BILL OF QUANTITY
GENERAL NOTES:
All works and installations listed here below should be carried out, tested
and commissioned by specialized responsible contractor by coordination
with Beit Hanoun Municipality and CMWU, all in accordance with
drawings, specifications and relevant standards, and the instruction of the
Supervisor Engineer. The Engineer has the right to reject any component
of the work not complying with the specifications and the requirement of
the contract.
The contractor should provide for all discrepancies and arrange for all
mechanical and electrical materials, fittings and accessories that may
require completing the installations properly, and any necessary works
to install the equipments properly as specified, shown on the Drawings
and directed by the Supervisor Engineer.
Complete detailed shop drawings should be delivered to the Engineer
to take his approval prior the commencement of work. Samples of all
materials shall also be delivered to the Engineer to take his approval,
The price for underground pipes and connections works shall include
excavation, leveling, compaction, pipes laying including all piping
works such as proper jointing, welding, cutting and shaping, testing,
disinfection, required microbiological tests, bedding material under,
surrounding, and above the pipe with clean dune sand, backfilling by
supplying proper and approved material or with suitable and approved
selected excavated materials, the backfilling should be on layers not
exceed than 20cm with compaction, removing surplus excavation
material outside the site to places as instructed by the Engineer, and
reinstatement to original condition of all roads and areas used or
disturbed by the Contractor to the satisfaction of the Engineer. The
price shall include execute thrust blocks for elbows, teesetc. and all
other necessary works, all above should be according to the drawings,
specification, standards and under the supervision and direction of the
Engineer.
Wherever, the pipes and connections fittings installed above the
ground (none buried), the pipes connections fittings shall be coated
with three layers of epoxy. The pipes and fittings underground (buried)
shall be coated with epoxy primer and two layers of extruded
polyethylene coating.
Interior surfaces of all steel pipe and fittings shall be lined with cement
mortar lining, factory made.
All used bolts, washers, nuts etc should be made of stainless steel
grade 304.
All replaced, malfunctioning, and/or additional items should be
delivered to a proper location according to the instruction of the
Supervisor Engineer.
For steel shed works, all measurements to be taken on the horizontal
projection. The works include the temporary moving and reconnection
of the existing facilities.
Tiling works shall include, excavation, leveling and preparation,
watering, and compaction up to 98% MDD of all layers including the
sub-grade (after performing any excavation works in general) and base
course layers (not more than 20cm), the works include and the disposal
of surplus excavated material to a proved site, all complete as
described in the Specifications, as shown on the Drawings, and as
directed by the Supervisor Engineer.
Contractor Signature
1
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
Unit
Total
Item Description Unit Qty. Price
(US$)
(US$)
A. ABU GHAZALAH WELL (C128)
1. Civil Works
1.1 Remove the rusty areas of the main gate with
emery paper (sandpaper), the item includes the
removal and replacement of bottom profile (4 m)
and rusty sheets (70100 cm), providing and fixing
approved Wally switch or equivalent, and repaint
the gate with one primer coat and at least three
coats of approved oil paint, all according to
Engineer's instructions. L.S. 1
Contractor Signature
2
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
Unit
Total
Item Description Unit Qty. Price
(US$)
(US$)
1.6 Supply and install steel shed for fuel tank (3.55.5
m, 4.0 m Height) including 4 steel pipes 4 Dia.
3.96mm thick with steel base plate 3003008mm
to be fixed to the existing (35m) concrete
foundation using another steel leveling bearing
plate 3003008mm with suitable Philips bolts
complete with all washers nuts, supports, and all
needed accessories to perform the required works
as per specifications, drawings and the instruction
of the supervisor Engineer. The works include all
sheeting (cladding) works with corrugated steel
sheets 0.55mm with fixation double and single
channels 1004015 of 3mm thick. The item
includes min. 1.0m upper vertical cladding and all
required accessories, bolts, nuts etc, and
painting with one primer coat and three coats of
approved epoxy paint. The item includes the
cleaning, maintenance, and painting the fuel tank
chamber with approved epoxy paint. M2 20
Contractor Signature
3
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
Unit
Total
Item Description Unit Qty. Price
(US$)
(US$)
1.11 Supply and paint super bondrol prime coat and
three coats of emulsion paints (Supercryl) for
internal walls, including all the required materials.
