Customer Benefits
Trip circuit and Trip coil su-
pervision relay
Choice of pre-closing and
Post-closing supervision
Simple and robust con-
struction
Draw out type case
Completely dust proof by
IP5X class protection
GRID
1
Type VAX / MVAXM
Application
Post-closing or continuous supervision of the trip circuit of cir-
cuit breakers
General description
Type VAX and MVAXM relays are of simple and robust con-
struction. They are arranged to initiate an audible alarm and
Type VAX 31 and MVAXM 31 relays Under healthy conditions
visual indication if the trip circuit of a circuit breaker fails or the
with the consist of three units connected as shown in figures
breaker tripping mechanism does not operate
2(a) and 2(b), circuit breaker closed, units A and C are ener-
giesed and the operation is the same as that of type VAX 21
Two versions of type VAX and MVAXM relays are available.
and MVAXM 21 relays. When the circuit breaker is open unit B
Type VAX 21 and MVAXM 21 relays monitor the trip circuit only
is also energised via the normally closed auxiliary switch of the
when the circuit breaker is closed (post-closing supervision
circuit- breaker and unit C is held-in by contact B-1 Unit B will
only) while type VAX 31 and MVAXM 31 relays monitor the trip
detect trip circuit abnormalities with the circuit breaker open in
circuit continuously (both pre-closing and post-closing supervi-
a similar manner as unit A with the circuit breaker closed
sion). Both versions detect the following conditions.
2
Type VAX / MVAXM
Burdens
For VAX
DC Voltage 24 30 48/50 110/125 220/250
Maximum watts Trip supply 0.52 0.56 0.62 1.56 3.13
Alarm Supply 0.37 0.38 0.44 1.12 2.6
For MVAXM
Contact ratings
3
Type VAX / MVAXM
The approximate gross weights given above are inclusive of cartons, mounting appendages and terminal details.
The relays comply fully with requirements of IS 3231 and are suitable for use in normal tropical environments.
MVAXM 31
Size 4 Midos
4
Type VAX / MVAXM
5
Type VAX / MVAXM
completeness of such data or the achievements of any projected performance criteria where these are indicated. No liability is accepted for any reliance placed upon the information contained in this brochure. Alstom reserves the right to
Alstom logo and any alternative version thereof are trademarks and service marks of Alstom. The other names mentioned, registered or not, are the property of their respective companies. The technical and other data contained in
the document are provided for information only. Neither ALSTOM, its officers nor employees accept responsibility for or should be taken as making any representation or warranty (whether express or implied) as to the accuracy or
> Setting ranges INFORMATION REQUIRED
WITH ORDER
Tap setting (Is) 20%, 40% 80%, 160% In.
10%, 20%, 40%, 80% In. Relay type
5%, 10%, 20%, 40% In. CT Secondary rating
Setting range
Figure 3 : Case and panel cut-out dimensions for case 1/2N (all dimensions in mm)
Current setting Auxiliary supply voltage
multiplier 1-2x tap setting
This gives effective
setting ranges of: 71 26
4 holes 4.4 23.5
20 - 320% In. Figure 3
10 - 160% In. Case outline: size 3
5 - 80% In. 168 159
Push button
projection 10 max
Panel cut-out:
> Operating time 73 Flush mounting fixing details
32
ORMATION
Operate time REQUIRED
<10ms
212 25 min.
HReset
ORDER
time <15ms, typically 12ms 177
157 max.
ype
>ondary rating
Contacts 77
Reset
y supply voltage
MCTI 40 2 normally open or 1 normally Figure 4 : Case and panel cut-out dimensions for case 1D (all dimensions in mm)
open and 1 normally closed per
phase or earth fault element 52
71 26
4 holes 4.4 97 4 holes 4.4
23.5
3 Figure 4 23.5
Push button
projection 10 max
Panel cut-out: Push button
Current Make and carry Make and carry73 Break Flush mounting fixing details projection 10 max. 99
Panel cut-out:
continuously for 0.2s Flush mounting fixing details.
GRID
www.grid.alstom.com
103 155
Flush mounting. 11 Flush mounting. 11 6