OUTDOOR UNIT
HFC No. OB377
SERVICE MANUAL utilized
R410A
REVISED EDITION-H
Models
MXZ-2A30VA - E1 MXZ-4A71VA - E2
MXZ-2A30VA - E2 MXZ-4A71VA - E3
MXZ-2A40VA - E1 MXZ-4A71VA - E4
MXZ-2A40VA - E2 MXZ-4A71VA - E5
MXZ-2A52VA - E1 MXZ-4A71VA - E6
MXZ-2A52VA - E2 MXZ-4A71VA - E7
MXZ-3A54VA - E1 MXZ-4A80VA - E1
MXZ-3A54VA - E2 MXZ-4A80VA - E2
MXZ-3A54VA - E3 MXZ-5A100VA - E1
MXZ-3A54VA - E4 Indoor unit service manual
MSZ-FA•VA Series (OB371)
MXZ-3A54VA - E5
MSZ-GA•VA Series (OB378, OB388)
MXZ-3A54VA - E6 MSZ-CB•VA Series (OB441)
MXZ-3A54VA - E7 MSZ-GC•VA Series (OBH468)
MSZ-GE•VA Series (OBH515)
MXZ-4A71VA - E1
MSZ-FD•VA Series (OBH488)
CONTENTS
Revision B :
• MXZ-2A30VA- E1 and MXZ-2A40VA- E2 have been added.
• “Check of HPS” has been corrected.
• RoHS PARTS LIST has been added.
Revision C :
• MXZ-2A52VA- E2 , MXZ-3A54VA- E3 , MXZ-4A71VA- E3 , MXZ-4A80VA- E2 and MXZ-5A100VA- E1 have been added.
Revision D:
• MXZ-3A54VA- E4 , and MXZ-4A71VA- E4 have been added.
• The content of pre-heat control (12-3) has been corrected.
• 5. SPECIFICATION has been corrected.
Revision E:
• MXZ-2A30VA- E1 has been added.
• 4. INDOOR UNITS COMBINATION of MXZ-5A100VA- E2 has been changed.
Revision F:
• MXZ-3A54VA- E5 and MXZ-4A71VA- E5 have been added.
Revision G:
• MXZ-3A54VA- E6 and MXZ-4A71VA- E6 have been added.
Revision H:
• Indoor units combinations for 42 class have been added.
• MXZ-3A54VA- E7 and MXZ-4A71VA- E7 have been added.
1 TECHNICAL CHANGES
MXZ-A26WV - E1 MXZ-3A54VA - E1
1. Indication of capacity has been changed. (BTU kW)
2. Capacity specification has been changed. (Cooling capacity 7.1kW 5.4kW)
3. Dimensions of unit have been changed. (W900 H900 D320 W840 H710 D330)
4. Combinations of connectable indoor units have been changed.
5. Capacity class of connectable indoor units has been changed.
6. Communication system has been changed.
7. Power supply way has been changed (change to supply to outdoor unit).
8. Compressor has been changed. (TNB220FMCH SNB130FLDH1)
9. High-pressure switch has been removed.
10.Outdoor fan motor has been changed. (PM8H60-UA RC0J60-AA)
11.Evaporation temperature thermistor has been removed.
12.Ambient temperature thermistor has been added.
13.New dip switch has been added to the controller board for "Locking the operation "mode
and "Lowering the operating noise "mode.
14.A Quick Clean Kit has been added.
MXZ-A32WV - E1 MXZ-4A71VA - E1
1. Indication of capacity has been changed. (BTU kW)
2. Capacity specification has been changed. (Cooling capacity 8.0kW 7.1kW)
3. Dimensions of unit have been changed. (W900 H900 D320 W840 H710 D330)
4. Combinations of connectable indoor units have been changed.
5. Capacity class of connectable indoor units has been changed.
6. Communication system has been changed.
7. Power supply way has been changed (change to supply to outdoor unit).
8. Compressor has been changed. (TNB220FMCH SNB130FLDH1)
9. High-pressure switch has been removed.
10. Outdoor fan motor has been changed. (PM8H60-UA RC0J60-AA)
11. Evaporation temperature thermistor has been removed.
12. Ambient temperature thermistor has been added.
13. New dip switch has been added to the controller board for "Locking the operation "mode
and "Lowering the operating noise "mode.
