SECTION D DIAGRAMS
12-00
SWEDISH
SPREADER SERVICE MANUAL BUILD INDEX
SYSTEMS
ELMHULTS KONSTRUKTIONS AB BUILD INDEX NO. 1-542
SECTION A
USER INSTRUCTION
12-00
SWEDISH
SPREADER
SYSTEMS
ELMHULTS KONSTRUKTIONS AB
USER INSTRUCTIONS PAGE NO 100-043-1
OPERATOR INSTRUCTIONS
Initial check.
Each work shift should be started by making a visual check of the unit ( this must be
part of the daily routine. ) Possible damage will in this way be discovered at an early
stage thus enabeling repairs to be carried out at much lower cost.
NEVER USE THE UNIT UNLESS ALL SAFETY DEVICES FUNCTION
CORRECTLY !!!
CONTAINER HANDLING
When the required length has been reached, lift the spreader high enough to ensure
that it will not hit stacked containers and other obstacles.
2. Picking up a container.
If necessary raise the spreader in order to have plenty of space between it and the
container. Always attempt to position the spreader centrally over the container.
The final adjustments for lining up the twist locks with the corner castings of the
container can now be made.
Position the spreader as accurately as possible over the container to be lifted. Lower
the spreader until it is close enough to the container.
01-03(06-97)
SWEDISH
SPREADER
SYSTEMS
ELMHULTS KONSTRUKTIONS AB
USER INSTRUCTIONS PAGE NO 100-043-1
The spreader can now be lowered into the corner castings and the weight of the
spreader allowed to rest unsupported on the container. When the twist locks are
correctly positioned in the corner castings it is termed as the spreader being correctly
SEATED, and this will be indicated by the SEATED LIGHT being switched on.
The indicator panel will now have two lamps illuminated, the SEATED and the NOT
LOCKED lamps. As soon as this happens the twist locks can be activated to the
locked position. The LOCKED light will be switched on and the NOT LOCKED light
will switch off leaving the SEATED and LOCKED lights on.
As the spreader is lifted and the twistlocks begin to lift the container, the SEATED
light will switch off. When this happens the twistlock activation and the spreader exten-
sion circuits are disabled ensuring that they cannot be inadvertantly activated during
transport of a container
CHECK THAT THE LOCKED LIGHT HAS BEEN SWITCHED ON and then lift
the container to the required height for loading and / or travelling. The container is now
ready to be transported to a new location.
3. Depositing a container.
When approaching the new location for the container (this could be a chassis or a
stack etc.) lower the container to the required height and adjust the position of the
corner castings so that they are accurately situated above the corner locks of the
chassis. Lower the container ensuring that its corner castings locate on the corner
locks. Continue to lower the spreader until it rests unsupported on the container. This
will activate the SEATED light and the twist locks may now be activated to the NOT
LOCKED position. In the not locked position both the SEATED and the NOT
LOCKED lights will be illuminated. The spreader can now be lifted free of the
container.
WARNING !!! A heavy container and the weight of a spreader will do serious
damage to a trailer or chassis if not handled with care.
NEVER PULL THE CONTAINER BY USING THE ROPES OF THE CRANE !!!
4. General advice
- Always retract the spreader to the 20ft position when stowing.
- Read all instruction books carefully and be sure that you understand them.
01-03(06-97)
SWEDISH
SPREADER SERVICE MANUAL BUILD INDEX
SYSTEMS
ELMHULTS KONSTRUKTIONS AB BUILD INDEX NO. 1-542
SECTION B
SERVICE MANUAL
12-00
SWEDISH
SPREADER
SYSTEMS MAINTENANCE INSTRUCTIONS PAGE NO 110-073-1
ELMHULTS KONSTRUKTIONS AB
LUBRICATION CHART
3, 4
3, 4
2 2
1 5
LUBRICANT :
2 2
MULTI-PURPOSE GREASE WITH
2-4% MOLYBDENUM DISULFIDE ADDITIVE
POSITION 1.
POSITION 2.
POSITION 3.
EXTENTION CYLINDER SUPPORT WEAR PADS
AND TRACKS.
POSITION 4
STOP CYLINDERS.
NO. OF GREASE POINTS 2.
POSITION 6 A
HYDRAULIC POWER PACK.
POINTS.
"A" 2 OFF HIGH PRESSURE FILTERS (CHANGE FILTER
ELEMENTS) C
"B" 2 OFF RETURN FILTERS (CHANGE FILTER
ELEMENTS) B
"C" HYDRAULIC TANK (CHECK OIL LEVEL DAILY.)
