Anda di halaman 1dari 169

eRAN

Idle Mode Management Feature


Parameter Description

Issue 01
Date 2017-03-08

HUAWEI TECHNOLOGIES CO., LTD.


Copyright Huawei Technologies Co., Ltd. 2017. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior written
consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.

Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the
customer. All or part of the products, services and features described in this document may not be within the
purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,
and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.

The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.

Huawei Technologies Co., Ltd.


Address: Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China

Website: http://www.huawei.com
Email: support@huawei.com

Issue 01 (2017-03-08) Huawei Proprietary and Confidential i


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description Contents

Contents

1 About This Document.................................................................................................................. 1


1.1 Scope.............................................................................................................................................................................. 1
1.2 Intended Audience.......................................................................................................................................................... 1
1.3 Change History............................................................................................................................................................... 2
1.4 Differences Between eNodeB Types.............................................................................................................................. 3

2 Overview......................................................................................................................................... 4
2.1 Introduction.................................................................................................................................................................... 4
2.2 Benefits........................................................................................................................................................................... 4
2.3 Relate Concepts.............................................................................................................................................................. 4
2.3.1 PLMN.......................................................................................................................................................................... 4
2.3.2 Access Classes............................................................................................................................................................. 5
2.3.3 Service Types...............................................................................................................................................................5

3 Technical Description...................................................................................................................7
3.1 PLMN Selection............................................................................................................................................................. 8
3.1.1 PLMN Selection in Automatic Mode.......................................................................................................................... 9
3.1.2 PLMN Selection in Manual Mode...............................................................................................................................9
3.1.3 Roaming.......................................................................................................................................................................9
3.2 Cell Selection and Reselection..................................................................................................................................... 10
3.2.1 Cell Search.................................................................................................................................................................10
3.2.2 Cell Selection.............................................................................................................................................................11
3.2.3 Neighboring Cell Priority Handling.......................................................................................................................... 13
3.2.4 Blacklisted Cell Identifying.......................................................................................................................................16
3.2.5 Neighboring Cell Measurement for Cell Reselection................................................................................................16
3.2.6 Intra-Frequency or Equal-Priority Inter-Frequency Cell Reselection....................................................................... 19
3.2.7 Different-Priority Inter-Frequency or Inter-RAT Cell Reselection........................................................................... 21
3.2.8 Speed-based Cell Reselection....................................................................................................................................25
3.3 Tracking Area Registration...........................................................................................................................................30
3.3.1 Tracking Area Update................................................................................................................................................31
3.3.2 Attach/Detach............................................................................................................................................................ 31
3.4 Cell Reservation and Access Control........................................................................................................................... 31
3.4.1 Cell Reservation and Barring.................................................................................................................................... 31
3.4.2 Access Control...........................................................................................................................................................32

Issue 01 (2017-03-08) Huawei Proprietary and Confidential ii


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description Contents

3.5 System Information Broadcast..................................................................................................................................... 33


3.5.1 System Information Block Contents..........................................................................................................................34
3.5.2 System Information Scheduling Periods................................................................................................................... 35
3.5.3 System Information Update.......................................................................................................................................35
3.6 Paging........................................................................................................................................................................... 37
3.6.1 Triggering of Paging..................................................................................................................................................37
3.6.2 Paging Mechanism over the Uu Interface................................................................................................................. 37
3.6.3 Paging Handling Procedure....................................................................................................................................... 39
3.6.4 Scheduling of Paging Messages................................................................................................................................ 40

4 Related Features...........................................................................................................................42
4.1 LBFD-002009 Broadcast of system information......................................................................................................... 42
4.2 LBFD-002011 Paging...................................................................................................................................................42
4.3 LBFD-00201803 Cell Selection and Re-selection....................................................................................................... 42

5 Network Impact........................................................................................................................... 44
5.1 LBFD-002009 Broadcast of system information......................................................................................................... 44
5.2 LBFD-002011 Paging...................................................................................................................................................44
5.3 LBFD-00201803 Cell Selection and Re-selection....................................................................................................... 45

6 Engineering Guidelines............................................................................................................. 46
6.1 When to Use................................................................................................................................................................. 46
6.2 Deployment.................................................................................................................................................................. 46
6.2.1 Requirements............................................................................................................................................................. 46
6.2.2 Data Preparation and Feature Activation...................................................................................................................47
6.2.2.1 Data Preparation..................................................................................................................................................... 47
6.2.2.2 Using the CME....................................................................................................................................................... 56
6.2.2.3 Using MML Commands......................................................................................................................................... 56
6.2.3 Activation Observation..............................................................................................................................................60
6.2.4 Reconfiguration......................................................................................................................................................... 62
6.2.5 Deactivation...............................................................................................................................................................62
6.2.5.1 Using the CME....................................................................................................................................................... 62
6.2.5.2 Using MML Commands......................................................................................................................................... 62
6.3 Performance Monitoring...............................................................................................................................................65
6.4 Parameter Optimization................................................................................................................................................ 66
6.5 Possible Issues.............................................................................................................................................................. 78

7 Parameters..................................................................................................................................... 79
8 Counters...................................................................................................................................... 161
9 Glossary....................................................................................................................................... 164
10 Reference Documents............................................................................................................. 165

Issue 01 (2017-03-08) Huawei Proprietary and Confidential iii


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 1 About This Document

1 About This Document

1.1 Scope
This document describes idle mode management, including its technical principles, related
features, network impact, and engineering guidelines. This document covers the following
features:

l LBFD-002009 Broadcast of system information


l LBFD-002011 Paging
l LBFD-00201803 Cell Selection and Re-selection

Any parameters, alarms, counters, or managed objects (MOs) described herein apply only to
the corresponding software release. For future software releases, refer to the corresponding
updated product documentation.

This document applies only to LTE (FDD). Any "LTE" in this document refers to LTE (FDD),
and "eNodeB" refers to LTE (FDD) eNodeB.

This document applies to the following types of eNodeBs.

eNodeB Type Model

Macro 3900 series eNodeB

Micro BTS3202E
BTS3203E
BTS3911E
BTS3912E

LampSite DBS3900 LampSite

1.2 Intended Audience


This document is intended for personnel who:

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 1


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 1 About This Document

l Need to understand the features described herein


l Work with Huawei products

1.3 Change History


This section provides information about the changes in different document versions. There are
two types of changes:

l Feature change
Changes in features and parameters of a specified version as well as the affected entities
l Editorial change
Changes in wording or addition of information and any related parameters affected by
editorial changes. Editorial change does not specify the affected entities.

eRAN12.1 01 (2017-03-08)
This issue includes the following changes.

Change Change Description Parameter Change Affected


Type Entity

Feature None None N/A


change

Editorial Optimized descriptions in 2.1 None -


change Introduction, 3.1 PLMN Selection,
and 3.2 Cell Selection and
Reselection.

eRAN12.1 Draft A (2016-12-30)


Draft A (2016-12-30) of eRAN12.1 introduces the following changes to Issue 05
(2016-10-08) of eRAN11.1.

Change Change Description Parameter Change Affected


Type Entity

Feature Added the function that operators can Added the parameter Macro/
change prevent certain non-serving E-UTRA value Micro/
frequencies from being delivered in UNDELIVER(UND LampSite
SIB5. For details, see Inter-Frequency ELIVER) to
or Inter-RAT Measurement in 3.2.5 EutranInterNFreq.
Neighboring Cell Measurement for MeasPerformance-
Cell Reselection and Cell Reselection Demand.
in 4.3 LBFD-00201803 Cell Selection
and Re-selection and 6.4 Parameter
Optimization.
Added descriptions of the BTS3912E.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 2


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 1 About This Document

Change Change Description Parameter Change Affected


Type Entity

Editorial None None -


change

1.4 Differences Between eNodeB Types


The features described in this document are implemented in the same way on macro, micro,
and LampSite eNodeBs.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 3


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 2 Overview

2 Overview

2.1 Introduction
In an Evolved Universal Terrestrial Radio Access Network (E-UTRAN), UEs can be either in
RRC_CONNECTED or RRC_IDLE mode. RRC is short for radio resource control.
After being powered on, UEs will be in RRC_IDLE mode (also known as idle mode) if no
RRC connection is established between the UEs and the E-UTRAN.

2.2 Benefits
With idle mode management, the eNodeB includes configurations in system information
broadcasts, and the UEs select suitable cells to camp on and obtain services based on these
configurations. Idle mode management increases the UE access success rate, improves the
quality of service, and ensures that UEs camp on cells with good signals.

2.3 Relate Concepts

2.3.1 PLMN
A PLMN identity consists of a Mobile Country Code (MCC) and a Mobile Network Code
(MNC).

EPLMN
The equivalent PLMN (EPLMN) list is a list of PLMNs considered as equivalents to
Registered PLMNs (RPLMNs) in terms of service provisioning. During PLMN selection, a
UE preferentially selects a PLMN from the list. The EPLMN list plus RPLMN is sent from
the EPC and stored in the UE during an Attach procedure and TA update. An EPLMN list can
contain more than one EPLMN.

HPLMN
The home PLMN (HPLMN) is the PLMN in which the UE is defined.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 4


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 2 Overview

VPLMN
The visited PLMN (VPLMN) is the PLMN where the UE is located. A VPLMN can be the
HPLMN.

EHPLMN
An equivalent home PLMN (EHPLMN) is an equivalent to the HPLMN, and takes
precedence over the HPLMN. The EHPLMN list is stored in the Universal subscriber identity
module (USIM) of the UE. During PLMN selection, the UE takes into account both the
EHPLMNs and the HPLMN that is extracted from the international mobile subscriber identity
(IMSI), and preferentially selects an EHPLMN.

RPLMN
The registered PLMN (RPLMN) is the PLMN on which the UE has performed a location
registration successfully by TA update.

2.3.2 Access Classes


Access classes are applicable to UE access on the radio interface. There are 16 access classes,
numbered from 0 to 15. The information about access classes 0 to 9 and 11 to 15 is stored in
USIMs. The information about access class 10, indicating whether cells allow emergency
calls, is signaled to the UEs through system information broadcast.
l Access classes 0 to 9 are ordinary classes. Each UE is randomly allocated one out of
these ten classes. UEs of these classes can obtain services in their HPLMN, EPLMN, and
VPLMNs.
l Access classes 11 to 15 are special classes. They are allocated to specific high-priority
users. Each UE may be allocated one or more of the five classes. These special access
classes are described as follows:
UEs of access classes 11 and 15 can receive services only in their HPLMN and
EHPLMNs. If the EHPLMN list is absent, access classes 11 and 15 can only be used in
the HPLMN.
Class 11: for PLMN use
Class 15: for PLMN staff
Access classes 12 to 14 are applicable in the HPLMN and VPLMNs of the home country
only.
Class 12: for security services
Class 13: for public utilities
Class 14: for emergency services
l If access class 10 is barred, UEs of access classes 0 to 9 or UEs without USIMs are not
allowed to initiate emergency calls. For UEs of access classes 11 to 15, emergency calls
are not allowed if both access class 10 and the relevant access class (within the range
from 11 to 15) are barred.

2.3.3 Service Types


The services that UEs in idle mode can obtain include the following types:
l Limited service

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 5


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 2 Overview

A UE can initiate only emergency calls in an Acceptable Cell. Such a cell should meet
the requirements that the cell is not barred and the cell selection criteria are fulfilled. The
UE camps on the Acceptable Cell to obtain Limited service when the cell is part of at
least one TA on the list of forbidden TAs for roaming or when the cell does not belong to
the RPLMN. For details about the cell selection criteria, see 3.2.2 Cell Selection.
l Normal service
A UE obtains normal service in a Suitable Cell. Such a cell should meet all the following
requirements:
The cell is part of the selected PLMN, the RPLMN, or a PLMN on the EPLMN list.
The cell is part of at least one TA that belongs to a PLMN fulfilling the previous
requirement but is not on the list of forbidden TAs for roaming. For details, see
section 3.1 "PLMN selection and roaming" in 3GPP TS 23.122 R10, which was
released in March 2011.
The cell is not barred.
The cell selection criteria are fulfilled.
l Operator service
A UE obtains operator service in a Reserved Cell, which is used by the operator only. In
the case of access class 11 or 15 in the HPLMN or an EHPLMN, a UE may consider
Reserved Cells as candidates during cell selection or reselection. In other cases, a UE
regards Reserved Cells as barred during cell selection or reselection. UEs are not allowed
to camp on barred cells.
NOTE

Whether a cell is barred can be set through the CellAccess.CellBarred parameter, and this
parameter setting is delivered through system information block type 1 (SIB1). Whether a cell is a
Reserved Cell can be set through the CellOp.CellReservedForOp parameter by the operator. This
parameter setting is also delivered in SIB1.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 6


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

3 Technical Description

Figure 3-1 shows the key procedure of idle mode management.

Figure 3-1 Key procedure of idle mode management

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 7


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

3.1 PLMN Selection


UEs select a public land mobile network (PLMN) and register on the PLMN. Figure 3-2
shows the PLMN selection procedure.
When a UE is powered on, or returns from an area with no signal coverage:
1. The UE first selects the last RPLMN or a PLMN in the EPLMN list and attempts to
register on the selected PLMN.
2. If the registration on that PLMN is successful, the selected PLMN is displayed on the
UE, and the UE can now obtain services from the operator. If the last RPLMN is
unavailable or if the registration on the selected PLMN fails, another PLMN can be
selected, either automatically or manually, depending on the PLMN priority information
stored in the USIM.
For details about PLMN selection, see section 4.4 in 3GPP TS 23.122 R10, which was
released in March 2011.

Figure 3-2 PLMN selection procedure

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 8


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

3.1.1 PLMN Selection in Automatic Mode


If a UE fails to register on its most recent RPLMN or EPLMN, the UE attempts to select
another PLMN. In automatic network selection mode, the UE selects a PLMN in the
following preferential order:

1. The EHPLMN with the highest priority if the EHPLMN list is present and is not empty,
or the HPLMN if the EHPLMN list is not present or is empty.
2. Each PLMN/radio technology combination in the User Controlled PLMN Selector
with Access Technology data file in the USIM, in priority order.
3. Each PLMN/radio technology combination in the Operator Controlled PLMN
Selector with Access Technology data file in the USIM, in priority order.
4. Other high-quality PLMN/radio technology combinations, in a random order. If the
reference signal received power (RSRP) value of a cell in the PLMN/radio technology
combination is greater than or equal to 110 dBm, the combination is considered a high
quality PLMN/radio technology combination.
5. Other PLMN/radio technology combinations in order of decreasing signal quality.

When the UE finds a Suitable Cell in a PLMN following this procedure, the UE attempts to
register on the PLMN. If the registration is successful, the UE camps on the Suitable Cell;
otherwise, the UE tries the next PLMN.

If the registration on none of the PLMNs is successful, the UE enters the Limited service
state. If no PLMN is available, the UE cannot obtain any services.

NOTE

Limited service, Normal service, and Operator service are three service types that can be provided for
UEs in idle mode in Acceptable Cell, Suitable Cell, and Reserved Cell, respectively. For details about
Acceptable Cell, Suitable Cell, and Reserved Cell, see section 4.3 in 3GPP TS 36.304 R10, which was
released in March 2011.

3.1.2 PLMN Selection in Manual Mode


If a UE fails to register on its most recent RPLMN or EPLMN, the UE attempts to select a
new PLMN. For manual network selection, the UE displays a list of detected PLMNs in the
same order as the PLMNs to be selected for automatic network selection.

In manual mode, the UE can also try forbidden PLMNs, which are determined by the EPC. If
the UE successfully registers on the selected PLMN, the UE no longer considers the PLMN to
be forbidden.

3.1.3 Roaming
When roaming, a UE obtains services from a VPLMN other than its HPLMN. For example,
the UE may obtain services from a PLMN in another country (an international roaming area).
When the UE with the roaming service moves out of the coverage area of its HPLMN, the UE
can obtain services from another PLMN according to the PLMN information stored on the
USIM. The operator determines whether roaming is allowed for a UE.

After the UE registers with a VPLMN by roaming, it periodically searches for its HPLMN
and attempts to return to it. The time interval between consecutive searches for the HPLMN is
defined by the operator and stored on the USIM.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 9


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

3.2 Cell Selection and Reselection


This section describes the basic feature LBFD-00201803 Cell Selection and Re-selection.
After selecting a PLMN, a UE selects a cell in the PLMN to camp on. After camping on the
cell, the UE monitors system information, performs measurements on the serving cell and
neighboring cells based on measurement rules, and selects a better cell to camp on based on
cell reselection criteria. The UE performs cell selection or reselection using the selection- or
reselection-related parameters from the system information or from the RRC Connection
Release message.
Figure 3-3 shows the cell selection and cell reselection procedures. For details, see section
5.2.2 in 3GPP TS 36.304 R10, which was released in March 2011.

Figure 3-3 Cell selection and reselection procedures

NOTE

For details about the cell reselection triggering conditions, see 3.2.6 Intra-Frequency or Equal-
Priority Inter-Frequency Cell Reselection, 3.2.7 Different-Priority Inter-Frequency or Inter-RAT
Cell Reselection, and 3.2.8 Speed-based Cell Reselection.

3.2.1 Cell Search


Cell search is a procedure in which a UE achieves time and frequency synchronization with a
cell, obtains the physical cell identifier (PCI), and learns the signal quality and other

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 10


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

information about the cell based on the PCI. A UE performs cell search on all frequencies
before selecting or reselecting to a cell.

In an LTE system, two types of synchronization signals are used for cell search: primary
synchronization signals (PSSs) and secondary synchronization signals (SSSs). The cell search
procedure is as follows:

1. A UE monitors the PSS to acquire clock synchronization accurate to within 5 ms, and to
identify the cell identities in possible cell identity groups the PCI belongs to.
2. The UE monitors the SSSs to acquire frame synchronization, that is, time
synchronization, and to identify the cell identity groups based on the one-to-one
relationship with SSSs.
3. The UE identifies the PCI by cross-referencing the identified cell identity and cell
identity group.
4. The UE monitors the downlink reference signal to determine the signal quality in the
cell.
5. The UE reads information on the broadcast channel (BCH) to acquire related details
about the cell.

NOTE

l In an E-UTRAN, cell identities are grouped to reduce the number of correlation detections,
simplifying PCI identification.
l Each cell identity group consists of three cell identities.

3.2.2 Cell Selection


When a UE transitions from connected mode to idle mode or after it has selected a PLMN, the
UE must select a cell to camp on.

When the UE transitions from connected mode to idle mode:

1. The UE first attempts to select the most recent cell it has camped on in connected mode,
or it selects a Suitable Cell on a frequency that is allocated through the RRC Connection
Release message.
2. If such a cell is not available, the UE attempts to find a Suitable Cell by performing the
Stored Information Cell Selection procedure.
3. If the UE fails to find a Suitable Cell, the UE performs the Initial Cell Selection
procedure.

Stored Information Cell Selection


The Stored Information Cell Selection procedure requires stored information related to carrier
frequencies and cell parameters. The information is retrieved from previous measurement
control information elements or from preexisting SI messages. This information can help
speed up cell selection.

The Stored Information Cell Selection procedure is as follows:

The UE searches known carrier frequencies for a Suitable Cell.

l If the UE finds a Suitable Cell, it selects that cell to camp on.


l If the UE fails to find a Suitable Cell, it initiates the Initial Cell Selection procedure.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 11


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

Initial Cell Selection


The Initial Cell Selection procedure does not require that the UE know in advance which
frequencies are E-UTRA carrier frequencies.
In this procedure, the UE scans all carrier frequencies on the supported E-UTRAN bands to
find a Suitable Cell. On each carrier frequency, the UE searches for the strongest cell only. If
the UE finds a Suitable Cell, it selects that cell to camp on. If the UE fails to find a Suitable
Cell, it selects an Acceptable Cell to camp on.

Cell Selection Criteria


During cell selection, a UE selects an E-UTRAN cell that meets cell selection criteria.
A UE selects an E-UTRAN cell to camp on when both Srxlev and Squal are greater than zero.
where
Srxlev = Qrxlevmeas (Qrxlevmin + Qrxlevminoffset) - Pcompensation
Squal = Qqualmeas (Qqualmin + Qqualminoffset)
The variables in the preceding formulas are described as follows:
l Qrxlevmeas is the measured cell RX signal level (RSRP value) of the cell.
l Qrxlevmin is the minimum cell RX signal level. It is broadcast in SIB1 and set by the
CellSel.QRxLevMin parameter.
l Qrxlevminoffset is the offset to Qrxlevmin. It is broadcast in SIB1 and set by the
CellSel.QRxLevMinOffset parameter. The UE camping on a cell in a VPLMN considers
this offset parameter when it attempts to camp on a cell in a higher-priority PLMN
during periodic cell reselection. The cell in the higher-priority PLMN delivers the value
of this parameter to the UE for the Srxlev evaluation.
l Pcompensation is the result of the function: max (PMax UE Maximum Output Power,
0).
PMax is the maximum transmit power that the UE can apply to uplink transmission.
It is broadcast in SIB1 and set by the CELL.UePowerMax parameter.
UE Maximum Output Power is the maximum output power that the UE can
physically achieve. It is not configurable on the network side.
l Qqualmeas is the measured cell RX signal quality (RSRQ value) of the cell.
l Qqualmin is the minimum cell RX signal quality required for the cell to become a
Suitable Cell. It is broadcast in SIB1 and set by the CellSel.QQualMin parameter. The
CellResel.ThrshServLowQCfgInd and CellSel.QQualMin settings determine whether
the Qqualmin IE is delivered in SIB1:
When the value of CellSel.QQualMin is not 0, CellResel.ThrshServLowQCfgInd
can be set to CFG(Configure) or NOT_CFG(Not configure). In this case, the
Qqualmin IE is delivered in SIB1.
When the value of CellSel.QQualMin is 0, CellResel.ThrshServLowQCfgInd can
only be set to NOT_CFG(Not configure). In this case, the Qqualmin IE is not
delivered in SIB1.
For details, see section 6.2.2 "SystemInformationBlockType1" in 3GPP TS 36.331 R10,
which was released in March 2011.
l Qqualminoffset is the offset to Qqualmin. It is broadcast in SIB1 and set by the
CellSel.QQualMinOffset parameter. The UE camping on a cell in a VPLMN considers

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 12


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

this offset parameter when it attempts to camp on a cell in a higher-priority PLMN


during periodic cell reselection. The cell in the higher-priority PLMN delivers the value
of this parameter to the UE for the Squal evaluation.

3.2.3 Neighboring Cell Priority Handling


After camping on a cell, a UE may attempt to reselect to and then camp on another cell.
Before cell reselection, the UE is required to measure the signal quality level of neighboring
cells. The UE then reselects to a neighboring cell by using a specific cell reselection criterion
according to the priority of the neighboring cell.

During measurement and implementation of cell reselection, the UE needs to obtain the
priorities of neighboring frequencies. Note that frequencies of different RATs must be
configured with different priorities. During the evaluation for reselection to an intra-frequency
neighboring cell, the UE ignores the priority of the target frequency because cells working on
the same frequency have the same priority.

The priorities for E-UTRAN frequencies and inter-RAT frequencies include common
priorities and dedicated priorities.

Common Priority
The priority of the serving frequency is specified by CellResel.CellReselPriority and
broadcast in system information block type 3 (SIB3).

The priority of the non-serving E-UTRA frequency is specified by


EutranInterNFreq.CellReselPriority and broadcast in SIB5. A maximum of 16 non-serving
E-UTRA frequencies can be broadcast.
NOTE

Each UMPT board can be configured with a maximum of 16 non-serving E-UTRA frequencies, while
other boards can be configured with no more than 8.

The priority of the neighboring UTRAN frequency is specified by


UtranNFreq.CellReselPriority and broadcast in SIB6. A maximum of 16 neighboring
UTRAN frequencies can be broadcast.

The priority of the neighboring GERAN frequency is specified by


GeranNfreqGroup.CellReselPriority and broadcast in SIB7. A maximum of 16 neighboring
GERAN frequency groups can be broadcast.

The priority of a neighboring CDMA2000 frequency is specified by


Cdma2000BandClass.Cdma20001XrttCellReselPri and
Cdma2000BandClass.Cdma2000HrpdCellReselPri and broadcast in SIB8.

Dedicated Priority
During release of UE radio resources, the IdleModeMobilityControlInfo (IMMCI) IE in the
RRC Connection Release message delivers the radio resources for each UE. A maximum of
16 non-serving E-UTRA frequencies, 16 neighboring UTRAN frequencies, and 16
neighboring GERAN frequency groups can be delivered for each UE.

Cell reselection dedicated priorities include dedicated SPID priorities and operator-specific
dedicated priorities.
l SPID dedicated priority

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 13


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

Specifies a dedicated cell reselection priority using the SPID. An SPID dedicated priority
can be either a common SPID priority or an operator-based SPID priority. The former
refers to an SPID priority configured not based on PLMN, and the latter refers to an
SPID priority configured based on the PLMN of the serving cell. For details about SPID
dedicated priorities, see descriptions of LOFD-00105401 Camp & Handover Based on
SPID in Flexible User Steering Feature Parameter Description.
On a shared network, the eNodeB uses LOFD-001133 Multi Operators SPID Policy to
implement the operator-specific SPID dedicated priority function for cell reselection.
Specifically, operators sharing the same eNodeB can select their respective SPID value
ranges, without negotiating with each other, and the shared eNodeB allows users of
different operators to use the same SPID for different cell reselection dedicated priority
policies. For details, see RAN Sharing Feature Parameter Description.
l Operator-specific dedicated priority
Dedicated priority based on the home operator of a neighboring frequency:
Specifies a dedicated cell reselection priority based on the operator to which an
adjacent frequency belongs.
In RAN Sharing scenarios, the dedicated priorities of E-UTRAN, UTRAN, and
GERAN frequencies are specified by EutranNFreqRanShare.CellReselPriority,
UtranRanShare.CellReselPriority, and GeranRanShare.CellReselPriority,
respectively, for different PLMNs.
Dedicated priority based on home operator of the serving cell: Specifies a dedicated
cell reselection priority based on the PLMN ID of the serving cell. The priorities are
specified by EutranNFreqSCellOp.CellReselDediPri,
UtranNFreqSCellOp.CellReselDediPri,
GeranNFGroupSCellOp.CellReselDediPri,
Cdma2000BcSCellOp.Cdma1XrttCellReselDediPri, and
Cdma2000BcSCellOp.HrpdCellReselDediPri.
Both dedicated priority based on home operator of an adjacent frequency and dedicated
priority based on home operator of the serving cell are operator-specific dedicated
priorities. Only one type can be used at a time.

The eNodeB preferentially uses SPID dedicated priorities when determining the dedicated
frequency priorities to carry in the RRC Connection Release message. If no SPID priority is
configured for the UE, the eNodeB uses the dedicated frequency priorities of operators
configured in the EutranNFreqRanShare, UtranRanShare, and GeranRanShare MOs, or
the frequency priorities of UE-homed operators configured in the EutranNFreqSCellOp,
UtranNFreqSCellOp, GeranNFGroupSCellOp, and Cdma2000BcSCellOp MOs. If no
dedicated priority of operators is configured, the eNodeB does not carry dedicated frequency
priorities in the RRC Connection Release message. There are two exceptions:
l For a CA UE, when the idle-mode PCC anchoring function takes effect, if no SPID
dedicated priority or operator-specific dedicated priority is configured, the eNodeB still
carries the dedicated frequency priorities generated by this function in the RRC
Connection Release message. For details about the idle-mode PCC anchoring function,
see Carrier Aggregation Feature Parameter Description.
l For a UE release due to system overload, MME overload, or S1-interface faults, even if
the eNodeB does not use any of the preceding dedicated priorities, if the common
priority of the neighboring frequency is lower than the common priority of the serving
frequency, the eNodeB uses the common priority of the serving frequency as the
dedicated priority of a neighboring frequency and carries the priority in the RRC
Connection Release message.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 14


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

When the eNodeB determines the list of frequency priorities to carry in the RRC Connection
Release message, it filters frequencies based on UE capabilities and on the target PLMN.
l UE capability-based frequency filtering
If the eNodeB has obtained UE capabilities, it filters out frequencies that UEs do
not support based on systems supported by UEs and UE frequency capabilities.
NOTE

If the UE supports enhanced measurement frequency capabilities (UE capability reported in


"incMonEUTRA" is TRUE), the eNodeB sends dedicated priorities for a maximum of 16
frequencies. Otherwise, the eNodeB sends dedicated priorities for a maximum of eight
frequencies, for which the value of the EutranInterNFreq.MeasPerformanceDemand
parameter is NORMAL(NORMAL).
If the eNodeB has not obtained UE capabilities, it checks the value of
CellAlgoSwitch.ReselecPriAdaptSwitch and determines the cause value of RRC
access request.
If CellAlgoSwitch.ReselecPriAdaptSwitch is set to ON(On) and the cause value of
RRC access request is mo-Signalling (such as TAU accept/reject and attach reject),
and the S1 release is initiated by the MME with the cause value NAS, the eNodeB
assumes that UEs support all frequencies in the priority list and filtering is not
required.
Otherwise, the eNodeB assumes that UEs support only the frequencies of the
serving cell. In this case, if frequencies of the serving cell are included in the
frequency list, they are reserved and other frequencies are filtered out. If
frequencies of the serving cell are not included in the frequency list, the eNodeB
does not deliver the IMMCI IE.
l Target PLMN-based filtering
If all home PLMNs of external cells under the frequency are not included in the
target PLMN list, the eNodeB filters out the frequency.
If no external cells are configured on the frequency (no PLMN information of
external cells), the eNodeB fails to obtain PLMN attributes of the frequency and
filters out the frequency.

The eNodeB includes remaining frequencies in the IMMCI IE and delivers it to UEs.

During cell reselection, when a UE camps on a Suitable Cell, the UE ignores all the absolute
priorities provided in system information if dedicated priorities are assigned through
dedicated signaling. If the UE acquires the priorities of other frequencies but no priority of the
serving frequency, the UE regards the priority of the serving frequency as the lowest.

During cell reselection, when a UE camps on an Acceptable Cell, the UE uses only the
absolute priorities provided in system information. The UE only stores the information about
the dedicated priorities but does not use it for cell reselection even when dedicated priorities
are available.

A UE discards priorities provided by dedicated signaling in any of the following situations:

l The NAS signals the AS to perform PLMN selection.


l The UE enters the connected mode.
l The validity time (specified by T320) of the dedicated priority expires.

T320 and the dedicated priority are sent to the UE in the RRC Connection Release message.
The eNodeB determines the value of T320 in the following two ways:

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 15


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

l If the dedicated priority is obtained through the UE's SPID mapping or the PCC
anchoring function, the value of T320 is always 180 minutes.
l If the dedicated priority is obtained through other means, T320 is specified by the
RrcConnStateTimer.T320ForLoadBalance parameter during an RRC connection
release due to load balancing, or by the RrcConnStateTimer.T320ForOther parameter
during an RRC connection release due to other reasons.

For details about T320, see section 7.3 in 3GPP TS 36.331 R10, released in March 2011.

3.2.4 Blacklisted Cell Identifying


During cell reselection, UEs are not allowed to measure or reselect to the blacklisted cells of
the serving cell. Blacklisted cells are classified into intra-frequency and inter-frequency
blacklisted cells.

l Information about intra-frequency blacklisted cells is delivered in


IntraFreqBlackCellList of the SIB4 and is excluded from IntraFreqNeighCellList of the
SIB4.
l Information about inter-frequency blacklisted cells is delivered in InterFreqBlackCellList
of the SIB5 and is excluded from InterFreqNeighCellList of the SIB5.

UEs identify blacklisted cells by PCIs.

An intra-frequency blacklisted cell can be configured in the IntraFreqBlkCell MO. The first
16 E-UTRAN intra-frequency blacklisted cells are the blacklisted cells in intra-frequency idle
mode. In this MO, IntraFreqBlkCell.PhyCellId specifies the starting PCI of an intra-
frequency blacklisted cell list, and IntraFreqBlkCell.PhyCellIdRange specifies the number
of consecutive PCIs from the starting PCI specified by IntraFreqBlkCell.PhyCellId
onwards.

An inter-frequency blacklisted cell can be configured in the InterFreqBlkCell MO. The first
16 E-UTRAN inter-frequency blacklisted cells are the blacklisted cells in inter-frequency idle
mode. In this MO, InterFreqBlkCell.DlEarfcn specifies the downlink EARFCN
corresponding to the blacklist, InterFreqBlkCell.PhyCellId specifies the starting PCI in the
blacklist, and InterFreqBlkCell.PhyCellIdRange specifies the number of consecutive PCIs
from the starting PCI specified by InterFreqBlkCell.PhyCellId onwards.

3.2.5 Neighboring Cell Measurement for Cell Reselection


During cell reselection, UEs perform measurements of neighboring cells based on the signal
quality of the serving cell and frequency priorities of the neighboring cells. The UE measures
only the neighboring frequencies broadcast in the system information and the neighboring
frequency whose priority information is carried in the RRC Connection Release message.

Intra-Frequency Measurement
To trigger intra-frequency measurements, the following rules apply:

The UE does not perform intra-frequency measurements if the Srxlev and Squal values of the
serving cell are greater than SIntraSearchP and SIntraSearchQ, respectively. The UE performs intra-
frequency measurements if the Srxlev or Squal value of the serving cell is not greater than
SIntraSearchP or SIntraSearchQ, respectively. For details about how to calculate the Srxlev and
Squal values, see 3.2.2 Cell Selection.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 16


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

The following table provides reference for determining the values of SIntraSearchP and
SIntraSearchQ:

CellResel.SInt CellResel.Q IEs SIntraSearchP SIntraSearchQ


raSearchCfgIn QualMinCfg Broadcast in Value Value
d Ind SIB3

NOT_CFG(Not CFG(Configu s- s-IntraSearchP s-IntraSearchQ


configure) re) IntraSearchP
and s-
IntraSearchQ

CFG(Configure NOT_CFG(N s-IntraSearch s-IntraSearch 0 dB


) ot configure)

NOT_CFG(Not NOT_CFG(N N/A(1) Infinity(1) 0 dB(1)


configure)(1) ot configure)
(1)

CFG(Configure CFG(Configu s-IntraSearch, s-IntraSearchP s-IntraSearchQ


) re) s-
IntraSearchP,
and s-
IntraSearchQ

NOTE

(1):
In this case, a UE measures the information about intra-frequency cells, regardless of whether the
signal quality is good in the serving cell.

Both s-IntraSearch and s-IntraSearchP broadcast in SI are specified by the


CellResel.SIntraSearch parameter, and s-IntraSearchQ is specified by the
CellResel.SIntraSearchQ parameter.
When CellResel.QQualMinCfgInd is set to CFG(Configure) and
CellResel.SIntraSearchCfgInd is set to NOT_CFG(Not configure),
CellResel.SIntraSearch cannot be configured. In this case, s-IntraSearchP uses the default
value or last correctly configured value of CellResel.SIntraSearch.

Inter-Frequency or Inter-RAT Measurement


To trigger inter-frequency or inter-RAT measurements, the following rules apply:
l The UE always performs measurements on inter-frequency or inter-RAT neighboring
cells regardless of the signal quality of the serving cell if the priorities of the neighboring
frequencies are higher than the priority of the serving frequency.
l If the priorities of non-serving E-UTRA frequencies are lower than or equal to the
priority of the serving frequency, or if the priorities of inter-RAT neighboring frequencies
are lower than the priority of the serving frequency, the UE determines whether to start
the corresponding measurements according to the following rules:
The UE does not perform inter-frequency or inter-RAT measurements if the Srxlev
and Squal values of the serving cell are greater than SnonIntraSearchP and
SnonIntraSearchQ, respectively. SnonIntraSearchP indicates the Srxlev threshold for

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 17


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

triggering inter-frequency or inter-RAT measurements. SnonIntraSearchQ indicates the


Squal threshold for triggering inter-frequency or inter-RAT measurements.
The UE performs inter-frequency or inter-RAT measurements if the Srxlev or Squal
value of the serving cell is not greater than SnonIntraSearchP or SnonIntraSearchQ,
respectively.
The following table provides reference for determining the values of SnonIntraSearchP and
SnonIntraSearchQ:

CellResel.SN CellResel. IEs SnonIntraSearchP SnonIntraSearch


onIntraSearc QQualMin Broadcast in Value Q Value
hCfgInd CfgInd SIB3

NOT_CFG(N CFG(Config s- s- s-
ot configure) ure) NonIntraSea NonIntraSearc NonIntraSearc
rchP and s- hP hQ
NonIntraSea
rchQ

CFG(Configu NOT_CFG( s- s- 0 dB
re) Not NonIntraSea NonIntraSearc
configure) rch h

NOT_CFG(N NOT_CFG( N/A(1) Infinity(1) 0 dB(1)


ot configure) Not
(1) configure)(1)

CFG(Configu CFG(Config s- s- s-
re) ure) NonIntraSea NonIntraSearc NonIntraSearc
rchP, s- hP hQ
NonIntraSea
rchQ, and s-
NonIntraSea
rch

NOTE

(1):UEs measure both inter-frequency and inter-RAT cells, regardless of whether the signal quality
in the serving cell is good.
Both s-NonIntraSearch and s-NonIntraSearchP broadcast in SI are specified by the
CellResel.SNonIntraSearch parameter, and s-NonIntraSearchQ is specified by the
CellResel.SNonIntraSearchQ parameter.
When CellResel.QQualMinCfgInd is set to CFG(Configure) and
CellResel.SNonIntraSearchCfgInd is set to NOT_CFG(Not configure),
CellResel.SNonIntraSearch cannot be configured. In this case, s-NonIntraSearchP
uses the default value or last correctly configured value of CellResel.SNonIntraSearch.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 18


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

NOTE

For non-serving E-UTRA frequencies configured in the EutranInterNFreq MO:


l If the UE does not support enhanced measurement frequency capabilities (that is, UE capability
reported in "incMonEUTRA" is not TRUE), the UE can choose a frequency for which
EutranInterNFreq.MeasPerformanceDemand is set to NORMAL(NORMAL) as the target
frequency for cell reselection.
l Otherwise, the UE can obtain all the configured non-serving E-UTRA frequencies from SI. For
frequencies with EutranInterNFreq.MeasPerformanceDemand set to NORMAL(NORMAL), the
UE performs measurements based on normal measurement performance. For frequencies with
EutranInterNFreq.MeasPerformanceDemand set to REDUCED(REDUCED), the UE performs
measurements based on reduced measurement performance. In this case, the time to reselect to such
a frequency may increase.
l Non-serving E-UTRA frequencies with EutranInterNFreq.MeasPerformanceDemand set to
UNDELIVER(UNDELIVER) are not delivered in SIB5, and UEs do not measure these non-
serving E-UTRA frequencies.