The works include removing the old paint and
cleaning the surface. M2 250
1.13 Supply and paint super lack paint and one primer
coat for doors and windows. The works include
removing the old paint and cleaning the surface. M2 35
2. Mechanical Works
2.1 WaterPumpingUnit:
Dismantle the existing vertical turbine pump
complete. Supply, install and connect to the
electrical board, multistage Vertical Turbine Pump,
Saudi National Pump, KSB, Hamecdash, Paterson
type or equivalent complete with all associated
fittings and accessories recommended for
installations by the pump manufacturer with
electrical motor US motors type or equivalent with
Contractor Signature
4
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
Unit
Total
Item Description Unit Qty. Price
(US$)
(US$)
hollow shaft, 1450rpm, IP55, stator winding fitted
with PT100 temperature sensors. The motor should
be capable to operate the system and should be
selected according to the manufacturer
recommendation.
The unit should be comprised of vertical line shaft
driven turbine pump of cast iron bowls with rubber
bearings, bronze impellers, suction strainer, bronze
line shaft bearings with rubber inserts, including
stainless steel grade (ASTM A582 grade 416 stainless
steel) 1 Dia. column drive shafts, and epoxy
painted steel column pipes 6 diameter. Sch. 40
(min thick 7.92 mm) with minimum total length of
82m, well head foundation, steel discharge head
6/6 epoxy painted, and 3 galvanized steel pipe
for measuring water level, in addition to any
fittings and components required for the
satisfactory operation of the system and all
necessary works according to specifications,
drawings, and instructions by the Engineer.
The works, installations and prices should include
for all mechanical pipe work installations,
electrical installations with cables including
builders work installations with all associated
reinforced concrete plinths specified by the
manufacturer's installation manual.
The operating point of the pump is (115) M3/hr at
a total dynamic head (TDH) of 88m at minimum
78% pump efficiency. The pump largest diameter
must not exceed 8. L.S. 1
Contractor Signature
5
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
Unit
Total
Item Description Unit Qty. Price
(US$)
(US$)
2.2.2 Supply and install 2 double action PN16 Air
Release Valve A.R.I type or equivalent with all
necessary fittings including 2 ball valve. Unit 1
Contractor Signature
6
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
Unit
Total
Item Description Unit Qty. Price
(US$)
(US$)
2.2.14 Supply and install aboveground 6'' 45o Steel
Elbow, complete all as shown on the Drawings and
as directed by the Engineer. No. 1
2.4 Remove the rusty areas with sandy paper for Fuel
tank and repaint with one primer coat and at least
three coats of approval epoxy paint. The item
includes the inside cleaning of the tank according
to the instructions of the Engineer, and filling the
tank with (5000 l) approved fuel up to its full
capacity. L.S. 1
3. Electrical Works
General:
The Installation of electrical combinations is
outside plastering, except if stated that the work is
installed instead of an old one.
3.1 Supply and install 236w fluorescent lighting
fixture per Gaash including wiring 1.5mm2, 3/4"
plastic pipes, clamps and all accessories to
complete the job outside plastering .
No. 3
Contractor Signature
8
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
Unit
Total
Item Description Unit Qty. Price
(US$)
(US$)
3.13 Supply and install 2x40A earth leakage circuit
breaker per Siemens including all accessories to
complete the job. No. 1
Contractor Signature
9
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
Unit
Total
Item Description Unit Qty. Price
(US$)
(US$)
B. A'AYDA WELL (C20)
1. Civil Works
1.1 Remove the rusty areas of the main gate with emery
paper (sandpaper), the works include the provision
of the required maintenance and replacement of
deteriorated parts, and repaint the gate with one
primer coat and at least three coats of approved oil
paint, all according to Engineer's instructions. L.S. 1
1.2 Remove the rusty areas with sandy paper for the
stairs handrail and repaint with one primer coat and
at least three coats of approval oil paint according
to Engineer's instructions. L.S. 1
1.3 Construct walkways interlock tiles (B300) 6cm
thick including 10 cm base coarse with 5 cm sand
and chamfered edge reinforced concrete beam
(B250) 2030cm 412 and 8@20cm stirrups.