CHANGE THE HYDRAULIC OIL EVERY 1000 HOURS
HIGH PRESSURE FILTER ELEMENT USE ELME PART NO. 762 201 A
RETURN FILTER ELEMENT USE ELME PART NO. 762 164
02-98
SWEDISH
SPREADER
SYSTEMS MAINTENANCE INSTRUCTIONS PAGE NO 110-017-1
ELMHULTS KONSTRUKTIONS AB
1. - The nylon wear pads should be inspected for wear at the same time
as their tracks are lubricated. The pads should be replaced when their
thickness is reduced to minimum 18 mm.
Replacing the wear pads can be done with ordinary hand tools and
without removing the beams.
Minimum thickness 18 mm
The drawing above shows where the heads of the twist locks
wear. When the worn part exceeds the area indicated by cross
hatching the twist locks should be replaced.
05-03(11-92)
SWEDISH
SPREADER
SYSTEMS MAINTENANCE INSTRUCTIONS PAGE NO 110-017-2
ELMHULTS KONSTRUKTIONS AB
3. - The extension cylinder support has wear pads under it. These should also
be inspected on a regular basis and replaced when their thickness is
reduced to minimum 18 mm. See item 1.
5 - The side shift wear pads should be inspected for wear at the same time
as lubrication is carried out. The wear pads should be replaced when their
thickness is reduced to minimum 18 mm. See item 1.
05-03(11-92)
SWEDISH
SPREADER
SYSTEMS MAINTENANCE INSTRUCTIONS PAGE NO 110-068-1
ELMHULTS KONSTRUKTIONS AB
12
8
11
10
1 4
3
7
2 Loosen one of the adjuster bolts at the twistlock cylinder, enough to give some
play.
3 Loosen and remove the M8 x 80 bolts (item 2) in the top of both twistlocks
in the same end beam.
5 The tie-rod (item 6) including both cranks (item 4) can now be removed from the
end beam.
6 The key (item 7) that locates the crank (item 4) to the twistlock (item 5) is held in
place on the twistlock by a roll pin so that it will remain in place on the twistlock
after the crank is removed.
By lightly knocking the key away from the twistlock it can be removed.
08-00(09-98,
05-98,08-97)
SWEDISH
SPREADER
SYSTEMS MAINTENANCE INSTRUCTIONS PAGE NO 110-068-2
ELMHULTS KONSTRUKTIONS AB
7 Support the twistlock (item 5) from below so that it does not drop out.
Using a screwdriver prise the collets (item 8) out of the recess in the twistlock (item 5). It is
now possible to lower the twistlock out of the end beam. The sleeve (item 9) and lower
bearing set (item 10) will in most cases accompany the twist lock as it is removed, this is
quite normal.
8 After removal of all twistlock parts remove all grease and dirt from the parts and also from
the corner of the end beam. Steam clean or clean with some form of solvent.
9 Check the twistlock (item 5) for wear at the head and also for wear at the bushing
surfaces. Inspect the lower (item 10) and upper (item 11) bearing sets for wear and
damage, if badly worn or damaged they should be replaced. The collets (item 8) and the
crank (item 4) should be inspected for possible wear or damage and replaced if necessary.
It should be noted that the state of the collets (item 8) and the recess in the twist
lock (item 5) is very important as these parts are carrying the load when a container
is lifted.
10 Replacing the twistlock is the revers order of removal, however the best way to start
assembly is to assemble the sleeve (item 9) including bushes, onto the twistlock (item
5) and then grease the the lower bearing set (item 10) and place in position on top of the
sleeve. Fit the four centering springs in the sides of the sleeve.
11 Grease the upper bearing set (item 11) and place in position on the top surface of the
corner plate (in the end beam) with the convex half uppermost (threaded holes up)
12 Lift the twistlock assy. as assembled in point 10 and position up through the corner plate in
the end beam, ensuring that the upper bearing set (item 11) is positioned correctly around
the twistlock. Support the assembly with a jack or other means and then go to the next
point.
14 Fit the key (item 7) incl. roll pin to the keyway of the twistlock (item 5)
15 In order to fit the tie-rod (item 6) it is necessary to mount both cranks (item 4) to the tie-rod
before placing it in the end beam. Fit the ball joints, O rings, and plastic washers to the tie-
rod ends and then fit the fork of the crank (item 4) over the tie-rod end. Ensure that the
countersunk ends of the securing holes in the crank are uppermost. Secure the crank to
the tie-rod end by fitting the pin (item 12) and then the ring pin and allen screw.