3.2.6 Intra-Frequency or Equal-Priority Inter-Frequency Cell


Reselection
During cell reselection, intra-frequency or equal-priority inter-frequency neighboring cells
must meet both cell selection and reselection criteria.

1. The cell selection criteria are described in Cell Selection Criteria. The criteria for intra-
and inter-frequency neighboring cells involve the following values:
l Intra-frequency neighboring cells
The following values broadcast in SIB3 are used to calculate Srxlev and Squal:
Qrxlevmin: the minimum cell RX signal level
It is set by the CellResel.QRxLevMin parameter.
PMax: the maximum UE transmit power in a neighboring cell
It is set by the CellResel.PMax parameter.
Qqualmin: the minimum cell RX signal quality
It is set by the CellResel.QQualMin parameter.
Qrxlevminoffset and Qqualminoffset
For details, see 3.2.2 Cell Selection.
l Inter-frequency neighboring cells
The following values broadcast in SIB5 are used to calculate Srxlev and Squal:
Qrxlevmin: the minimum cell RX signal level
It is set by the EutranInterNFreq.QRxLevMin parameter.
PMax: the maximum UE transmit power in a neighboring cell
It is set by the EutranInterNFreq.PMax parameter.
Qqualmin: the minimum cell RX signal quality
It is set by the EutranInterNFreq.QQualMin parameter.
2. Once these cell selection criteria are met, cell reselection criteria are considered. If a UE
has camped on its serving cell for more than one second, it reselects a neighboring cell
that also meets both of the following conditions:
l The neighboring cell has the highest cell-ranking criterion (represented by R_n).

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 19


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

l The R_n of the neighboring cell is higher than the cell-ranking criterion (represented by
R_s) of the serving cell during the cell reselection time.
The cell reselection time for an intra-frequency neighboring cell is broadcast in SIB3 and
set by the CellResel.TreselEutran parameter. The cell reselection time for an inter-
frequency neighboring cell is broadcast in SIB5 and set by the
EutranInterNFreq.EutranReselTime parameter.
NOTE

During cell reselection, the UE also needs to check whether access to a neighboring cell is allowed
according to the "cellAccessRelatedInfo" IE in SIB1 sent from the neighboring cell. If the neighboring
cell is barred, it must be excluded from the candidate list. If the neighboring cell cannot function as a
Suitable Cell because it is in the list of forbidden TAs for roaming or it does not belong to the RPLMN
or an EPLMN, the UE does not consider this neighboring cell and other cells on the same frequency as
candidates for reselection within 300 seconds.

The cell-ranking criteria R_s for the serving cell and R_n for neighboring cells are defined as
follows:
R_s = Qmeas,s + Qhyst
R_n = Qmeas,n Qoffset
l Qmeas,s: the measured RSRP of the serving cell
l Qhyst: the reselection hysteresis for the serving cell, broadcast in SIB3
It is set by the CellResel.Qhyst parameter.
l Qmeas,n: the measured RSRP of a neighboring cell.
l Qoffset:
Intra-frequency neighboring cells
It is equal to q-OffsetCell, which is broadcast in SIB4 and set by the
EutranIntraFreqNCell.CellQoffset parameter. If q-OffsetCell is not broadcast in
SIB4, the UE sets q-OffsetCell to 0.
Inter-frequency neighboring cells
It is equal to q-OffsetCell plus q-OffsetFreq, which are broadcast in SIB5 and set by
the EutranInterFreqNCell.CellQoffset and EutranInterNFreq.QoffsetFreq
parameters, respectively. If q-OffsetCell is not broadcast in SIB5, the UE sets q-
OffsetCell to 0.
SIB4 and SIB5 broadcast a maximum of 16 intra-frequency neighboring cells or 16 inter-
frequency neighboring cells of a frequency. The eNodeB supports a maximum of 256 intra-
and inter-frequency neighboring cells in total. The eNodeB selects intra- and inter-frequency
neighboring cells by using the following rules in sequence:
1. Neighboring cells for which the following two parameters are set to 0 are not broadcast:
- EutranIntraFreqNCell.CellQoffset
- EutranInterFreqNCell.CellQoffset
2. Neighboring cells for which the following two parameters are set to HIGH are
preferentially broadcast:
- EutranIntraFreqNCell.CellMeasPriority
- EutranInterFreqNCell.CellMeasPriority
3. If there are more than 16 neighboring cells, the 16 neighboring cells with the largest
values for the following two parameters are broadcast:
- EutranIntraFreqNCell.CellQoffset

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 20


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

- EutranInterFreqNCell.CellQoffset
4. If there are less than 16 neighboring cells, neighboring cells meeting both of the
following conditions are added until there is a total of 16 neighboring cells:
- The EutranIntraFreqNCell.CellMeasPriority and
EutranInterFreqNCell.CellMeasPriority parameters are set to LOW.
- The EutranIntraFreqNCell.CellQoffset and EutranInterFreqNCell.CellQoffset
values are the largest.
All these 16 neighboring cells are then broadcast.

3.2.7 Different-Priority Inter-Frequency or Inter-RAT Cell


Reselection
Reselection to a different-priority inter-frequency cell or an inter-RAT cell can be classified as
either reselection to a higher-priority cell or reselection to a lower-priority cell.

Inter-Frequency/Inter-RAT Cell Selection Criteria


The Srxlev and Squal values of inter-frequency or inter-RAT neighboring cells need to be
calculated when the UE reselects to an inter-frequency or inter-RAT neighboring cell. The
Srxlev and Squal values are calculated as follows:
l Inter-frequency neighboring cell: See 3.2.6 Intra-Frequency or Equal-Priority Inter-
Frequency Cell Reselection.
l Neighboring UTRAN cell
Srxlev = Qrxlevmeas - (Qrxlevmin + Qrxlevminoffset) - Pcompensation
Squal = Qqualmeas - (Qqualmin + Qqualminoffset)
Pcompensation = max(UE_TXPWR_MAX_RACH - P_MAX, 0)
Qrxlevmeas is the measured RX signal level of the neighboring UTRAN cell.
Qqualmeas is the measured RX signal quality of the neighboring UTRAN cell.
The values of these parameters are broadcast in SIB6 from the E-UTRAN when the UE
implements reselection estimation on a neighboring UTRAN cell.
Qrxlevmin is set by the UtranNFreq.QRxLevMin parameter.
Qqualmin is set by the UtranNFreq.Qqualmin parameter.
UE_TXPWR_MAX_RACH is set by the UtranNFreq.PmaxUtran parameter.
P_MAX is the maximum output power that the UE can physically provide. It is not
configurable on the network side.
Values of Qrxlevminoffset and Qqualminoffset are obtained from UTRAN system
information. For details, see section 5.2.3.1 in 3GPP TS 25.304 R10, which was released
in March 2011.
l Neighboring GERAN cell
Srxlev = Qrxlevmeas - Qrxlevmin - Pcompensation
Qrxlevmeas is the measured RX signal level of the neighboring GERAN cell.
Pcompensation = max(MS_TXPWR_MAX_CCH - P, 0)
The values of these parameters are broadcast in SIB7 from the E-UTRAN when the UE
implements reselection estimation on a neighboring GERAN cell.
Qrxlevmin is set by the GeranNfreqGroup.QRxLevMin parameter.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 21


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

MS_TXPWR_MAX_CCH is set by the GeranNfreqGroup.PmaxGeran parameter.


P is the maximum output power that the UE can physically provide.
It is not configurable on the network side. For details, see section 3.6 "Radio constraints"
in 3GPP TS 43.022 R10, which was released in March 2011.
l Neighboring CDMA2000 cell

Ec/Io is the measured RX signal quality of the neighboring CDMA2000 cell.


For details, see 3GPP2 C.S0005-A.

Criteria for Reselection to a Higher-Priority Cell


If CellResel.ThrshServLowQCfgInd is set to CFG(Configure) and SIB3 contains
threshServingLowQ (set by CellResel.ThrshServLowQ), a UE reselects to a higher-priority
inter-frequency or inter-RAT neighboring cell when all the following conditions are met:
l The UE has camped on the serving cell for more than 1 second.
l The neighboring cell has one of the following measurement results:
Neighboring E-UTRAN cell: The Squal values of measured neighboring cells are
greater than the value of threshX-HighQ (configured in the
EutranInterNFreq.ThreshXHighQ parameter) broadcast in SIB5 within the inter-
frequency neighboring cell reselection time (configured in the
EutranInterNFreq.EutranReselTime parameter) broadcast in SIB5. For details
about how to calculate the Squal values, see 3.2.6 Intra-Frequency or Equal-
Priority Inter-Frequency Cell Reselection.
Neighboring UTRAN FDD cell: The Squal values of measured neighboring cells
are greater than the value of threshX-HighQ (configured in the
UtranNFreq.ThreshXHighQ parameter) broadcast in SIB6 within the neighboring
UTRAN cell reselection time (configured in the CellReselUtran.TreselUtran
parameter) broadcast in SIB6.
Neighboring UTRAN TDD cell: The Srxlev values of measured neighboring cells
are greater than the value of threshX-High (configured in the
UtranNFreq.ThreshXHigh parameter) broadcast in SIB6 within the neighboring
UTRAN cell reselection time (configured in the CellReselUtran.TreselUtran
parameter) broadcast in SIB6.
Neighboring GERAN cell: The Srxlev values of measured neighboring cells are
greater than the value of threshX-High (configured in the
GeranNfreqGroup.ThreshXHigh parameter) broadcast in SIB7 within the
neighboring GERAN cell reselection time (configured in the
CellReselGeran.TReselGeran parameter) broadcast in SIB7.
Neighboring CDMA2000 cell: The Srxlev values of measured neighboring cells are
greater than the value of threshX-High (configured in the
Cdma2000BandClass.Cdma20001XrttThreshXHigh and
Cdma2000BandClass.Cdma2000HrpdThreshXHigh parameters) broadcast in
SIB8 within the neighboring CDMA2000 cell reselection time (configured in the
CellReselCdma2000.Cdma1XrttTreselection and
CellReselCdma2000.TreselectionHrpd parameters) broadcast in SIB8.
If CellResel.ThrshServLowQCfgInd is set to NOT_CFG(Not configure) and SIB3 does not
contain threshServingLowQ, a UE reselects to a higher-priority inter-frequency or inter-RAT
neighboring cell when all of the following conditions are met:

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 22


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

l The UE has camped on the serving cell for more than 1 second.
l The neighboring cell has one of the following measurement results:
Neighboring E-UTRAN cell: The Srxlev values of measured neighboring cells are
greater than the value of threshX-High (configured in the
EutranInterNFreq.ThreshXhigh parameter) broadcast in SIB5 within the inter-
frequency neighboring cell reselection time (configured in the
EutranInterNFreq.EutranReselTime parameter) broadcast in SIB5. For details
about how to calculate the Srxlev values, see 3.2.6 Intra-Frequency or Equal-
Priority Inter-Frequency Cell Reselection.
Neighboring UTRAN cell: The Srxlev values of measured neighboring cells are
greater than the value of threshX-High (configured in the
UtranNFreq.ThreshXHigh parameter) broadcast in SIB6 within the neighboring
UTRAN cell reselection time (configured in the CellReselUtran.TreselUtran
parameter) broadcast in SIB6.
Neighboring GERAN cell: The Srxlev values of measured neighboring cells are
greater than the value of threshX-High (configured in the
GeranNfreqGroup.ThreshXHigh parameter) broadcast in SIB7 within the
neighboring GERAN cell reselection time (configured in the
CellReselGeran.TReselGeran parameter) broadcast in SIB7.
Neighboring CDMA2000 cell: The Srxlev values of measured neighboring cells are
greater than the value of threshX-High (configured in the
Cdma2000BandClass.Cdma20001XrttThreshXHigh and
Cdma2000BandClass.Cdma2000HrpdThreshXHigh parameters) broadcast in
SIB8 within the neighboring CDMA2000 cell reselection time (configured in the
CellReselCdma2000.Cdma1XrttTreselection and
CellReselCdma2000.TreselectionHrpd parameters) broadcast in SIB8.
If the highest ranked cell is unsuitable for a UE because it is included in a roaming-forbidden
TA or because it does not belong to the RPLMN or an EPLMN, the UE does not consider this
cell as a candidate for reselection within 300 seconds.

Reselection to a Lower-Priority Cell


If CellResel.ThrshServLowQCfgInd is set to CFG(Configure) and SIB3 contains
threshServingLowQ (set by CellResel.ThrshServLowQ), a UE reselects to a lower-priority
inter-frequency or inter-RAT neighboring cell when all the following conditions are met:
l No higher-priority inter-frequency or inter-RAT neighboring cell meets the cell
reselection criteria.
l The UE has camped on the serving cell for more than 1 second.
l The neighboring cell has one of the following measurement results:
NOTE

For details about how to calculate the Squal value of the serving cell, see Cell Selection Criteria.
Neighboring E-UTRAN cell: The Squal value of the serving cell is less than the
value of threshServingLowQ broadcast in SIB3 and the Squal values of measured
neighboring cells are greater than the value of threshX-LowQ (configured in the
EutranInterNFreq.ThreshXlowQ parameter) broadcast in SIB5 within the inter-
frequency neighboring cell reselection time (configured in the
EutranInterNFreq.EutranReselTime parameter) broadcast in SIB5. For details
about how to calculate the Squal values of the measured neighboring cells, see 3.2.6
Intra-Frequency or Equal-Priority Inter-Frequency Cell Reselection.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 23


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

Neighboring UTRAN FDD cell: The Squal value of the serving cell is less than the
value of threshServingLowQ broadcast in SIB3 and the Squal values of measured
neighboring cells are greater than the value of threshX-LowQ (configured in the
UtranNFreq.ThreshXLowQ parameter) broadcast in SIB6 within the neighboring
UTRAN cell reselection time (configured in the CellReselUtran.TreselUtran
parameter) broadcast in SIB6.
Neighboring UTRAN TDD cell: The Squal value of the serving cell is less than the
value of threshServingLowQ broadcast in SIB3 and the Squal values of measured
neighboring cells are greater than the value of threshX-Low (configured in the
UtranNFreq.ThreshXLow parameter) broadcast in SIB6 within the neighboring
UTRAN cell reselection time (configured in the CellReselUtran.TreselUtran
parameter) broadcast in SIB6.
Neighboring GERAN cell: The Squal value of the serving cell is less than the value
of threshServingLowQ broadcast in SIB3 and the Srxlev values of measured
neighboring cells are greater than the value of threshX-Low (configured in the
GeranNfreqGroup.ThreshXlow parameter) broadcast in SIB7 within the
neighboring GERAN cell reselection time (configured in the
CellReselGeran.TReselGeran parameter) broadcast in SIB7.
Neighboring CDMA2000 cell: The Squal value of the serving cell is less than the
value of threshServingLowQ broadcast in SIB3 and the Srxlev values of measured
neighboring cells are greater than the value of threshX-Low (configured in the
Cdma2000BandClass.Cdma20001XrttThreshXLow and
Cdma2000BandClass.Cdma2000HrpdThreshXLow parameters) broadcast in
SIB8 within the neighboring CDMA2000 cell reselection time (configured in the
CellReselCdma2000.Cdma1XrttTreselection and
CellReselCdma2000.TreselectionHrpd parameters) broadcast in SIB8.
If CellResel.ThrshServLowQCfgInd is set to NOT_CFG(Not configure) and SIB3 does not
contain threshServingLowQ, a UE reselects to a lower-priority inter-frequency or inter-RAT
neighboring cell when all the following conditions are met:
l No higher-priority inter-frequency or inter-RAT neighboring cell meets the cell
reselection criteria.
l The UE has camped on the serving cell for more than 1 second.
l The neighboring cell has one of the following measurement results:
NOTE

For details about how to calculate the Srxlev value of the serving cell, see Cell Selection Criteria.
Neighboring E-UTRAN cell: The Srxlev value of the serving cell is less than the
value of threshServingLow (configured in the CellResel.ThrshServLow parameter)
broadcast in SIB3 and the Srxlev values of measured neighboring cells are greater
than the value of threshX-Low (configured in the EutranInterNFreq.ThreshXlow
parameter) broadcast in SIB5 within the inter-frequency neighboring cell
reselection time (configured in the EutranInterNFreq.EutranReselTime
parameter) broadcast in SIB5. For details about how to calculate the Srxlev values
of the measured neighboring cells, see 3.2.6 Intra-Frequency or Equal-Priority
Inter-Frequency Cell Reselection.
Neighboring UTRAN cell: The Srxlev value of the serving cell is less than the
value of threshServingLow (configured in the CellResel.ThrshServLow parameter)
broadcast in SIB3 and the Srxlev values of measured neighboring cells are greater
than the value of threshX-Low (configured in the UtranNFreq.ThreshXLow
parameter) broadcast in SIB6 within the neighboring UTRAN cell reselection time
(configured in the CellReselUtran.TreselUtran parameter) broadcast in SIB6.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 24


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

Neighboring GERAN cell: The Srxlev value of the serving cell is less than the
value of threshServingLow (configured in the CellResel.ThrshServLow parameter)
broadcast in SIB3 and the Srxlev values of measured neighboring cells are greater
than the value of threshX-Low (configured in the GeranNfreqGroup.ThreshXLow
parameter) broadcast in SIB7 within the neighboring GERAN cell reselection time
(configured in the CellReselGeran.TReselGeran parameter) broadcast in SIB7.
Neighboring CDMA2000 cell: The Srxlev value of the serving cell is less than the
value of threshServingLow (configured in the CellResel.ThrshServLow parameter)
broadcast in SIB3 and the Srxlev values of measured neighboring cells are greater
than the value of threshX-Low (configured in the
Cdma2000BandClass.Cdma20001XrttThreshXLow and
Cdma2000BandClass.Cdma2000HrpdThreshXLow parameters) broadcast in
SIB8 within the neighboring CDMA2000 cell reselection time (configured in the
CellReselCdma2000.Cdma1XrttTreselection and
CellReselCdma2000.TreselectionHrpd parameters) broadcast in SIB8.

3.2.8 Speed-based Cell Reselection


UE movement is classified, by speed, as either normal-, medium-, or high-speed. A UE may
start at a normal speed and then accelerate. When the UE is moving at medium or high speed,
it quickly reselects to a cell. In such a case, related cell reselection parameters must be
adjusted accordingly. Speed-based cell reselection is supported only when cell reselection for
UEs at normal speed has been enabled.
Speed-based cell reselection is enabled by setting CellResel.SpeedDepReselCfgInd to
CFG(Configure) and a specific neighboring cell parameter to CFG(Configure). Table 3-1
lists the parameters for various neighboring cells.

Table 3-1 Neighboring cell parameters


Neighboring Cell Type Parameter

Intra-frequency neighboring E-UTRAN cell CellResel.SpeedStateSfCfgInd

Inter-frequency neighboring E-UTRAN cell EutranInterNFreq.SpeedDependSPCf-


gInd

Neighboring UTRAN cell CellReselUtran.SpeedStateSfCfgInd

Neighboring GERAN cell CellReselGeran.SpeedStateSfCfgInd

Neighboring CDMA2000 HRPD cell CellReselCdma2000.SpeedStateSfCfgInd

Neighboring CDMA2000 1XRTT cell CellReselCdma2000.Cdma1XrttSpeedStat


eCfgInd

A UE determines its speed based on the system information broadcast by the eNodeB. The
details are as follows:
l If the number of reselection cells does not exceed n-CellChangeMedium (configured in
the CellResel.NCellChangeMedium parameter) or n-CellChangeHigh (configured in the
CellResel.NCellChangeHigh parameter) within the t-Evaluation duration (configured in
the CellResel.TEvaluation parameter) and the number of reselection cells does not
exceed n-CellChangeMedium or n-CellChangeHigh during the subsequent t-HystNormal

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 25


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

duration (configured in the CellResel.THystNormal parameter), the UE is a normal-


speed UE.
l A UE determines that it is moving at a medium speed when the number of reselected
cells is greater than n-CellChangeMedium but less than or equal to n-CellChangeHigh
within the t-Evaluation period.
l A UE determines that it is moving at a high speed when the number of reselected cells is
greater than n- CellChangeHigh within the t-Evaluation period.
NOTE

If a UE repeatedly selects a cell, the cell is counted only once into the number of reselected cells.

Cell reselection time and hysteresis vary with the UE speed. The details are as follows:
l Table 3-2 describes cell reselection time required by normal-speed UEs.
l Table 3-3 describes cell reselection time required by medium-speed UEs.
l Table 3-4 describes cell reselection time required by high-speed UEs.
l Table 3-5 describes the reselection hysteresis for the UE at a specific speed.

Table 3-2 Cell reselection time required by normal-speed UEs.


Neighbori Syste Cell Reselection Parameter
ng Cell m Time
Type Infor
matio
n
Involv
ed

Intra- SIB3 t- t-ReselectionEUTRA is specified by


frequency ReselectionEUTR CellResel.TreselEutran.
neighborin A
g E-
UTRAN
cell

Inter- SIB5 t- t-ReselectionEUTRA is specified by


frequency ReselectionEUTR EutranInterNFreq.EutranReselTime.
neighborin A
g E-
UTRAN
cell

Neighborin SIB6 t- t-ReselectionUTRA is specified by


g UTRAN ReselectionUTRA CellReselUtran.TReselUtran.
cell

Neighborin SIB7 t- t-ReselectionGERAN is specified by


g GERAN ReselectionGERA CellReselGeran.TReselGeran.
cell N

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 26


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

Neighbori Syste Cell Reselection Parameter


ng Cell m Time
Type Infor
matio
n
Involv
ed

Neighborin SIB8 parametersHRPD.t- parametersHRPD.t-ReselectionCDMA2000


g ReselectionCDMA is specified by
CDMA200 2000 CellReselCdma2000.TreselectionHrpd.
0 HRPD
cell

Neighborin SIB8 parameters1XRTT.t parameters1XRTT.t-


g - ReselectionCDMA2000 is specified by
CDMA200 ReselectionCDMA CellReselCdma2000.Cdma1XrttTreselecti
0 1XRTT 2000 on.
cell

Table 3-3 Cell reselection time required by medium-speed UEs


Neighbor System Cell Reselection Parameter
ing Cell Inform Time
Type ation
Involv
ed

Intra- SIB3 t-ReselectionEUTRA x l t-ReselectionEUTRA is specified by


frequency t-ReselectionEUTRA- CellResel.TreselEutran.
neighborin SF.sf-Medium l t-ReselectionEUTRA-SF.sf-Medium
g E- is specified by
UTRAN CellResel.TReselEutranSfMedium.
cell

Inter- SIB5 t-ReselectionEUTRA x l t-ReselectionEUTRA is specified by


frequency t-ReselectionEUTRA- EutranInterNFreq.EutranReselTi
neighborin SF.sf-Medium me.
g E- l t-ReselectionEUTRA-SF.sf-Medium
UTRAN is specified by
cell EutranInterNFreq.TReselEutranS
fMedium.

Neighborin SIB6 t-ReselectionUTRA x t- l t-ReselectionUTRA is specified by


g UTRAN ReselectionUTRA- CellReselUtran.TReselUtran.
cell SF.sf-Medium l t-ReselectionUTRA-SF.sf-Medium
is specified by
CellReselUtran.TReselUtranSfMe-
dium.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 27


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

Neighbor System Cell Reselection Parameter


ing Cell Inform Time
Type ation
Involv
ed

Neighborin SIB7 t-ReselectionGERAN x l t-ReselectionGERAN is specified by


g GERAN t-ReselectionGERAN- CellReselGeran.TReselGeran.
cell SF.sf-Medium l t-ReselectionGERAN-SF.sf-Medium
is specified by
CellReselGeran.TReselGeranSfMe
dium.

Neighborin SIB8 parametersHRPD.t- l parametersHRPD.t-


g ReselectionCDMA200 ReselectionCDMA2000 is specified
CDMA200 0 x parametersHRPD.t- by
0 HRPD ReselectionCDMA200 CellReselCdma2000.TreselectionH
cell 0-SF.sf-Medium rpd.
l parametersHRPD.t-
ReselectionCDMA2000-SF.sf-
Medium is specified by
CellReselCdma2000.TReselCdma
HrpdSfMedium.

Neighborin SIB8 parameters1XRTT.t- l parameters1XRTT.t-


g ReselectionCDMA200 ReselectionCDMA2000 is specified
CDMA200 0x by
0 1XRTT parameters1XRTT.t- CellReselCdma2000.Cdma1XrttTr
cell ReselectionCDMA200 eselection.
0-SF.sf-Medium l parameters1XRTT.t-
ReselectionCDMA2000-SF.sf-
Medium is specified by
CellReselCdma2000.Cdma1XrttSf
Medium.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 28


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

Table 3-4 Cell reselection time required by high-speed UEs


Neighbori Syste Cell Reselection Time Parameter
ng Cell m
Type Infor
matio
n
Involv
ed

Intra- SIB3 t-ReselectionEUTRA x t- l t-ReselectionEUTRA is specified


frequency ReselectionEUTRA- by CellResel.TreselEutran.
neighborin SF.sf-High l t-ReselectionEUTRA-SF.sf-High
g E- is specified by
UTRAN CellResel.TReselEutranSfHigh.
cell

Inter- SIB5 t-ReselectionEUTRA x t- l t-ReselectionEUTRA is specified


frequency ReselectionEUTRA- by
neighborin SF.sf-High EutranInterNFreq.EutranReselT
g E- ime.
UTRAN l t-ReselectionEUTRA-SF.sf-High
cell is specified by
EutranInterNFreq.TReselEutran
SfHigh.

Neighborin SIB6 t-ReselectionUTRA x t- l t-ReselectionUTRA is specified by


g UTRAN ReselectionUTRA-SF.sf- CellReselUtran.TReselUtran.
cell High l t-ReselectionUTRA-SF.sf-High is
specified by
CellReselUtran.TReselUtranSfHi
gh.

Neighborin SIB7 t-ReselectionGERAN x l t-ReselectionGERAN is specified


g GERAN t-ReselectionGERAN- by CellReselGeran.TReselGeran.
cell SF.sf-High l t-ReselectionGERAN-SF.sf-High
is specified by
CellReselGeran.TReselGeranSfH
igh.

Neighborin SIB8 parametersHRPD.t- l parametersHRPD.t-


g ReselectionCDMA2000 ReselectionCDMA2000 is
CDMA200 x parametersHRPD.t- specified by
0 HRPD ReselectionCDMA2000- CellReselCdma2000.Treselection
cell SF.sf-High Hrpd.
l parametersHRPD.t-
ReselectionCDMA2000-SF.sf-
High is specified by
CellReselCdma2000.TReselCdm
aHrpdSfHigh.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 29


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

Neighbori Syste Cell Reselection Time Parameter


ng Cell m
Type Infor
matio
n
Involv
ed

Neighborin SIB8 parameters1XRTT.t- l parameters1XRTT.t-


g ReselectionCDMA2000 ReselectionCDMA2000 is
CDMA200 * parameters1XRTT.t- specified by
0 1XRTT ReselectionCDMA2000- CellReselCdma2000.Cdma1XrttT
cell SF.sf-High reselection.
l parameters1XRTT.t-
ReselectionCDMA2000-SF.sf-
High is specified by
CellReselCdma2000.Cdma1XrttS
fHigh.

Table 3-5 Cell reselection hysteresis


UE Speed System Cell reselection Parameter
Inform hysteresis
ation
Involve
d

Normal-speed SIB3 q-Hyst q-Hyst is specified by


UE CellResel.Qhyst.

Medium-speed SIB3 q-Hyst + q- l q-Hyst is specified by


UE HystSF.sf-Medium CellResel.Qhyst.
l q-HystSF.sf-Medium is specified
by CellResel.QHystSfMedium.

High-speed SIB3 q-Hyst + q- l q-Hyst is specified by


UE HystSF.sf-High CellResel.Qhyst.
l q-HystSF.sf-High is specified by
CellResel.QHystSfHigh.

3.3 Tracking Area Registration


UEs register their locations with the evolved packet core (EPC) through a TA registration
procedure so that the EPC can page them within the TA and request that they initiate services.
The TA is a concept introduced to the LTE/SAE system for location management of UEs. A
TA is identified by a tracking area identity (TAI), which consists of the MCC, MNC, and
tracking area code (TAC).
TA registration can be performed in two ways: tracking area update (TAU) and Attach/
Detach.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 30


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

3.3.1 Tracking Area Update


A UE performs TA updates in the following situations. That is, the UE sends a TA update
request when any of the following conditions is met (For details, see section 5.3.3.0
"Provision of UE's TAI to MME in ECM-CONNECTED state" in 3GPP TS 23.401 R10,
which was released in March 2011):

l The UE detects that it has entered a new TA when it finds that the TAI in the system
information is different from any TAI stored in its USIM.
l The periodic TA update timer expires. This timer length is delivered to the UE through a
non-access stratum (NAS) message.
l The UE performs an inter-RAT cell reselection to an E-UTRAN cell.
l The RRC connection is released with the release cause "load re-balancing TAU
required".
l The information on UE capabilities stored in the EPC changes.
l The information on Discontinuous Reception (DRX) parameters changes. For details, see
3.6 Paging.

The UE informs the EPC of its TA by TA update. The EPC will send paging messages to all
eNodeBs in the TA.

3.3.2 Attach/Detach
When a UE needs to obtain services from a network but is not registered to the network, the
UE performs an Attach procedure for TA registration. For the detailed Attach procedure, see
section 5.3.2.1 "E-UTRAN Initial Attach" in 3GPP TS 23.401 R10, which was released in
March 2011.

After a successful Attach procedure, the UE is assigned an IP address. The Mobile Equipment
Identity (MEI) of the UE will be sent to the Mobility Management Entity (MME) for
authentication.

When the UE fails to access the EPC or the EPC does not allow the access of the UE, a
Detach procedure is initiated. After the Detach procedure, the EPC no longer pages the UE.

3.4 Cell Reservation and Access Control


Cell reservation and access control are two mechanisms operators use to control their
networks. Cell reservation allows specific cells to be reserved for only UEs of certain access
classes (for example, for network management by operators). Access control determines
whether UEs can initiate calls in a cell based on UE classes.

l The cell reservation mechanism controls cell selection and reselection procedures. Cells
can be reserved only for UEs in idle mode.
l The access control mechanism is implemented for UEs on the basis of access classes. To
implement access control, one or more access classes are allocated to a UE and stored on
the USIM, but access class 10 is signaled to the UE through system information.

3.4.1 Cell Reservation and Barring


UEs are notified of cell status by the following information in SIB1:

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 31


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

l cellBarred: specifies whether a cell is barred. The cell barred status is set by
CELLACCESS.CellBarred. If a cell belongs to multiple PLMNs, the cell barred status
is shared by all the PLMNs.
l cellReservedForOperatorUse: specifies whether a cell is reserved. The cell reserved
status is set by CELLOP.CellReservedForOp. Each PLMN has its own reserved status.

Table 3-6 describes cell type, and respective selection and reselection principles.

Table 3-6 Selection and reselection principles for reserved and barred cells
Cell Type Cell Selection and Reselection Principle

Unbarred and The UE can consider this cell a candidate during cell selection and
unreserved for reselection procedures.
operator use

Unbarred but During cell selection and reselection procedures:


reserved for l If UEs of access class 11 or 15 camp on their HPLMNs or on
operator use EHPLMNs, the UEs treat this cell as a candidate cell.
l Otherwise, UEs treat this cell as a barred cell.

Barred cell During cell selection and reselection procedures:


l The UEs cannot select or reselect to this cell, not even for emergency
calls.
l The UEs select another cell as follows:
When intraFreqReselection (set by the
CELLACCESS.IntraFreqResel parameter) in SIB1 indicates that
intra-frequency reselection is allowed, the UEs may select another
cell on the same frequency if reselection criteria are fulfilled.
When CELLACCESS.IntraFreqResel in SIB1 indicates that
intra-frequency reselection is not allowed, the UEs do not reselect
a cell on the same frequency as the barred cell. The value of
intraFreqReselection in SIB1 is specified by the
CELLACCESS.IntraFreqResel parameter.
The UEs exclude the barred cell as a candidate for cell selection or
reselection for 300 seconds.

3.4.2 Access Control


Access classes are applicable to UE access over the Uu interface. There are 16 access classes,
numbered from 0 to 15. The information about access classes 0 to 9 and 11 to 15 is stored in
USIMs, and the information about access class 10 is signaled to UEs through system
information broadcast to indicate whether cells allow emergency calls. For details about the
list of barred access classes and how UEs determine their access classes, see chapter 4
"Access control" in 3GPP TS 22.011 V10.0.0 and section 3.4 "Access control" in 3GPP TS
23.122 V10.0.0.

The access class control method is used to control UE network access, as defined in 3GPP TS
36.331. For details about Huawei access control, see Access Class Control Feature Parameter
Description.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 32


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

3.5 System Information Broadcast


This section describes the basic feature LBFD-002009 Broadcast of system information.
During system information broadcast, information such as parameters related to cell selection
and reselection, is broadcast to UEs over the broadcast control channel (BCCH).
System Information (SI) messages are categorized, based on their contents, into one master
information block (MIB) and multiple system information blocks (SIBs). The number of SIBs
is specified in the latest 3GPP protocols. SI messages are transmitted over the BCCH. Figure
3-4 shows the relationships between the MIB and the SIBs.
The MIB is transmitted over the BCH through an independent RRC message. The scheduling
period of the MIB is always 40 ms. The BCH is predefined by transport format. Therefore,
the UE receives the MIB on the BCH without obtaining other information on the network.
SIB1 is transmitted over the downlink shared channel (DL-SCH) through an independent
RRC message. The scheduling period of SIB1 is always 80 ms. Other SIBs are transmitted
over the DL-SCH through SI messages, and their scheduling periods can be separately set.
The SIBs with the same scheduling period can be transmitted through the same SI message,
and one SIB can be contained in only one SI message. SIB1 carries the scheduling period
information of all the SIBs and the mapping between SIBs and SI messages. SIB2 must be
mapped to the SI message that corresponds to the first entry in the list of SI messages in the
scheduling information. On the physical dedicated control channel (PDCCH), the UE obtains
time and frequency data for the SIB by parsing the SI-Radio Network Temporary Identifier
(SI-RNTI).
Only SIB6 and SIB7 delivery is under switch control:
l SIB6 is broadcast only when CellSiMap.SiSwitch(Sib6Switch) is turned on and the
CELLRESELUTRAN MO has been configured.
l SIB7 is broadcast only when CellSiMap.SiSwitch(Sib7Switch) is turned on and the
CELLRESELGERAN MO has been configured.
l When the contents of the SI are changed, the eNodeB sends paging messages to instruct
the UE in idle mode and UE in connected mode to read the new SI messages.

Figure 3-4 Relationships between SI messages

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 33


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

3.5.1 System Information Block Contents


The MIB and each SIB contain different information. Table 3-7 lists the main contents of the
MIB and each SIB. For details, see sections 6.2.2 "Message definitions" and 6.3.1 "System
information blocks" in 3GPP TS 36.331 R10, which was released in March 2011.

Table 3-7 Contents of the MIB and SIBs


SI Block Content

MIB Downlink bandwidth of a cell, Physical HARQ


Indication Channel (PHICH) parameters, and System
Frame Number (SFN)

SIB1 Parameters related to cell access and cell selection and


scheduling information of SI messages

SIB2 Common radio parameters used by all the UEs in a cell

SIB3 Common cell reselection parameters for all the cells


and intra-frequency cell reselection parameters

SIB4 Intra-frequency neighboring cell list, reselection


parameters of each neighboring cell used for cell
reselection, and intra-frequency cell reselection
blacklist

SIB5 Non-serving E-UTRA frequency list and reselection


parameters of each frequency used for cell reselection
Inter-frequency neighboring cell list and reselection
parameters of each neighboring cell used for cell
reselection
Inter-frequency cell reselection blacklist

SIB6 Universal Terrestrial Radio Access (UTRA) frequency


division duplex (FDD) neighboring frequency list and
reselection parameters of each frequency used for cell
reselection
UTRA time division duplex (TDD) neighboring
frequency list and reselection parameters of each
frequency used for cell reselection

SIB7 GERAN neighboring frequency list and reselection


parameters of each frequency used for cell reselection

SIB8 CDMA2000 pre-registration information


CDMA2000 neighboring frequency band list and
reselection parameters of each band used for cell
reselection
CDMA2000 neighboring cell list of neighboring
frequency band

SIB9 Name of the home eNodeB

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 34


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

SI Block Content

SIB10 Earthquake and Tsunami Warning System (ETWS)


primary notification

SIB11 ETWS secondary notification

SIB12 CMAS notification

SIB13 MBMS control information

SIB14 Extended Access Barring (EAB) parameters

SIB15 MBMS Service Area Identities (SAI)

SIB16 GPS time and Coordinated Universal Time (UTC)

3.5.2 System Information Scheduling Periods


The scheduling period for the MIB is fixed at 40 ms. The first transmission of the MIB is
scheduled in subframe 0 of radio frames for which the SFN mod 4 = 0, and repetitions are
scheduled in subframe 0 of the last three radio frames in each period.

The scheduling period for the SIB1 is fixed at 80 ms. The first transmission of the SIB1 is
scheduled in subframe 5 of radio frames for which the SFN mod 8 = 0, and repetitions are
scheduled in subframe 5 of the later radio frames for which SFN mod 2 = 0 in each period.

The scheduling periods for other SIBs are specified by CellSiMap.SibxPeriod (x indicates 2,
3...). The mapping between an SIB and the SI is affected by the scheduling period of the SIB,
number of SIBs, and bandwidth resources. The SIBs with the same scheduling period map
onto the same SI. However, the number of SIBs that can map onto the same SI is limited. The
eNodeB must take into account the minimum UE capability to ensure that all the UEs in a cell
can read the system information.

