MAIN BENEFITS
Productivity The Mechanised Bolting Unit (MBU) utilises a single
feed rail concept that means that the unit never moves off the
drilled bolt hole - this maximises the hole alignment capabilities
when installing the bolt and ensures faster installation times.
Rock Drill The COP 1132 rock drill is optimised for bolt hole drilling,
with its light weight and high frequency it reduces loads on the
boom whilst achieving superior penetration rate. For larger hole
diameters required for some friction bolt types or harder rock
conditions the optional COP 1435 delivers the hitting power
needed to get the job done.
2
Optional mesh handling arm
3
BOLTEC M
SAFE BOLTING
SAFETY AND QUALITY OF BOLT INSTALLATION IS OUR FOCUS. THE BOLTEC M
IS DESIGNED WITH STANDARD AND OPTIONAL FEATURES THAT ENSURE
THESE GOALS ARE MET.
+ SAFETY
Mechanised bolting removes the operator from the potential danger
area of unsupported ground. All drilling and bolt installation is controlled
from the operator station under a FOPS canopy or optional ROPS/FOPS air
conditioned cabin.
+ OPERATOR COMFORT
The operator position affords excellent visibility of the bolting operation
as well as when tramming the vehicle. The operator area is spacious and
features a swingable operator seat for driving and bolting. The optional
ROPS/FOPS air conditioned cabin enhances the operators comfort
especially in extreme temperatures or dusty conditions.
4
A = BOLTEC M C = OPTION
TECHNICAL SPECIFICATIONS
B = BOLTEC M D = STANDARD
Size of face plates, round, diameter, max 200 mm Cable reel with limiting switch
Bolt length from 1.5 m to 3.5 m Electrical outlet, main supply voltage 16Amp 3-phase (16A or 32A socket size)
- not for 1000V
Swellex, Mn 12, Mn 16, Mn 24
Extra transformer 3-phase 15kVA capacity with 230V and 400V outlet
Split-Set, SS39, SS46
(16A or 32A socket size)
Mechanical anchor bolts, CT, Kiruna, including boltrotator PC4 or PC5 Plug/Socket
Rebar - manual resin / cement cartridge, including boltrotator
Spotlight, 1x70 W, 24 V
Rebar - resin cartridge injection system, automatic, including boltrotator
Illuminated stairs for platform (LED)
Rebar - Cement injection system, manual mixing
REbar - Cement injection system, automatic mixing with bulk cement silo 1 000 kg
Hose injection system for resin cartridges CARRIER A B
Dual bolt lengths* Deutz TCD 2013 L4 120kW 4 cylinder Tier 3 / Stage IIIA diesel engine
Dual bolt types Deutz TCD 4.1 115kW 4 cylinder Tier 4 final / Stage IV diesel engine
Extension drilling kit Articulated 40 steering angle
Screen handling arm Four wheel drive
*2nd bolt length no less than 70% length of maximum bolt length Hot climate tramming kit
Electrical system 24 V
Batteries 2 x 125 Ah
HYDRAULIC SYSTEM A B
Automatic differential lock on front axle, limited slip
Low oil level indicator
Tyres, 12.00 R24
Oil temperature meter
Clearance outside axles rear 13
Filtration 16 m
Front and rear hydraulic jacks
Oil filter indicator
Fuel tank volume 4 cylinder engine 110 L
Mineral hydraulic oil
Central lubrication system
Electric oil filling pump
Tramming lights, rear 4 x 40W LED
Biodegradable hydraulic oil
Tramming lights, rear 2 x 40W LED + 2 x 70W Halogen
Hydraulic oil thermostat
Working lights 2 x 320W LED 24V DC
Hydraulic oil leakage detection and shut-down system
Illuminated stairs for platform
Hydraulic oil fine particulate and water filtration system
(not in conjunction with bulk cement system) Central grease point
Fire extinguisher
Fire suppression system ANSUL -manual release
CONTROL SYSTEM A B Fire suppression system ANSUL -Automatic release (checkfire)
Rig Control System (RCS) Fire suppression system ANSUL - Automatic release with CO2 in electrical cabinet
Bolt quality log (BQL)
Bolt plan navigation
Rig Remote Access (RRA)
Bolt angle indication
Direct Hydraulic Control System (DCS)
5
A = BOLTEC M C = OPTION
TECHNICAL SPECIFICATIONS
B = BOLTEC M D = STANDARD
TRAMMING SPEED
On flat ground (Rolling resistance 0.05) >15
On incline 1:8 >5
6
TECHNICAL SPECIFICATIONS
1 197
571
13 10 19
1 238
13 937
Dimension illustration (Optional equipment mounted).
9 390
3 490
4 913
www.atlascopco.com
EC
2 230
EC
30
R
70
50
20
R 1 500
41
R4
1
24 3 26 2
2
100
0
26
1
3
24
3
2
71
Turning radius.
7
COMMITTED TO SUSTAINABLE PRODUCTIVITY
We stand by our responsibilities towards our customers,
towards the environment and the people around us.
www.atlascopco.com
9851 2202 01i 2016 rebro, Sweden. Legal Notice Copyright 2014, Atlas Copco Rock Drills AB, rebro, Sweden. All product names in this publication are trademarks of Atlas Copco. Any unauthorized use or copying
of the contents or any part thereof is prohibited. Illustrations and photos may show equipment with optional extras. No warranty is made regarding specifications or otherwise. Specifications and equipment are subject
to change without notice. Consult your Atlas Copco Customer Center for specific information.