14. A Quick Clean Kit has been added.
2
MXZ-A14WV - E2 MXZ-2A40VA - E1
1. Indication of capacity has been changed. (BTU kW)
2. Dimensions of unit have been changed. (W840 H640 D330 W800 H550 D285)
3. Communication system has been changed.
4. Power supply way has been changed (change to supply to outdoor unit).
5. Compressor has been changed. (SNV092FJYH SNB130FKCH)
6. Outdoor fan motor has been changed. (RA6V49 RC0J50-CF)
7. Evaporation temperature thermistor has been removed.
8. Gas pipe temperature thermistor has been removed.
9. Ambient temperature thermistor has been added.
MXZ-A18WV - E2 MXZ-2A52VA - E1
1. Indication of capacity has been changed. (BTU kW)
2. Cooling capacity specification has been changed. (5.4 kW 5.2 kW)
3. Heating capacity specification has been changed. (6.6 kW 6.4 kW)
4. Dimensions of unit have been changed. (W840 H640 D330 W800 H550 D285)
5. Communication system has been changed.
6. Power supply way has been changed (change to supply to outdoor unit).
7. Compressor has been changed. (SNV092FJYH SNB130FKCH)
8. Outdoor fan motor has been changed. (RA6V49 RC0J50-CF)
9. Evaporation temperature thermistor has been removed.
10. Gas pipe temperature thermistor has been removed.
11. Ambient temperature thermistor has been added.
MXZ-3A54VA - E1 MXZ-3A54VA - E2
MXZ-4A71VA - E1 MXZ-4A71VA - E2
1. Quick clean kit has been removed.
MXZ-2A30VA - E1
1. New model
MXZ-2A40VA - E1 MXZ-2A40VA - E2
1. Compressor has been changed. (SNB130FKCH KNB092FEDH)
2. Outdoor heat exchanger has been changed.
MXZ-2A52VA - E1 MXZ-2A52VA - E2
1. Compressor has been changed. (SNB130FKCH SNB130FKMH)
2. Inverter P.C. board has been changed.
MXZ-4A71VA - E2 MXZ-4A71VA - E3
1. Compressor has been changed. (SNB130FLDH1 SNB130FLEH1)
2. Electronic control P.C. board has been changed.
MXZ-4A80VA - E1 MXZ-4A80VA - E2
1. Ball valve has been changed to stop valve.
2. Gas pipe temperature thermistor has been removed.
3. Pre-heat control has been added.
4. Auto line correcting function has been added.
5. Noise filter P.C. board has been changed.
6. Electronic control P.C. board has been changed.
7. Weight has been changed. (70kg 67kg)
MXZ-5A100VA - E1
1. New model
MXZ-3A54VA - E3 MXZ-3A54VA - E4
1. Compressor has been changed. (SNB130FLEH1 SNB130FGBH1)
2. Electronic control P.C. board has been changed.
3. Gas pipe temperature thermistor has been removed.
4. Pre-heat control has been added.
5. Power board has been changed.
MXZ-4A71VA - E3 MXZ-4A71VA - E4
1. Compressor has been changed. (SNB130FLEH1 SNB130FGBH1)
2. Electronic control P.C. board has been changed.
3. Gas pipe temperature thermistor has been removed.
4. Pre-heat control has been added.
5. Power board has been changed.
MXZ-2A30VA - E1 MXZ-2A30VA - E2
1. Compressor has been changed. (KNB092FEDH KNB073FGDH)
2. Inverter P.C. board has been changed.
MXZ-3A54VA - E4 MXZ-3A54VA - E5
1. Electronic control P.C. board has been changed.
2. Noise filter P.C. board has been changed.
3. Ball valve has been changed to stop valve.
4. Sub panel has been added.
MXZ-4A71VA - E4 MXZ-4A71VA - E5
1. Electronic control P.C. board has been changed.
2. Noise filter P.C. board has been changed.
3. Ball valve has been changed to stop valve.
4. Sub panel has been added.
MXZ-3A54VA - E5 MXZ-3A54VA - E6
MXZ-4A71VA - E5 MXZ-4A71VA - E6
1. Electronic control P.C. board has been changed.
MXZ-3A54VA - E6 MXZ-3A54VA - E7
MXZ-4A71VA - E6 MXZ-4A71VA - E7
1. Electronic control P.C. board has been changed.
2. Compressor has been changed. (SNB130FGBH1 SNB130FGBH1T)
NOTE : The unit of pressure has been changed to MPa on the international system of units (SI unit system).
The conversion factor is: 1(MPa [Gauge]) =10.2(kgf/cm2 [Gauge])
3.5
R410A
Saturated liquid pressure
3.0 R22
2.5
2.0
1.5
1.0
NOTE : The unit of pressure has been changed to MPa on the
international system of units (SI unit system).
0.5
The conversion factor is: 1(MPa [Gauge]) =10.2(kgf/cm2 [Gauge])
0.0
-0.5
-30 -20 -10 0 10 20 30 40 50 60 (°C)
Outside diameter
Wall thickness Insulation material
mm
6.35 0.8 mm
9.52 0.8 mm Heat resisting foam plastic
12.7 0.8 mm Specific gravity 0.045 Thickness 8 mm
15.88 1.0 mm
Flaring work and flare nut
Flaring work for R410A pipe differs from that for R22 pipe.
