
switches. The third baseplate I.D. switch selects
operation as the first-half or second-half of an 8- FBM and/or FCM 4-Position Modular Baseplates
position Modular Baseplate. (see Figure 1 and Figure 2)
These 4-position Modular Baseplates supports
FCP270 and FEM100 4-Position Expansion
FBM/FCMs. These Modular Baseplates have a
Baseplate (see Figure 2)
baseplate identification DIP switch.
This Expansion Baseplate is a 4-position Modular
These Modular Baseplates can be used on system
Baseplate that supports a fault-tolerant pair of
installations that require increased I/O distribution
FCP270s in two positions and the remaining two
and future upgrades.
positions mount a redundant pair of FEM100s.
Mounting positions are provided for the fiber optic
8-Position Modular Baseplates
splitter/combiners to support the pair of FCP270's.
(see Figure 1 and Figure 2)
This Modular Baseplate does not have a baseplate
These 8-position Modular Baseplates support
identification DIP switch.
FBMs/FCMs. These Modular Baseplates have a
This Modular Baseplate can be used on system baseplate identification DIP switch.
installations that require increased I/O capabilities
These Modular Baseplates mount up to 32 FBMs
and future upgrades.
(four 8-position baseplates) in a standard enclosure.
FCP270 and FBM 4-Position Modular Baseplates They supersede the P0914XA/XB baseplates and
(see Figure 1 and Figure 2) maximize module/baseplate density.
These Modular Baseplates are 4-position Modular For Intrinsically Safe applications, the use of Pepperl
Baseplates that support a fault-tolerant pair of and Fuchs Intrinsic Safe baseplates is
FCP270s in two positions and the remaining two recommended. Refer to Intrinsically-Safe
positions mount FBMs. Mounting positions are Combination Termination Assemblies and Baseplates
provided for the fiber optic splitter/combiners to (ISTA*BP*) (PSS 21H-2Y12 B4).
support the pair of FCP270's. These Modular
Baseplates have a baseplate identification DIP
switch.
These Modular Baseplates can be used on system
installations that require increased I/O distribution
and future upgrades.
Single FCP270 and FBM 4-Position Modular
Baseplates (see Figure 1 and Figure 2)
These Modular Baseplates support a single FCP270
in one position and the remaining three positions
PSS 21H-2W6 B4
Page 7
MODULAR BASEPLATE INTERCONNECTIONS into the Modular Baseplate. Primary and Secondary
Modular Baseplates are interconnected over a power connectors are direct connections from the
2 Mbps HDLC, redundant, serial bus (Module FPS400-24, FPS240-24, or FPS120-24 power
Fieldbus). All Modular Baseplate inter-connections for supply. Field I/O connectors provide connections to
A/B Module Fieldbus connections are shielded various termination assemblies for actual connection
twisted-pair cables to reduce the effects of noise. to the I/O points in the plant.
All connectors are labeled to indicate their position FCM2F2/4/10 modules provide for fiber optic
and/or function on the Modular Baseplates extension (baseplate-to-baseplate) of the Module
(see Figure 4). All module connectors have module Fieldbus.
guides to ensure the correct insertion of the module
Module Connectors
Field I/O Connectors
In addition, another type of termination assembly support for two of their associated FBMs in paired
called the baseplate-mounted termination assembly slots (that is, in positions 1 and 2, 3 and 4, 5 and 6,
can mount directly onto the field I/O connectors of a or 7 and 8), as shown in Figure 5.