16 In order to simplify assembly of the crank to the twistlock it is advisable to fit two alignment
pins to the assy. The pins can be made from two M8 x 75 bolts or allen screws with the
heads removed and slightly chamfered.
These pins should be screwed into the top plate of the upper bearing (item 11) diagonally
so that each pin guides one half of the collets (item 8).
08-00(09-98,
05-98,08-97)
SWEDISH
SPREADER
SYSTEMS MAINTENANCE INSTRUCTIONS PAGE NO 110-068-3
ELMHULTS KONSTRUKTIONS AB
17 Insert the tie-rod (item 6) into the end beam and the fit the cranks (item 4) onto the
alignment pins and ensure that the key and keyway line up. Fit two of the allen securing
(item 2) in the remaining two holes and screw in and tighten lightly. Remove the alignment
pins and fit the other two securing screws. The securing screws can now be tightened to
approx. 25 Nm.
18 Activate the twistlocks to the NOT LOCKED position and then adjust the twistlock cylinder
adjuster bolts so that the twistlocks are positioned accuratly in the NOT LOCKED posi
tion. Ensure that there is Zero play between the adjuster bolts and the twistlock cylinder
rod ends.
In order to test the operation it is necessary to land the spreader on a container so that the
seated pins are activated.
08-00(09-98,
05-98,08-97)
SWEDISH
PAGE NO
SPREADER
SYSTEMS MAINTENANCE INSTRUCTIONS 110-081
ELMHULTS KONSTRUKTIONS AB
C D D B
A
A
1
B Fig 1 C
A Extension beams
B Extension cylinder
C Inspection hole
D Hose / Cable chain
2 - Before removing the securing pin pos.1 of the extension cylinder it must be
supported by a small hydraulic jack or likewise so that the cylinder pos. B
does not fall down.
Remove the pin from the rear of the cylinder fig1 pos 1 (opposite end to the
piston rod) and at the same time also remove the hose and electrical
connections at the rear of the extension cylinder pos. B. The securing bracket
that secures the cable chain to the track in the bottom of the extension beam
should also be disconnected.
3 - By using a crane or fork lift truck pull the end beam pos. A out approx. 50cm so
that it is just possible to get into the inspection hole pos.C in the top of the
beam.
4 - Remove the pin from the piston rod end of the extension cylinder.
5 - The extension cylinder pos. B can now be lifted out of the spreader by sliding it
horisontally with the help of suitable lifting equipment, (by "suitable lifting
equipment" is meant that the crane or truck must be capable of lifting 150kg .)
until the slider pads slide out of the rail by which the foot of the cylinder is
guided.
04-98
SWEDISH
SPREADER SERVICE MANUAL BUILD INDEX
SYSTEMS
ELMHULTS KONSTRUKTIONS AB BUILD INDEX NO. 1-542
SECTION C
PARTS MANUAL
12-00
SWEDISH
SPREADER MAIN FRAME
SYSTEMS PAGE NO 10-623-1
ELMHULTS KONSTRUKTIONS AB FOR SPREADER MODEL 8100
4,5,6 1
10
10
7,8,9 4,5,6
12
11
2
3
6 11
5
12 4,5,6
4
10
10 1 7,8,9
11-00
SWEDISH
SPREADER MAIN FRAME
SYSTEMS
FOR SPREADER MODEL 8100 PAGE NO 10-623-2
ELMHULTS KONSTRUKTIONS AB
S) 1 2 Wear pads
T) 2 1 Power pack
U) 3 6 Length indication arrangement
4 741 178 4 Cover
5 761 764 12 Bolt M6x16
760 585 12 Lockwasher M6 Nordlock
6 741 179 4 Strip
V) 7 2 Pendular twistlock assy.
X) 8 4 Pendular twistlock arr.
Y) 9 752 651 2 Hydraulic twistlock cylinder assy.
10 756 821 4 Bumper
791 055 4 Bolt kit
11 755 175 4 Pin
Z) 12 2 Hydraulic extension cylinder assy.