For details of flaring work, refer to Installation manual “FLARING WORK”.
mm R410A R22
6.35 17 17
9.52 22 22
12.7 26 24
15.88 29 27
3. Refrigeration oil
Apply the special refrigeration oil (accessories: packed with indoor unit) to the flare and the union seat surfaces.
4. Air purge
• Do not discharge the refrigerant into the atmosphere.
Take care not to discharge refrigerant into the atmosphere during installation, reinstallation, or repairs to the refrigerant
circuit.
• Use the vacuum pump for air purging for the purpose of environmental protection.
5. Additional charge
For additional charging, charge the refrigerant from liquid phase of the gas cylinder.
If the refrigerant is charged from the gas phase, composition change may occur in the refrigerant inside the cylinder and the
outdoor unit. In this case, ability of the refrigeration cycle decreases or normal operation can be impossible. However,
charging the liquid refrigerant all at once may cause the compressor to be locked. Thus, charge the refrigerant slowly.
Union
Stop valve
Indoor unit
Liquid pipe
Gas pipe Outdoor unit
Refrigerant gas
cylinder
operating valve Service port
Gauge manifold
valve (for R410A)
Charge hose (for R410A)
Refrigerant (liquid)
Electronic scale for refrigerant charging
MXZ-2A30VA MXZ-3A54VA- E1 , E2 , E3 , E4
MXZ-2A40VA MXZ-4A71VA- E1 , E2 , E3 , E4
MXZ-2A52VA
Drain hose
Air outlet
Air outlet
Drain outlet
Drain outlet
MXZ-3A54VA- E5 , E6 , E7
MXZ-4A71VA- E5 , E6 , E7
Air inlet
(Back and side)
Air outlet
Drain outlet
ACCESSORIES
MXZ-3A54VA - E2 , E3 , E4 , E5 , E6 , E7
MXZ-2A30VA
MXZ-3A54VA - E1 MXZ-4A71VA - E2 , E3 , E4 , E5 , E6 , E7
MXZ-2A40VA
MXZ-4A71VA - E1 MXZ-4A80VA
MXZ-2A52VA
MXZ-5A100VA
Drain socket 1 1 1
Drain cap - 2 2
Quick Clean kit - 1 -
22+22 22+22
Indoor units
35+35+50
22+25 22+25 35+42+42
25+25 22+35 22+22+22+22
22+42 22+22+22+25
22+50 22+22+22+35
MXZ-2A40VA 22+60 22+22+22+42
25+25 22+22+22+50
22+22
combination
Indoor units
25+35 22+22+25+25
22+25
22+25
42+50 22+25+25+50
22+35
42+60 22+25+35+35
25+25
50+50 22+25+35+42
25+35
50+60 25+25+25+25
Indoor units combination
35+35
60+60 25+25+25+35
22+22+22 25+25+25+42
22+22+25 25+25+25+50
MXZ-3A54VA
22+22+35 25+25+35+35
22+22
22+22+42
22+25
22+22+50
22+35
22+22+60
22+42
22+25+25
22+50
22+25+35
25+25
22+25+42
25+35
Indoor units combination
22+25+50
25+42
22+25+60
25+50
22+35+35
35+35
22+35+42
35+42
22+35+50
35+50
22+35+60
42+42
22+42+42
42+50
22+42+50
50+50
22+42+60
22+22+22
22+50+50
22+22+25
25+25+25
22+22+35
25+25+35
22+22+42
25+25+42
22+22+50
25+25+50
22+25+25
25+25+60
22+25+35
25+35+35
22+25+42
25+35+42
22+25+50
25+35+50
22+35+35
25+35+60
22+35+42
25+42+42
25+25+25
25+42+50
25+25+35
25+50+50
25+25+42
35+35+35
25+25+50
35+35+42
25+35+35
10
42+60 35+42+42
42+71 35+42+50
50+50 35+42+60
50+60 35+50+50
50+71 35+50+60
60+60 22+22+22+22
60+71 22+22+22+25
22+22+22 22+22+22+35
22+22+25 22+22+22+42
22+22+35 22+22+22+50
22+22+42 22+22+22+60