An SI message can be transmitted only within a specific duration in the scheduling period,
and the specific duration is called SI window. Only one type of SI message can be transmitted
in an SI window. Within the SI window, the corresponding SI message can be transmitted a
number of times in any subframe other than multimedia broadcast multicast service single
frequency network (MBSFN) subframes, uplink subframes in TDD, and the subframes in
which the SIB1 is transmitted. The length of the SI window is determined by the system. For
details about the scheduling of the SI, see section 5.2 "System information" in 3GPP TS
36.331 R10, which was released in March 2011.

3.5.3 System Information Update


A UE reads SI messages in the following scenarios:

l The UE has been powered on and is selecting a cell to camp on.


l The UE is performing cell reselection.
l The UE has performed a handover.
l The UE is entering E-UTRAN from another system.
l The UE is returning from an area with no coverage.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 35


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

After obtaining the SI message, the UE does not repeatedly read the message. It rereads and
updates the SI message only when any of the following conditions is met:

l The UE receives the SI message change notification in the paging message transmitted
from the eNodeB.
l The UE receives the ETWS or CMAS message broadcast notification in the paging
message transmitted from the eNodeB.
l When the UE receives an SI message, it has been 3 hours since it received the previous
SI message.

When receiving the SI message change notification in the paging message, the UE does not
immediately update the SI message. Instead, it receives the SI message updated by the
eNodeB in the next message modification period. For details about the SI message update, see
section 5.2 "System information" in 3GPP TS 36.331 R10, which was released in March
2011.

Figure 3-5 shows the SI message update procedure. The modification period of the SI
message is N radio frames, starting from a radio frame for which SFN mod n = 0. During
modification period number n, the eNodeB transmits the paging message to inform UEs in
RRC_IDLE mode and UEs in RRC_CONNECTED mode about the SI message change when
a paging cycle arrives. When the n+1 modification period arrives, the eNodeB transmits the
updated SI message. In this figure, different colors indicate SI messages with different
contents.

Figure 3-5 SI message update procedure

where

l The length of the SI modification period (N radio frames) = modificationPeriodCoeff x


defaultPagingCycle, where modificationPeriodCoeff and defaultPagingCycle are
broadcast in SIB2.
modificationPeriodCoeff is the coefficient of the modification period, indicating the
minimum number of times the UE monitors paging messages within the SI message
modification period. It is set by the BcchCfg.ModifyPeriodCoeff parameter.
defaultPagingCycle is the default paging cycle in units of radio frames. It is set by
the PCCHCfg.DefaultPagingCycle parameter.
l During eNodeB notification update, the length of the paging message delivery is
controlled by CellSiMap.SibUpdOptSwitch.
When CellSiMap.SibUpdOptSwitch is set to SibPagingOptCtrlSwitch, that is, the
switch is turned on (default setting: turned off), the length is equal to the length of
the SI modification period.
When the switch is turned off (default setting), the length is occasionally shorter
than the length of the SI modification period.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 36


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

When SI messages (except SIB10, SIB11, SIB12, and SIB14) are updated, the eNodeB
changes systemInfoValueTag in SIB1. The UE reads the value and compares it with the one it
read last time. If the value has changed, it is an indication that the SI message has changed. If
the value has not changed, it is an indication that the SI message has not changed.
If SIB10, SIB11, SIB12, or SIB14 has changed, the eNodeB does not change
systemInfoValueTag in SIB1. Instead, the eNodeB delivers paging messages to the UE,
notifying that the ETWS message and commercial mobile alert system (CMAS) have
changed.
For the CDMA2000 system time changes in SIB8 and the UTC time changes in SIB16, the
eNodeB does not change systemInfoValueTag in SIB1 or notify the UE of the SI message
change in paging messages.
The UE reads the SI message again 3 hours after receiving an SI message. In this case, the UE
reads all the SI messages regardless of whether systemInfoValueTag has changed.

3.6 Paging
This section describes the basic feature LBFD-002011 Paging.
In paging, paging messages are used to inform all the UEs in a given cell of any changes in
system information, and to carry information of UEs being paged.

3.6.1 Triggering of Paging


Paging is a procedure of transmitting paging messages to UEs in RRC_IDLE mode or
informing all UEs in RRC_CONNECTED mode and RRC_IDLE mode about an SI message
change. A paging procedure can be initiated by either an MME or an eNodeB.
When an MME initiates a paging procedure, the paging message contains a tracking area list
(TAL) for the concerned UE. In all the cells within the TAs on the list, the eNodeBs transmit
the paging message over the paging control channel (PCCH) to page the UE. To increase the
probability that the UE successfully receives the message, the eNodeBs send the paging
message over the radio interface a number of times specified by the
PCCHCfg.PagingSentNum parameter. The paging message contains the domain information
and UE identity. The domain information indicates the origin of paging, and the UE identity
may be the S-temporary mobile subscriber identity (S-TMSI) or international mobile
subscriber identity (IMSI) of the UE.
When the SI message changes, the eNodeB transmits a paging message to notify all UEs in
RRC_CONNECTED mode and RRC_IDLE mode in the cell and transmits the updated SI
message in the next SI message modification period. To ensure that all of these UEs receive
the system information, the eNodeB transmits the paging message on all possible occasions in
discontinuous reception (DRX) cycles.
Though paging is triggered from different Network Elements (NEs), the paging mechanism
on the Uu interface is the same.

3.6.2 Paging Mechanism over the Uu Interface


UEs in idle mode receive paging messages using DRX to reduce power consumption. The
frames that paging messages are transmitted on over the Uu interface are fixed. These frames
are indicated by the paging frames (PFs) and paging occasion (PO) subframes. One PF is one
radio frame, which may contain one or multiple POs, as shown in Figure 3-6. One PO is a

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 37


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

subframe where the paging radio network temporary identifier (P-RNTI) is contained. The PO
is transmitted over the PDCCH. In accordance with 3GPP specifications, the P-RNTI value is
fixed. UEs read paging messages over the physical downlink shared channel (PDSCH)
according to the P-RNTI.

Figure 3-6 Paging mechanism

The PF number and PO subframe number can be calculated based on the IMSI of the UE,
DRX cycle, and number of PO subframes within a DRX cycle. Frame numbers are stored in
the SI that contains the DRX parameters of the UE. The PF number and PO subframe number
change with the DRX parameters.

The SFN of a PF is calculated as follows: SFN mod T = (T div N) x (UE_ID mod N)

The subframe number i_s of a PO in FDD is listed in Table 3-8. The subframe number i_s of
a PO is derived from the following formula: i_s = floor (UE_ID/N) mod Ns, where floor
represents rounding (UE_ID/N) down to the nearest integer.

Table 3-8 Subframe number i_s of a PO in FDD

Ns PO when i_s=0 PO when i_s=1 PO when i_s=2 PO when i_s=3

1 9 N/A N/A N/A

2 4 9 N/A N/A

4 0 4 5 9

The variables in these formulas are as follows:


l T: DRX cycle. The UE, eNodeB, and MME calculate their own DRX cycles as follows:

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 38


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

Calculation of DRX cycles by the UE


(1) When a UE specific paging cycle is not used, the UE uses the
defaultPagingCycle IE value broadcast in SIB2 by the eNodeB as its DRX cycle.
The defaultPagingCycle IE value is specified by the
PCCHCfg.DefaultPagingCycle parameter.
(2) When the UE specific paging cycle is used, the UE notifies the MME of the
paging cycle length using NAS messages. In addition, the UE compares the UE
specific paging cycle length with the defaultPagingCycle IE value and uses the
smaller one as its DRX cycle.
Calculation of DRX cycles by the eNodeB
(1) If the MME has specified a paging DRX cycle in a paging message, the eNodeB
compares the paging DRX cycle length with the DefaultPagingCycle IE value, and
uses the smaller one as the paging DRX cycle.
(2) If the MME does not specify a paging DRX cycle in a paging message, the
eNodeB uses the defaultPagingCycle IE value as the paging DRX cycle.
Calculation of DRX cycles by the MME
If the UE specific paging cycle is used, the MME specifies the paging DRX cycle
(the UE specific paging cycle) in a paging message to the eNodeB. If the UE
specific paging cycle is not used, the MME sends the eNodeB a paging message
without containing the paging DRX cycle.
NOTE

l According to section 5.13 in 3GPP TS 23.401 R11 released in December, 2013, the MME is
only supposed to specify a paging DRX cycle in a paging message to the eNodeB when the
UE specific paging cycle is being used. In this situation, the paging DRX cycle is equal to the
UE specific paging cycle. Otherwise, the MME does not include a paging DRX cycle in the
paging message.
l In the S1 setup process, the eNodeB sends the MME the eNodeB-specific default paging DRX
cycle (specified by the GlobalProcSwitch.S1DefaultPagingDrxSelect parameter) for the
MME to determine the paging response timeout length. However, not all MMEs comply with
3GPP specifications. Even when the UE specific paging cycle is not used, these non-compliant
MMEs specify a paging DRX cycle, equal to the default paging DRX cycle reported by the
eNodeB over the S1 interface, in a paging message to the eNodeB. In this case, if the default
paging DRX cycle is less than the value of the defaultPagingCycle IE value, the DRX cycle
length calculated by the eNodeB differs from that calculated by the UE. To prevent this
problem, it is recommended that the length of the default paging DRX cycle be greater than or
equal to the defaultPagingCycle IE value.
l N is min(T, nB). The PCCHCfg.Nb parameter specifies nB. It can be set to 4T, 2T, T,
T/2, T/4, T/8, T/16, or T/32.
l Ns is max(1,nB/T).
l UE_ID: equal to IMSI mod1024. If a UE without an IMSI makes an emergency call, the
UE uses the default UE_ID value of 0.
If paging is triggered by the MME, the UE_ID value is the UE identity index value
contained in the paging message sent over the S1 interface.
If paging is triggered by the eNodeB and no UE_ID is available, the UE uses the
default UE_ID value of 0.

3.6.3 Paging Handling Procedure


During system information update, the eNodeB generates a paging message and sets the
systemInfoModification IE at each subsequent PO in a single DRX cycle. To page a single

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 39


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

UE, the eNodeB calculates the nearest PO for the UE, generates a paging message, and sets
the pagingRecord IE. If the eNodeB is scheduled to send the pagingRecord or a
systemInfoModification IE for another UE in this PO, the eNodeB includes all the
information in the paging message.
UEs use DRX in idle mode to reduce power consumption. In each DRX cycle, a UE monitors
only its own POs. In one of the POs, the UE interprets the P-RNTI on the PDCCH and then
reads the paging message on the PDSCH based on the P-RNTI. Multiple UEs may have the
same PO.
A UE in idle mode starts its receiver to monitor the PDCCH at POs in each DRX cycle. After
the UE detects its own paging message, the UE sends a paging response, which is generated at
the NAS, to the MME. The paging response is indicated by mt-Access, the value of the
EstablishmentCause IE contained in the RRC Connection Request message.
If the UE does not interpret the P-RNTI on the PDCCH, or if the UE interprets the P-RNTI
but does not detect its pagingRecord, the UE shuts down the receiver and enters the sleep
mode to reduce power consumption.
When a cell starts broadcasting system information, the cell sends paging messages to inform
all UEs in its coverage of system information update. To ensure that all UEs can be paged
successfully, the cell broadcasts the paging messages using the maximum values of
defaultPagingCycle (256 radio frames) and Ns (4).

3.6.4 Scheduling of Paging Messages


The eNodeB determines coding rates for paging messages based on the
CellDlschAlgo.RarAndPagingCR setting. The PCCHCfg.MaxPagingRecordsNum
parameter specifies the maximum number of UEs that can be included in a paging message.

l If the number of UEs that can be included in a paging message on a paging occasion is
less than or equal to the value of PCCHCfg.MaxPagingRecordsNum, the eNodeB
sends the paging message to all the UEs on the paging occasion.
l If the number of UEs to be paged on each paging occasion is greater than the value of
PCCHCfg.MaxPagingRecordsNum, the eNodeB sends the paging messages for the
UEs according to the strategy specified by PCCHCfg.PagingStrategy.
FIFO
If PCCHCfg.PagingStrategy is set to PAGING_STRATEGY_FIFO(First-in
First-out Strategy), the eNodeB preferentially sends the paging messages for N
UEs that arrive earlier in a paging occasion and sends the paging messages for other
UEs in the next paging cycle. N is specified by the
PCCHCfg.MaxPagingRecordsNum parameter.
Priority Differentiation
If PCCHCfg.PagingStrategy is set to PAGING_STRATEGY_DIFFPRI(Priority
Differentiation Strategy), the eNodeB preferentially selects CS paging messages
and paging messages that have paging priorities and then selects PS paging
messages that do not have paging priorities. The eNodeB then sends the paging
messages for N UEs in a paging occasion and sends the paging messages for other
UEs in the next paging cycle. N is specified by the
PCCHCfg.MaxPagingRecordsNum parameter.
The paging message priority information is carried in paging messages the MME
sends to the eNodeB. Value CS for the CN Domain field in a paging message
indicates CS paging, which is generally used by the CSFB service. Value PS for the

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 40


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 3 Technical Description

CN Domain field in a paging message indicates PS paging, which is generally used


by the packet data service or VoLTE service.
Scheduling of paging messages supports interference randomization (referred to as the
interference randomization-based paging message scheduling function). Specifically, the first
RB to be allocated to paging messages in a cell varies according to the result of (PCI mod 3)
for the cell. Using this RB allocation method ensures that RBs allocated to paging messages
in different cells do not conflict with each other, reducing the inter-message interference.
The interference randomization-based paging message scheduling function is specified by
PagingInterfRandSwitch under CellAlgoSwitch.DlSchSwitch. For details about this
function, see ICIC Feature Parameter Description.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 41


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 4 Related Features

4 Related Features

4.1 LBFD-002009 Broadcast of system information


Prerequisite Features
None

Mutually Exclusive Features


None

Impacted Features
None

4.2 LBFD-002011 Paging


Prerequisite Features
None

Mutually Exclusive Features


None

Impacted Features
None

4.3 LBFD-00201803 Cell Selection and Re-selection


Prerequisite Features
None

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 42


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 4 Related Features

Mutually Exclusive Features


None

Impacted Features
Feature ID Feature Name Description

LOFD-001032 Intra-LTE Load LOFD-001032 Intra-LTE Load Balancing


Balancing uses the dedicated priorities of neighboring
cells.

LOFD-070215 Intra-LTE User During the implementation of Intra-LTE


Number Load User Number Load Balancing, frequencies
Balancing for which
EutranInterNFreq.MeasPerformanceDe-
mand is set to
UNDELIVER(UNDELIVER) cannot
serve as the target frequencies for carrying
UEs in idle mode.

LOFD-00105401 Camp & Handover During SPID-specific cell reselection, non-


Based on SPID serving E-UTRA frequencies for which
EutranInterNFreq.MeasPerformanceDe-
mand is set to
UNDELIVER(UNDELIVER) are not
contained in the IMMCI IE sent to UEs.

LOFD-001112 MOCN Flexible During the implementation of MOCN


Priority Based Flexible Priority Based Camping, non-
Camping serving E-UTRA frequencies for which
EutranInterNFreq.MeasPerformanceDe-
mand is set to
UNDELIVER(UNDELIVER) are not
contained in the IMMCI IE sent to UEs.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 43


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 5 Network Impact

5 Network Impact

5.1 LBFD-002009 Broadcast of system information


System Capacity
No impact.

Network Performance
Broadcast of system information enables UEs in idle mode to acquire system information so
that they can access the network.

Sib6Switch and Sib7Switch of the SiSwitch parameter specify whether the eNodeB
broadcasts SIB6 and SIB7, respectively, and whether UEs in RRC_IDLE mode can reselect to
UTRAN and GERAN. If the two switches are turned off, UEs cannot reselect to UTRAN or
GERAN. In this case, there may be more bad-quality signals on the E-UTRAN, which may
cause the following impacts:

l Jeopardized KPIs, including the PRACH access success rate, RRC setup success rate,
eRAB setup success rate, call drop rate, RRC reestablishment success rate, cell
throughput rate, user throughput rate, IBLER, RBLER, packet loss rate, MOS,
IDLE2ACEIVE activation delay, attach delay, and other delays (such as delay in web
browsing or FTP download)
l More online subscribers
l Higher PRB usage efficiency

The specific impacts vary according to user distribution and cannot be quantified. You can
determine the impacts based on live network conditions.

5.2 LBFD-002011 Paging


System Capacity
No impact.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 44


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 5 Network Impact

Network Performance
Paging ensures that mobile-terminated services can reach the UEs in idle mode.

5.3 LBFD-00201803 Cell Selection and Re-selection


System Capacity
No impact.

Network Performance
Cell selection and reselection ensures sufficient network coverage so that UEs in idle mode
will not become out of service when moving between cells.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 45


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

6 Engineering Guidelines

6.1 When to Use


LBFD-002009 Broadcast of system information, LBFD-002011 Paging, and LBFD-00201803
Cell Selection and Re-selection (intra-RAT) are fundamental to coverage continuity and are
enabled by default.
LBFD-00201803 Cell Selection and Re-selection is recommended to ensure coverage
continuity when multiple systems coexist. It is not recommended when LTE coverage is
contiguous and LTE load is light.
By default, Sib6Switch and Sib7Switch are turned on. Turn off Sib6Switch and Sib7Switch
only when you want to prohibit UEs in E-UTRAN cells from reselecting to UTRAN and
GERAN cells, respectively. For example, turn them off during UTRAN and GERAN network
reconstruction.

6.2 Deployment

6.2.1 Requirements
Other Features
For details, see 4 Related Features.

Hardware
None

License
None

Other Requirements
None

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 46


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

6.2.2 Data Preparation and Feature Activation

6.2.2.1 Data Preparation


This section describes the data that you need to collect for setting parameters. Required data is
data that you must collect for all scenarios. Collect scenario-specific data when necessary for
a specific feature deployment scenario.

Required Data
Configuring frequencies and neighboring cells
For details, see Intra-RAT Mobility Management in Connected Mode Feature Parameter
Description and Inter-RAT Mobility Management in Connected Mode Feature Parameter
Description.
Configuring cell reselection information
The following table describes the parameters that must be set in the CellResel MO to
configure cell reselection.

Parameter Parameter ID Data Source Setting Notes


Name

Local cell CellResel.Loca Radio network Set this parameter to the actual cell ID.
ID lCellId plan (internal
plan)

Threshold CellResel.SNo Engineering If this parameter is set to


for non- nIntraSearchC design NOT_CFG(Not configure), a UE
intra freq fgInd continuously measures the signal quality
measureme of inter-frequency or inter-RAT cells
nts whose priorities are lower than or equal
configure to that of the serving cell, regardless of
indicator the signal quality of the serving cell. As
a result, the UE uses more power.
Therefore, you are advised to set this
parameter to CFG(Configure).

Threshold CellResel.SInt Engineering If this parameter is set to


for intra raSearchCfgIn design NOT_CFG(Not configure), a UE keeps
freq d measuring intra-frequency cells. This
measureme process occurs regardless of the signal
nts quality in the serving cell. Therefore,
configure you are advised to set this parameter to
indicator CFG(Configure).

Cell CellResel.Cell Default value/ This parameter specifies the cell


reselection ReselPriority Recommende reselection priority of the serving
priority d value frequency. The value 0 indicates the
lowest priority. In network planning
scenarios, ensure that the value of this
parameter is lower than the priority of
reselection to UTRAN cells.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 47


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

Parameter Parameter ID Data Source Setting Notes


Name

Serving CellResel.Thrs Engineering This parameter indicates whether to set


frequency hServLowQCf design the RSRQ threshold for reselection to
lower gInd cells on the serving frequency.
priority
RSRQ
threshold
configure
indicator

Minimum CellResel.QQu Engineering This parameter specifies the minimum


required alMinCfgInd design required quality level configure
quality indicator.
level
configure
indicator

Ue max CellResel.PMa Engineering This parameter indicates whether to


power xCfgInd design configure the maximum TX power of
allowed the UE in the intra-frequency
configure neighboring E-UTRAN cell. If this
indicator parameter is set to CFG(Configure), the
maximum TX power is specified by
CellResel.PMax. If the value of this
parameter is set to NOT_CFG(Not
configure), the maximum TX power is
subject to the UE capability.

Max CellResel.PMa Default value/ -


transmit x Recommende
power d value
allowed

Scenario-specific Data
To configure reselection to E-UTRAN inter-frequency, UTRAN, GERAN, or CDMA2000
cells, set the cell reselection priorities and relevant parameters when configuring neighboring
frequencies.
l Reselection to inter-frequency E-UTRAN cells
The following table describes the parameters that must be set in the EutranInterNFreq
MO to configure a neighboring E-UTRAN frequency.
Paramet Parameter ID Data Source Setting Notes
er Name

Local EutranInterNF Radio network -


cell ID req.LocalCellId plan (internal
plan)

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 48


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

Paramet Parameter ID Data Source Setting Notes


er Name

Inter EutranInterNF Default value/ Set this parameter to


frequenc req.CellReselPr Recommended CFG(Configure).
y cell iorityCfgInd value
resel
priority
configure
indicator

Inter EutranInterNF Radio network This parameter specifies the cell


frequenc req.CellReselPr plan (internal reselection priority for the
y cell iority plan) frequency. Set this parameter to a
resel value within the range of 0 to 7. A
priority larger parameter value leads to a
higher probability of measuring
neighboring cells and redirecting
UEs.

l Reselection to UTRAN cells


The following table describes the parameter that must be set in the CellSiMap MO to
configure the SIB6 switch.
Paramet Paramet Data Source Setting Notes
er Name er ID

Cell CellSiM Radio network By default, turn on the Sib6Switch


System ap.SiSwit plan (internal switch to allow UEs to reselect to the
Informati ch plan) UTRAN system. Turn off the
on Sib6Switch only when you want to
Switch prohibit UEs from reselecting to the
UTRAN system.

The following table describes the parameter that must be set in the CellReselUtran MO
to configure cell reselection to UTRAN.
Paramet Parameter ID Data Source Setting Notes
er Name

Local cell CellReselUtran.Loc Radio network -


ID alCellId plan (internal
plan)

The following table describes the parameters that must be set in the UtranNFreq MO to
configure UTRAN frequencies.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 49


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

Paramete Paramete Data Source Setting Notes


r Name r ID

Local cell UtranNFr Radio network plan -


ID eq.LocalC (internal plan)
ellId

Reselectio UtranNFr Default value/ Set this parameter to


n priority eq.CellRe Recommended value CFG(Configure). If this parameter
configure selPriority is set to NOT_CFG(Not
indicator CfgInd configure), the cell reselection
priority cannot be set.

Cell UtranNFr Radio network plan -


reselectio eq.CellRe (internal plan)
n priority selPriority

l Reselection to GERAN cells


The following table describes the parameter that must be set in the CellSiMap MO to
configure the SIB7 switch.
Paramet Paramet Data Source Setting Notes
er Name er ID

Cell CellSiM Radio network By default, turn on the Sib7Switch


System ap.SiSwit plan (internal switch to allow UEs to reselect to the
Informati ch plan) GERAN system. Turn off the
on Sib7Switch only when you want to
Switch prohibit UEs from reselecting to the
GERAN system.

The following table describes the parameter that must be set in the CellReselGeran MO
to configure cell reselection to GERAN.
Paramete Paramete Data Source Setting Notes
r Name r ID

Local cell CellResel Radio network plan -


ID Geran.Lo (internal plan)
calCellId

The following table describes the parameters that must be set in the GeranNfreqGroup
MO to configure GERAN frequencies.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 50


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

Paramete Paramete Data Source Setting Notes


r Name r ID

Local cell GeranNfr Radio network plan -


ID eqGroup. (internal plan)
LocalCell
Id

BCCH GeranNfr Radio network plan This parameter specifies the ID of


group ID eqGroup. (internal plan) the GERAN carrier frequency
BcchGrou group. In cell reselection, GERAN
pId frequencies are grouped. Each
GERAN frequency group uses the
same GERAN cell reselection
parameters. Set this parameter to a
value ranging from 0 to 31.

Cell GeranNfr Engineering design Set this parameter to


reselection eqGroup. CFG(Configure).
priority CellResel
configure PriorityCf
indicator gInd

Cell GeranNfr Engineering design -


reselection eqGroup.
priority CellResel
Priority

l Reselection to CDMA2000 cells


The following table describes the parameters that must be set in the
CellReselCdma2000 MO to configure cell reselection to CDMA2000.
Paramete Paramete Data Source Setting Notes
r Name r ID

Local cell CellResel Radio network plan -


ID Cdma200 (internal plan)
0.LocalCe
llId

System CELLRE Engineering design If the eNodeB supports time


time SELCDM synchronization
informatio A2000.Sys (TASM.CLKSYNCMODE set to
n TimeCfgI TIME(TIME)), set this parameter
configure nd to CFG(Configure).
indicator If the eNodeB supports frequency
synchronization
(TASM.CLKSYNCMODE set to
FREQ(FREQ)), set this parameter
to NOT_CFG(Not configure).

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 51


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

Paramete Paramete Data Source Setting Notes


r Name r ID

HRPD CellResel Engineering design Set this parameter to


parameters Cdma200 CFG(Configure) to allow UEs to
configure 0.HrpdPa reselect to CDMA2000HRPD cells.
indicator raCfgInd

HRPD cell CellResel Engineering design Set this parameter to


reselection Cdma200 CFG(Configure) to allow UEs to
configure 0.HrpdCel reselect to CDMA2000HRPD cells.
indicator lReselectP
aramCfgI
nd

1XRTT CellResel Engineering design Set this parameter to


parameters Cdma200 CFG(Configure) to allow UEs to
configure 0.Cdma1X reselect to CDMA2000 1XRTT
indicator rttParaCf cells.
gInd

1XRTT CellResel Engineering design Set this parameter to


cell Cdma200 CFG(Configure) to allow UEs to
reselection 0.Cdma1X reselect to CDMA2000 1XRTT
configure rttCellRes cells.
indicator elCfgInd

The following table describes the parameters that must be set in the
Cdma2000BandClass MO to configure CDMA2000 frequency bands.
Paramete Paramete Data Source Setting Notes
r Name r ID

Local cell Cdma200 Radio network plan -


ID 0BandCla (internal plan)
ss.LocalC
ellId

Band class Cdma200 Radio network plan -


0BandCla (internal plan)
ss.BandCl
ass

CDMA200 Cdma200 Radio network plan This parameter specifies whether to


01XRTT 0BandCla (internal plan) set the reselection priority of a
cell ss.Cdma2 CDMA2000 1xRTT cell. When this
reselection 0001XrttC parameter is set to NOT_CFG(Not
indicator ellReselIn configure), the system information
d does not contain the reselection
priority of a CDMA2000 1xRTT
cell.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 52


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

Paramete Paramete Data Source Setting Notes


r Name r ID

CDMA200 Cdma200 Radio network plan This parameter specifies the cell
01XRTT 0BandCla (internal plan) reselection priority for the
cell ss.Cdma2 frequency. Set this parameter to a
reselection 0001XrttC value within the range of 0 to 7.
priority ellReselPr
i

CDMA200 Cdma200 Radio network plan This parameter specifies whether to


0HRPD 0BandCla (internal plan) set the reselection priority of a
cell ss.Cdma2 CDMA2000 HRPD cell. When this
reselection 000HrpdC parameter is set to NOT_CFG(Not
indicator ellReselIn configure), the system information
d does not contain the reselection
priority of a CDMA2000 HRPD
cell.

CDMA200 Cdma200 Radio network plan This parameter specifies the cell
0HRPD 0BandCla (internal plan) reselection priority for the
cell ss.Cdma2 frequency. Set this parameter to a
reselection 000HrpdC value within the range of 0 to 7.
priority ellReselPr
i

l Speed-based cell reselection


The following table describes the parameters that must be set in the CellResel MO to
configure speed-based cell reselection parameters and intra-frequency neighboring E-
UTRAN cell parameters.
Paramet Parameter ID Data Source Setting Notes
er
Name

Speed- CellResel.Speed Engineering This parameter indicates whether to


depende DepReselCfgIn design set the speed-dependent scaling
nt d parameters related to cell
reselecti reselection. Speed-based cell
on reselection is enabled by setting this
paramete parameter to CFG(Configure) and a
r specific neighboring cell parameter
configur to CFG(Configure).
e
indicator

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 53


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

Paramet Parameter ID Data Source Setting Notes


er
Name

Speed CellResel.Speed Engineering This parameter indicates whether to


state StateSfCfgInd design enable speed-based cell reselection
scale to intra-frequency neighboring E-
factor UTRAN cells. Set this parameter to
configur CFG(Configure) to enable speed-
e based cell reselection to intra-
indicator frequency neighboring E-UTRAN
cells.

The following table describes the parameters that must be set in the EutranInterNFreq
MO to configure inter-frequency neighboring E-UTRAN cell parameters.
Paramet Parameter ID Data Source Setting Notes
er
Name

Speed EutranInterNF Default value/ This parameter indicates whether to


depende req.SpeedDepe Recommended enable speed-based cell reselection
nt resel ndSPCfgInd value to inter-frequency neighboring E-
paramete UTRAN cells. Set this parameter to
r CFG(Configure) to enable speed-
configuri based cell reselection to inter-
ng frequency neighboring E-UTRAN
indicator cells.

Scaling EutranInterNF Engineering A smaller value of this parameter


factor of req.TReselEutr design leads to a shorter decision duration
treseleutr anSfMedium of reselection to a cell on a
an in neighboring E-UTRAN frequency
medium for a medium-mobility UE and a
mobility higher probability of cell reselection.
state A larger value of this parameter
leads to the opposite effects. If the
value of this parameter is too large
or too small, the access success rate
is affected.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 54


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

Paramet Parameter ID Data Source Setting Notes


er
Name

Scaling EutranInterNF Engineering A smaller value of this parameter


factor of req.TReselEutr design leads to a shorter decision duration
treseleutr anSfHigh of reselection to a cell on a
an in neighboring E-UTRAN frequency
high for a high-mobility UE and a higher
mobility probability of cell reselection. A
state larger value of this parameter leads
to the opposite effects. If the value
of this parameter is too large or too
small, the access success rate is
affected.

The following table describes the parameter that must be set in the CellReselUtran MO
to configure neighboring UTRAN cell parameters.
Paramet Parameter ID Data Source Setting Notes
er
Name

Speed CellReselUtran Engineering This parameter specifies whether to


state .SpeedStateSfCf design enable speed-based cell reselection
scale gInd to neighboring UTRAN cells. Set
factor this parameter to CFG(Configure)
configur to enable speed-based cell
e reselection to neighboring UTRAN
indicator cells.

The following table describes the parameters that must be set in the CellReselGeran
MO to configure neighboring GERAN cell parameters.
Paramet Parameter ID Data Source Setting Notes
er
Name

Speed CellReselGeran Engineering This parameter specifies whether to


state .SpeedStateSfCf design enable speed-based cell reselection
scale gInd to neighboring GERAN cells. Set
factor this parameter to CFG(Configure)
configur to enable speed-based cell
e reselection to neighboring GERAN
indicator cells.

The following table describes the parameters that must be set in the
CellReselCdma2000 MO to configure neighboring CDMA2000 cell parameters.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 55


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

Paramet Parameter ID Data Source Setting Notes


er
Name

Speed CellReselCdma Engineering This parameter specifies whether to


state 2000.SpeedStat design enable speed-based cell reselection
scale eSfCfgInd to neighboring CDMA2000 HRPD
factor cells. Set this parameter to
configur CFG(Configure) to enable speed-
e based cell reselection to neighboring
indicator CDMA2000 HRPD cells.

1XRTT CellReselCdma Engineering This parameter specifies whether to


speed 2000.Cdma1Xrt design enable speed-based cell reselection
state tSpeedStateCfgI to neighboring CDMA2000 1XRTT
scale nd cells. Set this parameter to
factors CFG(Configure) to enable speed-
configur based cell reselection to neighboring
e CDMA2000 1xRTT cells.
indicator

6.2.2.2 Using the CME


For detailed operations, see CME-based Feature Configuration.

6.2.2.3 Using MML Commands

MML Commands
For details about how to configure frequencies and neighboring cells, see Intra-RAT Mobility
Management in Connected Mode Feature Parameter Description and Inter-RAT Mobility
Management in Connected Mode Feature Parameter Description.

l Reselection to inter-frequency E-UTRAN cells

Step 1 Run the MOD EUTRANINTERNFREQ command with Inter frequency cell resel priority
configure indicator set to CFG(Configure) and with Local cell ID and Inter frequency cell
resel priority set based on actual conditions.

----End

l Reselection to UTRAN cells

Step 1 Run the MOD CELLSIMAP command with Sib6Switch(Sib6Switch) under Cell System
Information Switch selected.

Step 2 Run the ADD CELLRESELUTRAN command to add the configurations related to
reselection to UTRAN cells. In this step, set Local cell ID based on actual conditions, and
retain the default values for other parameters.

Step 3 Run the MOD CELLRESEL command with Cell reselection priority set to an appropriate
value.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 56


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

Step 4 Run the MOD UTRANNFREQ command with Reselection priority configure indicator
set to CFG(Configure) and with Local cell ID, Downlink UARFCN, and Cell reselection
priority set based on actual conditions.

Step 5 Run the MOD RRCCONNSTATETIMER command to set Ue inactive timer to a value
rather than 0.

----End

l Reselection to GERAN cells

Step 1 Run the MOD CELLSIMAP command with Sib7Switch(Sib7Switch) under Cell System
Information Switch selected.

Step 2 Run the ADD CELLRESELGERAN command to add the configurations related to
reselection to GERAN cells. In this step, set Local cell ID based on actual conditions, and
retain the default values for other parameters.

Step 3 Run the MOD CELLRESEL command with Cell reselection priority set to an appropriate
value.

Step 4 Run the MOD GERANNFREQGROUP command with Cell reselection priority configure
indicator set to CFG(Configure) and with Local cell ID, BCCH group ID, and Cell
reselection priority set based on actual conditions.

Step 5 Run the ADD GERANNFREQGROUPARFCN command to add neighboring GERAN


BCCH frequencies.

Step 6 Run the MOD RRCCONNSTATETIMER command to set Ue inactive timer to a value
rather than 0.

----End

l Reselection to CDMA2000 HRPD cells

Step 1 Run the ADD CELLRESELCDMA2000 command to add the configurations related to
reselection to CDMA2000 cells. In this step, set both HRPD parameters configure
indicator and HRPD cell reselection configure indicator to CFG(Configure).

Step 2 Run the MOD CELLRESEL command with Cell reselection priority set to an appropriate
value.

Step 3 Run the MOD CDMA2000BANDCLASS command with CDMA2000HRPD cell


reselection indicator set to CFG(Configure). In this step, set Local cell ID, Band class, and
CDMA2000HRPD cell reselection priority based on actual conditions.

Step 4 Run the MOD RRCCONNSTATETIMER command to set Ue inactive timer to a value
rather than 0.

----End

l Reselection to CDMA2000 1xRTT cells

Step 1 Run the ADD CELLRESELCDMA2000 command to add the configurations related to
reselection to CDMA2000 cells. In this step, set both 1XRTT parameters configure
indicator and 1XRTT cell reselection configure indicator to CFG(Configure).

Step 2 Run the MOD CELLRESEL command with Cell reselection priority set to an appropriate
value.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 57


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

Step 3 Run the MOD CDMA2000BANDCLASS command with CDMA20001XRTT cell


reselection indicator set to CFG(Configure). In this step, set Local cell ID, Band class, and
CDMA20001XRTT cell reselection priority based on actual conditions.
Step 4 Run the MOD RRCCONNSTATETIMER command to set Ue inactive timer to a value
rather than 0.

----End
l Speed-based cell reselection
NOTE

Speed-based cell reselection is supported only when cell reselection for UEs at normal speed has
been enabled.

Step 1 Run the MOD CELLRESEL command to configure speed-based cell reselection and intra-
frequency neighboring E-UTRAN cell parameters. In this step, set both Speed-dependent
reselection parameter configure indicator and Speed state scale factor configure
indicator to CFG(Configure).
Step 2 Configure neighboring cell parameters based on the neighboring cell type.
l Configuring inter-frequency neighboring E-UTRAN cell parameters
Run the MOD EUTRANINTERNFREQ command with Speed dependent resel
parameter configuring indicator set to CFG(Configure) and with Scaling factor of
treseleutran in medium mobility state and Scaling factor of treseleutran in high
mobility state set based on actual conditions.
l Configuring neighboring UTRAN cell parameters
Run the MOD CELLRESELUTRAN command with Speed state scale factor
configure indicator set to CFG(Configure).
l Configuring neighboring GERAN cell parameters
Run the MOD CELLRESELGERAN command with Speed state scale factor
configure indicator set to CFG(Configure).
l Configuring neighboring CDMA2000 HRPD cell parameters
Run the MOD CELLRESELCDMA2000 command with HRPD parameters
configure indicator, HRPD cell reselection configure indicator, and Speed state scale
factor configure indicator set to CFG(Configure).
l Configuring neighboring CDMA2000 1xRTT cell parameters
Run the MOD CELLRESELCDMA2000 command with 1XRTT parameters
configure indicator, 1XRTT cell reselection configure indicator, and 1XRTT speed
state scale factors configure indicator set to CFG(Configure).