749 760 2 Buffer
760 922 2 Nut
742 262 2 Washer
749 793 8 Washer
11-00
SWEDISH
SPREADER WEAR PADS
SYSTEMS PAGE NO 10-224
FOR SPREADERS MODEL 815/817/818
ELMHULTS KONSTRUKTIONS AB
9 10 11
21
3
4
5
1 5 4
6
7
4
5
02-99(08-98,
04-98,10-97,12-95)
SWEDISH
SPREADER LENGTH INDICATOR ARR. IN MAIN FRAME - EXT. BEAM
SYSTEMS PAGE NO 10-323
ELMHULTS KONSTRUKTIONS AB
10
3 11
4 12
5
6 13
7
14
8
9 15
1 1 Extension beam
X) 2 751 041 1 Wear pad
X) 3 746 236 1 Bracket
X) 4 760 946 4 Bolt M6S M16x65
X) 5 760 586 4 Washer M16 Nordlock
X) 6 760 919 2 Nut M8 Locking
X) 7 762 814 2 Screw
X,S) 8 751 042 1 Plate
X,Y) 751 043 1 Plate
X) 9 760 473 4 Spring
10 1 Main frame
X) 11 750 903 1 Bracket
X) 12 762 527 1 Proximity switch
X) 13 762 539 1 Cable assy.
X) 14 760 974 2 Bolt M6S M12x30
X) 15 760 917 2 Nut M12 Locking
X) The quantities are only for one unit (as shown in above drawing)
S) Used for spreaders with stops not only in 20', 40' position
Y) Used for spreaders without stops or stops in 20', 40' position
03-03(08-00,01-99,01-98,06-97)
SWEDISH
SPREADER
SYSTEMS PENDULAR TWISTLOCK ASSY. PAGE NO 50-181-1
ELMHULTS KONSTRUKTIONS AB
5
36
28 5 37
36 29,30
31 7
37
33
34 35 29,30
1
32
7 6
26 4
6
8
2
15
16 2 3
16
9
17
17
18 11 13 12
19
20
21 9
22 23,24 25
10
26 36
37
14,27 7 28 5 29,30
09-02(02-01,02-00,10-99,09-99,04-99)
SWEDISH
SPREADER
SYSTEMS PENDULAR TWISTLOCK ASSY. PAGE NO 50-181-2
ELMHULTS KONSTRUKTIONS AB
09-02(02-01,02-00,10-99,09-99,04-99)
SWEDISH
SPREADER PENDULAR TWIST LOCK
SYSTEMS PAGE NO 50-188-1
FOR CRANE SPREADERS
ELMHULTS KONSTRUKTIONS AB
1 4,5
12
13
14
7,8
9,10
11
09-02(11-99)
SWEDISH
SPREADER PENDULAR TWIST LOCK
SYSTEMS PAGE NO 50-188-2
FOR CRANE SPREADERS
ELMHULTS KONSTRUKTIONS AB
W) 1 1 Twistlock cyl.
2 740 866 2 Adjuster
760 586 2 Washer M16 Nordlock
3 760 944 2 Nut M16
4 760 969 4 Bolt M6S M10x25
5 760 556 4 Lockwasher M10 Nordlock
6 752 619 1 Sensor bracket
7 760 985 2 Bolt M6S M10x50
8 760 991 2 Bolt M6S M10x80
9 761 154 4 Washer
10 760 927 4 Nut M10 Locking
X) 11 2 Twist lock assy.
12 760 919 2 Nut M8 Locking
761 154 2 Washer
13 762 527 2 Proximity switch M30
14 761 751 2 Bolt M6S M8x60
761 154 2 Washer
09-02(11-99)
SWEDISH
SPREADER
SYSTEMS TWIST LOCK CYLINDER ASSY. PAGE NO 60-218
ELMHULTS KONSTRUKTIONS AB
2 3 4 5 6 13 5 4
1 7 8 9 10 11 12 7
2
3
02-05(08-98,01-98,02-97)
SWEDISH
SPREADER
SYSTEMS EXTENSION CYLINDER ASSY. PAGE NO 60-329-1
ELMHULTS KONSTRUKTIONS AB
23 27
26
16 24
5 4
17 25
25
6 24
26
8 18
27
4
7
9
30
4
10
28
19
11
20
12
21
13
22 29
4
14
15
31 41 42
37
38
32 39
33 40
34
35
36
12-00
SWEDISH
SPREADER
SYSTEMS EXTENSION CYLINDER ASSY. PAGE NO 60-329-2
ELMHULTS KONSTRUKTIONS AB
12-00
SWEDISH
SPREADER
SYSTEMS POWER PACK ASSEMBLY FOR SPREADERS MODEL 8100/8200 PAGE NO 70-329-1
ELMHULTS KONSTRUKTIONS AB
1 2 20 3 4 5 1
21
25
23 24 22
7
15
8
16
26
17
9
27 10
11
12
13
14
1 2 18 28 3 4 5 1
19
02-02(01-02,06-01,03-00,
03-99,02-99,06-97,04-97)
SWEDISH
SPREADER
SYSTEMS POWER PACK ASSEMBLY FOR SPREADERS MODEL 8100/8200 PAGE NO 70-329-2
ELMHULTS KONSTRUKTIONS AB
02-02(01-02,06-01,03-00,
03-99,02-99,06-97,04-97)
SWEDISH
SPREADER
SYSTEMS INDICATOR LIGHT ASSY PAGE NO 80-194
ELMHULTS KONSTRUKTIONS AB
3 4 9 10
11
01-00(12-99,02-99)
SWEDISH
SPREADER
SYSTEMS
ELMHULTS KONSTRUKTIONS AB
INSTRUCTION PAGE NO 80-183
INSTRUCTION ON HOW TO USE THE " BILL OF MATERIAL " PAGES IN THE PARTS
MANUAL
1 THE "BILL OF MATERIAL" HAS A LIST NO. IN THE SQUARE IN THE TOP RH CORNER
WHICH IS THE SAME AS THE WIRING DIAGRAM TO WHICH IT RELATES.