22+22+50 22+22+22+71
22+22+60 22+22+25+25
22+22+71 22+22+25+35
22+25+25 22+22+25+42
22+25+35 22+22+25+50
22+25+42 22+22+25+60
22+25+50 22+22+25+71
22+25+60 22+22+35+35
22+25+71 22+22+35+42
22+35+35 22+22+35+50
22+35+42 22+22+35+60
22+35+50 22+22+42+42
22+35+60 22+22+42+50
22+35+71 22+22+50+50
22+42+42 22+25+25+25
22+42+50 22+25+25+35
22+42+60 22+25+25+42
22+42+71 22+25+25+50
22+50+50 22+25+25+60
22+50+60 22+25+35+35
22+50+71 22+25+35+42
25+25+25 22+25+35+50
25+25+35 22+25+35+60
11
12
combination
Indoor units
22+22+22+42+42 25+25+25+42+50
22+22+22+42+50 25+25+35+35+35
22+22+22+42+60 25+25+35+35+42
22+22+25+25+25 25+25+35+35+50
22+22+25+25+35 25+25+35+42+42
22+22+25+25+42
22+22+25+25+50
22+22+25+25+60
22+22+25+25+71
22+22+25+35+35
22+22+25+35+42
22+22+25+35+50
22+22+25+35+60
22+22+25+42+42
22+22+25+42+50
22+22+25+42+60
22+22+35+35+35
Indoor units combination
22+22+35+35+42
22+22+35+35+50
22+22+35+42+42
22+22+35+42+50
22+22+42+42+42
22+25+25+25+25
22+25+25+25+35
22+25+25+25+42
22+25+25+25+50
22+25+25+25+60
22+25+25+25+71
22+25+25+35+35
22+25+25+35+42
22+25+25+35+50
22+25+25+35+60
22+25+25+42+42
22+25+25+42+50
22+25+35+35+35
22+25+35+35+42
22+25+35+35+50
22+25+35+42+42
22+35+35+35+35
22+35+35+35+42
25+25+25+25+25
25+25+25+25+35
25+25+25+25+42
25+25+25+25+50
25+25+25+25+60
25+25+25+25+71
25+25+25+35+35
25+25+25+35+42
25+25+25+35+50
25+25+25+35+60
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
Max. 20
Connecting pipe length m Max. 15
Height difference (Indoor ~ Outdoor) m Refer to 9
Height difference (Indoor ~ Indoor) m Refer to 9
Function Cooling Heating
Capacity
Capacity [Rated (Min.-Max.) Hz] kW 3.0 (1.1 - 4.0) 4.0 (1.0 - 4.5)
Dehumidification /h — —
Outdoor air flow m3 /h 1,950 1,950
Breaker capacity A 10
Running current A 2.87 3.6
2 Electrical
Power factor % 90
Starting current A 3.60
Compressor motor current A 2.67 3.40
Fan motor current A 0.2
Coefficient of performance(C.O.P) 2 5.04 5.37
E1 KNB092FEDH
Model
Compressor
E2 KNB073FGDH
Output W 750
Winding U-V 1.70
Ω
resistance (at 20 °C) V-W 1.70 W-U 1.70
Model RC0J50-CF
motor
Fan
61
Max. 30
Connecting pipe length m Max. 20 Max. 20
Height difference (Indoor ~ Outdoor) m Refer to 9 Refer to 9
Height difference (Indoor ~ Indoor) m Refer to 9 Refer to 9
Function Cooling Heating Cooling Heating
Capacity
Capacity [Rated (Min.-Max.) Hz] kW 4.0 (1.1 - 4.5) 4.5 (1.0 - 5.0) 4.0 (1.1 - 4.5) 4.5 (1.0 - 5.0)
Dehumidification /h — — — —
Outdoor air flow m3 /h 1,860 1,860 1,950 1,950
Breaker capacity A 15 15
Running current A 4.78 4.32 4.78 4.32
2 Electrical
Power factor % 95 95
Starting current A 4.78 4.78
Compressor motor current A 4.58 4.12 4.58 4.12
Fan motor current A 0.2 0.2
Coefficient of performance(C.O.P) 2 3.83 4.76 3.83 4.76
Model SNB130FKCH KNB092FEDH
Compressor
NOTE: •Test conditions are based on ISO 5151. (Refrigerant piping length (one way): 5 m)
•Refer to 3 “INDOOR/OUTDOOR CORRESPONDENCE TABLE” for the combination.