----End

MML Command Examples


l Reselection to inter-frequency E-UTRAN cells
MOD EUTRANINTERNFREQ: LocalCellId=0, DlEarfcn=3600,
CellReselPriorityCfgInd=CFG, CellReselPriority=5;

l Reselection to UTRAN cells


MOD CELLSIMAP:LOCALCELLID=0,SISWITCH=Sib6Switch-1;
ADD CELLRESELUTRAN: LocalCellId=0, TReselUtran=1, SpeedStateSfCfgInd=NOT_CFG;
MOD CELLRESEL: LocalCellId=0, CellReselPriority=6;
MOD UTRANNFREQ: LocalCellId=0, UtranDlArfcn=10738,
CellReselPriorityCfgInd=CFG, CellReselPriority=7;

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 58


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

MOD RRCCONNSTATETIMER: UeInactiveTimer=20;

l Reselection to GERAN cells


MOD CELLSIMAP:LOCALCELLID=0,SISWITCH=Sib7Switch-1;
ADD CELLRESELGERAN: LocalCellId=0, TReselGeran=1, SpeedStateSfCfgInd=NOT_CFG;
MOD CELLRESEL: LocalCellId=0, CellReselPriority=6;
MOD GERANNFREQGROUP: LocalCellId=0, BcchGroupId=0, GeranVersion=EDGE,
StartingArfcn=800, BandIndicator=GSM_dcs1800, CellReselPriorityCfgInd=CFG,
CellReselPriority=7;
ADD GERANNFREQGROUPARFCN: LocalCellId=0, BcchGroupId=0, GeranArfcn=1;
MOD RRCCONNSTATETIMER: UeInactiveTimer=20;

l Reselection to CDMA2000 HRPD cells


If the eNodeB supports time synchronization (TASM.CLKSYNCMODE set to
TIME(TIME)):
//Setting parameters related to cell reselection to CDMA2000
ADD CELLRESELCDMA2000: LocalCellId=0, SysTimeCfgInd=CFG,
SearchWndSizeCfgInd=CFG, HrpdParaCfgInd=CFG,
HrpdCellReselectParamCfgInd=CFG, Cdma1XrttParaCfgInd=NOT_CFG;

//Setting cell reselection priority


MOD CELLRESEL: LocalCellId=0, CellReselPriority=6;

//Configuring CDMA2000 neighboring frequency bands


MOD CDMA2000BANDCLASS: LocalCellId=0, BandClass=bc4,
Cdma2000HrpdCellReselInd=CFG, Cdma2000HrpdCellReselPri=3;

//Setting the UE inactivity timer to a value rather than 0


MOD RRCCONNSTATETIMER: UeInactiveTimer=20;

If the eNodeB supports frequency synchronization (TASM.CLKSYNCMODE set to


FREQ(FREQ)):
//Setting parameters related to cell reselection to CDMA2000
ADD CELLRESELCDMA2000: LocalCellId=0, SysTimeCfgInd=NOT_CFG,
SearchWndSizeCfgInd=CFG, HrpdParaCfgInd=CFG,
HrpdCellReselectParamCfgInd=CFG, Cdma1XrttParaCfgInd=NOT_CFG;

//Setting cell reselection priority


MOD CELLRESEL: LocalCellId=0, CellReselPriority=6;

//Configuring CDMA2000 neighboring frequency bands


MOD CDMA2000BANDCLASS: LocalCellId=0, BandClass=bc4,
Cdma2000HrpdCellReselInd=CFG, Cdma2000HrpdCellReselPri=3;

//Setting the UE inactivity timer to a value rather than 0


MOD RRCCONNSTATETIMER: UeInactiveTimer=20;

l Reselection to CDMA2000 1XRTT cells


ADD CELLRESELCDMA2000: LocalCellId=0, SysTimeCfgInd=NOT_CFG,
SearchWndSizeCfgInd=NOT_CFG, HrpdParaCfgInd=NOT_CFG, Cdma1XrttParaCfgInd=CFG,
Cdma1XrttCellReselCfgInd=CFG, Cdma1XrttSpeedStateCfgInd=NOT_CFG;
MOD CELLRESEL: LocalCellId=0, CellReselPriority=6;
MOD CDMA2000BANDCLASS: LocalCellId=0, BandClass=bc7,
Cdma20001XrttCellReselInd=CFG, Cdma20001XrttCellReselPri=4;
MOD RRCCONNSTATETIMER: UeInactiveTimer=20;

l Speed-based cell reselection


MOD CELLRESEL: LocalCellId=0, SpeedDepReselCfgInd=CFG, SpeedStateSfCfgInd=CFG;
MOD EUTRANINTERNFREQ: LocalCellId=0, DlEarfcn=3600, SpeedDependSPCfgInd=CFG,
TReselEutranSfMedium=1DOT0_ENUM, TReselEutranSfHigh=0DOT75_ENUM;
MOD CELLRESELUTRAN: LocalCellId=0, SpeedStateSfCfgInd=CFG;
MOD CELLRESELGERAN: LocalCellId=0, SpeedStateSfCfgInd=CFG;
MOD CELLRESELCDMA2000: LocalCellId=0, HrpdParaCfgInd=CFG,
HrpdCellReselectParamCfgInd=CFG, SpeedStateSfCfgInd=CFG;
MOD CELLRESELCDMA2000: LocalCellId=0, Cdma1XrttParaCfgInd=CFG,
Cdma1XrttCellReselCfgInd=CFG, Cdma1XrttSpeedStateCfgInd=CFG;

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 59


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

6.2.3 Activation Observation


Reselection to an Inter-Frequency E-UTRAN Cell
Step 1 Enable a UE in idle mode to camp on an E-UTRAN cell. Set the cell reselection priority of an
E-UTRAN frequency. Trace the Uu messages of the E-UTRAN cell. The SIB5 carries the cell
reselection priority of the E-UTRAN frequency (cellReselectionPriority). The following
figure shows the messages.

Step 2 Enable the UE in idle mode to move to the E-UTRAN cell edge. Use the UE to perform
services, to trigger the UE to switch from idle mode to connected mode. Observe the Uu
messages of the E-UTRAN cell.
If the RRC_CONNECT_REQ message exists, cell reselection has succeeded.

----End

Reselection to an Inter-RAT Cell


The following describes how to verify reselection to a UTRAN cell.

Step 1 Enable a UE in idle mode to camp on an E-UTRAN cell. Set the cell reselection priority of a
UTRAN frequency. Trace the Uu messages of the E-UTRAN cell. The SIB6 carries the cell
reselection priority of the UTRAN frequency (cellReselectionPriority). The following figure
shows the messages.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 60


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

Step 2 Enable the UE in idle mode to move to the E-UTRAN cell edge. Observe the Uu messages of
the UTRAN cell. If the value of the establishmentCause IE in the RRC_CONNECT_REQ
message is interRAT-CellReselection, cell reselection was successful. The following figure
shows the messages.

----End

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 61


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

Speed-based Cell Reselection


Verify cell reselection in the following steps (speed-based reselection to an E-UTRAN inter-
frequency cell is used as an example):

Step 1 Enable a UE in idle mode to camp on an E-UTRAN cell. Configure parameters related to
speed-based cell reselection to inter-frequency neighboring E-UTRAN cells. Observe the Uu
messages of the E-UTRAN cell. Speed-based cell reselection to inter-frequency neighboring
E-UTRAN cells, that is, t-ReselectionEUTRA-SF.sf-Medium and t-ReselectionEUTRA-
SF.sf-High, are contained in SIB5. The following figure shows the messages.

Step 2 Enable the UE in idle mode to quickly move to the E-UTRAN cell edge. Use the UE to
perform services, to trigger the UE to switch from idle mode to connected mode. Observe the
Uu messages of the E-UTRAN cell. If the RRC_CONNECT_REQ message exists, cell
reselection was successful.

----End

6.2.4 Reconfiguration
N/A

6.2.5 Deactivation

6.2.5.1 Using the CME


For detailed operations, see CME-based Feature Configuration.

6.2.5.2 Using MML Commands

MML Commands
l Deactivating reselection to an inter-frequency E-UTRAN cell
Run the MOD EUTRANINTERNFREQ command with Inter frequency cell resel
priority configure indicator set to NOT_CFG(Not configure).
l Deactivating reselection to a UTRAN cell
Method 1:

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 62


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

a. Run the MOD UTRANNFREQ command with Reselection priority configure


indicator set to NOT_CFG(Not configure).
b. Run the RMV CELLRESELUTRAN command to remove the configuration for
reselection to UTRAN cells.
Method 2:
Run the MOD CELLSIMAP command with Sib6Switch(Sib6Switch) under Cell
System Information Switch deselected to deactivate cell reselection to UTRAN.
l Deactivating reselection to a GERAN cell
Method 1:
a. Run the MOD GERANNFREQGROUP command with Cell reselection priority
configure indicator set to NOT_CFG(Not configure).
b. Run the RMV CELLRESELGERAN command to remove the configuration for
reselection to GERAN cells.
Method 2:
Run the MOD CELLSIMAP command with Sib7Switch(Sib7Switch) under Cell
System Information Switch deselected to deactivate cell reselection to GERAN.
l Deactivating reselection to a CDMA2000 HRPD cell
a. Run the MOD CDMA2000BANDCLASS command with CDMA2000HRPD cell
reselection indicator set to NOT_CFG(Not configure).
b. If the configuration for reselection to a CDMA2000 HRPD cell is available, run the
MOD CELLRESELCDMA2000 command with the HRPD parameters
configure indicator parameter set to NOT_CFG(Not configure). If the
configuration for reselection to a CDMA2000 HRPD cell is unavailable, run the
RMV CELLRESELCDMA2000 command to remove the configuration for
reselection to CDMA2000 HRPD cells.
l Deactivating reselection to a CDMA2000 1xRTT cell
a. Run the MOD CDMA2000BANDCLASS command with CDMA20001XRTT
cell reselection indicator set to NOT_CFG(Not configure).
b. If the configuration for reselection to a CDMA2000 1xRTT cell is available, run the
MOD CELLRESELCDMA2000 command with the 1XRTT parameters
configure indicator parameter set to NOT_CFG(Not configure). If the
configuration for reselection to a CDMA2000 1xRTT cell is unavailable, run the
RMV CELLRESELCDMA2000 command to remove the configuration for
reselection to CDMA2000 1xRTT cells.
l Deactivating speed-based cell reselection
NOTE

If inter-frequency or inter-RAT cell reselection is deactivated, inter-frequency or inter-RAT speed-


based cell reselection is deactivated at the same time, without requiring additional operations.
Method 1: Deactivating speed-based cell reselection to all neighboring cells
Run the MOD CELLRESEL command with Speed-dependent reselection parameter
configure indicator set to NOT_CFG(Not configure).
Method 2: Deactivating speed-based cell reselection to some neighboring cells
Deactivating speed-based cell reselection to intra-frequency neighboring E-UTRAN
cells
Run the MOD CELLRESEL command with Speed state scale factor configure
indicator set to NOT_CFG(Not configure).

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 63


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

Deactivating speed-based cell reselection to inter-frequency neighboring E-UTRAN


cells
Run the MOD EUTRANINTERNFREQ command with Speed dependent resel
parameter configuring indicator set to NOT_CFG(Not configure).
Deactivating speed-based cell reselection to neighboring UTRAN cells
Run the MOD CELLRESELUTRAN command with Speed state scale factor
configure indicator set to NOT_CFG(Not configure).
Deactivating speed-based cell reselection to neighboring GERAN cells
Run the MOD CELLRESELGERAN command with Speed state scale factor
configure indicator set to NOT_CFG(Not configure).
Deactivating speed-based cell reselection to neighboring CDMA2000 HRPD cells
Run the MOD CELLRESELCDMA2000 command with HRPD parameters
configure indicator and HRPD cell reselection configure indicator set to
CFG(Configure) and with Speed state scale factor configure indicator set to
NOT_CFG(Not configure).
Deactivating speed-based cell reselection to neighboring CDMA2000 1xRTT cells
Run the MOD CELLRESELCDMA2000 command with 1XRTT parameters
configure indicator and 1XRTT cell reselection configure indicator set to
CFG(Configure) and with 1XRTT speed state scale factors configure indicator
set to NOT_CFG(Not configure).

MML Command Examples


l Deactivating reselection to an inter-frequency E-UTRAN cell
MOD EUTRANINTERNFREQ: LocalCellId=0, DlEarfcn=3600,
CellReselPriorityCfgInd=NOT_CFG;

l Deactivating reselection to a UTRAN cell


Method 1:
MOD UTRANNFREQ: LocalCellId=0, UtranDlArfcn=10738,
CellReselPriorityCfgInd=NOT_CFG;
RMV CELLRESELUTRAN: LocalCellId=0;

Method 2:
MOD CELLSIMAP: LocalCellId=0, SiSwitch=Sib6Switch-0;

l Deactivating reselection to a GERAN cell


Method 1:
MOD GERANNFREQGROUP: LocalCellId=0, BcchGroupId=0,
CellReselPriorityCfgInd=NOT_CFG;
RMV CELLRESELGERAN: LocalCellId=0;

Method 2:
MOD CELLSIMAP: LocalCellId=0, SiSwitch=Sib7Switch-0;

l Deactivating reselection to a CDMA2000 HRPD cell


MOD CDMA2000BANDCLASS: LocalCellId=0, BandClass=bc4,
Cdma2000HrpdCellReselInd=NOT_CFG;
MOD CELLRESELCDMA2000: LocalCellId=0, HrpdParaCfgInd=NOT_CFG;
RMV CELLRESELCDMA2000: LocalCellId=0;

l Deactivating reselection to a CDMA2000 1XRTT cell


MOD CDMA2000BANDCLASS: LocalCellId=0, BandClass=bc7,
Cdma20001XrttCellReselInd=NOT_CFG;
MOD CELLRESELCDMA2000: LocalCellId=0, Cdma1XrttParaCfgInd=CFG,
Cdma1XrttCellReselCfgInd=NOT_CFG;
RMV CELLRESELCDMA2000: LocalCellId=0;

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 64


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

l Deactivating speed-based cell reselection


Method 1: Deactivating speed-based cell reselection to all neighboring cells
MOD CELLRESEL: LocalCellId=0, SpeedDepReselCfgInd=NOT_CFG;
Method 2: Deactivating speed-based cell reselection to some neighboring cells
MOD CELLRESEL: LocalCellId=0, SpeedStateSfCfgInd=NOT_CFG;
MOD EUTRANINTERNFREQ: LocalCellId=0, DlEarfcn=3600,
SpeedDependSPCfgInd=NOT_CFG;
MOD CELLRESELUTRAN: LocalCellId=0, SpeedStateSfCfgInd=NOT_CFG;
MOD CELLRESELGERAN: LocalCellId=0, SpeedStateSfCfgInd=NOT_CFG;
MOD CELLRESELCDMA2000: LocalCellId=0, HrpdParaCfgInd=CFG,
HrpdCellReselectParamCfgInd=CFG, SpeedStateSfCfgInd=NOT_CFG;
MOD CELLRESELCDMA2000: LocalCellId=0, Cdma1XrttParaCfgInd=CFG,
Cdma1XrttCellReselCfgInd=CFG, Cdma1XrttSpeedStateCfgInd=NOT_CFG;

6.3 Performance Monitoring


LBFD-00201803 Cell Selection and Re-selection does not have the counter statistics result.
The following describes the counters used to monitor LBFD-002009 Broadcast of system
information and LBFD-002011 Paging.

Counter ID Counter Name Counter Description

1526726884 L.Paging.S1.Rx Number of paging messages received over the S1


interface in a cell. This counter reflects the
signaling overhead brought by the UE in idle
mode.

1526726885 L.Paging.UU.Att Estimated paging success rate. In a paging group,


divide L.Paging.UU.Att for a single cell by the
1526726886 L.Paging.UU.Succ sum of L.Paging.UU.Succ for all cells in the
paging group to obtain the paging success rate.
NOTE
Generally, the EPC sends paging messages to all cells in
a paging group, the value of L.Paging.UU.Att for each
cell is similar. This way, you can use this method to
estimate the paging success rate.
If the EPC supports certain enhanced paging features,
some UEs in a paging group may receive paging
message from another paging group and the values of
L.Paging.UU.Att may greatly differ among the cells in
the same paging group. In this case, you cannot use this
method to estimate the paging success rate.
You can obtain the precise paging success rate from the
EPC.

1526727212 L.Paging.Dis.Num Number of discarded MME-delivered paging


messages in a cell.

1526728521 L.Paging.Dis.PchC Number of paging messages discarded due to PCH


ong congestion in a cell.

1526728337 L.Paging.UU.SIUp Number of paging messages delivered over the Uu


date interface due to system information changes in a
cell.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 65


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

6.4 Parameter Optimization


Cell Selection
The following table describes the parameters that must be set in the CellSel MO to configure
cell selection.

Parameter Name Parameter ID Setting Notes

Minimum required CellSel.QRxLevMi Set this parameter properly so that the


RX level n selected cells can provide signals that meet
the quality requirement of basic services.

Minimum required CellSel.QRxLevMi A larger value of this parameter leads to a


RX level offset nOffset higher probability of the cell meeting criteria
S and becoming a suitable cell for cell
selection. A smaller value of this parameter
results in a lower probability.

Minimum required CellSel.QQualMin This parameter is used to calculate the


RX quality level serving sell Squal for cell selection and
reselection. If RSRQ-related parameters are
delivered to control cell selection and
reselection, set this parameter to a value
other than 0.
If only RSRP-related parameters are
delivered to control cell selection and
reselection, set this parameter to 0.

Minimum required CellSel.QQualMin A larger value of this parameter leads to a


RX quality level Offset higher probability of the cell meeting criteria
offset S and becoming a suitable cell for cell
selection. A smaller value of this parameter
results in a lower probability.

The following table describes the parameter that must be set in the CELL MO to configure
the maximum allowed transmit power.

Parameter Name Parameter ID Setting Notes

Max transmit power CELL.UePowerM A larger value results in higher maximum


allowed ax transmit power for UEs and stronger signal
strength in the local cell but higher
interference to neighboring cells. A smaller
value leads to the opposite effect.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 66


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

Neighboring Cell Measurement


l Intra-frequency measurement
The following table describes the parameters that must be set in the CellResel MO to
configure cell reselection.
Parameter Parameter ID Setting Notes
Name

Threshold for CellResel.SIntra Set this parameter to a value greater than the
intra frequency Search value of the CellResel.SNonIntraSearch
measurements parameter. With all other conditions
unchanged, a larger value of this parameter
leads to a higher probability of triggering
intra-frequency cell measurements, and a
smaller value indicates a lower probability.

RSRQ Threshold CELLRESEL.S With other conditions unchanged, a larger


for intra IntraSearchQ value of this parameter leads to a higher
frequency probability of triggering intra-frequency cell
measurements measurements, and a smaller value indicates
a lower probability.

l Inter-frequency or inter-RAT measurement


The following table describes the parameters that must be set in the CellResel MO to
configure cell reselection.
Parameter Parameter ID Setting Notes
Name

Threshold for CellResel.SNonI Set this parameter to a value less than that of
non-intra ntraSearch SIntraSearch.
frequency
measurements

RSRQ Threshold CellResel.SNonI With other conditions unchanged, a larger


for non-intra ntraSearchQ value of this parameter leads to a higher
frequency probability of triggering inter-frequency or
measurements inter-RAT measurements, and a smaller
value indicates a lower probability.

Cell Reselection
l Intra-frequency or equal-priority cell reselection
The following table describes the parameters that must be set in the CellResel MO to
configure cell reselection.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 67


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

Parameter Parameter ID Setting Notes


Name

Minimum CellResel.QRxL Set this parameter to an appropriate value so


required RX level evMin that the selected cell can provide signals that
meet the quality requirement of basic
services.

Cell reselection CellResel.TResel A smaller parameter value for a cell leads to


timer value for Eutran a high probability that UEs in this cell
EUTRAN initiate reselection and also a high
probability of ping-pong reselection. A
larger parameter value for a cell leads to low
probabilities.

Hysteresis value CellResel.Qhyst This parameter is used to adjust the border of


for ranking the serving cell, to avoid ping-pong effect of
criteria cell reselection. A larger value of
CellResel.Qhyst leads to larger coverage of
the serving cell and therefore a lower
probability of reselection to the neighboring
cell.

The following table describes the parameter that must be set in the
EutranIntraFreqNCell MO to configure neighbor relationships of intra-frequency E-
UTRAN cells.
Parameter Name Parameter ID Setting Notes

Cell offset EutranIntraFreq This parameter is used to adjust the


NCell.CellQoffset border of neighboring cells. A larger
value of EutranIntraFreqN-
Cell.CellQoffset leads to smaller
coverage of the neighboring cell and
therefore a lower probability of
reselection to the neighboring cell.

l Reselection of inter-frequency or inter-RAT cells on different-priority frequencies


The following table describes the parameters that must be set in the CellResel MO to
configure cell reselection.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 68


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

Parameter Parameter ID Setting Notes


Name

Serving frequency CellResel.Thrsh This parameter specifies the threshold used


lower priority ServLow in the evaluation of reselection to a cell on a
threshold lower-priority E-UTRAN frequency or on an
inter-RAT frequency. Cell reselection to a
cell on a lower-priority E-UTRAN frequency
or on an inter-RAT frequency is performed if
no cell on the serving frequency or on a
higher-priority E-UTRAN frequency fulfills
criteria 1 for inter-frequency and inter-RAT
reselections.
A smaller value of this parameter leads to a
lower probability of reselection to low-
priority inter-frequency or inter-RAT cells.

Serving frequency CellResel.Thrsh With other conditions unchanged, a smaller


lower priority ServLowQ value of this parameter leads to a lower
RSRQ threshold probability of reselection to an inter-
frequency or inter-RAT cell on lower-
priority frequencies, and a larger value of
this parameter leads to a higher probability.

The following table describes the parameters that must be set in the EutranInterNFreq
MO to configure a non-serving E-UTRA frequency.
Parameter Name Parameter ID Setting Notes

PMAX EutranInterNFreq. A smaller value of this parameter


PMax results in a lower signal quality
requirement for reselection to a
cell on the non-serving E-UTRA
frequency, decreasing the access
success rate of the cell. A larger
value of this parameter results in
the opposite effect.

Minimum RX signal EutranInterNFreq. A larger value of this parameter


quality QQualMin leads to lower probabilities that a
cell meets criterion S and becomes
a suitable cell selected by a UE. A
smaller value of this parameter
leads to higher probabilities.

Frequency offset EutranInterNFreq. A larger value of this parameter


QoffsetFreq results in a lower probability of
reselection to cells on the non-
serving E-UTRA frequency. A
smaller value of this parameter
leads to the opposite effect.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 69


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

Parameter Name Parameter ID Setting Notes

Inter frequency high EutranInterNFreq. A smaller value of this parameter


priority RSRQ threshold ThreshXHighQ results in a larger probability of
reselection to a cell on the non-
serving E-UTRA frequency,
decreasing the access success rate
of the cell. A larger value of this
parameter results in the opposite
effect.

Inter frequency low EutranInterNFreq. A smaller value of this parameter


priority RSRQ threshold ThreshXlowQ results in a larger probability of
reselection to a cell on the non-
serving E-UTRA frequency,
decreasing the access success rate
of the cell. A larger value of this
parameter results in the opposite
effect.

Inter frequency high EutranInterNFreq. With other conditions unchanged,


priority threshold ThreshXhigh a larger value of this parameter
leads to a lower probability of
such reselection, and a smaller
value of this parameter leads to a
higher probability.

Inter frequency lower EutranInterNFreq. With other conditions unchanged,


priority threshold ThreshXlow a larger value of this parameter
leads to a lower probability of
such reselection, and a smaller
value of this parameter leads to a
higher probability.

Minimum required RX EutranInterNFreq. Set this parameter to an


level QRxLevMin appropriate value so that the
selected cell can provide signals
that meet the quality requirement
of basic services.

EUTRAN reselection EutranInterNFreq. -


time EutranReselTime

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 70


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

Parameter Name Parameter ID Setting Notes

Measurement EutranInterNFreq. Set this parameter to


Performance Demand MeasPerformance- UNDELIVER(UNDELIVER) for
Demand downlink frequencies without
corresponding uplink frequencies.
You are advised to set this
parameter to
NORMAL(NORMAL) for other
frequencies to meet the following
requirements:
l At least one frequency for
intensive coverage is included.
l Frequencies on the main
capacity layer, such as those
with a large bandwidth, high
UE penetration rate, and good
coverage, are included as much
as possible.

The following table describes the parameters that must be set in the UtranNFreq MO to
configure UTRAN frequencies.
Parameter Name Parameter ID Setting Notes

Minimum required UtranNFreq.Qqu A larger value of this parameter leads to


quality level almin lower probabilities that a UTRAN FDD
cell meets criterion S and becomes a
suitable cell selected by a UE. A smaller
value of this parameter leads to higher
probabilities.

PMAX UtranNFreq.Pma -
xUtran

UTRAN high UtranNFreq.Thr With other conditions unchanged, a larger


priority RSRQ eshXHighQ value of this parameter leads to a lower
threshold probability of such reselection, and a
smaller value leads to a higher probability.

UTRAN low UtranNFreq.Thr With other conditions unchanged, a larger


priority RSRQ eshXLowQ value of this parameter leads to a lower
threshold probability of such reselection, and a
smaller value leads to a higher probability.

Minimum required UtranNFreq.QRx Set this parameter to an appropriate value


RX level LevMin so that the selected cell can provide signals
that meet the quality requirement of basic
services.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 71


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

Parameter Name Parameter ID Setting Notes

UTRAN high UtranNFreq.Thr With other conditions unchanged, a larger


priority threshold eshXHigh value of this parameter leads to a lower
probability of such reselection, and a
smaller value leads to a higher probability.

UTRAN lower UtranNFreq.Thr With other conditions unchanged, a larger


priority threshold eshXLow value of this parameter leads to a lower
probability of such reselection, and a
smaller value leads to a higher probability.

The following table describes the parameter that must be set in the CellReselUtran MO
to configure cell reselection to UTRAN.
Parameter Parameter ID Setting Notes
Name

Cell reselection CellReselUtran With other conditions unchanged, a larger value


timer value for .TReselUtran of this parameter leads to a lower probability of
UTRAN such reselection, and a smaller value leads to a
higher probability.

The following table describes the parameters that must be set in the GeranNfreqGroup
MO to configure GERAN frequencies.
Parameter Parameter ID Setting Notes
Name

High priority GeranNfreqGroup.Thres With other conditions unchanged, a


threshold hXHigh larger value of this parameter leads
to a lower probability of such
reselection, and a smaller value leads
to a higher probability.

Lower priority GeranNfreqGroup.Thres With other conditions unchanged, a


threshold hXLow larger value of this parameter leads
to a lower probability of such
reselection, and a smaller value leads
to a higher probability.

PMAX GeranNfreqGroup.Pmax -
Geran

Minimum GeranNfreqGroup.QRxL Set this parameter to an appropriate


required RX evMin value so that the selected cell can
level provide signals that meet the quality
requirement of basic services.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 72


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

The following table describes the parameter that must be set in the CellReselGeran MO
to configure cell reselection to GERAN.

Parameter Parameter ID Setting Notes


Name

Cell reselection CellReselGera With other conditions unchanged, a larger value


timer value for n.TReselGeran of this parameter leads to a lower probability of
GERAN such reselection, and a smaller value leads to a
higher probability.

The following table describes the parameters that must be set in the
CellReselCdma2000 MO to configure cell reselection to CDMA2000.

Parameter Parameter ID Setting Notes


Name

Cell reselection CellReselCdma2 With other conditions unchanged, a larger


timer for HRPD 000.Treselection value of this parameter leads to a lower
Hrpd probability of such reselection, and a
smaller value leads to a higher probability.

Cell reselection CellReselCdma2 A smaller parameter value for a cell leads to


timer for 1XRTT 000.Cdma1XrttTr a high probability that UEs in this cell
eselection initiate reselection and also a high
probability of ping-pong reselection. A
larger parameter value for a cell leads to
low probabilities.

The following table describes the parameters that must be set in the
Cdma2000BandClass MO to configure CDMA2000 frequency bands.

Parameter Name Parameter ID Setting Notes

CDMA20001XRT Cdma2000BandClass. A larger value of this parameter


T high priority Cdma20001XrttThresh indicates a lower probability of a UE
threshold XHigh camping on the cells assigned with
the band class, and a smaller value
indicates a higher probability.

CDMA20001XRT Cdma2000BandClass. A larger value of this parameter


T lower priority Cdma20001XrttThresh indicates a lower probability of a UE
threshold XLow camping on the cells assigned with
the band class, and a smaller value
indicates a higher probability.

CDMA2000HRP Cdma2000BandClass. A larger value of this parameter


D high priority Cdma2000HrpdThresh indicates a lower probability of a UE
threshold XHigh camping on the cells assigned with
the band class, and a smaller value
indicates a higher probability.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 73


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

Parameter Name Parameter ID Setting Notes

CDMA2000HRP Cdma2000BandClass. A larger value of this parameter


D lower priority Cdma2000HrpdThresh indicates a lower probability of a UE
threshold XLow camping on the cells assigned with
the band class, and a smaller value
indicates a higher probability.

l Speed-based cell reselection


The following table describes the parameters that must be set in the CellResel MO to
configure common speed-based cell reselection parameters and speed-based cell
reselection parameters related to intra-frequency neighboring E-UTRAN cells.
Parameter Parameter ID Setting Notes
Name

The duration for CellResel.TEval A smaller value of this parameter leads to a


evaluating criteria uation lower probability of the UE entering the high
to enter mobility mobility or medium mobility state. A larger
states value of this parameter leads to the opposite
effect.

Additional time CellResel.THyst A larger value of this parameter leads to a


hysteresis for Normal slower decision on speed change and a
normal speed smaller impact of UE speed variation on cell
reselection. A smaller value of this parameter
leads to the opposite effect.

The number of CellResel.NCell A larger value of this parameter indicates a


cell changes to ChangeMedium lower probability of a UE entering the
enter medium medium mobility state and cell reselections
mobility state are more difficult to trigger. A smaller value
of this parameter leads to the opposite effect.

The number of CellResel.NCell A larger value of this parameter indicates a


cell changes to ChangeHigh lower probability of a UE entering the high
enter high mobility state and cell reselections are more
mobility state difficult to trigger. A smaller value of this
parameter leads to the opposite effect.

Additional CellResel.QHyst A smaller value of this parameter results in a


hysteresis for SfMedium higher speed of cell reselection for medium-
medium speed mobility UEs. A larger value of this
parameter leads to the opposite effect.

Additional CellResel.QHyst A smaller value of this parameter results in a


hysteresis for SfHigh higher speed of cell reselection for high-
high speed mobility UEs. A larger value of this
parameter leads to the opposite effect.

Scaling factor of CellResel.TRese A smaller value of this parameter results in a


TReselEutran in lEutranSfMediu higher speed of cell reselection for medium-
medium mobility m mobility UEs. A larger value of this
state parameter leads to the opposite effect.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 74


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

Parameter Parameter ID Setting Notes


Name

Scaling factor of CellResel.TRese A smaller value of this parameter results in a


TReselEutran in lEutranSfHigh higher speed of cell reselection for high-
high mobility mobility UEs. A larger value of this
state parameter leads to the opposite effect.

The following table describes the parameters that must be set in the EutranInterNFreq
MO to configure speed-based cell reselection parameters related to inter-frequency
neighboring E-UTRAN cells.
Parameter Parameter ID Setting Notes
Name

Scaling factor of EutranInterNFr A smaller value of this parameter results in a


treseleutran in eq.TReselEutran higher speed of cell reselection for medium-
medium mobility SfMedium mobility UEs. A larger value of this
state parameter leads to the opposite effect.

Scaling factor of EutranInterNFr A smaller value of this parameter results in a


treseleutran in eq.TReselEutran higher speed of cell reselection for high-
high mobility SfHigh mobility UEs. A larger value of this
state parameter leads to the opposite effect.

The following table describes the parameters that must be set in the CellReselUtran MO
to configure speed-based cell reselection to neighboring UTRAN cells.
Parameter Parameter ID Setting Notes
Name

Scaling factor of CellReselUtran. A smaller value of this parameter results in a


TReselUtran in TReselUtranSfM higher speed of cell reselection for medium-
medium mobility edium mobility UEs. A larger value of this
state parameter leads to the opposite effect.

Scaling factor of CellReselUtran. A smaller value of this parameter results in a


TReselUtran in TReselUtranSfHi higher speed of cell reselection for high-
high mobility gh mobility UEs. A larger value of this
state parameter leads to the opposite effect.

The following table describes the parameters that must be set in the CellReselGeran
MO to configure speed-based cell reselection to neighboring GERAN cells.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 75


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

Parameter Parameter ID Setting Notes


Name

Scaling factor of CellReselGeran. A smaller value of this parameter results in a


TReselGeran in TReselGeranSfM higher speed of cell reselection for medium-
medium mobility edium mobility UEs. A larger value of this
state parameter leads to the opposite effect.

Scaling factor of CellReselGeran. A smaller value of this parameter results in a


TReselGeran in TReselGeranSfH higher speed of cell reselection for high-
high mobility igh mobility UEs. A larger value of this
state parameter leads to the opposite effect.

The following table describes the parameters that must be set in the
CellReselCdma2000 MO to configure speed-based cell reselection to neighboring
CDMA2000 cells.
Parameter Parameter ID Setting Notes
Name

Scaling factor of CellReselCdma2 A smaller value of this parameter results in a


TReselCdmaHrpd 000.TReselCdma higher speed of cell reselection for medium-
in medium HrpdSfMedium mobility UEs. A larger value of this
mobility state parameter leads to the opposite effect.

Scaling factor of CellReselCdma2 A smaller value of this parameter results in a


TReselCdmaHrpd 000.TReselCdma higher speed of cell reselection for high-
in high mobility HrpdSfHigh mobility UEs. A larger value of this
state parameter leads to the opposite effect.

1XRTT medium CellReselCdma2 A smaller value of this parameter results in a


speed scale factor 000.Cdma1XrttSf higher speed of cell reselection for medium-
Medium mobility UEs. A larger value of this
parameter leads to the opposite effect.

1XRTT high CellReselCdma2 A smaller value of this parameter results in a


speed scale factor 000.Cdma1XrttSf higher speed of cell reselection for high-
High mobility UEs. A larger value of this
parameter leads to the opposite effect.

Paging
l Paging success rate
Decreasing the paging message code rate specified by CellDlschAlgo.RarAndPagingCR
helps improve the paging success rate.
However, decreasing the paging message code rate increases the PDSCH resources
occupied by paging messages, which causes the downlink throughput to decrease.
With UE compatibility problems taken into account, set the paging message code rate to
0.035 or higher (setting CellDlschAlgo.RarAndPagingCR to 35). The number of single-
paging-message RBs less than or equal to 40% of the total number of single-TTI RBs
ensures sufficient downlink power. When adjusting the

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 76


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

CellDlschAlgo.RarAndPagingCR parameter setting, you are advised to limit the


number of paging records contained in a single paging message (specified by
PCCHCfg.MaxPagingRecordsNum) to control the maximum number of single-paging-
message RBs.
The following table lists the recommended values for
PCCHCfg.MaxPagingRecordsNum in case of different
CellDlschAlgo.RarAndPagingCR values (20 MHz bandwidth used as an example). You
can estimate the recommended values for PCCHCfg.MaxPagingRecordsNum in the
event of other bandwidths based on those for the 20 MHz bandwidth.

Number of Single- CellDlschAlgo.RarAndPag PCCHCfg.MaxPagingRe


Paging-Message ingCR cordsNum
RBs

40 78 16

40 73 15

40 69 14

40 64 13

40 60 12

40 55 11

40 50 10

40 45 9

40 41 8

40 36 7

37 35 6

NOTE

In this table, the recommended number of RBs is calculated based on the paging messages
containing UE flags "S-TMSI".
To estimate the recommended values for PCCHCfg.MaxPagingRecordsNum in case of any given
value of CellDlschAlgo.RarAndPagingCR in the above table, do as follows:
l 10 MHz bandwidth
Divide the number of single-paging-message RBs and the value of
PCCHCfg.MaxPagingRecordsNum by 2, and then round down the results to integers.
l 5 MHz bandwidth
Divide the number of single-paging-message RBs and the value of
PCCHCfg.MaxPagingRecordsNum by 4, and then round down the results to integers.
For other bandwidths, estimate the recommended values in the same manner.
l Uu interface paging capacity
The Uu interface paging capacity is related to nB (specified by PCCHCfg.Nb) and the
number of paging message records (specified by PCCHCfg.MaxPagingRecordsNum).
The maximum number of paging message sent over the Uu interface within 1s is equal to

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 77


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 6 Engineering Guidelines

the result of (nB/T) multiplied by 100 and PCCHCfg.MaxPagingRecordsNum, where T


represents the paging cycle.
NOTE

The above formula calculates the theoretical maximum paging capacity, and the actual paging
capacity is also related to the hardware processing capability.
Assume nB equals 1T, and the value of PCCHCfg.MaxPagingRecordsNum is 16, a
maximum of 1600 UEs can be paged over the Uu interface within 1s. You can increase
nB and PCCHCfg.MaxPagingRecordsNum to increase the Uu interface paging
capacity. However, increasing nB increases the overhead of PDCCHs occupied by
paging messages.
When adjusting the PCCHCfg.MaxPagingRecordsNum setting, query the paging
message code rate specified by CellDlschAlgo.RarAndPagingCR, and ensure that the
number of single-paging message RBs is less than or equal to 40% of the total number of
single-TTI RBs, in accordance with the description in the preceding table.
l Paging priority
If paging messages are congested over the Uu interface, you are advised to set
PCCHCfg.PagingStrategy to PAGING_STRATEGY_DIFFPRI(Priority
Differentiation Strategy), to ensure that CS paging messages or high-priority paging
messages are preferentially sent over the Uu interface.

System Information Update


If the paging occasion (PO) of a UE supporting Single Radio LTE (SRLTE) falls in the paging
monitoring window of a CDMA2000 1X network, the UE cannot receive paging messages
from the LTE network, and cannot update LTE system information. As a result, RRC
establishment may fail.
You are advised to turn on the CellSiMap.SibUpdOptSwitch in scenarios with both CDMA
and LTE network coverage.
l If this switch is turned on, when the paging cycle of the LTE network is less than that of
the CDMA network, RRC establishment failures can be avoided; when the paging cycle
of the LTE network is greater than or equal to that of the CDMA network, the problem
persists.
l If this switch is turned off, the problem persists regardless of the paging periods of LTE
and CDMA networks.