Levels, colors and shapes all determined according
to drawings, specifications and the supervisor
Engineer's instructions. M2 50
1.4 Supply and install steel shed for the Generator
(3.55.5 m, 4.0 m Height) including 4 steel pipes 4
Dia. 3.96mm thick with steel base plate
3003008mm to be fixed to the existing (35m)
concrete foundation using another leveling bearing
steel plate 3003008mm with Philips bolts
complete with all washers nuts, supports, and all
needed accessories to perform the required works as
per specifications, drawings and the instruction of
the supervisor Engineer. The works include all
sheeting (cladding) works with corrugated steel
sheets 0.55mm with fixation double and single
channels 1004015 of 3mm thick. The item
includes min. 1.0m upper vertical cladding and all
required accessories, bolts, nuts etc, and painting
with one primer coat and three coats of approved oil
paint. M2 20
1.5 Supply and install steel shed for fuel tank
(3.55.5m, 4.0m Height) including 4 steel pipes 4
Dia. 3.96 mm thick with steel base plate
3003008mm to be fixed to the existing concrete
foundation using steel bearing plate 3003008mm
with suitable Philips bolts complete with all
washers, nuts, supports, and all needed accessories
to perform the required works as per specifications,
drawings and the instruction of the supervisor
Engineer. The works include all sheeting (cladding)
works with corrugated steel sheets 0.55mm with
fixation double and single channels 1004015 of
3mm thick. The item includes min. 1.0m vertical
Contractor Signature
10
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
Unit
Total
Item Description Unit Qty. Price
(US$)
(US$)
corrugated sheets and all required materials as per
drawing, and painting with one primer coat and
three coats of approved oil paint.
The works include the cleaning, maintenance and
the adjustment of the tank slope in the direction of
the drain valve, and painting the fuel tank chamber
with minimum 3 coats of approved epoxy paint, all
according to the instructions of the Engineer. M2 20
1.15 Supply and paint super lack paint and one primer
coat for doors and windows. The works include
removing the old paint and cleaning the surface. M2 15
2. Mechanical Works
2.1 WATER PUMPING UNIT:
Dismantle the existing vertical turbine pump
complete including the motor. Supply, install and
connect to the electrical board, multistage Vertical
Turbine Pump, Saudi National Pump, KSB,
Hamecdash, Paterson type or equivalent complete
with all associated fittings and accessories
recommended for installations by the pump
manufacturer with electrical motor US motors type
or equivalent with hollow shaft, 1450rpm, IP55,
stator winding fitted with PT100 temperature
sensors. The motor should be capable to operate the
system and should be selected according to the
manufacturer recommendation.
The unit should be comprised of vertical line shaft
driven turbine pump of cast iron bowls with rubber
bearings, bronze impellers, bronze line shaft
bearings with rubber inserts, including stainless
steel grade (ASTM A582 grade 416 stainless steel) 1
Dia. column drive shafts, and epoxy painted steel
column pipes 6 diameter. Sch. 40 (min thick 7.92
mm) with minimum total length of 93 m, well head
foundation, steel discharge head 6/6 epoxy
painted, and 3 galvanized steel pipe for measuring
water level, in addition to any fittings and
components required for the satisfactory operation
of the system and all necessary works according to
specifications, drawings, and instructions by the
Engineer.
The works, installations and prices should include
for all mechanical pipe work installations, electrical
installations with cables including builders work
installations with all associated reinforced concrete
plinths specified by the manufacturer's installation
manual.
The operating point of the pump is (115) M3/hr at a
total dynamic head (TDH) of 95m at minimum 79%
pump efficiency. The pump largest diameter must
not exceed 8. L.S. 1
Contractor Signature
13
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
Unit
Total
Item Description Unit Qty. Price
(US$)
(US$)
2.2 PUMPING MANIFOLD AND CONNECTIONS:
General:
The works include the complete dismantling and
replacement of existing 8 manifold with new and
complete epoxy painted carbon steel, Sch.40, 6"
diameter pumping manifold according to the
attached drawings. The new manifold shall
include all needed works and required items
including, flanges, fittings, couplings, reducers,
connections, SS bolts, nuts, gaskets, jack
supports, thrust blocks etc, complete all as
described in the Specifications and as shown on
the Drawings and as directed by the Engineer.