1 Measured under rated operating frequency.
2 Electrical data is for only outdoor unit.
3 These specifications are when all indoor units are operating.
TEST CONDITIONS COOLING INDOOR Dry-bulb temperature 27.0°C Wet-bulb temperature 19.0°C
OUTDOOR Dry-bulb temperature 35.0°C Wet-bulb temperature 24.0°C
HEATING INDOOR Dry-bulb temperature 20.0°C
OUTDOOR Dry-bulb temperature 7.0°C Wet-bulb temperature 6.0°C
62
Capacity [Rated (Min.-Max.) Hz] kW 5.2 (1.1 - 6.0) 6.4 (1.0 - 7.2) 5.4 (2.9-6.8) 6.8 (2.6-9.0)
Dehumidification /h — — — —
Outdoor air flow m3 /h 1,860 1,860 2,525 2,470
Breaker capacity A 15 25
Running current A 6.75 7.64 5.69 6.39
2 Electrical
Power factor % 97 99
Starting current A 7.64 6.39
Compressor motor current A 6.55 7.44 5.49 6.19
Fan motor current A 0.2 0.2
Coefficient of performance(C.O.P) 2 3.46 3.75 4.17 4.67
E1 , E2 SNB130FLDH1
E1 SNB130FKCH
E3 SNB130FLEH1
Model
E4 , E5 , E6 SNB130FGBH1
E2 SNB130FKMH
Compressor
E7 SNB130FGBH1T
Output W 1,400 1,400
U-V 0.45
E1 , E2 , E3 V-W 0.45 W-U 0.45
Winding U-V 0.64
Ω
resistance(at 20 °C) V-W 0.64 W-U 0.64 U-V 0.98
E4 , E5 , E6 , E7
V-W 0.98 W-U 0.98
Model RC0J50-CF RC0J60-AA
motor
Fan
NOTE: •Test conditions are based on ISO 5151. (Refrigerant piping length (one way): 5 m)
•Refer to 3 “INDOOR/OUTDOOR CORRESPONDENCE TABLE” for the combination.
1 Measured under rated operating frequency.
2 Electrical data is for only outdoor unit.
3 These specifications are when all indoor units are operating.
TEST CONDITIONS COOLING INDOOR Dry-bulb temperature 27.0°C Wet-bulb temperature 19.0°C
OUTDOOR Dry-bulb temperature 35.0°C Wet-bulb temperature 24.0°C
HEATING INDOOR Dry-bulb temperature 20.0°C
OUTDOOR Dry-bulb temperature 7.0°C Wet-bulb temperature 6.0°C
63
Capacity [Rated (Min.-Max.) Hz] kW 7.1 (3.7-8.8) 8.6 (3.4-9.0) 8.0 (3.7-9.2) 9.4 (3.4-11.6)
Dehumidification /h — — — —
Outdoor air flow m3 /h 2,525 2,790 2,530 2,630
Breaker capacity A 25 25
Running current A 8.48 8.56 9.62 8.48
2 Electrical
Power factor % 99 99
Starting current A 8.56 9.62
Compressor motor current A 8.28 8.36 9.42 8.28
Fan motor current A 0.2 0.2
Coefficient of performance(C.O.P) 2 3.68 4.41 3.65 4.87
E1 , E2 SNB130FLDH1
E3 SNB130FLEH1
Model TNB220FMCH
E4 , E5 , E6 SNB130FGBH1
Compressor
E7 SNB130FGBH1T
Output W 2,000 2,100
U-V 0.45
E1 , E2 , E3
Winding V-W 0.45 W-U 0.45 U-V 1.41
Ω
resistance (at 20 °C) U-V 0.98 V-W 1.41 W-U 1.41
E4 , E5 , E6 , E7
V-W 0.98 W-U 0.98
Model RC0J60-AA PM8H60-UA
motor
Winding
Ω
resistance (at 20°C) WHT-RED 15.2 RED-BLK 15.2 WHT-RED 15.2 RED-BLK 15.2
Dimensions W x H x D mm 840 x 710 x 330 900 x 900 x 320
E1 70
Weight kg 58
E2 67
Sound level (High/Low) dB 48/45 50/48 46/44 48/46
Fan speed (High/Low) rpm 650/510 700/510 560/400 590/400
remarks
Special
NOTE: •Test conditions are based on ISO 5151. (Refrigerant piping length (one way): 5 m)
•Refer to 3 “INDOOR/OUTDOOR CORRESPONDENCE TABLE” for the combination.
1 Measured under rated operating frequency.
2 Electrical data is for only outdoor unit.
3 These specifications are when all indoor units are operating.
TEST CONDITIONS COOLING INDOOR Dry-bulb temperature 27.0°C Wet-bulb temperature 19.0°C
OUTDOOR Dry-bulb temperature 35.0°C Wet-bulb temperature 24.0°C
HEATING INDOOR Dry-bulb temperature 20.0°C
OUTDOOR Dry-bulb temperature 7.0°C Wet-bulb temperature 6.0°C
64
Power factor % 99
Starting current A 12.88
Compressor motor current A 12.68 12.25
Fan motor current A 0.2
Coefficient of performance(C.O.P) 2 3.41 4.23
Model TNB220FMCH
Compressor
Output W 2,700
Winding U-V 1.41
Ω
resistance(at 20 °C) V-W 1.41 W-U 1.41
Model PM8H60-UA
motor
Fan
NOTE: •Test conditions are based on ISO 5151. (Refrigerant piping length (one way): 5 m)
•Refer to 3 “INDOOR/OUTDOOR CORRESPONDENCE TABLE” for the combination.