6.5 Possible Issues


None

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 78


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

7 Parameters

Table 7-1 Parameters


MO Parame MML Feature Feature Description
ter ID Comma ID Name
nd

EutranIn MeasPer ADD LBFD-0 Broadca Meaning: Indicates the measurement performance
terNFre formanc EUTRA 02009/ st of demand for whether to broadcast the frequency in
q eDeman NINTE TDLBF system SIB5. If this parameter is set to NORMAL, the
d RNFRE D-00200 informat frequency is broadcast in interFreqCarrierFreqList
Q 9 ion without carrying the IE reducedMeasPerformance.
MOD LBFD-0 Cell The measurement performance of a UE is normal
EUTRA 0201803 Selectio when the UE measures the frequency. If this
NINTE / n and parameter is set to REDUCED, the frequency is
RNFRE TDLBF Re- broadcast in interFreqCarrierFreqListExt carrying the
Q D-00201 selection IE reducedMeasPerformance. The measurement
803 performance of a UE supporting extensive frequency
LST measurement can be reduced to measure the
EUTRA frequency. If this parameter is set to UNDELIVER,
NINTE the frequency is not broadcast in SIB5. This parameter
RNFRE value applies only to LTE FDD. For details about the
Q IE reducedMeasPerformance, see 3GPP TS 36.331.
GUI Value Range: NORMAL(NORMAL),
REDUCED(REDUCED),
UNDELIVER(UNDELIVER)
Unit: None
Actual Value Range: NORMAL, REDUCED,
UNDELIVER
Default Value: NORMAL(NORMAL)

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 79


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellAcc CellBarr MOD LBFD-0 Cell Meaning: Indicates whether the cell is barred. If the
ess ed CELLA 02013 / Outage cell is barred, the UE cannot camp on the serving cell.
CCESS TDLBF Detectio During cell reselection, the serving cell is not selected
LST D-00203 n and as a candidate cell.
CELLA 7 Compen GUI Value Range: CELL_BARRED(Barred),
CCESS LBFD-0 sation CELL_NOT_BARRED(Not Barred)
02009 / Broadca Unit: None
TDLBF st of
D-00200 system Actual Value Range: CELL_BARRED,
9/ informat CELL_NOT_BARRED
MLBFD ion Default Value: CELL_NOT_BARRED(Not Barred)
-120002 RAN
29 Sharing
LOFD-0 with
01036 / Commo
TDLOF n
D-00103 Carrier
6

CellOp CellRes ADD LBFD-0 Broadca Meaning:


ervedFo CELLO 02009 / st of Indicates whether the cell is reserved for operator use.
rOp P TDLBF system
MOD D-00200 informat If this parameter is set to
CELLO 9/ ion CELL_RESERVED_FOR_OP, the cell is reserved for
P MLBFD RAN operator use. UEs of AC11 or AC15 in their HPLMN
-120002 Sharing or EHPLMN can consider this cell as a candidate cell
LST 29 for cell selection or reselection. UEs of AC11 or
CELLO with
LOFD-0 Commo AC15 outside their HPLMN/EHPLMN and UEs of
P AC0-9/AC12-14 consider this cell as a barred cell
01036 / n
TDLOF Carrier during cell selection or reselection.
D-00103 If this parameter is set to
6 CELL_NOT_RESERVED_FOR_OP, the cell is not
reserved for operator use. All UEs can consider this
cell as a candidate cell for cell selection or reselection.
This parameter applies to LTE FDD, LTE TDD, and
NB-IoT.
GUI Value Range:
CELL_RESERVED_FOR_OP(Reserved),
CELL_NOT_RESERVED_FOR_OP(Not Reserved)
Unit: None
Actual Value Range: CELL_RESERVED_FOR_OP,
CELL_NOT_RESERVED_FOR_OP
Default Value:
CELL_NOT_RESERVED_FOR_OP(Not Reserved)

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 80


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellSel QRxLev MOD LBFD-0 Broadca Meaning: Indicates the minimum required RX level
Min CELLS 02009 / st of for the cell to become a candidate for cell selection.
EL TDLBF system This value is included in criteria S and used in the
LST D-00200 informat evaluation of cell selection. For details, see 3GPP TS
CELLS 9/ ion 36.304.
EL MLBFD Cell GUI Value Range: -70~-22
-120002 Selectio
29 Unit: 2dBm
n and
LBFD-0 Re- Actual Value Range: -140~-44
0201803 selection Default Value: -64
/
TDLBF
D-00201
803 /
MLBFD
-120002
37

CellSel QRxLev MOD LBFD-0 Cell Meaning: Indicates the offset to the minimum required
MinOffs CELLS 0201803 Selectio RX level. This value is included in criteria S and used
et EL / n and in the evaluation of cell selection. This parameter is
LST TDLBF Re- valid only when the cell selection is triggered by
CELLS D-00201 selection periodic searches for higher-priority PLMNs and the
EL 803 Broadca UE is served by a Visited Public Land Mobile
LBFD-0 st of Network (VPLMN). For details, see 3GPP TS 36.304.
02009 / system This parameter applies only to LTE FDD and LTE
TDLBF informat TDD.
D-00200 ion GUI Value Range: 0~8
9 Unit: 2dB
Actual Value Range: 0~16
Default Value: 0

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 81


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

Cell UePowe ADD LBFD-0 Uplink Meaning: Indicates the maximum transmit power that
rMax CELL 02026 / Power a UE can apply to uplink transmission in the cell. It is
MOD TDLBF Control used in cell selection criterion S to calculate the
CELL D-00202 Broadca compensated power. If the value of this parameter is
6 st of not specified, the maximum power is subject to the
LST UE capability. For details, see 3GPP TS 36.304.
CELL LBFD-0 system
02009 / informat GUI Value Range: -30~36
TDLBF ion Unit: dBm
D-00200 Cell
9/ Actual Value Range: -30~36
Selectio
MLBFD n and Default Value: 23
-120002 Re-
29 selection
LBFD-0
0201803
/
TDLBF
D-00201
803

CellSel QQualM MOD LBFD-0 Broadca Meaning: Indicates the minimum required received
in CELLS 02009 / st of signal quality, which corresponds to the q-QualMin IE
EL TDLBF system in system information block type 1 (SIB1) and is used
LST D-00200 informat to calculate the Squal value for the serving cell
CELLS 9/ ion involved in cell selection and reselection. If this
EL MLBFD Cell parameter is set to 0, SIB1 does not contain the q-
-120002 Selectio QualMin IE. If this parameter is set to a value other
29 n and than 0, SIB1 contains the q-QualMin IE with the same
LBFD-0 Re- value as the parameter value. For details about this
0201803 selection parameter, see 3GPP TS 36.304.
/ GUI Value Range: -34~-3,0
TDLBF Unit: dB
D-00201
803 / Actual Value Range: -34~-3,0
MLBFD Default Value: 0
-120002
37

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 82


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes ThrshSe MOD LBFD-0 Broadca Meaning: Indicates whether to set the RSRQ threshold
el rvLowQ CELLR 02009 / st of for reselection to cells on the serving frequency. This
CfgInd ESEL TDLBF system parameter applies only to LTE FDD and LTE TDD.
LST D-00200 informat GUI Value Range: NOT_CFG(Not configure),
CELLR 9 ion CFG(Configure)
ESEL LBFD-0 Cell Unit: None
0201803 Selectio
/ n and Actual Value Range: NOT_CFG, CFG
TDLBF Re- Default Value: NOT_CFG(Not configure)
D-00201 selection
803

CellSel QQualM MOD LBFD-0 Broadca Meaning: Indicates the offset to the minimum required
inOffset CELLS 02009 / st of RX level for the cell. It is included in criteria S and
EL TDLBF system used in the evaluation of cell selection. This parameter
LST D-00200 informat is required only when the cell selection is triggered by
CELLS 9 ion periodic searches for higher-priority PLMNs and the
EL LBFD-0 Cell UE is served by a Visited Public Land Mobile
0201803 Selectio Network (VPLMN). For details, see 3GPP TS 36.304.
/ n and This parameter applies only to LTE FDD and LTE
TDLBF Re- TDD.
D-00201 selection GUI Value Range: 1~8
803 Unit: dB
Actual Value Range: 1~8
Default Value: 1

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 83


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes CellRes MOD LBFD-0 Cell Meaning: Indicates the cell reselection priority of the
el elPriorit CELLR 0201803 Selectio serving frequency. 0 indicates the lowest priority. The
y ESEL / n and value of this parameter must be determined together
LST TDLBF Re- with the priorities of other frequencies during the
CELLR D-00201 selection network planning. Frequencies used for different
ESEL 803 Broadca RATs must be assigned different cell reselection
LBFD-0 st of priorities. This parameter applies only to LTE FDD
02009 / system and LTE TDD.
TDLBF informat GUI Value Range: 0~7
D-00200 ion Unit: None
9 PS Inter- Actual Value Range: 0~7
LOFD-0 RAT
01021 / Mobility Default Value: 7
TDLOF between
D-00102 E-
1 UTRAN
LOFD-0 and
01111 CDMA2
000
TDLOF
D-00111 PS
2 Mobility
from E-
UTRAN
to
CDMA2
000
HRPD
Based
on
Frequen
cy-
specific
Factors
MOCN
Flexible
Priority
Based
Campin
g

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 84


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

EutranIn CellRes ADD LBFD-0 Cell Meaning: Indicates the cell reselection priority of the
terNFre elPriorit EUTRA 0201803 Selectio neighboring E-UTRAN frequency. The value 0
q y NINTE / n and indicates the lowest priority. It is contained in system
RNFRE TDLBF Reselect information block type 5 (SIB5). The UE decides
Q D-00201 ion whether to reselect a neighboring cell on the
MOD 803 frequency based on the value of this parameter and the
EUTRA absolute priority of the serving cell. If the value of this
NINTE parameter is larger than the absolute priority of the
RNFRE serving cell, the UE starts measurements on
Q neighboring cells on the frequency; then if the signal
quality of some neighboring cells meets the related
LST conditions, the UE starts cell reselection. If the value
EUTRA of this parameter is less than or equal to the absolute
NINTE priority of the serving cell, the UE starts the
RNFRE measurements only when the signal quality of the
Q serving cell is poor; then if the signal quality of some
neighboring cells meets the related conditions, the UE
starts cell reselection. Different cell reselection
priorities must be assigned for frequencies of different
RATs. For details, see 3GPP TS 36.331. This
parameter applies only to LTE FDD and LTE TDD.
GUI Value Range: 0~7
Unit: None
Actual Value Range: 0~7
Default Value: 1

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 85


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

UtranNF CellRes ADD LBFD-0 Cell Meaning:


req elPriorit UTRAN 0201803 Selectio Indicates the cell reselection priority of the
y NFREQ / n and neighboring UTRAN frequency. The value 0 indicates
MOD TDLBF Re- the lowest priority. The UE decides whether to
UTRAN D-00201 selection reselect a neighboring cell on the UTRAN frequency
NFREQ 803 Broadca based on the value of this parameter and the absolute
LST LBFD-0 st of priority of the serving cell.
UTRAN 02009 / system
TDLBF informat If the value of this parameter is larger than the
NFREQ absolute priority of the serving cell, the UE starts
D-00200 ion
9 measurements on neighboring cells on the UTRAN
S1-flex frequency; then if the signal quality of some
LBFD-0 neighboring cells meets the related conditions, the UE
01018 / starts cell reselection.
TDLBF
D-00101 If the value of this parameter is smaller than the
8 absolute priority of the serving cell, the UE starts the
measurements only when the signal quality of the
serving cell is poor; then if the signal quality of some
neighboring cells meets the related conditions, the UE
starts cell reselection. Frequencies used for different
RATs must be assigned different cell reselection
priorities. For details, see 3GPP TS 36.331. This
parameter applies only to LTE FDD and LTE TDD.
GUI Value Range: 0~7
Unit: None
Actual Value Range: 0~7
Default Value: 1

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 86


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

GeranNf CellRes ADD LBFD-0 Cell Meaning: Indicates the cell reselection priority of the
reqGrou elPriorit GERAN 0201803 Selectio GERAN carrier frequency group. The value 0
p y NFREQ / n and indicates the lowest priority. It is contained in system
GROUP TDLBF Reselect information block type 7 (SIB7). The UE decides
MOD D-00201 ion whether to reselect a neighboring cell on a frequency
GERAN 803 in the GERAN carrier frequency group based on the
NFREQ value of this parameter and the absolute priority of the
GROUP serving cell. If the value of this parameter is larger
than the absolute priority of the serving cell, the UE
LST starts measurements on neighboring cells on the
GERAN frequencies in the GERAN carrier frequency group;
NFREQ then if the signal quality of some neighboring cells
GROUP meets the related conditions, the UE starts cell
reselection. If the value of this parameter is smaller
than the absolute priority of the serving cell, the UE
starts the measurements only when the signal quality
of the serving cell is poor; then if the signal quality of
some neighboring cells meets the related conditions,
the UE starts cell reselection. Frequencies used for
different RATs must be assigned different cell
reselection priorities. For details, see 3GPP TS
36.331. This parameter applies only to LTE FDD and
LTE TDD.
GUI Value Range: 0~7
Unit: None
Actual Value Range: 0~7
Default Value: 1

Cdma20 Cdma20 ADD LBFD-0 Cell Meaning: Indicates the absolute priority of the
00Band 001Xrtt CDMA2 0201803 Selectio CDMA2000 1xRTT band class to be used during cell
Class CellRes 000BA / n and reselection. The value 0 indicates the lowest priority.
elPri NDCLA TDLBF Re- Frequencies used for different RATs must be assigned
SS D-00201 selection different cell reselection priorities. The information is
MOD 803 CS contained in SIB8. For details, see 3GPP TS 36.331.
CDMA2 LOFD-0 Fallback This parameter applies only to LTE FDD and LTE
000BA 01035 / to TDD.
NDCLA TDLOF CDMA2 GUI Value Range: 0~7
SS D-00103 000 Unit: None
LST 5 1xRTT
Actual Value Range: 0~7
CDMA2 LOFD-0 Enhance
000BA 01090 / d CS Default Value: 2
NDCLA TDLOF Fallback
SS D-00109 to
0 CDMA2
000
1xRTT

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 87


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

Cdma20 Cdma20 ADD LBFD-0 Cell Meaning: Indicates the absolute priority of the
00Band 00Hrpd CDMA2 0201803 Selectio CDMA2000 HRPD band class to be used during cell
Class CellRes 000BA / n and reselection. The value 0 indicates the lowest priority.
elPri NDCLA TDLBF Re- Frequencies used for different RATs must be assigned
SS D-00201 selection different cell reselection priorities. The information is
MOD 803 PS Inter- contained in SIB8. For details, see 3GPP TS 36.331.
CDMA2 LOFD-0 RAT This parameter applies only to LTE FDD and LTE
000BA 01021 / Mobility TDD.
NDCLA TDLOF between GUI Value Range: 0~7
SS D-00102 E- Unit: None
LST 1 UTRAN
and Actual Value Range: 0~7
CDMA2 LOFD-0
000BA 01111 CDMA2 Default Value: 2
NDCLA 000
SS PS
Mobility
from E-
UTRAN
to
CDMA2
000
HRPD
Based
on
Frequen
cy-
specific
Factors

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 88


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

EutranN CellRes ADD LOFD-0 RAN Meaning: Indicates the cell reselection priority of the
FreqRan elPriorit EUTRA 01036 / Sharing operator that shares the neighboring E-UTRAN
Share y NNFRE TDLOF with frequency. The value 0 indicates the lowest priority. If
QRANS D-00103 Commo the related SPID configuration is specified, the cell
HARE 6 n reselection priority specified in the SPID
MOD TDLBF Carrier configuration is used. If no related SPID configuration
EUTRA D-00201 Cell is specified but this parameter is set, the eNodeB
NNFRE 803 Selectio delivers the cell reselection priorities of all PLMNs
QRANS n and supported by a UE by using the IE idleModeMobility-
LOFD-0 ControlInfo in an RRC Connection Release message
HARE 01112 / Re-
selection to the UE. If no related SPID configuration is
LST TDLOF specified and this parameter is not set, a UE uses the
EUTRA D-00111 MOCN common frequency reselection priority of the
NNFRE 2 Flexible neighboring E-UTRAN frequency, which is broadcast
QRANS LOFD-0 Priority in the system information. This parameter applies only
HARE 70206 / Based to LTE FDD and LTE TDD.
TDLOF Campin
g GUI Value Range: 0~7
D-08122
4 Hybrid Unit: None
LBFD-0 RAN Actual Value Range: 0~7
0201803 Sharing Default Value: 0
Cell
Selectio
n and
Re-
selection

UtranRa CellRes ADD LOFD-0 RAN Meaning: Indicates the cell reselection priority of the
nShare elPriorit UTRAN 01036 / Sharing operator that shares the neighboring UTRAN
y RANSH TDLOF with frequency. The value 0 indicates the lowest priority. If
ARE D-00103 Commo the related SPID configuration is specified, set this
MOD 6 n priority to the one specified in the SPID configuration.
UTRAN LBFD-0 Carrier If no related SPID configuration is specified but this
RANSH 0201803 Cell parameter is set, the eNodeB delivers the cell
ARE / Selectio reselection priorities of all PLMNs supported by a UE
TDLBF n and by using the IE idleModeMobilityControlInfo in an
LST RRC Connection Release message to the UE. If no
UTRAN D-00201 Re-
803 selection related SPID configuration is specified and this
RANSH parameter is not set, a UE uses the common cell
ARE LOFD-0 MOCN reselection priority of the neighboring UTRAN
01112 / Flexible frequency, which is broadcast in the system
TDLOF Priority information. This parameter applies only to LTE FDD
D-00111 Based and LTE TDD.
2 Campin
g GUI Value Range: 0~7
LOFD-0
70206 / Hybrid Unit: None
TDLOF RAN Actual Value Range: 0~7
D-08122 Sharing Default Value: 0
4

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 89


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

GeranRa CellRes ADD LOFD-0 RAN Meaning: Indicates the cell reselection priority of the
nShare elPriorit GERAN 01036 / Sharing operator that shares the neighboring GERAN carrier
y RANSH TDLOF with frequency group. The value 0 indicates the lowest
ARE D-00103 Commo priority. If the related SPID configuration is specified,
MOD 6 n set this priority to the one specified in the SPID
GERAN LBFD-0 Carrier configuration. If no related SPID configuration is
RANSH 0201803 Cell specified but this parameter is set, the eNodeB
ARE / Selectio delivers the cell reselection priorities of all PLMNs
TDLBF n and supported by a UE by using the IE idleModeMobility-
LST ControlInfo in an RRC Connection Release message
GERAN D-00201 Re-
803 selection to the UE. If no related SPID configuration is
RANSH specified and this parameter is not set, a UE uses the
ARE LOFD-0 MOCN common cell reselection priority of the neighboring
01112 / Flexible GERAN carrier frequency group, which is broadcast
TDLOF Priority in the system information. This parameter applies only
D-00111 Based to LTE FDD and LTE TDD.
2 Campin
g GUI Value Range: 0~7
LOFD-0
70206 / Hybrid Unit: None
TDLOF RAN Actual Value Range: 0~7
D-08122 Sharing Default Value: 0
4

EutranN CellRes ADD LOFD-0 MOCN Meaning: Indicates the cell reselection dedicated
FreqSCe elDediPr EUTRA 01112 / Flexible priority for an E-UTRAN frequency based on the
llOp i NNFRE TDLOF Priority PLMN ID of the local cell. The value 0 indicates the
QSCEL D-00111 Based lowest priority. If the related SPID configuration is
LOP 2 Campin specified, the cell reselection priority specified in the
MOD LBFD-0 g SPID configuration is used. If no related SPID
EUTRA 0201803 Cell configuration is specified but this parameter is set, the
NNFRE / Selectio eNodeB delivers the cell reselection priorities of all
QSCEL TDLBF n and PLMNs supported by a UE by using the IE
LOP D-00201 Re- idleModeMobilityControlInfo in an RRC Connection
803 selection Release message to the UE. If no related SPID
LST configuration is specified and this parameter is not set,
EUTRA LOFD-0 RAN a UE uses the common frequency reselection priority
NNFRE 01036 Sharing of the neighboring E-UTRAN frequency, which is
QSCEL with broadcast in the system information. This parameter
LOP Commo applies only to LTE FDD and LTE TDD.
n
Carrier GUI Value Range: 0~7
Unit: None
Actual Value Range: 0~7
Default Value: 0

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 90


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

UtranNF CellRes ADD LOFD-0 MOCN Meaning: Indicates the dedicated cell reselection
reqSCell elDediPr UTRAN 01112 / Flexible priority for a UTRAN frequency based on the PLMN
Op i NFREQ TDLOF Priority ID of the local cell. The value 0 indicates the lowest
SCELL D-00111 Based priority. If the related SPID configuration is specified,
OP 2 Campin set this priority to the one specified in the SPID
MOD LBFD-0 g configuration. If no related SPID configuration is
UTRAN 0201803 Cell specified but this parameter is set, the eNodeB
NFREQ / Selectio delivers the cell reselection priorities of all PLMNs
SCELL TDLBF n and supported by a UE by using the IE idleModeMobility-
OP D-00201 Re- ControlInfo in an RRC Connection Release message
803 selection to the UE. If no related SPID configuration is
LST specified and this parameter is not set, a UE uses the
UTRAN LOFD-0 RAN common cell reselection priority of the neighboring
NFREQ 01036 Sharing UTRAN frequency, which is broadcast in the system
SCELL with information. This parameter applies only to LTE FDD
OP Commo and LTE TDD.
n
Carrier GUI Value Range: 0~7
Unit: None
Actual Value Range: 0~7
Default Value: 0

GeranN CellRes ADD LOFD-0 MOCN Meaning: Indicates the cell reselection dedicated
FGroup elDediPr GERAN 01112 / Flexible priority for a GERAN frequency carrier group based
SCellOp i NFGRO TDLOF Priority on the PLMN ID of the local cell. The value 0
UPSCE D-00111 Based indicates the lowest priority. If the related SPID
LLOP 2 Campin configuration is specified, set this priority to the one
MOD LBFD-0 g specified in the SPID configuration. If no related
GERAN 0201803 Cell SPID configuration is specified but this parameter is
NFGRO / Selectio set, the eNodeB delivers the cell reselection priorities
UPSCE TDLBF n and of all PLMNs supported by a UE by using the IE
LLOP D-00201 Re- idleModeMobilityControlInfo in an RRC Connection
803 selection Release message to the UE. If no related SPID
LST configuration is specified and this parameter is not set,
GERAN LOFD-0 RAN a UE uses the cell reselection priority of the
NFGRO 01036 / Sharing neighboring GERAN carrier frequency group, which
UPSCE TDLOF with is broadcast in the system information. This parameter
LLOP D-00103 Commo applies only to LTE FDD and LTE TDD.
6 n
Carrier GUI Value Range: 0~7
Unit: None
Actual Value Range: 0~7
Default Value: 0

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 91


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

Cdma20 Cdma1 ADD LOFD-0 CS Meaning: Indicates the dedicated cell reselection
00BcSC XrttCell CDMA2 01035 / Fallback priority for a CDMA2000 1xRTT band class based on
ellOp ReselDe 000BCS TDLOF to the PLMN ID of the local cell. The value 0 indicates
diPri CELLO D-00103 CDMA2 the lowest priority. If the related SPID configuration is
P 5 000 specified, set this priority to the one specified in the
MOD TDLBF 1xRTT SPID configuration. If no related SPID configuration
CDMA2 D-00101 S1-flex is specified but this parameter is set, the eNodeB
000BCS 8 delivers the cell reselection priorities of all PLMNs
Cell supported by a UE by using the IE idleModeMobility-
CELLO LBFD-0 Selectio
P ControlInfo in an RRC Connection Release message
0201803 n and to the UE. If no related SPID configuration is
LST / Re- specified and this parameter is not set, a UE uses the
CDMA2 TDLBF selection cell reselection priority of the CDMA2000 band class,
000BCS D-00201 RAN which is broadcast in the system information. This
CELLO 803 Sharing parameter applies only to LTE FDD and LTE TDD.
P LOFD-0 with GUI Value Range: 0~7
01036 / Commo
TDLOF n Unit: None
D-00103 Carrier Actual Value Range: 0~7
6 MOCN Default Value: 0
LOFD-0 Flexible
01112 / Priority
TDLOF Based
D-00111 Campin
2 g

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 92


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

Cdma20 HrpdCel ADD LOFD-0 PS Inter- Meaning: Indicates the dedicated cell reselection
00BcSC lReselD CDMA2 01021 / RAT priority for a CDMA2000 HRPD band class based on
ellOp ediPri 000BCS TDLOF Mobility the PLMN ID of the local cell. The value 0 indicates
CELLO D-00102 between the lowest priority. If the related SPID configuration is
P 1 E- specified, set this priority to the one specified in the
MOD LOFD-0 UTRAN SPID configuration. If no related SPID configuration
CDMA2 01112 / and is specified but this parameter is set, the eNodeB
000BCS TDLOF CDMA2 delivers the cell reselection priorities of all PLMNs
CELLO D-00111 000 supported by a UE by using the IE idleModeMobility-
P 2 MOCN ControlInfo in an RRC Connection Release message
Flexible to the UE. If no related SPID configuration is
LST LBFD-0 specified and this parameter is not set, a UE uses the
CDMA2 0201803 Priority
Based cell reselection priority of the CDMA2000 band class,
000BCS / which is broadcast in the system information. This
CELLO TDLBF Campin
g parameter applies only to LTE FDD and LTE TDD.
P D-00201
803 Cell GUI Value Range: 0~7
LOFD-0 Selectio Unit: None
01036 / n and Actual Value Range: 0~7
TDLOF Re-
selection Default Value: 0
D-00103
6 RAN
Sharing
with
Commo
n
Carrier

CellAlg Reselec MOD LBFD-0 Cell Meaning: Indicates whether to enable or disable
oSwitch PriAdap CELLA 0201803 Selectio adaptive dedicated cell reselection priority. If this
tSwitch LGOSW / n and switch is turned on, the eNodeB delivers the dedicated
ITCH TDLBF Re- cell reselection priority to a UE when the following
LST D-00201 selection conditions are met: (1) The UE requests to set up an
CELLA 803 RRC connection with the cause value being mo-
LGOSW Signalling. (2) The MME instructs the eNodeB to
ITCH release the S1 bearer. (3) The eNodeB fails to obtain
the UE capability. If this switch is turned off, the
eNodeB does not deliver dedicated cell reselection
priority to a UE even if the eNodeB fails to obtain the
UE capability information. This parameter applies
only to LTE FDD and LTE TDD.
GUI Value Range: OFF(Off), ON(On)
Unit: None
Actual Value Range: OFF, ON
Default Value: OFF(Off)

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 93


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

RrcCon T320For MOD LBFD-0 Cell Meaning:


nStateTi LoadBal RRCCO 0201803 Selectio Indicates the length of the timer T320 for load
mer ance NNSTA / n and balancing. T320 specifies the time period during
TETIM TDLBF Re- which the dedicated priorities (used for cell
ER D-00201 selection reselection) retain valid. The time period is contained
LST 803 Intra- in the RRCConnectionRelease message that is
RRCCO TDLOF LTE received by the UE. After T320 expires, the dedicated
NNSTA D-00103 Load priorities become invalid.
TETIM 2 Balancin
ER g This timer starts when the UE receives an
LOFD-0 RRCConnectionRelease message containing the t320
01044 Inter- IE. This timer stops when the UE enters the
LOFD-0 RAT RRC_CONNECTED mode. This parameter applies
70215 / Load only to LTE FDD and LTE TDD.
TDLOF Sharing
to GUI Value Range: min5(5), min10(10), min20(20),
D-07021 min30(30), min60(60), min120(120), min180(180)
5 UTRAN
Intra- Unit: min
LTE Actual Value Range: min5, min10, min20, min30,
User min60, min120, min180
Number Default Value: min10(10)
Load
Balancin
g

RrcCon T320For MOD LBFD-0 Cell Meaning: Indicates the length of the timer T320 to be
nStateTi Other RRCCO 0201803 Selectio contained in RRCConnectionRelease messages sent
mer NNSTA / n and for reasons other than load balancing. T320 specifies
TETIM TDLBF Re- the time period during which the dedicated priorities
ER D-00201 selection (used for cell reselection) are valid. After T320
LST 803 expires, the dedicated priorities become invalid. This
RRCCO parameter is invalid for UEs to be redirected based on
NNSTA the subscriber profile ID (SPID). This timer starts
TETIM when the UE receives an RRCConnectionRelease
ER message containing the t320 IE and stops when the
UE enters the RRC_CONNECTED mode. This
parameter applies only to LTE FDD and LTE TDD.
GUI Value Range: min5(5), min10(10), min20(20),
min30(30), min60(60), min120(120), min180(180)
Unit: min
Actual Value Range: min5, min10, min20, min30,
min60, min120, min180
Default Value: min120(120)

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 94


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

IntraFre PhyCellI ADD LBFD-0 Broadca Meaning: Indicates the starting physical cell ID of the
qBlkCel d INTRA 02009 / st of intra-frequency blacklisted cell. For details, see 3GPP
l FREQB TDLBF system TS 36.331. This parameter applies only to LTE FDD
LKCEL D-00200 informat and LTE TDD.
L 9 ion GUI Value Range: 0~503
LST LBFD-0 Coverag Unit: None
INTRA 0201801 e Based
FREQB / Intra- Actual Value Range: 0~503
LKCEL TDLBF frequenc Default Value: None
L D-00201 y
MOD 801 Handov
INTRA er
FREQB
LKCEL
L
RMV
INTRA
FREQB
LKCEL
L

IntraFre PhyCellI ADD LBFD-0 Broadca Meaning: Indicates the physical cell ID range of the
qBlkCel dRange INTRA 02009 / st of intra-frequency blacklisted cell. For details, see 3GPP
l FREQB TDLBF system TS 36.331. This parameter applies only to LTE FDD
LKCEL D-00200 informat and LTE TDD.
L 9 ion GUI Value Range: n1(n1), n4(n4), n8(n8), n12(n12),
MOD LBFD-0 Coverag n16(n16), n24(n24), n32(n32), n48(n48), n64(n64),
INTRA 0201801 e Based n84(n84), n96(n96), n128(n128), n168(n168),
FREQB / Intra- n252(n252), n504(n504)
LKCEL TDLBF frequenc Unit: None
L D-00201 y
801 Handov Actual Value Range: n1, n4, n8, n12, n16, n24, n32,
LST n48, n64, n84, n96, n128, n168, n252, n504
INTRA er
FREQB Default Value: n1(n1)
LKCEL
L

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 95


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

InterFre DlEarfc ADD LBFD-0 Cell Meaning: Indicates the DL EARFCN of the inter-
qBlkCel n INTERF 0201803 Selectio frequency blacklisted cell. For details, see 3GPP TS
l REQBL / n and 36.104. This parameter applies only to LTE FDD and
KCELL TDLBF Reselect LTE TDD.
LST D-00201 ion GUI Value Range: 0~68485
INTERF 803 Coverag Unit: None
REQBL LBFD-0 e Based
KCELL 0201802 Inter- Actual Value Range: 0~68485

MOD / frequenc Default Value: None


INTERF TDLBF y
REQBL D-00201 Handov
KCELL 802 er
RMV
INTERF
REQBL
KCELL

InterFre PhyCellI ADD LBFD-0 Coverag Meaning: Indicates the starting physical cell ID of the
qBlkCel d INTERF 0201802 e Based inter-frequency blacklisted cell. For details, see 3GPP
l REQBL / Inter- TS 36.331. This parameter applies only to LTE FDD
KCELL TDLBF frequenc and LTE TDD.
LST D-00201 y GUI Value Range: 0~503
INTERF 802 Handov
er Unit: None
REQBL LBFD-0
KCELL 0201804 Distance Actual Value Range: 0~503

MOD / Based Default Value: None


INTERF TDLBF Inter-
REQBL D-00201 frequenc
KCELL 804 y
LBFD-0 Handov
RMV er
INTERF 0201805
REQBL / Service
KCELL TDLBF Based
D-00201 Inter-
805 frequenc
y
Handov
er

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 96


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

InterFre PhyCellI ADD LBFD-0 Coverag Meaning: Indicates the physical cell ID range of the
qBlkCel dRange INTERF 0201802 e Based inter-frequency blacklisted cell. For details, see 3GPP
l REQBL / Inter- TS 36.331. This parameter applies only to LTE FDD
KCELL TDLBF frequenc and LTE TDD.
MOD D-00201 y GUI Value Range: n1(n1), n4(n4), n8(n8), n12(n12),
INTERF 802 Handov n16(n16), n24(n24), n32(n32), n48(n48), n64(n64),
REQBL LBFD-0 er n84(n84), n96(n96), n128(n128), n168(n168),
KCELL 0201804 Distance n252(n252), n504(n504)
LST / Based Unit: None
INTERF TDLBF Inter-
D-00201 frequenc Actual Value Range: n1, n4, n8, n12, n16, n24, n32,
REQBL n48, n64, n84, n96, n128, n168, n252, n504
KCELL 804 y
LBFD-0 Handov Default Value: n1(n1)
0201805 er
/ Service
TDLBF Based
D-00201 Inter-
805 frequenc
LBFD-0 y
0201803 Handov
er
Cell
Selectio
n and
Re-
selection

CellRes SIntraSe MOD LBFD-0 Cell Meaning: Indicates whether to set the measurement
el archCfgI CELLR 0201803 Selectio triggering threshold for reselection to intra-frequency
nd ESEL / n and cells.
LST TDLBF Re- GUI Value Range: NOT_CFG(Not configure),
CELLR D-00201 selection CFG(Configure)
ESEL 803 / Broadca
MLBFD Unit: None
st of
-120002 system Actual Value Range: NOT_CFG, CFG
37 informat Default Value: CFG(Configure)
LBFD-0 ion
02009 /
TDLBF
D-00200
9/
MLBFD
-120002
29

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 97


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes QQualM MOD LBFD-0 Broadca Meaning: Indicates whether to set cell reselection
el inCfgIn CELLR 02009 / st of parameters in compliance with 3GPP Release 9 in
d ESEL TDLBF system SIB3. This parameter applies only to LTE FDD and
LST D-00200 informat LTE TDD.
CELLR 9 ion GUI Value Range: NOT_CFG(Not configure),
ESEL LBFD-0 Cell CFG(Configure)
0201803 Selectio Unit: None
/ n and
TDLBF Re- Actual Value Range: NOT_CFG, CFG
D-00201 selection Default Value: CFG(Configure)
803

CellRes SIntraSe MOD LBFD-0 Cell Meaning:


el arch CELLR 0201803 Selectio Indicates the measurement triggering threshold for
ESEL / n and reselection to intra-frequency cells.
LST TDLBF Re-
CELLR D-00201 selection The UEs start intra-frequency measurements only if
ESEL 803 / Broadca the value of Cell selection RX level value (dB) is
MLBFD st of lower than or equal to the value of this parameter.
-120002 system GUI Value Range: 0~31
37 informat Unit: 2dB
LBFD-0 ion
02009 / Actual Value Range: 0~62
TDLBF Default Value: 29
D-00200
9/
MLBFD
-120002
29

CellRes SIntraSe MOD LBFD-0 Broadca Meaning: Indicates the RSRQ threshold for starting
el archQ CELLR 02009 / st of intra-frequency measurements. It determines the
ESEL TDLBF system probability of triggering cell reselection to an intra-
LST D-00200 informat frequency neighboring cell. For details, see 3GPP TS
CELLR 9 ion 36.304. This parameter applies only to LTE FDD and
ESEL LBFD-0 Cell LTE TDD.
0201803 Selectio GUI Value Range: 0~31
/ n and Unit: dB
TDLBF Re-
D-00201 selection Actual Value Range: 0~31
803 Default Value: 5

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 98


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes SNonInt MOD LBFD-0 Cell Meaning: Indicates whether to configure the
el raSearch CELLR 0201803 Selectio measurement triggering threshold for cell reselection
CfgInd ESEL / n and to inter-frequency or inter-RAT cells. If this parameter
LST TDLBF Re- is set to NOT_CFG and the QQualMinCfgInd
CELLR D-00201 selection parameter is set to NOT_CFG, the UE continuously
ESEL 803 / Broadca measures intra-frequency and inter-RAT cells,
MLBFD st of regardless of the signal quality of the serving cell.
-120002 system GUI Value Range: NOT_CFG(Not configure),
37 informat CFG(Configure)
LBFD-0 ion Unit: None
02009 / PS Inter-
TDLBF Actual Value Range: NOT_CFG, CFG
RAT
D-00200 Mobility Default Value: CFG(Configure)
9/ between
MLBFD E-
-120002 UTRAN
29 and
LOFD-0 CDMA2
01021 / 000
TDLOF PS
D-00102 Mobility
1 from E-
LOFD-0 UTRAN
01111 to
CDMA2
000
HRPD
Based
on
Frequen
cy-
specific
Factors

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 99


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes SNonInt MOD LBFD-0 Cell Meaning: Indicates the measurement triggering
el raSearch CELLR 0201803 Selectio threshold for reselection to inter-frequency or inter-
ESEL / n and RAT cells. If the cell reselection priority of a
LST TDLBF Re- frequency or RAT is higher than that of the serving
CELLR D-00201 selection frequency, the UEs always start inter-frequency or
ESEL 803 / Broadca inter-RAT measurements. If the cell reselection
MLBFD st of priority of a frequency is lower than or equal to that of
-120002 system the serving frequency or if the cell reselection priority
37 informat of an RAT is lower than that of the serving frequency,
LBFD-0 ion the UEs start inter-frequency or inter-RAT
02009 / measurements only when the value of Cell selection
PS Inter- RX level value (dB) is lower than or equal to the value
TDLBF RAT
D-00200 of this parameter.
Mobility
9/ between GUI Value Range: 0~31
MLBFD E- Unit: 2dB
-120002 UTRAN
29 Actual Value Range: 0~62
and
LOFD-0 CDMA2 Default Value: 9
01021 / 000
TDLOF PS
D-00102 Mobility
1 from E-
LOFD-0 UTRAN
01111 to
CDMA2
000
HRPD
Based
on
Frequen
cy-
specific
Factors

CellRes SNonInt MOD LBFD-0 Broadca Meaning: Indicates the RSRQ threshold for starting
el raSearch CELLR 02009 / st of inter-frequency or inter-RAT measurements. It
Q ESEL TDLBF system determines the probability of triggering cell
LST D-00200 informat reselection to an inter-frequency or inter-RAT
CELLR 9 ion neighboring cell. For details, see 3GPP TS 36.304.
ESEL LBFD-0 Cell This parameter applies only to LTE FDD and LTE
0201803 Selectio TDD.
/ n and GUI Value Range: 0~31
TDLBF Re- Unit: dB
D-00201 selection
803 Actual Value Range: 0~31
Default Value: 4