The works also include all requirements to
reconnect the new manifold piping system to the
existing distribution pipes.
Contractor Signature
14
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
Unit
Total
Item Description Unit Qty. Price
(US$)
(US$)
2.2.8 Supply and install 6'' approved stainless steel pipe
4 mm thick provided with 1/2'' feeding point for
disinfection, complete all as described in the
Specifications and as shown on the Drawings and
as directed by the Engineer. MR 1
2.4 Remove the rusty areas with sandy paper for Fuel
tank and repaint with one primer coat and at least
three coats of approval epoxy paint. The item
includes the inside cleaning of the tank according to
the instructions of the Engineer, and filling the tank
with (5000 l) approved fuel up to its full capacity. L.S. 1
Contractor Signature
15
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
Unit
Total
Item Description Unit Qty. Price
(US$)
(US$)
2.5 Dismantle, supply, and install to replace the rusty
fuel pipe 3/4" and install new black steel pipe
(3/4") with all fittings (elbows, couples, etc.) to
connect the fuel tank with the generator including
paint with one primer coat according to Engineer's
instructions. L.S. 1
3. Electrical Works
General:
The Installation of electrical combinations is
outside plastering, except if stated that the work is
installed instead of an old one.
Contractor Signature
16
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
Unit
Total
Item Description Unit Qty. Price
(US$)
(US$)
3.8 Supply and install fluorescent light fixture with its
18W lamp 220V, 60cm long, daylight, wires,
conduits, bolts & clamps with 10 hours charger. No 4
Contractor Signature
17
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
1. Civil Works
1.9 Supply and paint super lack paint and one primer
coat for doors and windows. The works include
removing the old paint and cleaning the surface. M2 21
Contractor Signature
19
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
Unit Price Total
Item Description (US$)
Unit Qty. (US$)
1.15 Supply and install galvanized steel ladder, the price
should include painting with one prime coat and
two coats of approved oil paint, all according to
Drawings, Specifications and instructions of the
Engineer. ML 4
2. Mechanical Works
2.1 WaterPumpingUnit:
Dismantle the existing vertical turbine pump
complete including the motor. Supply, install and
connect to the electrical board, multistage Vertical
Turbine Pump, Saudi National Pump, KSB,
Hamecdash, Paterson type or equivalent complete
with all associated fittings and accessories
recommended for installations by the pump
manufacturer with electrical motor US motors type
or equivalent with hollow shaft, 1450rpm, IP55,
stator winding fitted with PT100 temperature
sensors. The motor should be capable to operate
the system and should be selected according to the
manufacturer recommendation.
The unit should be comprised of vertical line shaft
driven turbine pump of cast iron bowls with rubber
bearings, bronze impellers, bronze line shaft
bearings with rubber inserts, including stainless
steel grade (ASTM A582 grade 416 stainless steel)
1 Dia. column drive shafts, and epoxy painted
steel column pipes 6 diameter. Sch. 40 (min thick
7.92 mm) with minimum total length of 72m, well
head foundation, steel discharge head 6/6 epoxy
painted, and 3 galvanized steel pipe for
measuring water level, in addition to any fittings
and components required for the satisfactory
operation of the system and all necessary works
according to specifications, drawings, and
instructions by the Engineer.
The works, installations and prices should include
for all mechanical pipe work installations,
electrical installations with cables including
builders work installations with all associated
reinforced concrete plinths specified by the
manufacturer's installation manual.
The operating point of the pump is (115) M3/hr at a
total dynamic head (TDH) of 84m at minimum
78% pump efficiency. The pump largest diameter
must not exceed 8. L.S. 1
Contractor Signature
21
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
Unit Price Total
Item Description (US$)
Unit Qty. (US$)
2.2.10 Supply and install non-buried 6'' diameter
(4.76mm) thickness Steel pipes with required jack
supports including required works. MR 2
2.4 Remove the rusty areas with sandy paper for Fuel
tank and repaint with one primer coat and at least
three coats of approval epoxy paint. The item
includes the inside cleaning of the tank and the
replacement and connection of the existing level
pipe and floats, all according to the instructions of
the Engineer, and filling the tank with (5000 l)
approved fuel up to its full capacity. L.S. 1
3. Electrical Works
General:
The Installation of electrical combinations is
outside plastering, except if stated that the work is
installed instead of an old one.