1 Measured under rated operating frequency.
2 Electrical data is for only outdoor unit.
3 These specifications are when all indoor units are operating.
TEST CONDITIONS COOLING INDOOR Dry-bulb temperature 27.0°C Wet-bulb temperature 19.0°C
OUTDOOR Dry-bulb temperature 35.0°C Wet-bulb temperature 24.0°C
HEATING INDOOR Dry-bulb temperature 20.0°C
OUTDOOR Dry-bulb temperature 7.0°C Wet-bulb temperature 6.0°C
65
90 90
80 80
70 70
NC-70 NC-70
60 60
NC-60 NC-60
50 50
NC-50 NC-50
40 40
NC-40 NC-40
30 30
NC-30 NC-30
20 APPROXIMATE 20 APPROXIMATE
THRESHOLD OF THRESHOLD OF
HEARING FOR NC-20 HEARING FOR NC-20
CONTINUOUS CONTINUOUS
NOISE NOISE
10 10
63 125 250 500 1000 2000 4000 8000 63 125 250 500 1000 2000 4000 8000
90 90
OCTAVE BAND SOUND PRESSURE LEVEL, 0dB = 0.0002 MICRO BAR
80 80
70 70 NC-70
NC-70
60 60
NC-60 NC-60
50 50
NC-50 NC-50
40 40
NC-40 NC-40
30 30
NC-30 NC-30
20 APPROXIMATE 20 APPROXIMATE
THRESHOLD OF THRESHOLD OF
HEARING FOR NC-20 HEARING FOR NC-20
CONTINUOUS CONTINUOUS
NOISE NOISE
10 10
63 125 250 500 1000 2000 4000 8000 63 125 250 500 1000 2000 4000 8000
BAND CENTER FREQUENCIES, Hz BAND CENTER FREQUENCIES, Hz
66
90 90
OCTAVE BAND SOUND PRESSURE LEVEL, 0dB = 0.0002 MICRO BAR
70 70
NC-70 NC-70
60 60
NC-60 NC-60
50 50
NC-50 NC-50
40 40
NC-40 NC-40
30 30
NC-30 NC-30
20 APPROXIMATE 20 APPROXIMATE
THRESHOLD OF THRESHOLD OF
HEARING FOR NC-20 HEARING FOR NC-20
CONTINUOUS CONTINUOUS
NOISE NOISE
10 10
63 125 250 500 1000 2000 4000 8000 63 125 250 500 1000 2000 4000 8000
BAND CENTER FREQUENCIES, Hz BAND CENTER FREQUENCIES, Hz
90
1m
MICROPHONE
OCTAVE BAND SOUND PRESSURE LEVEL, 0dB = 0.0002 MICRO BAR
80
70
NC-70
60
Test conditions
NC-60
Cooling :Dry-bulb temperature 35°C Wet-bulb temperature 24°C
50 Heating :Dry-bulb temperature 7°C Wet-bulb temperature 6°C
NC-50
40
NC-40
30
NC-30
20 APPROXIMATE
THRESHOLD OF
HEARING FOR NC-20
CONTINUOUS
NOISE
10
63 125 250 500 1000 2000 4000 8000
67
MXZ-2A30VA Unit: mm
MXZ-2A40VA
MXZ-2A52VA
REQUIRED SPACE Basically open 100mm or more
without any obstruction in front
and on both sides of the unit.
400
ore
Drainage hole 42 or m
00mm
100 1
mm
o rm
44
ore
304 325
344.5
Air in 350
m mo
17.5
ore rm
or m ore
00mm
2
40
Air out
Open two sides of left,
right, or rear side.
handle
550
302.5 170.4
150 500
800 69
68
500
Open as a rule
63.2 233.1 288 More than 500 mm if
the back, both sides
17.7
38 and top are open
31.3
396
Air in
Air out
17.7
31
Indoor and
outdoor
connect wiring
840 30 39 x 27 hole 30 330 13
C unit connection
440
225
360
B unit connection
45
A unit connection
25
84
121 23.1
Liquid pipe
6.35(flared)1/4
69
17.7
31.3
Air in
16.8
20.3
(Bolt Pitch)
360.6
396
Air in
13.3
3- 33 Drain hole
17.7
Air out
27.1
240
66.3
710
Gas pipe 9.52(flared)3/8
C unit connection
440
225
B unit connection
360
45
A unit connection
84
1.Installation space
More than
More than
100
Note : Leave front and both sides
500
clearance fully.
More than
2.Service space
More than
200
More than
clearance fully.