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 100


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes QRxLev MOD LBFD-0 Cell Meaning: Indicates the minimum required RX level
el Min CELLR 0201803 Selectio used in intra-frequency E-UTRAN cell reselection,
ESEL / n and which corresponds to the IE q-RxLevMin in SIB3.
LST TDLBF Re- This value is included in the cell reselection criteria
CELLR D-00201 selection and used in the evaluation of cell reselection. For
ESEL 803 / Broadca details, see 3GPP TS 36.304.
MLBFD st of GUI Value Range: -70~-22
-120002 system
37 Unit: 2dBm
informat
LBFD-0 ion Actual Value Range: -140~-44
02009 / PS Inter- Default Value: -64
TDLBF RAT
D-00200 Mobility
9/ between
MLBFD E-
-120002 UTRAN
29 and
LOFD-0 CDMA2
01021 / 000
TDLOF PS
D-00102 Mobility
1 from E-
LOFD-0 UTRAN
01111 to
CDMA2
000
HRPD
Based
on
Frequen
cy-
specific
Factors

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 101


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes PMax MOD LBFD-0 Cell Meaning: Indicates the maximum power that the UE
el CELLR 0201803 Selectio can apply to transmission in the intra-frequency
ESEL / n and neighboring cell. It is used in cell reselection criteria
LST TDLBF Re- to calculate the compensated power. If the value of
CELLR D-00201 selection this parameter is not specified, the maximum power is
ESEL 803 / Broadca subject to the UE capability. For details, see 3GPP TS
MLBFD st of 36.304.
-120002 system GUI Value Range: -30~33
37 informat Unit: dBm
LBFD-0 ion
02009 / Actual Value Range: -30~33
TDLBF Default Value: 23
D-00200
9/
MLBFD
-120002
29

CellRes QQualM MOD LBFD-0 Broadca Meaning: Indicates the minimum required RX signal
el in CELLR 02009 / st of quality used in intra-frequency E-UTRAN cell
ESEL TDLBF system reselection, which corresponds to the IE q-QualMin in
LST D-00200 informat SIB3. This value is included in criteria R and used in
CELLR 9 ion the evaluation of cell reselection. For details, see
ESEL LBFD-0 Cell 3GPP TS 36.304. This parameter applies only to LTE
0201803 Selectio FDD and LTE TDD.
/ n and GUI Value Range: -34~-3
TDLBF Re- Unit: dB
D-00201 selection
803 Actual Value Range: -34~-3
Default Value: -18

EutranIn QRxLev ADD LBFD-0 Cell Meaning: Indicates the RX level required for a
terNFre Min EUTRA 0201803 Selectio neighboring cell on the frequency to become a
q NINTE / n and suitable cell for selection. It is included in criteria S
RNFRE TDLBF Reselect and used in the evaluation for cell selection. During
Q D-00201 ion the evaluation for cell reselection, the UE performs
MOD 803 / the following calculation: Srxlev = Measured RSRP
EUTRA MLBFD value of a neighboring cell on the frequency - Value of
NINTE -120002 this parameter - Compensated power. If Srxlev for a
RNFRE 37 cell is better than a threshold for a time-to-trigger,
Q reselection to the cell is started. For details, see 3GPP
TS 36.304.
LST
EUTRA GUI Value Range: -70~-22
NINTE Unit: 2dBm
RNFRE Actual Value Range: -140~-44
Q
Default Value: -64

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 102


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

EutranIn Pmax ADD LBFD-0 Cell Meaning: Indicates the maximum power that the UE
terNFre EUTRA 0201803 Selectio can apply to transmission on the neighboring E-
q NINTE / n and UTRAN frequency. It is used in cell reselection
RNFRE TDLBF Reselect criteria to calculate the compensated power. If the
Q D-00201 ion value of this parameter is not specified, the maximum
MOD 803 / power is subject to the UE capability. For details, see
EUTRA MLBFD 3GPP TS 36.304.
NINTE -120002 GUI Value Range: -30~33
RNFRE 37
Unit: dBm
Q
Actual Value Range: -30~33
LST
EUTRA Default Value: 23
NINTE
RNFRE
Q

EutranIn QqualM ADD LBFD-0 Cell Meaning: Indicates the minimum RX level of an inter-
terNFre in EUTRA 0201803 Selectio frequency neighboring cell, which is required for it to
q NINTE / n and become a candidate for cell reselection. It determines
RNFRE TDLBF Re- the probability of triggering cell reselection to inter-
Q D-00201 selection frequency neighboring cells on the frequency. The
MOD 803 value of this parameter is contained in SIB5. For
EUTRA details, see 3GPP TS 36.331. This parameter applies
NINTE only to LTE FDD and LTE TDD.
RNFRE GUI Value Range: -34~-3
Q Unit: dB
LST Actual Value Range: -34~-3
EUTRA
NINTE Default Value: -18
RNFRE
Q

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 103


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes TReselE MOD LBFD-0 Cell Meaning: Indicates the evaluation period for a UE to
el utran CELLR 0201803 Selectio determine whether to perform cell reselections to a
ESEL / n and new E-UTRAN cell. If the signal quality of a new E-
LST TDLBF Re- UTRAN cell is better than that of the serving cell
CELLR D-00201 selection within the period specified by this parameter and a UE
ESEL 803 Broadca camps on the serving cell for more than 1s, the UE
LBFD-0 st of initiates cell reselections to the new E-UTRAN cell.
02009 / system This parameter applies only to LTE FDD and LTE
TDLBF informat TDD.
D-00200 ion GUI Value Range: 0~7
9 MOCN Unit: s
LOFD-0 Flexible Actual Value Range: 0~7
01112 / Priority
TDLOF Based Default Value: 1
D-00111 Campin
2 g

EutranIn EutranR ADD LBFD-0 Cell Meaning: Indicates the evaluation duration for a UE to
terNFre eselTim EUTRA 0201803 Selectio determine whether to reselect the inter-frequency
q e NINTE / n and neighboring cell to camp on. If the signal quality in an
RNFRE TDLBF Re- inter-frequency neighboring cell is better than that in
Q D-00201 selection the serving cell for the period specified by this
MOD 803 parameter and a UE camps on the serving cell for
EUTRA more than 1s, the UE attempts to reselect the inter-
NINTE frequency neighboring cell to camp on. This
RNFRE parameter is contained in SIB5. For details, see 3GPP
Q TS 36.331. This parameter applies only to LTE FDD
and LTE TDD.
LST
EUTRA GUI Value Range: 0~7
NINTE Unit: s
RNFRE Actual Value Range: 0~7
Q
Default Value: 1

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 104


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes Qhyst MOD LBFD-0 Cell Meaning: Indicates the hysteresis for cell reselection
el CELLR 0201803 Selectio when RSRP values are used in the evaluation. This
ESEL / n and parameter must be set based on the slow fading
LST TDLBF Re- characteristic of the area covered by the cell. The
CELLR D-00201 selection greater the slow fading variance is, the larger the value
ESEL 803 / Broadca of this parameter must be set to. A larger value of the
MLBFD st of hysteresis results in a larger boundary of the serving
-120002 system cell and a lower probability of cell reselection to
37 informat neighboring cells.
LBFD-0 ion GUI Value Range: DB0_Q_HYST(0dB),
02009 / DB1_Q_HYST(1dB), DB2_Q_HYST(2dB),
TDLBF DB3_Q_HYST(3dB), DB4_Q_HYST(4dB),
D-00200 DB5_Q_HYST(5dB), DB6_Q_HYST(6dB),
9/ DB8_Q_HYST(8dB), DB10_Q_HYST(10dB),
MLBFD DB12_Q_HYST(12dB), DB14_Q_HYST(14dB),
-120002 DB16_Q_HYST(16dB), DB18_Q_HYST(18dB),
29 DB20_Q_HYST(20dB), DB22_Q_HYST(22dB),
DB24_Q_HYST(24dB)
Unit: dB
Actual Value Range: DB0_Q_HYST, DB1_Q_HYST,
DB2_Q_HYST, DB3_Q_HYST, DB4_Q_HYST,
DB5_Q_HYST, DB6_Q_HYST, DB8_Q_HYST,
DB10_Q_HYST, DB12_Q_HYST, DB14_Q_HYST,
DB16_Q_HYST, DB18_Q_HYST, DB20_Q_HYST,
DB22_Q_HYST, DB24_Q_HYST
Default Value: DB4_Q_HYST(4dB)

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 105


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

EutranIn CellQoff ADD LBFD-0 Coverag Meaning: Indicates the offset for the intra-frequency
traFreq set EUTRA 0201801 e Based neighboring cell, which is used in evaluation for cell
NCell NINTR / Intra- reselections. A larger value of this parameter results in
AFREQ TDLBF frequenc a lower probability of cell reselections to this
NCELL D-00201 y neighboring cell. If this parameter is not set to dB0, it
MOD 801 Handov is delivered in SIB4. For details, see 3GPP TS 36.331.
EUTRA LBFD-0 er If this parameter is set to dB0, it is not delivered in
NINTR 0201803 Cell SIB4. In this situation, UEs use 0 dB as the offset for
AFREQ Selectio cell reselections. For details, see 3GPP TS 36.304.
NCELL n and GUI Value Range: dB-24(-24dB), dB-22(-22dB),
LST Re- dB-20(-20dB), dB-18(-18dB), dB-16(-16dB),
EUTRA selection dB-14(-14dB), dB-12(-12dB), dB-10(-10dB),
NINTR dB-8(-8dB), dB-6(-6dB), dB-5(-5dB), dB-4(-4dB),
AFREQ dB-3(-3dB), dB-2(-2dB), dB-1(-1dB), dB0(0dB),
NCELL dB1(1dB), dB2(2dB), dB3(3dB), dB4(4dB),
dB5(5dB), dB6(6dB), dB8(8dB), dB10(10dB),
dB12(12dB), dB14(14dB), dB16(16dB), dB18(18dB),
dB20(20dB), dB22(22dB), dB24(24dB)
Unit: dB
Actual Value Range: dB-24, dB-22, dB-20, dB-18,
dB-16, dB-14, dB-12, dB-10, dB-8, dB-6, dB-5, dB-4,
dB-3, dB-2, dB-1, dB0, dB1, dB2, dB3, dB4, dB5,
dB6, dB8, dB10, dB12, dB14, dB16, dB18, dB20,
dB22, dB24
Default Value: dB0(0dB)

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 106


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

EutranIn CellQoff ADD LBFD-0 Cell Meaning: Indicates the offset for the inter-frequency
terFreq set EUTRA 0201803 Selectio neighboring cell, which is used in evaluation for cell
NCell NINTE / n and reselections. A larger value of this parameter results in
RFREQ TDLBF Re- a lower probability of cell reselections to this
NCELL D-00201 selection neighboring cell. If this parameter is not set to dB0, it
MOD 803 is delivered in SIB5. For details, see 3GPP TS 36.331.
EUTRA If this parameter is set to dB0, it is not delivered in
NINTE SIB5. In this situation, UEs use 0 dB as the offset for
RFREQ cell reselections. For details, see 3GPP TS 36.304.
NCELL This parameter applies only to LTE FDD and LTE
TDD.
LST
EUTRA GUI Value Range: dB-24(-24dB), dB-22(-22dB),
NINTE dB-20(-20dB), dB-18(-18dB), dB-16(-16dB),
RFREQ dB-14(-14dB), dB-12(-12dB), dB-10(-10dB),
NCELL dB-8(-8dB), dB-6(-6dB), dB-5(-5dB), dB-4(-4dB),
dB-3(-3dB), dB-2(-2dB), dB-1(-1dB), dB0(0dB),
dB1(1dB), dB2(2dB), dB3(3dB), dB4(4dB),
dB5(5dB), dB6(6dB), dB8(8dB), dB10(10dB),
dB12(12dB), dB14(14dB), dB16(16dB), dB18(18dB),
dB20(20dB), dB22(22dB), dB24(24dB)
Unit: dB
Actual Value Range: dB-24, dB-22, dB-20, dB-18,
dB-16, dB-14, dB-12, dB-10, dB-8, dB-6, dB-5, dB-4,
dB-3, dB-2, dB-1, dB0, dB1, dB2, dB3, dB4, dB5,
dB6, dB8, dB10, dB12, dB14, dB16, dB18, dB20,
dB22, dB24
Default Value: dB0(0dB)

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 107


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

EutranIn QoffsetF ADD LBFD-0 Cell Meaning: Indicates the frequency-specific offset for
terNFre req EUTRA 0201803 Selectio the neighboring E-UTRAN frequency that applies to
q NINTE / n and UEs in idle mode. It is contained in system
RNFRE TDLBF Re- information block type 5 (SIB5) and delivered to UEs
Q D-00201 selection in idle mode for cell reselection. For details, see 3GPP
MOD 803 / TS 36.331.
EUTRA MLBFD GUI Value Range: dB-24(-24dB), dB-22(-22dB),
NINTE -120002 dB-20(-20dB), dB-18(-18dB), dB-16(-16dB),
RNFRE 37 dB-14(-14dB), dB-12(-12dB), dB-10(-10dB),
Q dB-8(-8dB), dB-6(-6dB), dB-5(-5dB), dB-4(-4dB),
LST dB-3(-3dB), dB-2(-2dB), dB-1(-1dB), dB0(0dB),
EUTRA dB1(1dB), dB2(2dB), dB3(3dB), dB4(4dB),
NINTE dB5(5dB), dB6(6dB), dB8(8dB), dB10(10dB),
RNFRE dB12(12dB), dB14(14dB), dB16(16dB), dB18(18dB),
Q dB20(20dB), dB22(22dB), dB24(24dB)
Unit: dB
Actual Value Range: dB-24, dB-22, dB-20, dB-18,
dB-16, dB-14, dB-12, dB-10, dB-8, dB-6, dB-5, dB-4,
dB-3, dB-2, dB-1, dB0, dB1, dB2, dB3, dB4, dB5,
dB6, dB8, dB10, dB12, dB14, dB16, dB18, dB20,
dB22, dB24
Default Value: dB0(0dB)

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 108


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

EutranIn CellMea ADD LBFD-0 Coverag Meaning: Indicates the priority of measurement on the
traFreq sPriority EUTRA 0201801 e Based intra-frequency neighboring cell. The eNodeB
NCell NINTR / Intra- preferentially contains the information about a
AFREQ TDLBF frequenc neighboring cell with this priority set to
NCELL D-00201 y HIGH_PRIORITY while delivering a measurement
MOD 801 Handov configuration. This parameter applies only to LTE
EUTRA LBFD-0 er FDD and LTE TDD.
NINTR 0201804 Distance GUI Value Range: LOW_PRIORITY(Low Priority),
AFREQ / Based HIGH_PRIORITY(High Priority)
NCELL TDLBF Inter- Unit: None
LST D-00201 frequenc
804 y Actual Value Range: LOW_PRIORITY,
EUTRA HIGH_PRIORITY
NINTR LBFD-0 Handov
AFREQ 0201805 er Default Value: LOW_PRIORITY(Low Priority)
NCELL / Service
TDLBF Based
D-00201 Inter-
805 frequenc
LBFD-0 y
0201803 Handov
er
Cell
Selectio
n and
Re-
selection

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 109


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

EutranIn CellMea ADD LBFD-0 Coverag Meaning: Indicates the priority of measurement on the
terFreq sPriority EUTRA 0201802 e Based inter-frequency neighboring cell. The eNodeB
NCell NINTE / Inter- preferentially contains the information about a
RFREQ TDLBF frequenc neighboring cell with this priority set to
NCELL D-00201 y HIGH_PRIORITY while delivering a measurement
MOD 802 Handov configuration. This parameter applies only to LTE
EUTRA LBFD-0 er FDD and LTE TDD.
NINTE 0201804 Distance GUI Value Range: LOW_PRIORITY(Low Priority),
RFREQ / Based HIGH_PRIORITY(High Priority)
NCELL TDLBF Inter- Unit: None
LST D-00201 frequenc
804 y Actual Value Range: LOW_PRIORITY,
EUTRA HIGH_PRIORITY
NINTE LBFD-0 Handov
RFREQ 0201805 er Default Value: LOW_PRIORITY(Low Priority)
NCELL / Service
TDLBF Based
D-00201 Inter-
805 frequenc
TDLOF y
D-00105 Handov
0 er
LBFD-0 Mobility
0201803 between
LTE
TDD
and LTE
FDD
Cell
Selectio
n and
Reselect
ion /
Cell
Selectio
n and
Re-
selection

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 110


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

UtranNF QRxLev ADD LBFD-0 Cell Meaning: Indicates the RX level required for a
req Min UTRAN 0201803 Selectio neighboring cell on the UTRAN frequency to become
NFREQ / n and a candidate for selection. It is included in criteria S
MOD TDLBF Reselect and used in the evaluation for cell selection. During
UTRAN D-00201 ion / the evaluation for cell reselection, the UE performs
NFREQ 803 Cell the following calculation: Srxlev = Measured RSCP
Selectio value of a neighboring cell on the frequency - Value of
LST n and this parameter - Compensated power. If Srxlev for a
UTRAN Re- neighboring cell is better than a threshold for a time-
NFREQ selection to-trigger, reselection to the cell is started. For details,
see 3GPP TS 25.304. This parameter applies only to
LTE FDD and LTE TDD.
GUI Value Range: -60~-13
Unit: 2dBm
Actual Value Range: -119~-25
Default Value: -58

UtranNF Qqualmi ADD LBFD-0 Cell Meaning: Indicates the minimum quality level
req n UTRAN 0201803 Selectio required for a cell on the UTRAN frequency to
NFREQ / n and become a candidate for reselection. A neighboring cell
MOD TDLBF Reselect on the UTRAN frequency can become a candidate for
UTRAN D-00201 ion / reselection only when the signal quality of the cell is
NFREQ 803 Cell better than the value of this parameter. For details, see
Selectio 3GPP TS 25.304. This parameter applies only to LTE
LST n and FDD.
UTRAN Re-
NFREQ GUI Value Range: -24~0
selection
Unit: dB
Actual Value Range: -24~0
Default Value: -22

UtranNF PmaxUt ADD LBFD-0 Cell Meaning: Indicates the maximum power that the UE
req ran UTRAN 0201803 Selectio can apply to transmission on the UTRAN frequency. It
NFREQ / n and is used in criteria S to calculate the compensated
MOD TDLBF Reselect power. For details, see 3GPP TS 25.104. This
UTRAN D-00201 ion parameter applies only to LTE FDD and LTE TDD.
NFREQ 803 GUI Value Range: -50~33
LST Unit: dBm
UTRAN Actual Value Range: -50~33
NFREQ
Default Value: 24

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 111


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

GeranNf QRxLev ADD LBFD-0 Cell Meaning: Indicates the minimum GERAN signal level
reqGrou Min GERAN 0201803 Selectio required for cell reselection based on criteria S.
p NFREQ / n and Assume that: Srxlev = Measured RSSI of a
GROUP TDLBF Reselect neighboring cell on a frequency in the GERAN carrier
MOD D-00201 ion frequency group - Actual value of this parameter -
GERAN 803 Compensated power. If Srxlev is consistently greater
NFREQ than a specific threshold for cell reselection, the UE
GROUP reselects this neighboring cell. For details, see 3GPP
TS 36.104. Note: Actual value of this parameter =
LST -115 + 2 x GUI value of this parameter This parameter
GERAN applies only to LTE FDD and LTE TDD.
NFREQ
GROUP GUI Value Range: 0~45
Unit: 2dBm
Actual Value Range: -115~-25
Default Value: 0

GeranNf PmaxGe ADD LBFD-0 Cell Meaning: Indicates the maximum power that the UE
reqGrou ran GERAN 0201803 Selectio can apply to transmission on a frequency in the
p NFREQ / n and GERAN carrier frequency group. It is used in cell
GROUP TDLBF Reselect reselection criteria to calculate the compensated
MOD D-00201 ion power. If the value of this parameter is not specified,
GERAN 803 the maximum power is subject to the UE capability.
NFREQ For details, see 3GPP TS 36.304. This parameter
GROUP applies only to LTE FDD and LTE TDD.
LST GUI Value Range: 0~39
GERAN Unit: dBm
NFREQ Actual Value Range: 0~39
GROUP
Default Value: 0

CellRes ThrshSe MOD LBFD-0 Broadca Meaning: Indicates the RSRQ threshold for cell
el rvLowQ CELLR 02009 / st of reselection to cells on lower-priority frequencies. It
ESEL TDLBF system determines the probability of triggering cell
LST D-00200 informat reselection to inter-frequency or inter-RAT
CELLR 9 ion neighboring cells on lower-priority frequencies. For
ESEL LBFD-0 Cell details, see 3GPP TS 36.304. This parameter applies
0201803 Selectio only to LTE FDD and LTE TDD.
/ n and GUI Value Range: 0~31
TDLBF Re- Unit: dB
D-00201 selection
803 Actual Value Range: 0~31
Default Value: 0

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 112


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

EutranIn ThreshX ADD LBFD-0 Cell Meaning:


terNFre highQ EUTRA 0201803 Selectio Indicates the RSRQ-based minimum RX level
q NINTE / n and required for a neighboring cell on the frequency to
RNFRE TDLBF Reselect become a candidate for reselection if the RSRQ-based
Q D-00201 ion / priority of the frequency is higher than that of the
MOD 803 Cell serving frequency.
EUTRA Selectio
NINTE n and After measurements are started for neighboring cells
RNFRE Re- on the neighboring E-UTRAN frequency, the UE
Q selection reselects to a neighboring cell on the frequency only if
the RSRQ-based RX level of the cell is higher than
LST the value specified by this parameter for a time-to-
EUTRA trigger. For details, see 3GPP TS 36.331. This
NINTE parameter applies only to LTE FDD and LTE TDD.
RNFRE
Q GUI Value Range: 0~31
Unit: dB
Actual Value Range: 0~31
Default Value: 0

UtranNF ThreshX ADD LBFD-0 Cell Meaning:


req HighQ UTRAN 0201803 Selectio Indicates the RSRQ-based minimum RX level
NFREQ / n and required for a neighboring cell on the frequency to
MOD TDLBF Reselect become a candidate for reselection if the RSRQ-based
UTRAN D-00201 ion / priority of the frequency is higher than that of the
NFREQ 803 Cell serving frequency.
Selectio
LST n and After measurements are started for neighboring cells
UTRAN Re- on the UTRAN frequency, the UE reselects to a
NFREQ selection neighboring cell on the frequency only if the RSRQ-
based RX level of the cell is higher than the value
specified by this parameter for a time-to-trigger. For
details, see 3GPP TS 36.331. This parameter applies
only to LTE FDD and LTE TDD.
GUI Value Range: 0~31
Unit: dB
Actual Value Range: 0~31
Default Value: 0

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 113


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes TReselU ADD LBFD-0 Broadca Meaning: Indicates the evaluation period for a UE to
elUtran tran CELLR 02009 / st of determine whether to reselect a neighboring UTRAN
ESELU TDLBF system cell to camp on. During the evaluation period, if the
TRAN D-00200 informat signal quality in a neighboring UTRAN cell is better
MOD 9 ion than that in the serving cell and a UE camps on the
CELLR LBFD-0 Cell serving cell for more than 1s, the UE attempts to
ESELU 0201803 Selectio reselect the neighboring UTRAN cell to camp on.
TRAN / n and This parameter applies only to LTE FDD and LTE
TDLBF Re- TDD.
LST
CELLR D-00201 selection GUI Value Range: 0~7
ESELU 803 MOCN Unit: s
TRAN LOFD-0 Flexible Actual Value Range: 0~7
01112 / Priority
TDLOF Based Default Value: 1
D-00111 Campin
2 g

UtranNF ThreshX ADD LBFD-0 Cell Meaning: Indicates the minimum RX level required
req High UTRAN 0201803 Selectio for a neighboring cell on the UTRAN frequency to
NFREQ / n and become a candidate for reselection if the priority of
MOD TDLBF Reselect the frequency is higher than that of the serving
UTRAN D-00201 ion frequency. After measurements are started for
NFREQ 803 neighboring cells on the UTRAN frequency, the UE
reselects to a neighboring cell on the frequency only if
LST the RX level of the cell is higher than the value
UTRAN specified by this parameter for a time-to-trigger. For
NFREQ details, see 3GPP TS 36.331. This parameter applies
only to LTE FDD and LTE TDD.
GUI Value Range: 0~31
Unit: 2dB
Actual Value Range: 0~62
Default Value: 6

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 114


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

GeranNf ThreshX ADD LBFD-0 Cell Meaning:


reqGrou High GERAN 0201803 Selectio Indicates the RX level required for a neighboring cell
p NFREQ / n and on a frequency in the GERAN carrier frequency group
GROUP TDLBF Reselect to become a candidate for reselection if the priority of
MOD D-00201 ion the frequency is higher than that of the serving
GERAN 803 frequency.
NFREQ
GROUP After measurements are started for neighboring cells
on a frequency in the GERAN carrier frequency
LST group, the UE reselects to a cell on the frequency only
GERAN if the RX level of the cell is better than the value
NFREQ specified by this parameter for a time-to-trigger. For
GROUP details, see 3GPP TS 36.104. This parameter applies
only to LTE FDD and LTE TDD.
GUI Value Range: 0~31
Unit: 2dB
Actual Value Range: 0~62
Default Value: 7

CellRes TReselG ADD LBFD-0 Cell Meaning: Indicates the evaluation period for a UE to
elGeran eran CELLR 0201803 Selectio determine whether to reselect a neighboring GERAN
ESELG / n and cell to camp on. During the evaluation period, if the
ERAN TDLBF Re- signal quality in a neighboring GERAN cell is better
MOD D-00201 selection than that in the serving cell and a UE camps on the
CELLR 803 Broadca serving cell for more than 1s, the UE attempts to
ESELG LBFD-0 st of reselect the neighboring GERAN cell to camp on.
ERAN 02009 / system This parameter applies only to LTE FDD and LTE
TDLBF informat TDD.
LST
CELLR D-00200 ion GUI Value Range: 0~7
ESELG 9 MOCN Unit: s
ERAN LOFD-0 Flexible Actual Value Range: 0~7
01112 / Priority
TDLOF Based Default Value: 1
D-00111 Campin
2 g

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 115


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

Cdma20 Cdma20 ADD LBFD-0 Cell Meaning: Indicates the RX signal level required for a
00Band 001Xrtt CDMA2 0201803 Selectio cell on a frequency in the higher-priority CDMA2000
Class ThreshX 000BA / n and 1xRTT band class to become a candidate for cell
High NDCLA TDLBF Re- reselection. After measurements are started for cells
SS D-00201 selection on a frequency in the band class, a cell on the
MOD 803 CS frequency can become a candidate for reselection only
CDMA2 LOFD-0 Fallback if the RX signal level of the cell is higher than the
000BA 01035 / to value specified by this parameter for a time-to-trigger.
NDCLA TDLOF CDMA2 For details, see section 5.2.4.5 in 3GPP TS 36.304.
SS D-00103 000 This parameter applies only to LTE FDD and LTE
5 1xRTT TDD.
LST
CDMA2 LOFD-0 Enhance GUI Value Range: -63~0
000BA 01090 / d CS Unit: 0.5dB
NDCLA TDLOF Fallback Actual Value Range: -31.5~0
SS D-00109 to
0 CDMA2 Default Value: -34
000
1xRTT

Cdma20 Cdma20 ADD LBFD-0 Cell Meaning: Indicates the RX signal level required for a
00Band 00Hrpd CDMA2 0201803 Selectio cell on a frequency in the higher-priority CDMA2000
Class ThreshX 000BA / n and HRPD band class to become a candidate for cell
High NDCLA TDLBF Re- reselection. After measurements are started for cells
SS D-00201 selection on a frequency in the band class, a cell on the
MOD 803 PS Inter- frequency can become a candidate for reselection only
CDMA2 LOFD-0 RAT if the RX signal level of the cell is higher than the
000BA 01021 / Mobility value specified by this parameter for a time-to-trigger.
NDCLA TDLOF between For details, see section 5.2.4.5 in 3GPP TS 36.304.
SS D-00102 E- This parameter applies only to LTE FDD and LTE
1 UTRAN TDD.
LST
CDMA2 LOFD-0 and GUI Value Range: -63~0
000BA 01111 CDMA2 Unit: 0.5dB
NDCLA 000
Actual Value Range: -31.5~0
SS PS
Mobility Default Value: -26
from E-
UTRAN
to
CDMA2
000
HRPD
Based
on
Frequen
cy-
specific
Factors

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 116


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes Cdma1 ADD LBFD-0 Cell Meaning: Indicates the evaluation period for a UE to
elCdma XrttTres CELLR 0201803 Selectio determine whether to reselect a neighboring
2000 election ESELC / n and CDMA2000 1xRTT cell to camp on. During the
DMA20 TDLBF Re- evaluation period, if the signal quality in a
00 D-00201 selection neighboring CDMA2000 1xRTT cell is better than
MOD 803 CS that in the serving cell and a UE camps on the serving
CELLR LOFD-0 Fallback cell for more than 1s, the UE attempts to reselect the
ESELC 01035 / to neighboring CDMA2000 1xRTT cell to camp on. For
DMA20 TDLOF CDMA2 details about this parameter, see 3GPP TS 36.331.
00 D-00103 000 This parameter applies only to LTE FDD and LTE
5 1xRTT TDD.
LST
CELLR LBFD-0 Broadca GUI Value Range: 0~7
ESELC 02009 / st of Unit: None
DMA20 TDLBF system Actual Value Range: 0~7
00 D-00200 informat
9 ion Default Value: 1

TDLOF Enhance
D-00109 d CS
0/ Fallback
LOFD-0 to
01090 CDMA2
LOFD-0 000
01112 / 1xRTT
TDLOF MOCN
D-00111 Flexible
2 Priority
Based
Campin
g

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 117


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes Treselec ADD LBFD-0 Cell Meaning: Indicates the evaluation period for a UE to
elCdma tionHrp CELLR 0201803 Selectio determine whether to reselect a neighboring
2000 d ESELC / n and CDMA2000 HRPD cell to camp on. During the
DMA20 TDLBF Re- evaluation period, if the signal quality in a
00 D-00201 selection neighboring CDMA2000 HRPD cell is better than that
MOD 803 PS Inter- in the serving cell and a UE camps on the serving cell
CELLR LOFD-0 RAT for more than 1s, the UE attempts to reselect the
ESELC 01021 / Mobility neighboring CDMA2000 HRPD cell to camp on. For
DMA20 TDLOF between details about this parameter, see 3GPP TS 36.331.
00 D-00102 E- This parameter applies only to LTE FDD and LTE
1 UTRAN TDD.
LST
CELLR LBFD-0 and GUI Value Range: 0~7
ESELC 02009 / CDMA2 Unit: s
DMA20 TDLBF 000
Actual Value Range: 0~7
00 D-00200 Broadca
9 st of Default Value: 1

LOFD-0 system
01112 / informat
TDLOF ion
D-00111 MOCN
2 Flexible
Priority
Based
Campin
g

EutranIn ThreshX ADD LBFD-0 Cell Meaning: Indicates the RX level required for a
terNFre high EUTRA 0201803 Selectio neighboring cell on the frequency to become a
q NINTE / n and candidate for reselection if the priority of the
RNFRE TDLBF Reselect frequency is higher than that of the serving frequency.
Q D-00201 ion After measurements are started for neighboring cells
MOD 803 on the frequency, the UE reselects to a neighboring
EUTRA cell on the frequency only if the RX level of the cell is
NINTE better than the value specified by this parameter for a
RNFRE time-to-trigger. For details, see 3GPP TS 36.331. This
Q parameter applies only to LTE FDD and LTE TDD.
LST GUI Value Range: 0~31
EUTRA Unit: 2dB
NINTE
Actual Value Range: 0~62
RNFRE
Q Default Value: 11

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 118


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

EutranIn ThreshX ADD LBFD-0 Cell Meaning: Indicates the RSRQ-based minimum RX
terNFre lowQ EUTRA 0201803 Selectio level required for a neighboring cell on the frequency
q NINTE / n and to become a candidate for reselection if the RSRQ-
RNFRE TDLBF Reselect based priority of the frequency is lower than that of
Q D-00201 ion / the serving frequency. After measurements are started
MOD 803 Cell for neighboring cells on a frequency, the UE reselects
EUTRA Selectio to a neighboring cell on the frequency only if the
NINTE n and RSRQ-based RX level of the serving cell is lower than
RNFRE Re- a specified threshold and that of the cell is higher than
Q selection the value specified by this parameter for a time-to-
trigger. For details, see 3GPP TS 36.331. This
LST parameter applies only to LTE FDD and LTE TDD.
EUTRA
NINTE GUI Value Range: 0~31
RNFRE Unit: dB
Q Actual Value Range: 0~31
Default Value: 0

UtranNF ThreshX ADD LBFD-0 Cell Meaning:


req LowQ UTRAN 0201803 Selectio Indicates the RSRQ-based minimum RX level
NFREQ / n and required for a neighboring cell on the frequency to
MOD TDLBF Reselect become a candidate for reselection if the RSRQ-based
UTRAN D-00201 ion / priority of the frequency is lower than that of the
NFREQ 803 Cell serving frequency.
Selectio
LST n and After measurements are started for neighboring cells
UTRAN Re- on the frequency, the UE reselects to a cell on the
NFREQ selection frequency only if the RSRQ-based RX level of the
serving cell is lower than a specified threshold and
that of the cell is higher than the value specified by
this parameter for a time-to-trigger. For details, see
3GPP TS 36.331. This parameter applies only to LTE
FDD and LTE TDD.
GUI Value Range: 0~31
Unit: dB
Actual Value Range: 0~31
Default Value: 0

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 119


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

UtranNF ThreshX ADD LBFD-0 Cell Meaning: Indicates the minimum RX level required
req Low UTRAN 0201803 Selectio for a neighboring cell on the UTRAN frequency to
NFREQ / n and become a candidate for reselection if the priority of
MOD TDLBF Reselect the frequency is lower than that of the serving
UTRAN D-00201 ion frequency. After measurements are started for
NFREQ 803 neighboring cells on the UTRAN frequency, the UE
reselects to a neighboring cell on the frequency only if
LST the RX level of the serving cell is lower than a
UTRAN specified threshold and that of the cell is higher than
NFREQ the value specified by this parameter for a time-to-
trigger. For details, see 3GPP TS 36.331. This
parameter applies only to LTE FDD and LTE TDD.
GUI Value Range: 0~31
Unit: 2dB
Actual Value Range: 0~62
Default Value: 6

GeranNf ThreshX ADD LBFD-0 Cell Meaning:


reqGrou Low GERAN 0201803 Selectio Indicates the minimum RX level required for a
p NFREQ / n and neighboring cell on the GERAN frequency to become
GROUP TDLBF Reselect a candidate for reselection if the priority of this target
MOD D-00201 ion frequency is lower than that of the serving frequency.
GERAN 803
NFREQ After measurements are started for neighboring cells
GROUP on the target frequency, the UE reselects a
neighboring cell on this frequency only when the RX
LST level of the serving cell is lower than a specified
GERAN threshold and that of the neighboring cell is higher
NFREQ than the value specified by this parameter for a time-
GROUP to-trigger. For details, see 3GPP TS 36.104. This
parameter applies only to LTE FDD and LTE TDD.
GUI Value Range: 0~31
Unit: 2dB
Actual Value Range: 0~62
Default Value: 7

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 120


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

Cdma20 Cdma20 ADD LBFD-0 Cell Meaning:


00Band 001Xrtt CDMA2 0201803 Selectio Indicates the RX signal level required for a cell on a
Class ThreshX 000BA / n and frequency in the lower-priority CDMA2000 1xRTT
Low NDCLA TDLBF Re- band class to become a candidate for cell reselection.
SS D-00201 selection
MOD 803 CS After measurements are started for cells on a
CDMA2 LOFD-0 Fallback frequency in the band class, a cell on the frequency
000BA 01035 / to can become a candidate for reselection only if the RX
NDCLA TDLOF CDMA2 signal level of the cell is better than the value
SS D-00103 000 specified by this parameter for a time-to-trigger. For
5 1xRTT details, see section 5.2.4.5 in 3GPP TS 36.304. This
LST parameter applies only to LTE FDD and LTE TDD.
CDMA2 LOFD-0 Enhance
000BA 01090 / d CS GUI Value Range: -63~0
NDCLA TDLOF Fallback Unit: 0.5dB
SS D-00109 to Actual Value Range: -31.5~0
0 CDMA2
000 Default Value: -34
1xRTT

Cdma20 Cdma20 ADD LBFD-0 Cell Meaning:


00Band 00Hrpd CDMA2 0201803 Selectio Indicates the RX signal level required for a cell on a
Class ThreshX 000BA / n and frequency in the lower-priority CDMA2000 HRPD
Low NDCLA TDLBF Re- band class to become a candidate for cell reselection.
SS D-00201 selection
MOD 803 PS Inter- After measurements are started for cells on a
CDMA2 LOFD-0 RAT frequency in the band class, a cell on the frequency
000BA 01021 / Mobility can become a candidate for reselection only if the RX
NDCLA TDLOF between signal level of the cell is lower than the value
SS D-00102 E- specified by this parameter for a time-to-trigger. For
1 UTRAN details, see section 5.2.4.5 in 3GPP TS 36.304. This
LST parameter applies only to LTE FDD and LTE TDD.
CDMA2 LOFD-0 and
000BA 01111 CDMA2 GUI Value Range: -63~0
NDCLA 000 Unit: 0.5dB
SS PS Actual Value Range: -31.5~0
Mobility
from E- Default Value: -26
UTRAN
to
CDMA2
000
HRPD
Based
on
Frequen
cy-
specific
Factors