3.4 Supply and install single one way 220v in the wall
, 10A, on/off switch ( Replace old one in the Grad
room ) No. 4
3.5 Supply and install 10A ,220V out let socket in the
wall ( Replace old one in the Grad room ) No. 3
Contractor Signature
23
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
Unit Price Total
Item Description (US$)
Unit Qty. (US$)
3.9 Supply and install external mounted 12C.B
capacity electrical distribution board including
connection to earth and neutral. (DB-A)+(DB-A2 ) No. 2
Contractor Signature
24
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
2. Mechanical Works
2.1 WaterPumpingUnit:
Dismantle the existing vertical turbine pump
complete including the motor. Supply, install and
connect to the electrical board, multistage Vertical
Turbine Pump, Saudi National Pump, KSB,
Hamecdash, Paterson type or equivalent complete
with all associated fittings and accessories
recommended for installations by the pump
manufacturer with electrical motor US motors type
or equivalent with hollow shaft, 1450rpm, IP55,
stator winding fitted with PT100 temperature
sensors. The motor should be capable to operate
the system and should be selected according to the
manufacturer recommendation.
The unit should be comprised of vertical line shaft
driven turbine pump of cast iron bowls with rubber
bearings, bronze impellers, bronze line shaft
bearings with rubber inserts, including stainless
steel grade (ASTM A582 grade 416 stainless steel)
1 Dia. column drive shafts, and epoxy painted
steel column pipes 6 diameter. Sch. 40 (min thick
7.92 mm) with minimum total length of 80m, well
head foundation, steel discharge head 6/6 epoxy
painted, and 3 galvanized steel pipe for
measuring water level, in addition to any fittings
and components required for the satisfactory
operation of the system and all necessary works
according to specifications, drawings, and
instructions by the Engineer.
The works, installations and prices should include
for all mechanical pipe work installations,
electrical installations with cables including
builders work installations with all associated
reinforced concrete plinths specified by the
manufacturer's installation manual.
The operating point of the pump is (115) M3/hr at a
total dynamic head (TDH) of 81m at minimum
78% pump efficiency. The pump largest diameter
must not exceed 8. L.S. 1
Contractor Signature
25
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
Item Description Unit Price Total
Unit Qty. (US$) (US$)
Contractor Signature
26
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
Item Description Unit Price Total
Unit Qty. (US$) (US$)
2.2.8 Supply and install above ground All Flanged Steel
Tee 6''6'' 6'', complete with all required works as
described in the Specifications and as shown on the
Drawings and as directed by the Engineer. No. 1
2.4 Remove the rusty areas with sandy paper for Fuel
tank and repaint with one primer coat and at least
three coats of approval epoxy paint. The item
includes the inside cleaning of the tank according
to the instructions of the Engineer, and filling the
tank with (5000 l) approved fuel up to its full
capacity. L.S. 1
Contractor Signature
27
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
Item Description Unit Price Total
Unit Qty. (US$) (US$)
2.6 Supply, install, test and commission PVC roof
water tanks of 500 litter capacity complete with
float valve, connection pipes and all necessary
valves, vents, fittings, cover, overflow, drain to the
nearest drain point, painting with white policed,
and all accessories needed to complete the work as
per specifications, drawings and the engineer
instructions. No. 1
3. Electrical Works
General:
The Installation of electrical combinations is
outside plastering, except if stated that the work is
installed instead of an old one.
Contractor Signature
28
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
Unit
Total
Item Description Price
Unit Qty. (US$)
(US$)
E. UM AL- NASER WELL (C210)
1. Civil Works
2. Mechanical Works
2.1 WaterPumpingUnit:
Dismantle the existing vertical turbine pump
complete including the motor. Supply, install and
connect to the electrical board, multistage Vertical
Turbine Pump, Saudi National Pump, KSB,
Hamecdash, Paterson type or equivalent complete
with all associated fittings and accessories
recommended for installations by the pump
manufacturer with electrical motor US motors type
or equivalent with hollow shaft, 1450rpm, IP55,
stator winding fitted with PT100 temperature
sensors. The motor should be capable to operate the
system and should be selected according to the
manufacturer recommendation.