500
350 350
500
70
500
Open as a rule
More than 500 mm if
63.2 233.1 288 the back, both sides
and top are open
17.7
38 More than 350 mm
31.3
Air in
360.6
16.8
396
Air in
Air out
17.7
31
Indoor and
outdoor
connect wiring
840 30 39 x 27 hole 30 330 13
Gas pipe
27.1 66.3 9.52(flared)3/8(B,C,D unit)
12.7(flared)1/2(A unit)
710
D unit connection
C unit connection
315
45
440
360
B unit connection
A unit connection
25
84
121 23.1
Liquid pipe
6.35(flared)1/4
71
17.7
31.3
Air in
16.8
20.3
(Bolt Pitch)
360.6
396
Air in
13.3
3- 33 Drain hole
17.7
Air out
27.1
240
Indoor and outdoor
connect wiring 66.3 Gas pipe
39 x 27 hole 9.52(flared)3/8(B,C,D unit)
12.7(flared)1/2(A unit)
D unit connection
710
C unit connection
315
440
B unit connection
360
45
A unit connection
84
299 23.1
1.Installation space
More than
More than
100
Note : Leave front and both sides
500
clearance fully.
2.Service space
More than
More than
200
More than
100
clearance fully.
350 350
500
72
(27)
(16)
Air in
35
Air in
355
387
74
(16)
40
Air out
Drainage holes 3- 33
2-12 x 36 Oval hole
Gas pipe
(Base bolt M10) 9.52(flared)3/8(B,C,D unit)
12.7(flared)1/2(A unit)
900 30 320 10
Indoor and
outdoor
connect wiring 88
26 x 45 hole
900
D unit connection
50
C unit connection
350
531.3
480.8
460
B unit connection
A unit connection
23
33
317 23
Liquid pipe
6.35(flared)1/4
1.Installation space
More than
More than
100
Note : Leave front and both sides
500
clearance fully.
More than
2.Service space
More than
200
More than
clearance fully.
500
350 350
500
73
16
Air in
27
35
74
11
(Bolt pitch)
355
387
Air in
24
3- 33 Drain hole
40
16
Air out
2-12 x 36 Oval hole Gas pipe
(Base bolt M10) 9.52(flared) 3/8 (B,C,D,E (MXZ-5A100VA) unit)
12.7(flared) 1/2 (A unit)
900 30 320 10
C unit connection
597
460
B unit connection
45
A
A unit connection
132
317 23
Liquid pipe
6.35(flared)1/4
1.Installation space
More than
More than
100
Note : Leave front and both sides
500
clearance fully.
More than
2.Service space
More than
200
More than
clearance fully.
500
350 350
500
74
L64
GRN/YLW 4 X64 3 BLK BLK
POWER SUPPLY PE TAB1 F61 CT61 DB61 U
BLK LD70 P LDU BLK BLK
~/N + + + CT761
L F64 LDV WHT 1 WHT U
230V 50Hz BLU V 2
C63A C63B C63C F801 R61 LDW RED 3 RED W
MC
BLK
T801 R62 IPM CT781 C
LD69
MXZ-2A30VA MXZ-2A40VA
N
LDE F901
BLU
DB65 9
L65 U 3 5
BLK 1 21S4 TR821
TO INDOOR POWER P.C. 2 P 1
IC801
UNIT No.B 230V~ S1 SSR61 CN912 V MF
GRN
BOARD 1
CONNECTING S2 N 2
CN934 CN933 W
R831 3
7
WIRING DIAGRAM
12-24V S3 TB3
CN937 IC932 CN932
BLK
6
CN938 CN936 CN935 INVERTER P.C. BOARD
BLU
1
ORN 2 CN602 7 CN661 CN663 CN662
3 1 2 3 4 5 6 1 2 1 2 CN791 CN792
MXZ-2A52VA
TO INDOOR BLK
S1 1 CN601 LED1 LED2 SW1
UNIT No.A 230V~ BLU 2 6 6
75
CONNECTING S2 3 INTERFACE DISPLAY
RED 4 LEV A LEV B
5 P.C. BOARD P.C. BOARD RT61 RT62 RT68 RT65 RT64
12-24V S3 TB2
SYMBOL NAME SYMBOL NAME SYMBOL NAME NOTES: 1.About the indoor side electric wiring
CT61,CT761,CT781 CURRENT TRANSFORMER MF OUTDOOR FAN MOTOR R61,R62,R831 CURRENT-DETECTING RESISTOR refer to the indoor unit electric wiring
C63A,C63B,C63C SMOOTHING CAPACITOR NF NOISE FILTER R64A,R64B RESISTOR diagram for servicing.
DB61,DB65 DIODE MODULE NR64 VARISTOR TB1,TB2,TB3 TERMINAL BLOCK 2.Use copper conductors only (for field wiring).
F61 FUSE (T20AL250V) RT61 DEFROST THERMISTOR TR821 SWITCHING POWER TRANSISTOR 3.Symbols below indicate.