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 121


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes ThrshSe MOD LBFD-0 Cell Meaning: Indicates the threshold used in the
el rvLow CELLR 0201803 Selectio evaluation of reselection to a cell on a lower priority
ESEL / n and E-UTRAN frequency or on an inter-RAT frequency.
LST TDLBF Re- Cell reselection to a cell on a lower priority E-
CELLR D-00201 selection UTRAN frequency or on an inter-RAT frequency is
ESEL 803 Broadca performed if no cell on the serving frequency or on a
LBFD-0 st of higher priority E-UTRAN frequency fulfills criteria 1
02009 / system for inter-frequency and inter-RAT reselections. For
TDLBF informat details, see 3GPP TS 36.304. This parameter applies
D-00200 ion only to LTE FDD and LTE TDD.
9 PS Inter- GUI Value Range: 0~31
LOFD-0 RAT Unit: 2dB
01021 / Mobility Actual Value Range: 0~62
TDLOF between
D-00102 E- Default Value: 7
1 UTRAN
LOFD-0 and
01111 CDMA2
000
PS
Mobility
from E-
UTRAN
to
CDMA2
000
HRPD
Based
on
Frequen
cy-
specific
Factors

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 122


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

EutranIn ThreshX ADD LBFD-0 Cell Meaning: Indicates the minimum RX level required
terNFre low EUTRA 0201803 Selectio for a neighboring cell on the frequency to become a
q NINTE / n and candidate for reselection if the priority of the
RNFRE TDLBF Reselect frequency is lower than that of the serving frequency.
Q D-00201 ion After measurements are started for neighboring cells
MOD 803 on the frequency, the UE reselects to a neighboring
EUTRA cell on the frequency only if the RX level of the
NINTE serving cell is lower than the ThrshServLow
RNFRE parameter value and that of the cell is higher than the
Q value specified by this parameter for a time-to-trigger.
For details, see 3GPP TS 36.331. This parameter
LST applies only to LTE FDD and LTE TDD.
EUTRA
NINTE GUI Value Range: 0~31
RNFRE Unit: 2dB
Q Actual Value Range: 0~62
Default Value: 11

CellRes SpeedD MOD LBFD-0 Cell Meaning: Indicates whether to set the parameters
el epResel CELLR 0201803 Selectio related to rate-dependent cell reselection. This
CfgInd ESEL / n and parameter applies only to LTE FDD and LTE TDD.
LST TDLBF Re- GUI Value Range: NOT_CFG(Not configure),
CELLR D-00201 selection CFG(Configure)
ESEL 803 Broadca Unit: None
LBFD-0 st of
02009 / system Actual Value Range: NOT_CFG, CFG
TDLBF informat Default Value: NOT_CFG(Not configure)
D-00200 ion
9

CellRes SpeedSt MOD LBFD-0 Cell Meaning: Indicates whether to set the scaling
el ateSfCfg CELLR 0201803 Selectio parameters for rate-dependent cell reselection within
Ind ESEL / n and E-UTRAN. This parameter applies only to LTE FDD
LST TDLBF Re- and LTE TDD.
CELLR D-00201 selection GUI Value Range: NOT_CFG(Not configure),
ESEL 803 Broadca CFG(Configure)
LBFD-0 st of Unit: None
02009 / system
TDLBF informat Actual Value Range: NOT_CFG, CFG
D-00200 ion Default Value: CFG(Configure)
9

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 123


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

EutranIn SpeedD ADD LBFD-0 Cell Meaning:


terNFre ependSP EUTRA 0201803 Selectio Indicates whether to set the speed-dependent scaling
q CfgInd NINTE / n and parameters related to cell reselection.
RNFRE TDLBF Re-
Q D-00201 selection If this parameter is set to NOT_CFG, speed-dependent
MOD 803 cell reselections are not supported by default. This
EUTRA parameter applies only to LTE FDD and LTE TDD.
NINTE GUI Value Range: NOT_CFG(Not configure),
RNFRE CFG(Configure)
Q Unit: None
LST Actual Value Range: NOT_CFG, CFG
EUTRA
NINTE Default Value: NOT_CFG(Not configure)
RNFRE
Q

CellRes SpeedSt ADD LBFD-0 Cell Meaning: Indicates whether to set the speed-
elUtran ateSfCfg CELLR 0201803 Selectio dependent scaling parameters related to cell
Ind ESELU / n and reselection to UTRAN. This parameter applies only to
TRAN TDLBF Re- LTE FDD and LTE TDD.
MOD D-00201 selection GUI Value Range: NOT_CFG(Not configure),
CELLR 803 Broadca CFG(Configure)
ESELU LBFD-0 st of Unit: None
TRAN 02009 / system
TDLBF informat Actual Value Range: NOT_CFG, CFG
LST
CELLR D-00200 ion Default Value: NOT_CFG(Not configure)
ESELU 9
TRAN

CellRes SpeedSt ADD LBFD-0 Cell Meaning: Indicates whether to set the speed-
elGeran ateSfCfg CELLR 0201803 Selectio dependent scaling parameters related to cell
Ind ESELG / n and reselection to GERAN. This parameter applies only to
ERAN TDLBF Re- LTE FDD and LTE TDD.
MOD D-00201 selection GUI Value Range: NOT_CFG(Not configure),
CELLR 803 Broadca CFG(Configure)
ESELG LBFD-0 st of Unit: None
ERAN 02009 / system
TDLBF informat Actual Value Range: NOT_CFG, CFG
LST
CELLR D-00200 ion Default Value: NOT_CFG(Not configure)
ESELG 9
ERAN

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 124


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes SpeedSt ADD LBFD-0 Cell Meaning: Indicates whether to set the speed-
elCdma ateSfCfg CELLR 0201803 Selectio dependent scaling parameters related to cell
2000 Ind ESELC / n and reselection to CDMA2000 HRPD. For details, see
DMA20 TDLBF Re- 3GPP TS 36.331. This parameter applies only to LTE
00 D-00201 selection FDD and LTE TDD.
MOD 803 PS Inter- GUI Value Range: NOT_CFG(Not configure),
CELLR LOFD-0 RAT CFG(Configure)
ESELC 01021 / Mobility Unit: None
DMA20 TDLOF between
00 D-00102 E- Actual Value Range: NOT_CFG, CFG

LST 1 UTRAN Default Value: NOT_CFG(Not configure)


CELLR LBFD-0 and
ESELC 02009 / CDMA2
DMA20 TDLBF 000
00 D-00200 Broadca
9 st of
system
informat
ion

CellRes Cdma1 ADD LBFD-0 Cell Meaning: Indicates whether speed-dependent scaling
elCdma XrttSpee CELLR 0201803 Selectio parameters need to be set for cell reselection to
2000 dStateCf ESELC / n and CDMA2000 1xRTT. This parameter applies only to
gInd DMA20 TDLBF Re- LTE FDD and LTE TDD.
00 D-00201 selection GUI Value Range: NOT_CFG(Not configure),
MOD 803 CS CFG(Configure)
CELLR LOFD-0 Fallback Unit: None
ESELC 01035 / to
DMA20 TDLOF CDMA2 Actual Value Range: NOT_CFG, CFG
00 D-00103 000 Default Value: NOT_CFG(Not configure)
LST 5 1xRTT
CELLR LBFD-0 Broadca
ESELC 02009 / st of
DMA20 TDLBF system
00 D-00200 informat
9 ion
TDLOF Enhance
D-00109 d CS
0/ Fallback
LOFD-0 to
01090 CDMA2
000
1xRTT

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 125


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes NCellCh MOD LBFD-0 Cell Meaning: Indicates the threshold of the number of cell
el angeMe CELLR 0201803 Selectio reselections, which is used for a UE to enter the
dium ESEL / n and medium mobility state. This parameter is one of the
LST TDLBF Re- key parameters in determining the mobility state of
CELLR D-00201 selection the UE. During the UE mobility evaluation, if the
ESEL 803 Broadca number of cell reselections is greater than this
LBFD-0 st of parameter value and is less than or equal to the
02009 / system NCellChangeHigh parameter value, the UE enters the
TDLBF informat medium mobility state. This parameter applies only to
D-00200 ion LTE FDD and LTE TDD.
9 GUI Value Range: 1~16
Unit: None
Actual Value Range: 1~16
Default Value: 4

CellRes NCellCh MOD LBFD-0 Cell Meaning: Indicates the threshold of the number of cell
el angeHig CELLR 0201803 Selectio reselections, which is used for a UE to enter the high
h ESEL / n and mobility state. This parameter is one of the key
LST TDLBF Re- parameters in determining the mobility state of the
CELLR D-00201 selection UE. During the UE mobility evaluation, if the number
ESEL 803 Broadca of cell reselections is greater than this parameter
LBFD-0 st of value, the UE enters the high mobility state. This
02009 / system parameter applies only to LTE FDD and LTE TDD.
TDLBF informat GUI Value Range: 1~16
D-00200 ion Unit: None
9
Actual Value Range: 1~16
Default Value: 8

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 126


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes TEvalua MOD LBFD-0 Broadca Meaning: Indicates the duration in which the mobility
el tion CELLR 02009 / st of status of the UE is evaluated. This parameter is one of
ESEL TDLBF system the key parameters in deciding on the UE mobility
LST D-00200 informat state. A smaller value of this parameter may lead to
CELLR 9 ion more frequent state transitions and lower decision
ESEL LBFD-0 Cell accuracy. A larger value of this parameter leads to the
0201803 Selectio opposite effect. This parameter applies only to LTE
/ n and FDD and LTE TDD.
TDLBF Re- GUI Value Range: S30_T_EVALULATION(30s),
D-00201 selection S60_T_EVALULATION(60s),
803 S120_T_EVALULATION(120s),
S180_T_EVALULATION(180s),
S240_T_EVALULATION(240s)
Unit: s
Actual Value Range: S30_T_EVALULATION,
S60_T_EVALULATION, S120_T_EVALULATION,
S180_T_EVALULATION, S240_T_EVALULATION
Default Value: S60_T_EVALULATION(60s)

CellRes THystN MOD LBFD-0 Broadca Meaning: Indicates the extra duration required in the
el ormal CELLR 02009 / st of evaluation before the UE can enter the normal-
ESEL TDLBF system mobility state. This parameter can prevent UEs from
LST D-00200 informat frequently switching from the high- or medium-
CELLR 9 ion mobility state to the normal-mobility state, and is one
ESEL LBFD-0 Cell of the key parameters in deciding on the UE mobility.
0201803 Selectio A larger value of this parameter leads to a lower
/ n and probability of transition from the high- or medium-
TDLBF Re- mobility state to the normal-mobility state but higher
D-00201 selection decision accuracy. A smaller value of this parameter
803 leads to the opposite effect. This parameter applies
only to LTE FDD and LTE TDD.
GUI Value Range: S30_T_HYST_NORMAL(30s),
S60_T_HYST_NORMAL(60s),
S120_T_HYST_NORMAL(120s),
S180_T_HYST_NORMAL(180s),
S240_T_HYST_NORMAL(240s)
Unit: s
Actual Value Range: S30_T_HYST_NORMAL,
S60_T_HYST_NORMAL,
S120_T_HYST_NORMAL,
S180_T_HYST_NORMAL,
S240_T_HYST_NORMAL
Default Value: S30_T_HYST_NORMAL(30s)

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 127


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes TReselE MOD LBFD-0 Cell Meaning: Indicates the scaling factor applied to
el utranSf CELLR 0201803 Selectio TReselEutran for medium-mobility UEs. The actual
Medium ESEL / n and duration of cell reselection for medium-mobility UEs
LST TDLBF Re- to E-UTRAN is equal to the product of TReselEutran
CELLR D-00201 selection and TReselEutranSfMedium. This parameter applies
ESEL 803 Broadca only to LTE FDD and LTE TDD.
LBFD-0 st of GUI Value Range: T_RESEL_SF_0DOT25(0.25),
02009 / system T_RESEL_SF_0DOT5(0.5),
TDLBF informat T_RESEL_SF_0DOT75(0.75),
D-00200 ion T_RESEL_SF_1DOT0(1.0)
9 Unit: None
Actual Value Range: T_RESEL_SF_0DOT25,
T_RESEL_SF_0DOT5, T_RESEL_SF_0DOT75,
T_RESEL_SF_1DOT0
Default Value: T_RESEL_SF_1DOT0(1.0)

EutranIn TReselE ADD LBFD-0 Cell Meaning: Indicates the scaling factor applied to the
terNFre utranSf EUTRA 0201803 Selectio cell reselection duration for medium-mobility UEs.
q Medium NINTE / n and This parameter is delivered in SIB5. For details, see
RNFRE TDLBF Re- 3GPP TS 36.331. This parameter applies only to LTE
Q D-00201 selection FDD and LTE TDD.
MOD 803 GUI Value Range: 0DOT25_ENUM(0.25),
EUTRA 0DOT5_ENUM(0.5), 0DOT75_ENUM(0.75),
NINTE 1DOT0_ENUM(1.0)
RNFRE Unit: None
Q
Actual Value Range: 0DOT25_ENUM,
LST 0DOT5_ENUM, 0DOT75_ENUM, 1DOT0_ENUM
EUTRA
NINTE Default Value: 1DOT0_ENUM(1.0)
RNFRE
Q

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 128


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes TReselU ADD LBFD-0 Cell Meaning:


elUtran tranSfM CELLR 0201803 Selectio Indicates the scaling factor applied to TReselUtran for
edium ESELU / n and medium-mobility UEs. The actual duration of cell
TRAN TDLBF Re- reselection of medium-mobility UEs to UTRAN is
MOD D-00201 selection equal to TReselUtran multiplied by
CELLR 803 Broadca TReselUtranSfMedium.
ESELU LBFD-0 st of
TRAN 02009 / system The value T_RESEL_SF_0DOT25 means a scaling
TDLBF informat factor of 0.25, T_RESEL_SF_0DOT5 means 0.5, and
LST so on. This parameter applies only to LTE FDD and
CELLR D-00200 ion
9 LTE TDD.
ESELU
TRAN GUI Value Range: T_RESEL_SF_0DOT25(0.25),
T_RESEL_SF_0DOT5(0.5),
T_RESEL_SF_0DOT75(0.75),
T_RESEL_SF_1DOT0(1.0)
Unit: None
Actual Value Range: T_RESEL_SF_0DOT25,
T_RESEL_SF_0DOT5, T_RESEL_SF_0DOT75,
T_RESEL_SF_1DOT0
Default Value: T_RESEL_SF_1DOT0(1.0)

CellRes TReselG ADD LBFD-0 Cell Meaning: Indicates the scaling factor applied to
elGeran eranSfM CELLR 0201803 Selectio TReselGeran for medium-mobility UEs. The actual
edium ESELG / n and duration of cell reselection of medium-mobility UEs
ERAN TDLBF Re- to GERAN is equal to TReselGeran multiplied by
MOD D-00201 selection TReselGeranSfMedium. This parameter applies only
CELLR 803 Broadca to LTE FDD and LTE TDD.
ESELG LBFD-0 st of GUI Value Range: T_RESEL_SF_0DOT25(0.25),
ERAN 02009 / system T_RESEL_SF_0DOT5(0.5),
LST TDLBF informat T_RESEL_SF_0DOT75(0.75),
CELLR D-00200 ion T_RESEL_SF_1DOT0(1.0)
ESELG 9 Unit: None
ERAN Actual Value Range: T_RESEL_SF_0DOT25,
T_RESEL_SF_0DOT5, T_RESEL_SF_0DOT75,
T_RESEL_SF_1DOT0
Default Value: T_RESEL_SF_1DOT0(1.0)

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 129


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes TReselC ADD LBFD-0 Cell Meaning: Indicates the scaling factor applied to
elCdma dmaHrp CELLR 0201803 Selectio TReselCdmaHrpd for medium-mobility UEs. The
2000 dSfMedi ESELC / n and actual duration of cell reselection of medium-mobility
um DMA20 TDLBF Re- UEs to CDMA2000 HRPD is equal to
00 D-00201 selection TReselCdmaHrpd multiplied by TReselCdmaHrpdSf-
MOD 803 PS Inter- Medium. For details, see 3GPP TS 36.331. This
CELLR LOFD-0 RAT parameter applies only to LTE FDD and LTE TDD.
ESELC 01021 / Mobility GUI Value Range: T_RESEL_SF_0DOT25(0.25),
DMA20 TDLOF between T_RESEL_SF_0DOT5(0.5),
00 D-00102 E- T_RESEL_SF_0DOT75(0.75),
LST 1 UTRAN T_RESEL_SF_1DOT0(1.0)
CELLR LBFD-0 and Unit: None
ESELC 02009 / CDMA2
000 Actual Value Range: T_RESEL_SF_0DOT25,
DMA20 TDLBF T_RESEL_SF_0DOT5, T_RESEL_SF_0DOT75,
00 D-00200 Broadca T_RESEL_SF_1DOT0
9 st of
system Default Value: T_RESEL_SF_1DOT0(1.0)
informat
ion

CellRes Cdma1 ADD LBFD-0 Cell Meaning: Indicates the scaling factor applicable to cell
elCdma XrttSfM CELLR 0201803 Selectio reselection of medium-mobility UEs to CDMA2000
2000 edium ESELC / n and 1xRTT. For details, see 3GPP TS 36.331. This
DMA20 TDLBF Re- parameter applies only to LTE FDD and LTE TDD.
00 D-00201 selection GUI Value Range: T_RESEL_SF_0DOT25(0.25),
MOD 803 CS T_RESEL_SF_0DOT5(0.5),
CELLR LOFD-0 Fallback T_RESEL_SF_0DOT75(0.75),
ESELC 01035 / to T_RESEL_SF_1DOT0(1.0)
DMA20 TDLOF CDMA2 Unit: None
00 D-00103 000
5 1xRTT Actual Value Range: T_RESEL_SF_0DOT25,
LST T_RESEL_SF_0DOT5, T_RESEL_SF_0DOT75,
CELLR LBFD-0 Broadca T_RESEL_SF_1DOT0
ESELC 02009 / st of
DMA20 TDLBF system Default Value: T_RESEL_SF_1DOT0(1.0)
00 D-00200 informat
9 ion
TDLOF Enhance
D-00109 d CS
0/ Fallback
LOFD-0 to
01090 CDMA2
000
1xRTT

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 130


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes TReselE MOD LBFD-0 Cell Meaning: Indicates the scaling factor applied to
el utranSf CELLR 0201803 Selectio TReselEutran for high-mobility UEs. The actual
High ESEL / n and duration of cell reselection of high-mobility UEs to E-
LST TDLBF Re- UTRAN is equal to TReselEutran multiplied by
CELLR D-00201 selection TReselEutranSfHigh. This parameter applies only to
ESEL 803 Broadca LTE FDD and LTE TDD.
LBFD-0 st of GUI Value Range: T_RESEL_SF_0DOT25(0.25),
02009 / system T_RESEL_SF_0DOT5(0.5),
TDLBF informat T_RESEL_SF_0DOT75(0.75),
D-00200 ion T_RESEL_SF_1DOT0(1.0)
9 Unit: None
Actual Value Range: T_RESEL_SF_0DOT25,
T_RESEL_SF_0DOT5, T_RESEL_SF_0DOT75,
T_RESEL_SF_1DOT0
Default Value: T_RESEL_SF_0DOT75(0.75)

EutranIn TReselE ADD LBFD-0 Cell Meaning: Indicates the scaling factor applied to the
terNFre utranSf EUTRA 0201803 Selectio cell reselection duration for high-mobility UEs. This
q High NINTE / n and parameter is delivered in SIB5. For details, see 3GPP
RNFRE TDLBF Re- TS 36.331. This parameter applies only to LTE FDD
Q D-00201 selection and LTE TDD.
MOD 803 GUI Value Range: 0DOT25_ENUM(0.25),
EUTRA 0DOT5_ENUM(0.5), 0DOT75_ENUM(0.75),
NINTE 1DOT0_ENUM(1.0)
RNFRE Unit: None
Q
Actual Value Range: 0DOT25_ENUM,
LST 0DOT5_ENUM, 0DOT75_ENUM, 1DOT0_ENUM
EUTRA
NINTE Default Value: 0DOT75_ENUM(0.75)
RNFRE
Q

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 131


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes TReselU ADD LBFD-0 Cell Meaning:


elUtran tranSfHi CELLR 0201803 Selectio Indicates the scaling factor applied to TReselUtran for
gh ESELU / n and high-mobility UEs. The actual duration of cell
TRAN TDLBF Re- reselection of high-mobility UEs to UTRAN is equal
MOD D-00201 selection to TReselUtran multiplied by TReselUtranSfHigh.
CELLR 803 Broadca
ESELU LBFD-0 st of The value T_RESEL_SF_0DOT25 means a scaling
TRAN 02009 / system factor of 0.25, T_RESEL_SF_0DOT5 means 0.5, and
TDLBF informat so on. This parameter applies only to LTE FDD and
LST LTE TDD.
CELLR D-00200 ion
ESELU 9 GUI Value Range: T_RESEL_SF_0DOT25(0.25),
TRAN T_RESEL_SF_0DOT5(0.5),
T_RESEL_SF_0DOT75(0.75),
T_RESEL_SF_1DOT0(1.0)
Unit: None
Actual Value Range: T_RESEL_SF_0DOT25,
T_RESEL_SF_0DOT5, T_RESEL_SF_0DOT75,
T_RESEL_SF_1DOT0
Default Value: T_RESEL_SF_0DOT75(0.75)

CellRes TReselG ADD LBFD-0 Cell Meaning: Indicates the scaling factor applied to
elGeran eranSfH CELLR 0201803 Selectio TReselGeran for high-mobility UEs. The actual
igh ESELG / n and duration of cell reselection of high-mobility UEs to
ERAN TDLBF Re- GERAN is equal to TReselGeran multiplied by
MOD D-00201 selection TReselGeranSfHigh. This parameter applies only to
CELLR 803 Broadca LTE FDD and LTE TDD.
ESELG LBFD-0 st of GUI Value Range: T_RESEL_SF_0DOT25(0.25),
ERAN 02009 / system T_RESEL_SF_0DOT5(0.5),
LST TDLBF informat T_RESEL_SF_0DOT75(0.75),
CELLR D-00200 ion T_RESEL_SF_1DOT0(1.0)
ESELG 9 Unit: None
ERAN Actual Value Range: T_RESEL_SF_0DOT25,
T_RESEL_SF_0DOT5, T_RESEL_SF_0DOT75,
T_RESEL_SF_1DOT0
Default Value: T_RESEL_SF_0DOT75(0.75)

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 132


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes TReselC ADD LBFD-0 Cell Meaning: Indicates the scaling factor applied to
elCdma dmaHrp CELLR 0201803 Selectio TReselCdmaHrpd for high-mobility UEs. The actual
2000 dSfHigh ESELC / n and duration of cell reselection of high-mobility UEs to
DMA20 TDLBF Re- CDMA2000 HRPD is equal to TReselCdmaHrpd
00 D-00201 selection multiplied by TReselCdmaHrpdSfHigh. For details,
MOD 803 PS Inter- see 3GPP TS 36.331. This parameter applies only to
CELLR LOFD-0 RAT LTE FDD and LTE TDD.
ESELC 01021 / Mobility GUI Value Range: T_RESEL_SF_0DOT25(0.25),
DMA20 TDLOF between T_RESEL_SF_0DOT5(0.5),
00 D-00102 E- T_RESEL_SF_0DOT75(0.75),
LST 1 UTRAN T_RESEL_SF_1DOT0(1.0)
CELLR LBFD-0 and Unit: None
ESELC 02009 / CDMA2
000 Actual Value Range: T_RESEL_SF_0DOT25,
DMA20 TDLBF T_RESEL_SF_0DOT5, T_RESEL_SF_0DOT75,
00 D-00200 Broadca T_RESEL_SF_1DOT0
9 st of
system Default Value: T_RESEL_SF_0DOT75(0.75)
informat
ion

CellRes Cdma1 ADD LBFD-0 Cell Meaning: Indicates the scaling factor applicable to cell
elCdma XrttSfHi CELLR 0201803 Selectio reselection of high-mobility UEs to CDMA2000
2000 gh ESELC / n and 1xRTT. For details, see 3GPP TS 36.331. This
DMA20 TDLBF Re- parameter applies only to LTE FDD and LTE TDD.
00 D-00201 selection GUI Value Range: T_RESEL_SF_0DOT25(0.25),
MOD 803 CS T_RESEL_SF_0DOT5(0.5),
CELLR LOFD-0 Fallback T_RESEL_SF_0DOT75(0.75),
ESELC 01035 / to T_RESEL_SF_1DOT0(1.0)
DMA20 TDLOF CDMA2 Unit: None
00 D-00103 000
5 1xRTT Actual Value Range: T_RESEL_SF_0DOT25,
LST T_RESEL_SF_0DOT5, T_RESEL_SF_0DOT75,
CELLR LBFD-0 Broadca T_RESEL_SF_1DOT0
ESELC 02009 / st of
DMA20 TDLBF system Default Value: T_RESEL_SF_0DOT75(0.75)
00 D-00200 informat
9 ion
TDLOF Enhance
D-00109 d CS
0/ Fallback
LOFD-0 to
01090 CDMA2
000
1xRTT

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 133


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes QHystSf MOD LBFD-0 Broadca Meaning: Indicates the scaling factor (or known as
el Medium CELLR 02009 / st of additional hysteresis) applied to Qhyst for medium-
ESEL TDLBF system mobility UEs. For details, see 3GPP TS 36.304 and
LST D-00200 informat 3GPP TS 36.331. This parameter applies only to LTE
CELLR 9 ion FDD and LTE TDD.
ESEL LBFD-0 Cell GUI Value Range:
0201803 Selectio DB_6_Q_HYST_SF_MEDIUM(-6dB),
/ n and DB_4_Q_HYST_SF_MEDIUM(-4dB),
TDLBF Re- DB_2_Q_HYST_SF_MEDIUM(-2dB),
D-00201 selection DB0_Q_HYST_SF_MEDIUM(0dB)
803 Unit: dB
Actual Value Range: DB_6_Q_HYST_SF_MEDIUM,
DB_4_Q_HYST_SF_MEDIUM,
DB_2_Q_HYST_SF_MEDIUM,
DB0_Q_HYST_SF_MEDIUM
Default Value: DB0_Q_HYST_SF_MEDIUM(0dB)

CellRes QHystSf MOD LBFD-0 Broadca Meaning: Indicates the scaling factor (or known as
el High CELLR 02009 / st of additional hysteresis) applied to Qhyst for high-
ESEL TDLBF system mobility UEs. For details, see 3GPP TS 36.304 and
LST D-00200 informat 3GPP TS 36.331. This parameter applies only to LTE
CELLR 9 ion FDD and LTE TDD.
ESEL LBFD-0 Cell GUI Value Range: DB_6_Q_HYST_SF_HIGH(-6dB),
0201803 Selectio DB_4_Q_HYST_SF_HIGH(-4dB),
/ n and DB_2_Q_HYST_SF_HIGH(-2dB),
TDLBF Re- DB0_Q_HYST_SF_HIGH(0dB)
D-00201 selection Unit: dB
803
Actual Value Range: DB_6_Q_HYST_SF_HIGH,
DB_4_Q_HYST_SF_HIGH,
DB_2_Q_HYST_SF_HIGH,
DB0_Q_HYST_SF_HIGH
Default Value: DB0_Q_HYST_SF_HIGH(0dB)

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 134


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellAcc IntraFre MOD LBFD-0 Broadca Meaning:


ess qResel CELLA 02009 / st of Indicates whether the cell can initiate the intra-
CCESS TDLBF system frequency cell reselection when the cell is barred.
LST D-00200 informat
CELLA 9/ ion NOT_ALLOWED means that the UE cannot initiate
CCESS MLBFD Cell the intra-frequency cell reselection, and ALLOWED
-120002 Selectio means that the UE can initiate the intra-frequency cell
29 n and reselection.
LBFD-0 Re- GUI Value Range: ALLOWED, NOT_ALLOWED
0201803 selection Unit: None
/
TDLBF Actual Value Range: ALLOWED, NOT_ALLOWED
D-00201 Default Value: ALLOWED
803 /
MLBFD
-120002
37

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 135


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellSiM SiSwitc MOD LBFD-0 Broadca Meaning:


ap h CELLSI 02009 / st of Indicates the system information broadcast policy for
MAP TDLBF system the cell.
LST D-00200 informat
CELLSI 9 ion OnlyCellSiSwitch(DlOnlyCellSiSwitch): Indicates
MAP LOFD-0 eMBMS whether to broadcast system information in the cell,
70220 / Phase 1 whose Cell.WorkMode is set to DL_ONLY. System
TDLOF based on information is broadcast in the cell only if this option
D-07022 Centrali is selected. This option applies only to LTE FDD cells
0 zed whose Cell.WorkMode is set to DL_ONLY.
MCE Sib6Switch(Sib6Switch): Indicates whether to
Architec broadcast SIB6. If this option is deselected, SIB6 is
ture not broadcast. If this option is selected and the
CELLRESELUTRAN MO is created, SIB6 is
broadcast. For details about the contents of SIB6, see
3GPP TS 36.331. This option applies only to LTE
FDD and LTE TDD.
Sib7Switch(Sib7Switch): Indicates whether to
broadcast SIB7. If this option is deselected, SIB7 is
not broadcast. If this option is selected and the
CELLRESELGERAN MO is created, SIB7 is
broadcast. For details about the contents of SIB7, see
3GPP TS 36.331. This option applies only to LTE
FDD and LTE TDD.
GUI Value Range:
DlOnlyCellSiSwitch(DlOnlyCellSiSwitch),
Sib6Switch(Sib6Switch), Sib7Switch(Sib7Switch)
Unit: None
Actual Value Range: DlOnlyCellSiSwitch,
Sib6Switch, Sib7Switch
Default Value: DlOnlyCellSiSwitch:Off,
Sib6Switch:On, Sib7Switch:On

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 136


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

BcchCfg ModifyP MOD LBFD-0 Broadca Meaning: Indicates the modification period coefficient
eriodCo BCCHC 02009 / st of for the BCCH. BCCH modification period is equal to
eff FG TDLBF system Modification period coefficient multiplies Default
LST D-00200 informat paging cycle, where the BCCH modification period
BCCHC 9 ion and default paging cycle are measured in unit of radio
FG frames, and the modification period coefficient is
specified by this parameter. This parameter applies
only to LTE FDD and LTE TDD.
GUI Value Range: MOD_PERIOD_COEFF_N2(2),
MOD_PERIOD_COEFF_N4(4),
MOD_PERIOD_COEFF_N8(8),
MOD_PERIOD_COEFF_N16(16)
Unit: None
Actual Value Range: MOD_PERIOD_COEFF_N2,
MOD_PERIOD_COEFF_N4,
MOD_PERIOD_COEFF_N8,
MOD_PERIOD_COEFF_N16
Default Value: MOD_PERIOD_COEFF_N2(2)

PCCHC DefaultP MOD LBFD-0 Broadca Meaning: Indicates the default paging period for the
fg agingCy PCCHC 02009 / st of cell. It is also called the default discontinuous
cle FG TDLBF system reception (DRX) period. If the EPC specifies a DRX
LST D-00200 informat period for a UE, the UE compares this period with the
PCCHC 9 ion value of this parameter and uses the smaller one as its
FG LBFD-0 Paging DRX period. If the EPC does not specify a DRX
02011 / period, the UE uses the value of this parameter, which
TDLBF is delivered in the system information, as its DRX
D-00201 period. For details, see 3GPP TS 36.304. This
1 parameter applies only to LTE FDD and LTE TDD.
GUI Value Range: rf32(32 radio frames), rf64(64
radio frames), rf128(128 radio frames), rf256(256
radio frames)
Unit: None
Actual Value Range: rf32, rf64, rf128, rf256
Default Value: rf128(128 radio frames)

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 137


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellSiM SibUpd MOD LBFD-0 Broadca Meaning:


ap OptSwit CELLSI 02009/ st of Indicates whether to enable the optimization scheme
ch MAP TDLBF system switch that controls SIB message update.
LST D-00200 informat
CELLSI 9 ion SibPagingOptCtrlSwitch: Indicates whether to enable
MAP the optimization of paging triggered by system
information update. If this option is selected, the
optimization scheme takes effect, and the paging cycle
is the same as the BCCH modification period. If this
option is deselected, the optimization scheme does not
take effect, and the paging cycle is occasionally less
than the BCCH modification period. This option
applies only to LTE FDD and LTE TDD.
GUI Value Range: SibPagingOptCtrlS-
witch(SibPagingOptCtrlSwitch)
Unit: None
Actual Value Range: SibPagingOptCtrlSwitch
Default Value: SibPagingOptCtrlSwitch:Off

PCCHC PagingS MOD LBFD-0 Paging Meaning: Indicates the number of paging messages
fg entNum PCCHC 02011 / transmitted to UEs over the air interface. This
FG TDLBF parameter applies only to LTE FDD and LTE TDD.
LST D-00201 GUI Value Range: 1~3
PCCHC 1
Unit: None
FG
Actual Value Range: 1~3
Default Value: 1

GlobalP S1Defau MOD LBFD-0 Paging Meaning: Indicates the value of the IE Default paging
rocSwitc ltPaging GLOBA 02011 / DRX contained in the S1 SETUP REQUEST and
h DrxSele LPROC TDLBF ENB CONFIGURATION UPDATE messages that the
ct SWITC D-00201 eNodeB sends over the S1 interface. For details, see
H 1 3GPP TS 36.413.
LST GUI Value Range: v32(v32), v64(v64), v128(v128),
GLOBA v256(v256)
LPROC Unit: None
SWITC
H Actual Value Range: v32, v64, v128, v256
Default Value: v128(v128)

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 138


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

PCCHC Nb MOD LBFD-0 Broadca Meaning: Indicates the number of paging occasions (a
fg PCCHC 02009 / st of type of subframe) within a paging period. This
FG TDLBF system parameter value also indicates the number of paging
LST D-00200 informat groups within a paging period. For details, see 3GPP
PCCHC 9 ion TS 36.304.
FG LBFD-0 Paging GUI Value Range: FOURT, TWOT, ONET, HALFT,
02011 / Breathin QUARTERT, ONE_EIGHTT, ONE_SIXTEENTHT,
TDLBF g Pilot ONE_THIRTY_SECONDT
D-00201 Unit: None
1
Actual Value Range: FOURT, TWOT, ONET,
LEOFD- HALFT, QUARTERT, ONE_EIGHTT,
111306 / ONE_SIXTEENTHT, ONE_THIRTY_SECONDT
TDLOF
D-12020 Default Value: ONET
5

CellDlsc RarAnd MOD LBFD-0 Paging Meaning: Indicates the code rate for Random Access
hAlgo PagingC CELLD 02011/ Random Response messages and paging messages. This
R LSCHA TDLBF Access parameter applies only to LTE FDD and LTE TDD.
LGO D-00201 Procedu GUI Value Range: 10~930
LST 1 re Unit: None
CELLD LBFD-0
LSCHA 02010/ Actual Value Range: 0.010~0.930, step:0.001
LGO TDLBF Default Value: 117
D-00201
0

PCCHC MaxPag MOD LBFD-0 Paging Meaning: Indicates the maximum number of UEs that
fg ingReco PCCHC 02011 / can be included in a paging message on each paging
rdsNum FG TDLBF occasion. This parameter applies only to LTE FDD
LST D-00201 and LTE TDD.
PCCHC 1 GUI Value Range: 1~16
FG Unit: None
Actual Value Range: 1~16
Default Value: 16

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 139


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

PCCHC PagingS MOD TDLBF Paging Meaning: Indicates a paging message sending policy.
fg trategy PCCHC D-00201 There are two policies: first in first out (FIFO) and
FG 1/ priority differentiation. FIFO means that paging
LST LBFD-0 messages that arrive earlier are preferentially sent in a
PCCHC 02011 / paging occasion. Priority differentiation means higher-
FG MLBFD priority paging messages are preferentially sent in a
-120002 paging occasion.
31 GUI Value Range:
PAGING_STRATEGY_FIFO(First-in First-out
Strategy), PAGING_STRATEGY_DIFFPRI(Priority
Differentiation Strategy)
Unit: None
Actual Value Range: PAGING_STRATEGY_FIFO,
PAGING_STRATEGY_DIFFPRI
Default Value: PAGING_STRATEGY_FIFO(First-in
First-out Strategy)

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 140


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellAlg DlSchS MOD LOFD-1 Traffic Meaning:


oSwitch witch CELLA 10205 / Model Indicates whether to enable downlink scheduling
LGOSW TDLOF Based algorithms in a cell. This parameter includes the
ITCH D-11022 Perform following options:
LST 7 ance
CELLA LOFD-0 Optimiz FreqSelSwitch: Indicates whether to enable
LGOSW 01016 / ation frequency-selective scheduling. If this option is
ITCH TDLOF VoIP selected, data is transmitted on the frequency band of
D-00101 Semi- high channel quality. This option applies only to LTE
6 persisten FDD and LTE TDD.
LBFD-0 t
SpsSchSwitch: Indicates whether to enable semi-
0101502 Scheduli
persistent scheduling during talk spurts of VoLTE
/ ng
services. If this option is selected, semi-persistent
TDLBF Dynami scheduling is applied during talk spurts of VoLTE
D-00101 c services. If this option is deselected, dynamic
502 Scheduli scheduling is applied during talk spurts of VoLTE
LOFD-0 ng services. This option applies only to LTE FDD and
01109 / DL LTE TDD.
TDLOF Non-
MBSFNShutDownSwitch: Indicates whether to
D-00110 GBR
enable Multimedia Broadcast multicast service Single
9 Packet
Frequency Network (MBSFN) subframe shutdown. If
LOFD-0 Bundlin
this option is selected, MBSFN subframe shutdown is
01070 / g
applied. If this option is deselected, MBSFN subframe
TDLOF Symbol shutdown is not applied. This option takes effect only
D-00107 Power if the SymbolShutdownSwitch option of the
0 Saving PowerSaveSwitch parameter is selected. If the
TDLOF Scheduli MBSFNShutDownSwitch option is selected, the
D-07022 ng setting of the switch for mapping SIBs to SI messages
4/ Based becomes invalid. If the MBSFNShutDownSwitch
TDLOF on Max option is deselected, the setting of the switch for
D-07022 Bit Rate mapping SIBs to SI messages becomes valid. The
2 MBSFNShutDownSwitch option applies only to LTE-
Basic
LBFD-0 only base stations. This option applies only to LTE
Scheduli
02025 / FDD and LTE TDD.
ng
TDLBF Support NonGbrBundlingSwitch: Indicates whether to enable
D-00202 of downlink non-GBR packet bundling. If this option is
5 aperiodi selected, delay of non-GBR services can be controlled
LBFD-0 c CQI in non-congestion scenarios. If this option is
02031 / reports deselected, delay of non-GBR services cannot be
TDLBF MBR>G controlled. This option applies only to LTE FDD and
D-00203 BR LTE TDD.
1 Configu EnAperiodicCqiRptSwitch: Indicates whether to
LBFD-0 ration enable enhanced aperiodic channel quality indicator
70102 / Enhance (CQI) reporting. If this option is selected, the eNodeB
TDLBF d DL triggers aperiodic CQI reporting for a UE based on
Frequen downlink services of the UE and the interval at which