EX. WIRING DIGRAM NO. 752 713 HAS A "BILL OF MATERIAL" NO 752 713.
THE WIRING DIAGRAM SHOWS A SWITCH FOR HIGH BOOM ANGLE AT THE RH SIDE
OF THE DIAGRAM. ADJACENT TO THE SWITCH IS THE CODE NO. S13. BY GOING TO
THE "BILL OF MATERIAL" AND LOCATING S13. IT CAN BE SEEN THAT THE SWITCH
HAS ELME P/N 761 523
THE ABOVE PROCEDURE CAN BE USED WITH ALL CODE NO.S TO BE FOUND
ON ANY SCHEMATIC OR WIRING DIAGRAM.
04-97
SWEDISH
SPREADER ELECTRIC SYSTEM LIST NO
SYSTEMS
ELMHULTS KONSTRUKTIONS AB
FOR SPREADER MODEL 8100 771 382-1
12-00
SWEDISH
SPREADER ELECTRIC SYSTEM LIST NO
SYSTEMS
ELMHULTS KONSTRUKTIONS AB
FOR SPREADER MODEL 8100 771 382-2
S1-S8,S13-S14,
S19-S20 Proximity switch 762 527 12 off
12-00
SWEDISH
LIST NO
SPREADER
SYSTEMS Parker fittings O-lok for ELME spreader FITTINGS
ELMHULTS KONSTRUKTIONS AB
ORFS
THREAD DIM THREAD DIM
ELME NR PARKER NAME STRAIGHT
(INCHES) (MM)
THREAD
T5,T6 T5,T6 T
Male connector BSPP
762 625 4F42 EDMLOS 1/8 9,728 9/16-18
762 550 4-4F42 EDMLOS 1/4 13,157 9/16-18
762 592 4-6F42 EDMLOS 3/8 16,662 9/16-18
763 005 4-8F42 EDMLOS 1/2 20,955 9/16-18
762 585 8-4F42 EDMLOS 1/4 13,157 13/16-16
762 482 8F42 EDMLOS 3/8 16,662 13/16-16
762 621 8-8F42 EDMLOS 1/2 20,955 13/16-16
762 722 8-12F42 EDMLOS 3/4 26,441 13/16-16
762 838 10F42 EDMLOS 1/2 20,955 1-14
762 619 10-12F42 EDMLOS 3/4 26,441 1-14
762 505 12F42 EDMLOS 3/4 26,441 1.3/16-12
762 483 12-8F42 EDMLOS 1/2 20,955 1.3/16-12
Male connector UNF
763 090 8F5 OMLOS 3/4-16 13/16-16
762 623 8-6F5 oMLOS 9/16-18 13/16-16
762 618 8-12F5 OMLOS 1.1/16-12 13/16-16
763 119 10-12F5 OMLOS 1,1/16-12 1-14
762 617 12F5 OMLOS 1.1/16-12 1.3/16-12
Male connector Metric
762 566 6M14F82 EDMLOS M 14X1.5 11/16-16
Swivel male connector BSPP
762 622 8F642 EDMLS 3/8 16,662 13/16-16
763 036 8-4F642 EDMLS 1/4 13,157 13/16-16
762 620 10F642 EDMLS 1/2 20,955 1-14
Male elbow BSPP 45o
762 639 4-4V4 OMLOS 1/4 13,157 9/16-18
762 509 8V4 OMLOS 3/8 16,662 13/16-16
762 638 10-12V4 OMLOS 3/4 26,441 1-14
762 637 12V4 OMLOS 3/4 26,441 1.3/16-12
05-02(04-99,12-98)
SWEDISH
LIST NO
SPREADER
SYSTEMS Parker fittings O-lok for ELME spreader FITTINGS
ELMHULTS KONSTRUKTIONS AB
ORFS
THREAD DIM THREAD DIM
ELME NR PARKER NAME STRAIGHT
(INCHES) (MM)
THREAD
T1,T5,T6 T1,T5,T6 T
Male branch tee BSPP
05-02(04-99,12-98)
SWEDISH
SPREADER
HOW TO KNOW WHICH LIST NO
SYSTEMS HYDRAULIC HOSE INCL. FITTINGS YOU WILL ORDER HYDR HOSE
