Version 17/11/03
SikaMonoTop-615HB
Light Weight Repair Mortar
SikaMonoTop-615HB 1/3
D06297030902E
Technical Data Mixing SikaMonoTop-615HB can be hand mixed in small amounts. (easily up to
3 kg of powder). Fill sufficient clean water into a small container. Add
Colour Concrete Grey
SikaMonoTop-615HB to the water and hand mix thoroughly with a
spatula or trowel until a smooth workable consistency is achieved. Always
Density Dry - 1.15kg/litre (bulk density of powder)
respect the water : powder ratio (1 part of water for 5.5-5.8 parts of
Mixer - 1.67kg/litre (density of fresh mortar)
powder by volume). If a mix has thickened due to delayed application,
do not dilute further with water.
Mixing Ratio 3.00-3.20 litres of clean water per 20 kg bag to suit desired consistency
Water : Powder =1 : 6.3 - 6.6 parts by weight For large repairs, mechanical mixing (of the whole bag) using a drill
1 : 5.5 - 5.8 parts by volume and a paddle is advisable. Pour water in given quantity in a clean drum
and add SikaMonoTop-615HB slowly while mixing. Use a low speed
o
Pot Life (30 C) approx. 20 minutes electric mixer for 3 minutes avoiding entrapped air. Follow the ratio 3 to
3.2 Ltr of water per 20 kg bag.
Application Thickness Minimum 5 mm Application -SikaMonoTop-615HB can be applied by wet-spray equipment or manually
Maximum 50mm (overhead application) by trowelling.
Maximum 60mm (vertical application) -If, in the area to be repaired, steel reinforcement is exposed, SikaMonoTop-610
o o
reinforcement protective coating, must be applied in two layers (refer to
Application Temperatures Optimal range : between 5 C and 35 C SikaMonoTop-610 datasheet).
-SikaMonoTop-615HB has a good bond strength to the concrete.However,
Mechanical Strengths 1 day 28 days SikaMonoTop-610 can be used as a bonding agent for achieving highest
o
(25 C) Compressive: 10 MPa 25 MPa mechanical performances. The application of SikaMonoTop-615HB onto
the bonding bridge SikaMonoTop-610 must be wet on wet.
Bond Strength >1.5 N/mm2 (with substrate preparation) -For thickness greater than 60 mm on vertical surface, SikaMonoTop-615HB
must be applied in several layers.
Shelf Life 12 months when unopened - As soon as the mortar has started to set, it can be smoothed by wooden
or synthetic float or a styrofoam block
Storage Condition Store in a dry cool place .
Curing - Sika MonoTop -615HB cures with low shrinkage. To prevent premature
Packaging 20 kg bags drying out of the mortar, keep it moist if exposed to strong sunshine as wind
- Standard curing methods are recommended.
Instruction For Use High quality, long term repairs can only be achieved if they are carried out - For very fine surface finish, the application of Sika Refit L is
conscientiously by experienced applicators giving adequate attention to details advised.
relating to surface preparation, priming of concrete and steel, mixing of repair Consumption Guide For 1 ltr. of fresh mortar approx. 1.45 kg. of powder are required.
mortars, application and curing.
Cleaning Remove non hardened SikaMonoTop products from tools and equipment
Substrate Preparation Substrate must be sound, free of loose or weak particles, dust and dirt. with water. Hardened material can only be removed mechanically.
Oil and wax containing layers, as well as laitance must be completely removed. Safety Instructions
The substrate must be throughly wetted down prior to the mortar applica-
Safety precautions SikaMonoTop-615HB is caustic (cement). Protect skin and eyes from
t i o n . contact with mortar. Wear protective clothing and goggles while working
with the product.Should the material enter the eyes, rinse immediately with
clean water and seek medical attention.
Toxicity Non-toxic
Transport Non-hazardous.
SikaMonoTop-615HB 3/3
SikaMonoTop-615HB 2/3