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 141


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

D-07010 cy the UE sends periodic CQI reports. If this option is


2 Selectiv deselected, UEs under non-frequency-selective
LBFD-0 e scheduling do not trigger aperiodic CQI reporting
60202 Enhance based on downlink services and trigger an aperiodic
d CQI reporting if no valid periodic CQI reports are sent
LOFD-0 in eight consecutive periodic CQI reporting periods.
81218 extende
d QCI This option applies only to LTE FDD and LTE TDD.
LTROF
D-11120 MCPTT DlMbrCtrlSwitch: Indicates whether to enable
4/ Voice downlink scheduling based on the maximum bit rate
TDLOF Manage (MBR) and guaranteed bit rate (GBR) on GBR
D-12110 ment bearers. If this option is selected, the eNodeB
6 DL performs downlink scheduling on GBR bearers based
Asynchr on the MBR and GBR. If this option is deselected, the
TDLBF eNodeB performs downlink scheduling on GBR
D-00200 onous
HARQ bearers based on the GBR only. This option applies
5 only to LTE FDD and LTE TDD.
LBFD-0 Optimiz
60101 ation of MbrDlSchSwitch: Indicates whether the eNodeB
Periodic performs downlink scheduling based on MBR. If this
LBFD-0 and option is selected, the eNodeB prioritizes UEs based
60103 / Aperiodi on the MBRs during downlink scheduling. This
TDLBF c CQI parameter applies only to LTE TDD.
D-08010 Reportin
2 UeAmbrDlSchSwitch: Indicates whether the eNodeB
g
performs downlink scheduling based on per UE
LEOFD- Enhance aggregate maximum bit rates (UE-AMBRs). If this
111305 d DL option is selected, the eNodeB prioritizes UEs based
LEOFD- Frequen on the UE-AMBRs during downlink scheduling. This
111307 cy option applies only to LTE TDD.
TDLOF Selectiv
e EpfEnhancedSwitch: Indicates whether to enable
D-12110
Scheduli enhanced proportional fair (EPF) enhancement for
5
ng scheduling. EPF enhancement for scheduling is
enabled only if this option is selected. This option
Virtual
applies only to LTE FDD and LTE TDD.
4T4R
eMIMO AperiodicCqiTrigOptSwitch: Indicates whether to
optimize triggering of aperiodic CQI reporting. If this
PRRC option is selected, a UE performing initial access
and triggers aperiodic CQI reporting based on related
DRX trigger conditions after the DLMAC instance has been
Policy established for 200 ms and the eNodeB receives
for MSG5. Consider that aperiodic CQI reporting is
Public triggered by invalid CQI reports in eight consecutive
Safety CQI reporting periods. If cyclic redundancy check
(CRC) on aperiodic CQI reports fails, aperiodic CQI
reporting is not repeatedly triggered when DRX is
enabled; or aperiodic CQI reporting is triggered after
eight TTIs when DRX is disabled. If this option is
deselected, a UE performing initial access triggers

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 142


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

aperiodic CQI reporting based on related trigger


conditions after the DLMAC instance has been
established for 200 ms. Consider that aperiodic CQI
reporting is triggered by invalid CQI reports in eight
consecutive CQI reporting periods. If CRC on
aperiodic CQI reports fails, aperiodic CQI reporting is
triggered after eight TTIs, regardless of the DRX
status. This option applies only to LTE FDD and LTE
TDD.
VoipTbsBasedMcsSelSwitch: Indicates whether the
modulation and coding scheme (MCS) index is
selected based on the transport block size (TBS) in
downlink scheduling for VoLTE services. The MCS
index is selected based on the TBS in downlink
dynamic scheduling for VoLTE services only if this
option is selected. This option applies only to LTE
FDD and LTE TDD.
PagingInterfRandSwitch: Indicates whether to enable
interference randomization for paging messages. If
this option is selected, interference randomization is
enabled for paging messages. This option applies only
to LTE FDD and LTE TDD.
DlSingleUsrMcsOptSwitch: Indicates conditions for
lowering the MCS index for a single UE. If this option
is selected, the MCS index can be lowered for a UE if
the UE is the only UE to be scheduled in a
transmission time interval (TTI). If this option is
deselected, the MCS index can be lowered for a UE if
the threshold for the function of lowering the MCS
index to increase the number of RBs is reached and
the UE is the only UE to be scheduled in a TTI. This
option applies only to LTE FDD and LTE TDD.
UeSigMcsEnhanceSwitch: Indicates whether to
enable MCS optimization for UE signaling. If this
option is selected, MCS optimization for UE signaling
is enabled. For LTE FDD, the MCS index for UE
signaling is the same as the MCS index for data. For
LTE TDD, the MCS index for UE signaling is lowered
based on the MCS index for data. If this option is
deselected, a fixed low MCS index is used for UE
signaling. This option applies only to LTE FDD and
LTE TDD.
SubframeSchDiffSwitch: Indicates whether to
increase the number of UEs scheduled in subframes 3
and 8 when uplink-downlink configuration 2 is used.
If this option is selected, the number of UEs scheduled

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 143


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

in subframes 3 and 8 is increased when uplink-


downlink configuration 2 is used. If this option is
deselected, the scheduling policy used in subframes 3
and 8 is the same as that used in other downlink
subframes when uplink-downlink configuration 2 is
used. This option applies only to LTE TDD.
TailPackagePriSchSwitch: Indicates whether to enable
scheduling of downlink connected tail packages in the
bearer. If this option is selected, the connected tail
package is scheduled preferentially in the next TTI,
which reduces the delay and increases the
transmission rate. If this option is deselected, the
scheduling policy of the connected tail package is the
same as other downlink subframes. This option
applies only to LTE TDD.
SIB1InterfRandSwitch: Indicates whether to enable
SIB1 interference randomization. If this option is
selected, interference randomization is enabled for
SIB1. This option applies only to LTE TDD.
FreqSelJudgeIgnorDopplerSwitch: Indicates whether
to ignore Doppler conditions. If this option is selected,
Doppler conditions are ignored during frequency
selective channel determination. If this option is
deselected, Doppler conditions are considered during
frequency selective channel determination. This
parameter applies only to LTE FDD.
EnhExtQCISpsSchSwitch: Indicates whether to
enable semi-persistent scheduling during talk spurts of
PTT services with standardized QCI 65, standardized
QCI 66, or an enhanced extended QCI. If this option
is selected, semi-persistent scheduling is applied. If
this option is deselected, dynamic scheduling is
applied. This option applies only to LTE FDD and
LTE TDD.
DlVoipBundlingSwitch: Indicates whether to enable
active packet bundling for downlink VoLTE services.
Active packet bundling is enabled for downlink
VoLTE services only if this option is selected. If this
option is selected, PDCCH resources can be saved for
downlink data services or uplink services, thereby
increasing the VoLTE capacity for VoLTE services or
increasing the throughput of data services in mixed
service scenarios. However, the delay in VoLTE voice
packet scheduling will increase in the downlink and
MOSs may decrease. You are advised to deselect this
option if you prefer VoLTE performance and do not

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 144


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

expect MOS reduction. This option applies only to


LTE FDD and LTE TDD.
DlPacketLenAwareSchSw: Indicates whether to
enable packet length awareness performance
optimization in the downlink. Packet length awareness
performance optimization is enabled in the downlink
only if this option is selected. This option applies only
to LTE FDD and LTE TDD.
RLCArqFeedbackEnhancedSwitch: Indicates whether
to modify HARQ feedback results based on RLC
status reports when uplink-downlink configuration 2
is used. If this option is selected, the eNodeB modifies
HARQ feedback results based on RLC status reports
after receiving the reports. This prevents unnecessary
HARQ retransmissions. This option applies only to
LTE TDD.
PaReconfigOptSwitch: Indicates whether to enable PA
reconfiguration optimization. The optimization is
enabled when this option is selected. This option
applies only to LTE FDD and LTE TDD.
RankRapidRptSwitch: Indicates whether to enable fast
rank reporting. If this option is selected, an aperiodic
CQI reporting is immediately triggered after
successful network access. If this option is deselected,
an aperiodic CQI reporting is not immediately
triggered after successful network access. This option
applies only to LTE FDD and LTE TDD.
DlRLCStateReportSchDelaySw: Indicates whether to
enable optimization on the delay-based scheduling of
downlink RLC status reports. The optimization is
enabled when this option is selected. This option
applies only to LTE FDD and LTE TDD.
SmallPktMcsSelectAlgoSw: Indicates whether to
enable MCS selection for small packets. If this option
is selected, the scheduler selects an MCS with a lower
index based on the amount of data to be initially
transmitted and the allocated TBS in each TTI on
condition that the allocated TBS can carry the data.
The function is enabled only if this option is selected.
This option applies only to LTE FDD and LTE TDD.
SRB0SplitSchSw: Indicates whether to enable
separate scheduling of SRB0 and contention
resolution MCE. If this option is selected, SRB0 and
contention resolution MCE are separately scheduled.
This option applies only to LTE FDD and LTE TDD.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 145


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

BfUserPairPriorSwitch: Indicates whether to


preferentially allocate resources to paired
beamforming UEs for UE pairing features such as MU
beamforming and DMIMO. If this option is selected,
the eNodeB preferentially allocates resources to
paired beamforming UEs for UE pairing features such
as MU beamforming and DMIMO. This option
applies only to LTE TDD.

HarqAllocOptSwitch: Indicates whether to optimize


the allocation of HARQ processes. If this option is
selected, the downlink UE rate increases. This option
takes effect only when DMIMO or massive MIMO is
enabled. This option applies only to LTE TDD.

Pusch32Switch: Indicates whether to enable the


PUSCH 3-2 feedback mode. If this option is selected,
UEs that support the PUSCH 3-2 feedback mode use
this mode to aperiodically report CQIs. If this option
is deselected, the mode cannot be used. This option
applies only to LTE FDD.

DlPreciseAmbrCtrlSwitch: Indicates whether to


enable precise downlink AMBR control. If this option
is selected, a more accurate optimization algorithm
applies to the AMBR control, which achieves more
accurate AMBR control. If this option is deselected,
the original AMBR control algorithm is used. This
option applies only to LTE FDD and LTE TDD.
GUI Value Range: FreqSelSwitch(FreqSelSwitch),
SpsSchSwitch(SpsSchSwitch),
MBSFNShutDownSwitch(MBSFNShutDownSwitch),
NonGbrBundlingSwitch(NonGbrBundlingSwitch),
EnAperiodicCqiRptSwitch(EnAperiodicCqiRptS-
witch), DlMbrCtrlSwitch(DlMbrCtrlSwitch),
MbrDlSchSwitch(MbrDlSchSwitch),
UeAmbrDlSchSwitch(UeAmbrDlSchSwitch),
EpfEnhancedSwitch(EpfEnhancedSwitch),
AperiodicCqiTrigOptSwitch(AperiodicCqiTrigOptS-
witch), VoipTbsBasedMcsSelS-
witch(VoipTbsBasedMcsSelSwitch),
PagingInterfRandSwitch(PagingInterfRandSwitch),
DlSingleUsrMcsOptSwitch(DlSingleUsrMcsOptS-
witch), SubframeSchDiffSwitch(SubframeSchDiffS-
witch), TailPackagePriSchS-
witch(TailPackagePriSchSwitch),
UeSigMcsEnhanceSwitch(UeSigMcsEnhanceSwitch),
FreqSelJudgeIgnorDopplerSwitch(FreqSelJudgeIgnor-
DopplerSwitch),

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 146


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

SIB1InterfRandSwitch(SIB1InterfRandSwitch),
EnhExtQCISpsSchSwitch(EnhExtQCISpsSchSwitch),
DlVoipBundlingSwitch(DlVoipBundlingSwitch),
DlPacketLenAwareSchSw(DlPacketLenAwar-
eSchSw), RLCArqFeedbackEnhanced-
Switch(RLCArqFeedbackEnhancedSwitch),
PaReconfigOptSwitch(PaReconfigOptSwitch),
RankRapidRptSwitch(RankRapidRptSwitch),
DlRLCStateReportSchDe-
laySw(DlRLCStateReportSchDelaySw),
SmallPktMcsSelectAlgoSw(SmallPktMcsSelectAl-
goSw), SRB0SplitSchSw(SRB0SplitSchSw),
BfUserPairPriorSwitch(BfUserPairPriorSwitch),
HarqAllocOptSwitch(HarqAllocOptSwitch),
Pusch32Switch(Pusch32Switch),
DlPreciseAmbrCtrlSwitch(DlPreciseAmbrCtrlSwitch)
Unit: None
Actual Value Range: FreqSelSwitch, SpsSchSwitch,
MBSFNShutDownSwitch, NonGbrBundlingSwitch,
EnAperiodicCqiRptSwitch, DlMbrCtrlSwitch,
MbrDlSchSwitch, UeAmbrDlSchSwitch,
EpfEnhancedSwitch, AperiodicCqiTrigOptSwitch,
VoipTbsBasedMcsSelSwitch, PagingInterfRand-
Switch, DlSingleUsrMcsOptSwitch,
SubframeSchDiffSwitch, TailPackagePriSchSwitch,
UeSigMcsEnhanceSwitch, FreqSelJudgeIgnorDop-
plerSwitch, SIB1InterfRandSwitch,
EnhExtQCISpsSchSwitch, DlVoipBundlingSwitch,
DlPacketLenAwareSchSw, RLCArqFeedbackEnhan-
cedSwitch, PaReconfigOptSwitch,
RankRapidRptSwitch, DlRLCStateReportSchDe-
laySw, SmallPktMcsSelectAlgoSw, SRB0SplitSchSw,
BfUserPairPriorSwitch, HarqAllocOptSwitch,
Pusch32Switch, DlPreciseAmbrCtrlSwitch
Default Value: FreqSelSwitch:Off, SpsSchSwitch:Off,
MBSFNShutDownSwitch:Off, NonGbrBundlingS-
witch:Off, EnAperiodicCqiRptSwitch:Off,
DlMbrCtrlSwitch:Off, MbrDlSchSwitch:Off,
UeAmbrDlSchSwitch:Off, EpfEnhancedSwitch:Off,
AperiodicCqiTrigOptSwitch:On, VoipTbsBasedMcs-
SelSwitch:On, PagingInterfRandSwitch:Off,
DlSingleUsrMcsOptSwitch:Off, SubframeSchDiffS-
witch:Off, TailPackagePriSchSwitch:Off,
UeSigMcsEnhanceSwitch:Off, FreqSelJudgeIgnor-
DopplerSwitch:Off, SIB1InterfRandSwitch:On,
EnhExtQCISpsSchSwitch:Off, DlVoipBundlingS-
witch:Off, DlPacketLenAwareSchSw:Off,
RLCArqFeedbackEnhancedSwitch:Off,

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 147


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd
PaReconfigOptSwitch:Off, RankRapidRptSwitch:Off,
DlRLCStateReportSchDelaySw:Off,
SmallPktMcsSelectAlgoSw:Off,
SRB0SplitSchSw:Off, BfUserPairPriorSwitch:Off,
HarqAllocOptSwitch:Off, Pusch32Switch:Off,
DlPreciseAmbrCtrlSwitch:Off

CellRes LocalCe LST None None Meaning: Indicates the local ID of the cell. It uniquely
el llId CELLR identifies a cell within a BS.
ESEL GUI Value Range: 0~255
MOD Unit: None
CELLR
ESEL Actual Value Range: 0~255
Default Value: None

CellRes PMaxCf MOD LBFD-0 Cell Meaning: Indicates whether to configure the
el gInd CELLR 0201803 Selectio maximum TX power of the UE in the intra-frequency
ESEL / n and neighboring cell. If the value of this parameter is not
LST TDLBF Re- specified, the maximum power is subject to the UE
CELLR D-00201 selection capability.
ESEL 803 / Broadca GUI Value Range: NOT_CFG(Not configure),
MLBFD st of CFG(Configure)
-120002 system
37 Unit: None
informat
LBFD-0 ion Actual Value Range: NOT_CFG, CFG
02009 / Default Value: NOT_CFG(Not configure)
TDLBF
D-00200
9/
MLBFD
-120002
29

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 148


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

EutranIn LocalCe ADD None None Meaning: Indicates the ID of the local cell. It uniquely
terNFre llId EUTRA identifies a cell within an eNodeB.
q NINTE GUI Value Range: 0~255
RNFRE
Q Unit: None

LST Actual Value Range: 0~255


EUTRA Default Value: None
NINTE
RNFRE
Q
MOD
EUTRA
NINTE
RNFRE
Q
RMV
CELLE
UTRAN
INTER
NFREQ
RMV
EUTRA
NINTE
RNFRE
Q

EutranIn CellRes ADD LBFD-0 Cell Meaning: Indicates whether to set the reselection
terNFre elPriorit EUTRA 0201803 Selectio priority of the neighboring E-UTRAN frequency. For
q yCfgInd NINTE / n and details about how UEs process frequency priorities
RNFRE TDLBF Re- during cell reselection, see section 5.2.4.1 of 3GPP TS
Q D-00201 selection 36.304 (V12.4.0). This parameter applies only to LTE
MOD 803 FDD and LTE TDD.
EUTRA GUI Value Range: NOT_CFG(Not configure),
NINTE CFG(Configure)
RNFRE Unit: None
Q
Actual Value Range: NOT_CFG, CFG
LST
EUTRA Default Value: NOT_CFG(Not configure)
NINTE
RNFRE
Q

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 149


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes LocalCe ADD None None Meaning: Indicates the local ID of the cell. It uniquely
elUtran llId CELLR identifies a cell within an eNodeB. This parameter
ESELU applies only to LTE FDD and LTE TDD.
TRAN GUI Value Range: 0~255
LST Unit: None
CELLR
ESELU Actual Value Range: 0~255
TRAN Default Value: None
MOD
CELLR
ESELU
TRAN
RMV
CELLR
ESELU
TRAN

UtranNF LocalCe ADD None None Meaning: Indicates the local ID of the cell. It uniquely
req llId UTRAN identifies a cell within an eNodeB. This parameter
NFREQ applies only to LTE FDD and LTE TDD.
LST GUI Value Range: 0~255
UTRAN Unit: None
NFREQ
Actual Value Range: 0~255
MOD
UTRAN Default Value: None
NFREQ
RMV
UTRAN
NFREQ

UtranNF CellRes ADD LBFD-0 Cell Meaning: Indicates whether to set the priority of a cell
req elPriorit UTRAN 0201803 Selectio assigned with the UARFCN used in cell reselection to
yCfgInd NFREQ / n and UTRAN. For details about how UEs process
MOD TDLBF Reselect frequency priorities during cell reselection, see section
UTRAN D-00201 ion / 5.2.4.1 of 3GPP TS 36.304 (V12.4.0). This parameter
NFREQ 803 Cell applies only to LTE FDD and LTE TDD.
Selectio GUI Value Range: NOT_CFG(Not configure),
LST n and
UTRAN CFG(Configure)
Re-
NFREQ selection Unit: None
Actual Value Range: NOT_CFG, CFG
Default Value: NOT_CFG(Not configure)

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 150


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes LocalCe ADD None None Meaning: Indicates the local ID of the cell. It uniquely
elGeran llId CELLR identifies a cell within an eNodeB. This parameter
ESELG applies only to LTE FDD and LTE TDD.
ERAN GUI Value Range: 0~255
LST Unit: None
CELLR
ESELG Actual Value Range: 0~255
ERAN Default Value: None
MOD
CELLR
ESELG
ERAN
RMV
CELLR
ESELG
ERAN

GeranNf LocalCe ADD None None Meaning: Indicates the cell ID of the local cell. It
reqGrou llId GERAN uniquely identifies a cell within an eNodeB. This
p NFREQ parameter applies only to LTE FDD and LTE TDD.
GROUP GUI Value Range: 0~255
LST Unit: None
GERAN
NFREQ Actual Value Range: 0~255
GROUP Default Value: None
MOD
GERAN
NFREQ
GROUP
RMV
GERAN
NFREQ
GROUP

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 151


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

GeranNf BcchGr ADD LBFD-0 Cell Meaning: Indicates a GERAN carrier frequency
reqGrou oupId GERAN 0201803 Selectio group. In the cell reselection procedure, the GERAN
p NFREQ / n and carrier frequencies are organized in groups and the
GROUP TDLBF Re- cell reselection parameters are provided per group of
LST D-00201 selection GERAN carrier frequencies. This parameter applies
GERAN 803 PS Inter- only to LTE FDD and LTE TDD.
NFREQ LOFD-0 RAT GUI Value Range: 0~31
GROUP 01020 / Mobility Unit: None
MOD TDLOF between
D-00102 E- Actual Value Range: 0~31
GERAN
NFREQ 0 UTRAN Default Value: None
GROUP and
GERAN
RMV
GERAN
NFREQ
GROUP

GeranNf CellRes ADD LBFD-0 Cell Meaning: Indicates whether to set the reselection
reqGrou elPriorit GERAN 0201803 Selectio priority of the frequencies in the GERAN carrier
p yCfgInd NFREQ / n and frequency group. For details about how UEs process
GROUP TDLBF Reselect frequency priorities during cell reselection, see section
MOD D-00201 ion / 5.2.4.1 of 3GPP TS 36.304 (V12.4.0). This parameter
GERAN 803 Cell applies only to LTE FDD and LTE TDD.
NFREQ Selectio GUI Value Range: NOT_CFG(Not configure),
GROUP n and CFG(Configure)
Re-
LST selection Unit: None
GERAN
Actual Value Range: NOT_CFG, CFG
NFREQ
GROUP Default Value: NOT_CFG(Not configure)

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 152


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes LocalCe ADD None None Meaning: Indicates the local ID of the cell. It uniquely
elCdma llId CELLR identifies a cell within an eNodeB. This parameter
2000 ESELC applies only to LTE FDD and LTE TDD.
DMA20 GUI Value Range: 0~255
00
Unit: None
LST
CELLR Actual Value Range: 0~255
ESELC Default Value: None
DMA20
00
MOD
CELLR
ESELC
DMA20
00
RMV
CELLR
ESELC
DMA20
00

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 153


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes SysTime ADD LBFD-0 Cell Meaning: Indicates whether to configure the
elCdma CfgInd CELLR 0201803 Selectio CDMA2000 system time information. For details, see
2000 ESELC / n and 3GPP TS 36.331. This parameter applies only to LTE
DMA20 TDLBF Re- FDD and LTE TDD.
00 D-00201 selection GUI Value Range: NOT_CFG(Not configure),
MOD 803 CS CFG(Configure)
CELLR LOFD-0 Fallback Unit: None
ESELC 01035 / to
DMA20 TDLOF CDMA2 Actual Value Range: NOT_CFG, CFG
00 D-00103 000 Default Value: NOT_CFG(Not configure)
LST 5 1xRTT
CELLR LBFD-0 Broadca
ESELC 02009 / st of
DMA20 TDLBF system
00 D-00200 informat
9 ion
LOFD-0 Enhance
01090 / d CS
TDLOF Fallback
D-00109 to
0 CDMA2
LOFD-0 000
01021 / 1xRTT
TDLOF PS Inter-
D-00102 RAT
1 Mobility
TDLOF between
D-00109 E-
1 UTRAN
and
LOFD-0 CDMA2
01111 000
CS
Fallback
to
CDMA2
000
1xRTT
Based
on
Frequen
cy-
specific
Factors
PS
Mobility
from E-

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 154


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

UTRAN
to
CDMA2
000
HRPD
Based
on
Frequen
cy-
specific
Factors

TASM CLKSY SET MRFD- BTS Meaning: Indicates the clock synchronization mode of
NCMO CLKSY 210501 Clock a BS, which can be frequency synchronization or time
DE NCMO synchronization.
DE GUI Value Range: FREQ(FREQ), TIME(TIME),
DSP HYBRID(HYBRID)
CLKST Unit: None
AT
Actual Value Range: FREQ, TIME, HYBRID
LST
CLKSY Default Value: FREQ(FREQ)
NCMO
DE

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 155


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes HrpdPar ADD LBFD-0 Cell Meaning: Indicates whether the eNodeB includes the
elCdma aCfgInd CELLR 0201803 Selectio information about CDMA2000 HRPD in SIB8. If this
2000 ESELC / n and parameter is set to CFG, the eNodeB includes the
DMA20 TDLBF Re- parametersHRPD field in SIB8. If this parameter is set
00 D-00201 selection to NOT_CFG, the eNodeB does not include the
MOD 803 PS Inter- parametersHRPD field in SIB8. For details, see 3GPP
CELLR LOFD-0 RAT TS 36.331. This parameter applies only to LTE FDD
ESELC 01021 / Mobility and LTE TDD.
DMA20 TDLOF between GUI Value Range: NOT_CFG(Not configure),
00 D-00102 E- CFG(Configure)
LST 1 UTRAN Unit: None
CELLR LBFD-0 and
CDMA2 Actual Value Range: NOT_CFG, CFG
ESELC 02009 /
DMA20 TDLBF 000 Default Value: NOT_CFG(Not configure)
00 D-00200 Broadca
9 st of
LOFD-0 system
01111 informat
ion
PS
Mobility
from E-
UTRAN
to
CDMA2
000
HRPD
Based
on
Frequen
cy-
specific
Factors

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 156


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes HrpdCel ADD LBFD-0 Cell Meaning: Indicates whether to set the parameters
elCdma lReselec CELLR 0201803 Selectio related to cell reselection to CDMA2000 HRPD. This
2000 tParamC ESELC / n and parameter applies only to LTE FDD and LTE TDD.
fgInd DMA20 TDLBF Re- GUI Value Range: NOT_CFG(Not configure),
00 D-00201 selection CFG(Configure)
MOD 803 PS Inter- Unit: None
CELLR LOFD-0 RAT
ESELC 01021 / Mobility Actual Value Range: NOT_CFG, CFG
DMA20 TDLOF between Default Value: NOT_CFG(Not configure)
00 D-00102 E-
LST 1 UTRAN
CELLR LBFD-0 and
ESELC 02009 / CDMA2
DMA20 TDLBF 000
00 D-00200 Broadca
9 st of
system
informat
ion

CellRes Cdma1 ADD LBFD-0 Cell Meaning: Indicates whether the eNodeB includes the
elCdma XrttPara CELLR 0201803 Selectio information about CDMA2000 1xRTT in SIB8. If this
2000 CfgInd ESELC / n and parameter is set to CFG, the eNodeB includes the
DMA20 TDLBF Re- parameters1xRTT field in SIB8. If this parameter is
00 D-00201 selection set to NOT_CFG, the eNodeB does not include the
MOD 803 CS parameters1xRTT field in SIB8. For details, see 3GPP
CELLR LOFD-0 Fallback TS 36.331. This parameter applies only to LTE FDD
ESELC 01035 / to and LTE TDD.
DMA20 LOFD-0 CDMA2 GUI Value Range: NOT_CFG(Not configure),
00 01035 000 CFG(Configure)
LST LBFD-0 1xRTT Unit: None
CELLR 02009 / Broadca Actual Value Range: NOT_CFG, CFG
ESELC TDLBF st of
DMA20 D-00200 system Default Value: NOT_CFG(Not configure)
00 9 informat
TDLOF ion
D-00109 Enhance
0/ d CS
LOFD-0 Fallback
01090 to
CDMA2
000
1xRTT

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 157


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

CellRes Cdma1 ADD LBFD-0 Cell Meaning: Indicates whether the parameters applicable
elCdma XrttCell CELLR 0201803 Selectio only for cell reselection to CDMA2000 1xRTT need
2000 ReselCf ESELC / n and to be set. This parameter applies only to LTE FDD
gInd DMA20 TDLBF Re- and LTE TDD.
00 D-00201 selection GUI Value Range: NOT_CFG(Not configure),
MOD 803 CS CFG(Configure)
CELLR LOFD-0 Fallback Unit: None
ESELC 01035 / to
DMA20 TDLOF CDMA2 Actual Value Range: NOT_CFG, CFG
00 D-00103 000 Default Value: NOT_CFG(Not configure)
LST 5 1xRTT
CELLR LBFD-0 Broadca
ESELC 02009 / st of
DMA20 TDLBF system
00 D-00200 informat
9 ion
TDLOF Enhance
D-00109 d CS
0/ Fallback
LOFD-0 to
01090 CDMA2
000
1xRTT

Cdma20 LocalCe ADD None None Meaning: Indicates the cell ID of the local cell. It
00Band llId CDMA2 uniquely identifies a cell within an eNodeB. This
Class 000BA parameter applies only to LTE FDD and LTE TDD.
NDCLA GUI Value Range: 0~255
SS
Unit: None
LST
CDMA2 Actual Value Range: 0~255
000BA Default Value: None
NDCLA
SS
MOD
CDMA2
000BA
NDCLA
SS
RMV
CDMA2
000BA
NDCLA
SS

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 158


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

Cdma20 BandCla ADD LBFD-0 Cell Meaning: Indicates the neighboring CDMA2000 band
00Band ss CDMA2 0201803 Selectio class. Signals on a frequency within the band class can
Class 000BA / n and be obtained by UEs. For details, see the
NDCLA TDLBF Re- BandclassCDMA2000 IE defined in 3GPP 36.331.
SS D-00201 selection This parameter applies only to LTE FDD and LTE
LST 803 CS TDD.
CDMA2 LOFD-0 Fallback GUI Value Range: bc0, bc1, bc2, bc3, bc4, bc5, bc6,
000BA 01035 / to bc7, bc8, bc9, bc10, bc11, bc12, bc13, bc14, bc15,
NDCLA TDLOF CDMA2 bc16, bc17, bc18, bc19, bc20, bc21
SS D-00103 000 Unit: None
MOD 5 1xRTT
Actual Value Range: bc0, bc1, bc2, bc3, bc4, bc5, bc6,
CDMA2 LOFD-0 Enhance bc7, bc8, bc9, bc10, bc11, bc12, bc13, bc14, bc15,
000BA 01090 / d CS bc16, bc17, bc18, bc19, bc20, bc21
NDCLA TDLOF Fallback
SS D-00109 to Default Value: None

RMV 0 CDMA2
CDMA2 000
000BA 1xRTT
NDCLA
SS

Cdma20 Cdma20 ADD LBFD-0 Cell Meaning: Indicates whether to configure cell
00Band 001Xrtt CDMA2 0201803 Selectio reselection priorities for CDMA2000 1xRTT band
Class CellRes 000BA / n and class. If this parameter is set to NOT_CFG, the cell
elInd NDCLA TDLBF Re- reselection priorities are not delivered in the system
SS D-00201 selection information. This parameter applies only to LTE FDD
MOD 803 CS and LTE TDD.
CDMA2 LOFD-0 Fallback GUI Value Range: NOT_CFG(Not configure),
000BA 01035 / to CFG(Configure)
NDCLA TDLOF CDMA2 Unit: None
SS D-00103 000
5 1xRTT Actual Value Range: NOT_CFG, CFG
LST
CDMA2 LOFD-0 Enhance Default Value: NOT_CFG(Not configure)
000BA 01090 / d CS
NDCLA TDLOF Fallback
SS D-00109 to
0 CDMA2
000
1xRTT

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 159


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 7 Parameters

MO Parame MML Feature Feature Description


ter ID Comma ID Name
nd

Cdma20 Cdma20 ADD LBFD-0 Cell Meaning: Indicates whether to configure cell
00Band 00Hrpd CDMA2 0201803 Selectio reselection priorities for CDMA2000 HRPD band
Class CellRes 000BA / n and class. If this parameter is set to NOT_CFG, the cell
elInd NDCLA TDLBF Re- reselection priorities are not delivered in the system
SS D-00201 selection information. This parameter applies only to LTE FDD
MOD 803 PS Inter- and LTE TDD.
CDMA2 LOFD-0 RAT GUI Value Range: NOT_CFG(Not configure),
000BA 01021 / Mobility CFG(Configure)
NDCLA TDLOF between Unit: None
SS D-00102 E-
1 UTRAN Actual Value Range: NOT_CFG, CFG
LST
CDMA2 LOFD-0 and Default Value: NOT_CFG(Not configure)
000BA 01111 CDMA2
NDCLA 000
SS PS
Mobility
from E-
UTRAN
to
CDMA2
000
HRPD
Based
on
Frequen
cy-
specific
Factors

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 160


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 8 Counters

8 Counters

Table 8-1 Counters


Counter ID Counter Name Counter Feature ID Feature Name
Description

1526726884 L.Paging.S1.Rx Number of received Multi-mode: None Paging


paging messages GSM: None Paging
over the S1
interface in a cell UMTS: None
LTE: LBFD-002011
TDLBFD-002011

1526726885 L.Paging.UU.Att Number of UEs Multi-mode: None Paging


contained in paging GSM: None Paging
messages
transmitted over the UMTS: None Dynamic DRX
Uu interface in a LTE: LBFD-002011
cell TDLBFD-002011
LOFD-00110501

1526726886 L.Paging.UU.Succ Number of Multi-mode: None Paging


Successful Paging GSM: None Paging
Responses from the
UE in a Cell UMTS: None
LTE: LBFD-002011
TDLBFD-002011

1526727212 L.Paging.Dis.Num Number of Multi-mode: None Paging


discarded paging GSM: None Paging
messages from the
MME to UEs UMTS: None
LTE: LBFD-002011
TDLBFD-002011

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 161


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 8 Counters

Counter ID Counter Name Counter Feature ID Feature Name


Description

1526728337 L.Paging.UU.SIUp Number of paging Multi-mode: None Paging


date messages GSM: None Paging
transmitted due to
system information UMTS: None
changes LTE: LBFD-002011
TDLBFD-002011

1526728521 L.Paging.Dis.PchC Number of paging Multi-mode: None Paging


ong messages discarded GSM: None Paging
due to paging
channel congestion UMTS: None
LTE: LBFD-002011
TDLBFD-002011

1526729280 L.Signal.Num.SIB1 Times of ETWS- Multi-mode: None Earthquake and


.ETWS induced SIB1 GSM: None Tsunami Warning
changes System (ETWS)
UMTS: None
Earthquake and
LTE: Tsunami Warning
LBFD-002029 System(ETWS)
TDLBFD-002029 Broadcast of system
LBFD-002009 information
TDLBFD-002009 Broadcast of system
information

1526729665 L.Paging.S1.Rx.PL Number of received Multi-mode: None Paging


MN paging messages GSM: None Paging
over the S1
interface for a UMTS: None RAN Sharing with
specific operator in Common Carrier
LTE: LBFD-002011
a cell RAN Sharing with
TDLBFD-002011 Common Carrier
TDLOFD-001036 RAN Sharing with
LOFD-001036 Dedicated Carrier
LOFD-001037 RAN Sharing with
Dedicated Carrier
TDLOFD-001037
Hybrid RAN
LOFD-070206 Sharing

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 162


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 8 Counters

Counter ID Counter Name Counter Feature ID Feature Name


Description

1526730140 L.Paging.UU.Succ. Number of paging Multi-mode: None Paging


CSFB responses for CSFB GSM: None Paging
received from UEs
in a cell UMTS: None CS Fallback to
LTE: LBFD-002011 UTRAN
TDLBFD-002011 CS Fallback to
UTRAN
LOFD-001033
CS Fallback to
TDLOFD-001033 GERAN
LOFD-001034 CS Fallback to
TDLOFD-001034 GERAN
LOFD-001035 CS Fallback to
TDLOFD-001035 CDMA2000 1xRTT
CS Fallback to
CDMA2000 1xRTT

1526730145 L.Paging.S1.Rx.CS Number of received Multi-mode: None Paging


paging messages GSM: None Paging
with the IE CN
DOMAIN set to CS UMTS: None CS Fallback to
over the S1 LTE: LBFD-002011 UTRAN
interface in a cell TDLBFD-002011 CS Fallback to
UTRAN
LOFD-001033
CS Fallback to
TDLOFD-001033 GERAN
LOFD-001034 CS Fallback to
TDLOFD-001034 GERAN
LOFD-001035 CS Fallback to
TDLOFD-001035 CDMA2000 1xRTT
CS Fallback to
CDMA2000 1xRTT

1526730562 L.Paging.UU.Num Number of paging Multi-mode: None Paging


messages sent over GSM: None Paging
the Uu interface in
a cell UMTS: None
LTE: LBFD-002011
TDLBFD-002011

1526746004 L.Paging.S1.Rx.eD Number of received Multi-mode: None Paging


RX eDRX paging GSM: None Paging
messages over the
S1 interface in a UMTS: None LTE Supporting
cell LTE: LBFD-002011 eDRX in Idle Mode
TDLBFD-002011
LEOFD-121203

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 163


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 9 Glossary

9 Glossary

For the acronyms, abbreviations, terms, and definitions, see Glossary.

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 164


Copyright Huawei Technologies Co., Ltd.
eRAN
Idle Mode Management Feature Parameter Description 10 Reference Documents

10 Reference Documents

This chapter lists the reference documents related to idle mode management:
1. 3GPP TS 36.331, "RRC Protocol Specification"
2. 3GPP TS 23.401, "General Packet Radio Service (GPRS) enhancements for Evolved
Universal Terrestrial Radio Access Network (E-UTRAN) access"
3. 3GPP TS 36.101, "User Equipment (UE) radio transmission and reception"
4. 3GPP TS 22.011, "Service accessibility"
5. 3GPP TS 23.122, "Non-Access-Stratum (NAS) functions related to Mobile Station (MS)
in idle mode"
6. 3GPP TS 36.304, "User Equipment (UE) procedures in idle mode"
7. 3GPP TS 36.300, "E-UTRAN Overall description"
8. Flexible User Steering Feature Parameter Description
9. Carrier Aggregation Feature Parameter Description
10. Access Class Control Feature Parameter Description
11. Scheduling Feature Parameter Description

Issue 01 (2017-03-08) Huawei Proprietary and Confidential 165


Copyright Huawei Technologies Co., Ltd.

Anda mungkin juga menyukai