ELMHULTS KONSTRUKTIONS AB
6 the first digit specifies a hydr. steel braid hose with Parker fittings
3 the second digit specifies hose dimension (hose 3/8'')
2 the third digit specifies fittings (Triple-lok JIC 37)
5 the fourth digit specifies the hoses cut length in 100 cm
5 the fifth digit specifies the hoses cut length in 10 cm
0 the sixth digit specifies the hoses cut length in cm
= Hydraulic hose, 3/8", fitting straight/90, 550cm
FITTINGS ONLY
TRIPLE-LOK JIC 37 O-LOK ORFS
Parker no. ELMEno. Description Parker no. ELME no. Description
Pressure fittings - straight Pressure fittings-straight
16846-4-4 762 017 straight - 1/4" hose 1JC46-4-4 762 608 straight - 1/4'' hose
16846-5-4 762 021 straight - 1/4'' hose 1JC46-8-6 762 603 straight - 3/8'' hose
16846-8-6 762 018 straight - 3/8" hose 1JC46-8-8 762 604 straight - 1/2'' hose
16846-8-8 762 019 straight - 1/2" hose 1JC46-12-8 762 725 straight - 1/2'' hose
16846-10-10 762 020 straight - 5/8" hose 1JC46-10-10 762 600 straight - 5/8'' hose
10646-12-12 762 022 straight - 3/4" hose 1JC46-12-12 762 599 straight - 3/4' hose
Pressure fittings - 45 degr. Pressure fittings - 45 degr.
13V46-4-4 762 023 45degr - 1/4" hose 1J746-4-4 762 610 45 degr. - 1/4'' hose
13V46-8-6 762 024 45degr - 3/8" hose 1J746-8-6 762 607 45 degr. - 3/8'' hose
13V46-8-8 762 025 45degr - 1/2" hose 1J746-8-8 763 100 45 degr. - 1/2'' hose
13V46-10-10 762 026 45degr - 5/8" hose
13746-12-12 762 027 45degr - 3/4" hose
Pressure fittings - 90 degr. Pressure fittings - 90 degr. short
13W46-4-4 762 028 90degr - 1/4" hose 1J946-4-4 762 609 90 degr. - 1/4'' hose
13W46-5-4 762 029 90degr - 1/4" hose 1J946-6-6 762 612 90 degr. - 3/8'' hose
13W46-8-6 762 030 90degr - 3/8" hose 1J946-8-6 762 606 90 degr. - 3/8'' hose
13W46-8-8 762 031 90degr - 1/2" hose 1J946-8-8 762 602 90 degr. - 1/2'' hose
13W46-10-10 762 032 90degr - 5/8" hose 1J946-10-10 762 601 90 degr. - 5/8'' hose
13946-12-12 762 033 90degr - 3/4" hose 1J946-12-12 762 598 90 degr. - 3/4'' hose
Pressure fittings - ext. Pressure fittings - 90 degr. long
10346-5-4 762 070 ext. straight - 1/4" 1J146-8-6 762 611 90 degr. - 3/8'' hose
10346-8-8 762 335 ext. straight - 1/2" 1J146-8-8 762 605 90 degr. - 1/2'' hose
09-03(10-02,05-02,02-02,03-99,12-98)
SWEDISH
SPREADER SERVICE MANUAL BUILD INDEX
SYSTEMS
ELMHULTS KONSTRUKTIONS AB BUILD INDEX NO. 1-542
SECTION D
DIAGRAMS
12-00