The unit should be comprised of vertical line shaft
driven turbine pump of cast iron bowls with rubber
bearings, bronze impellers, bronze line shaft
bearings with rubber inserts, including stainless
steel grade (ASTM A582 grade 416 stainless steel)
1 Dia. column drive shafts, and epoxy painted
steel column pipes 6 diameter. Sch. 40 (min thick
7.92 mm) with minimum total length of 84m, well
Contractor Signature
29
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
Unit
Total
Item Description Price
Unit Qty. (US$)
(US$)
head foundation, steel discharge head 6/6 epoxy
painted, and 3 galvanized steel pipe for
measuring water level, in addition to any fittings
and components required for the satisfactory
operation of the system and all necessary works
according to specifications, drawings, and
instructions by the Engineer.
The works, installations and prices should include
for all mechanical pipe work installations, electrical
installations with cables including builders work
installations with all associated reinforced concrete
plinths specified by the manufacturer's installation
manual.
The operating point of the pump is (115) M3/hr at a
total dynamic head (TDH) of 87m at minimum
78.7% pump efficiency. The pump largest diameter
must not exceed 8. L.S. 1
2.2 PUMPING MANIFOLD:
General:
The new manifold shall include all needed works
and required items to reconnect the new manifold
piping system to the existing distribution pipes
including pipes, valves, meters, flanges, fittings,
couplings, reducers, connections, SS bolts, nuts,
gaskets, jack supports, thrust blocks etc,
complete all as described in the Specifications
and as shown on the Drawings and as directed by
the Engineer.
Contractor Signature
30
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
Unit
Total
Item Description Price
Unit Qty. (US$)
(US$)
2.2.6 Supply and install above ground 6'' 45o Steel
Elbow, complete all as shown on the Drawings and
as directed by the Engineer. No. 1
3. Electrical Works
General:
The Installation of electrical combinations is
outside plastering.
Contractor Signature
31
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
Unit
Total
Item Description Price
Unit Qty. (US$)
(US$)
1.5mm2 , 3/4" plastic pipes, clamps and all
accessories to complete the job
Contractor Signature
32
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
Unit
Total
Item Description Price
Unit Qty. (US$)
(US$)
F. MISCELLANEOUS WORKS
The items below include the supplying and testing
and all required materials, workmanship etc.
All the following items should be completed
according to drawings, specifications and
Engineers instructions.
The following items shall be used wherever
needed.
Contractor Signature
33
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
Unit
Total
Item Description Price
Unit Qty. (US$)
(US$)
9. Supply and install 120 cm internal diameter precast
circular reinforced concrete water manholes,
complete with B300 cast in place reinforced concrete
base, cast iron cover (25ton Capacity), Frame, rings,
the concrete which is to be used around the ring is
B350 for at least 30cm width and depth, Basalt layer
of 2 cm thick above the concrete and around the
cover to fix the ring should be supplied and installed,
cast iron steps @ 30cm maximum, excavation in any
type of soil to any depth , backfilling with clean dune
sand and compaction 98% MDD up to the design
leveling of the roads, drainage opening with
aggregate bed, two external hot bitumen coating
(75/25). The price includes supply and installs the
required 8 Gate valve 10 bar working pressure
Hakohav type or equivalent, including all needed
fittings and supports to complete as per drawings,
specification and Engineer instruction. L.S 1
10. Ditto, but 1.0m internal Dia. With 6 Gate valve. L.S 1
Contractor Signature
35
ITB 2011-024
Lot # 3: Rehabilitation of Bait Hanoun Water wells
SUMMARY OF BILL OF QUANTITIES
F. MISCELLANEOUS WORKS
Total price
Discount %
Price After Discount
We the undersigned representative hereby certify our pre-tendering site visit with full
understanading and commitments towards the excutions of all works and installations
in accordance with all relevant applicable standards (ISO,BS,ASTM ),drawings ,
specifications and engineers instructions.
We have carefully checked and examined all bid documents and we are fully aware of
all descripances that may be occurred during the construction period which are
covered by the bid prices.
Signature : ___________________________________________________
Stamp: ___________________________________________________
Date : ___________________________________________________
Contractor Signature
36