Modular Baseplate. These TAs provide field I/O wiring
01 01
02 02
03 03
04 04
DI/DO, Pulse HART DI/DO, Pulse HART
05 05
06 06
07 07
08 08
FBM247 FBM247
Channel Isolated Channel Isolated
8 Configurable Channels 8 Configurable Channels
(AI/AO)+HART, DI/DO, Pulse (AI/AO)+HART, DI/DO, Pulse
P0927BN P0927BN
Baseplate Mounted
Termination Assembly
(P0916RB)
(RH928CV -
FCP280 Baseplate
(P0926KW) FCP280 Only)
Fieldbus Port
Connector
Fieldbus B Fieldbus A
ADDING ADDITIONAL MODULAR system have redundant (A and B) buses. A/B Module
BASEPLATES Fieldbus and Time Strobe splitter/terminators are
You can add additional Modular Baseplates to used to split the A/B Module Fieldbus (2 Mbps)
existing Modular Baseplates without removing the allowing redundant baseplate-to-baseplate cabling
system from service. To add Modular Baseplates as well as the addition of Modular Baseplates without
while the system is operational requires that the interrupting bus communication.
F U N C T I O N A L S P E C I F I C AT I O N S
E N V I R O N M E N TA L S P E C I F I C AT I O N S ( 1 )
Operating Storage
TEMPERATURE TEMPERATURE
-20 to +70C (-4 to +158F) -40 to +70C (-40 to +158F)
RELATIVE HUMIDITY RELATIVE HUMIDITY
5 to 95% (noncondensing) 5 to 95% (noncondensing)
ALTITUDE ALTITUDE
-300 to +3,000 m (-1,000 to +10,000 ft) -300 to +12,000 m (-1,000 to +40,000 ft)
Contamination (Non-Enclosure Mounted)
Class G3 (Harsh) as defined in ISA Standard S71.04
Contamination (Enclosure Mounted)
Class G3 (Harsh) as defined in ISA Standard S71.04.
Pollution degree 2 as defined in IEC 664-1.
P H Y S I C A L S P E C I F I C AT I O N S
(1) The environmental limits of the Modular Baseplates may be enhanced by the type of enclosure containing the Modular
Baseplate.[Refer to the applicable Product Specification Sheet (PSS) which describes the specific type of enclosure that is to be used.
(2) For dimensions of the FCP280, refer to PSS 31H-1B11 B3. For dimensions of the FCP270, refer to PSS 21H-1B9 B3.
PSS 21H-2W6 B4
Page 14
120.3
4.74
240.0
9.10
8-POSITION
Total Minimum
Clearance
180 27.1
7.08 97.7 1.07
3.8
453.0 30.3
17.83 1.19
7.5
.30
216.0
8.5
252.4
9.9
NOTE: Clearance dimensions shown for 200 Series Fieldbus Modules installed in baseplates. For the clearance dimensions required
for larger modules such as the FCP280 and FCP270, refer to the Product Specification Sheet associated with these larger
modules. Cable clearance is the same for both 200 Series FBMs and other modules, such as the FCP280 and FCP270.
2-POSITION 4-POSITION
120.3 240.0
4.74 9.10 [ mm ]
SIDE VIEW in
27.1 7.5
8-POSITION 1.07 .30
75.0
3.0
Cable
Clearance
216.0
8.5 252.5
9.94
Rack Mount
Without End Caps
443.0
17.44 30.3
1.19
453.0
17.83 97.7
3.85
180.0
7.09
Total Minimum
Clearance
Baseplate-Mounted Termination Assembly Shown Mounted on Baseplate (Optional) - Increases Baseplates Height if Installed
NOTE: Clearance dimensions shown for 200 Series Fieldbus Modules installed in baseplates. For the clearance dimensions required
for larger modules such as the FCP280 and FCP270, refer to the Product Specification Sheet associated with these larger
modules. Cable clearance is the same for both 200 Series FBMs and other modules, such as the FCP280 and FCP270.
Invensys Invensys, Foxboro, I/A Series, and the Invensys logo are
10900 Equity Drive trademarks of Invensys plc, its subsidiaries, and affiliates.
Houston, TX 77041 All other brands and product names may be the
United States of America trademarks of their respective owners.
http://invensys.com
Copyright 20042013 Invensys Systems, Inc. All rights
reserved. Unauthorized duplication or distribution is strictly
Global Customer Support prohibited.
Inside U.S.: 1-866-746-6477
Outside U.S.: 1-508-549-2424 or contact
your local Invensys representative.
Website: http://support.ips.invensys.com MB 21A 1213