F64,F801,F901 FUSE (T3.15AL250V) RT62 DISCHARGE TEMPERATURE THERMISTOR T801 SWITCHING TRANS :Terminal block :Connector
IC801 INTELLIGENT POWER DEVICE RT64 FIN TEMPERATURE THERMISTOR X64 RELAY
IPM,IC932 INTELLIGENT POWER MODULE RT65 AMBIENT TEMPERATURE THERMISTOR 21S4 R.V. COIL
L64,L65 REACTOR OUTDOOR HEAT EXCHANGER LEV A,LEV B EXPANSION VALVE
RT68
MC COMPRESSOR TEMPERATURE THERMISTOR SSR61 SOLENOID COIL RELAY
NOISE FILTER PFC POWER BOARD V
P.C. BOARD
X64
L
CT1 MC
3 BLK 3 4 R U
RED
TB1 U BLK W
GRN/YLW CB1 CB2 CB3
GROUND F64
PE TAB1
POWER BLK TAB4 WHT 1 2 YLW S
R64A R64B
MXZ-3A54VA -
CIRCUIT V
N
50Hz NR64
1 2
CN5
2 1
BREAKER
CN903
CT61 BLK
, E2
3 2 1
CN61 BLK CT2
1 2
CN902
RED
E3
RS1 RS3 W
CN2
F911 SSR61
7 6 5 4 3 2 1
CN901 RS2
BLK
BLU
LDE1 LDE2 1 2 CN912 1 2 3 4 5
CN4 BLK
BLK
1 2
CN3
TO INDOOR 1 2
UNIT No.C 12-24V S3 GRN GRN
BLU
BLU
CONNECTING S2 GRN
BLK
BLK
BLK
BLK
YLW 21S4
S1
BLK
BLK
BLK
RED
WHT
BLK
BLK
230V~
BLK
TB4
BLK
BLU
CN603
1 2 3
1 2 3 4 5 1 2 3 4 5 6 7 1 2 1 2 3 CN801
TO INDOOR ORN CN781 CN702 CN701
UNIT No.B 12-24V S3 F801 HC930
CONNECTING CN932
1 2 3
CN602
S2 T801 BLK
76
S1 RED WHT
230V~
BLU
RED
BLK
TB3 ELECTRONIC CONTROL P.C. BOARD
3 2 1
BLU R937A
CN601
TO INDOOR BLK YLW MF
1 2 3 4 5
(WHT) (RED) (BLU) R937B
UNIT No.A 12-24V S3 CN791 CN792 CN793 CN662 CN661 CN663 CN795 BLU
CONNECTING ORN
S2 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 1 2 3 4 5 6 PNK
230V~ S1 GRY
5 4 3 2 1
TB2
RED
BRN
BLU
ORN
YLW
WHT
RED
BRN
BLU
ORN
YLW
WHT
RED
BRN
BLU
ORN
YLW
WHT
GRY
GRY
GRY
GRY
GRY
GRY
GRY
GRY
BLK
BLK
GRY
GRY
GRY
GRY
RED
BRN
BLU
ORN
YLW
WHT
CN931
SYMBOL NAME SYMBOL NAME SYMBOL NAME NOTES: 1.About the indoor side electric wiring
CB1~3 SMOOTHING CAPACITOR MC COMPRESSOR RT64 FIN TEMPERATURE THERMISTOR refer to the indoor unit electric wiring
CT1, 2 CURRENT TRANSFORMER MF OUTDOOR FAN MOTOR RT65 AMBIENT TEMPERATURE THERMISTOR diagram for servicing.
CT61 CURRENT TRANSFORMER NR64 VARISTOR 2.Use copper conductors only (for field wiring).
FUSE (T2AL250V) RT68 OUTDOOR HEAT EXCHANGER
F64 N/F NOISE FILTER TEMPERATURE THERMISTOR 3.Symbols below indicate.
F801 FUSE (T3.15AL250V) PFC POWER FACTOR CONTROLLER SSR61 SOLENOID COIL RELAY :Terminal block :Connector
F911 FUSE (T1AL250V) R64A,B RESISTOR T801 TRANSFORMER
HC930 INTELLIGENT POWER MODULE R937A, B RESISTOR TB1~4 TERMINAL BLOCK
IPM INTELLIGENT POWER MODULE RS1~4 RESISTOR X64 RELAY
L REACTOR RT6A~C GAS PIPE TEMPERATURE THERMISTOR 21S4 R.V. COIL
LEV A~C EXPANSION VALVE RT61 DEFROST THERMISTOR
LEV E EXPANSION VALVE RT62 DISCHARGE TEMPERATURE THERMISTOR
MXZ-3A54VA -
E4
N F64 PTC64 1 2 U
CIRCUIT TAB2 TAB4
BREAKER
E5
1 BLK 1 3~
PTC65 2 BLK 2 MC W
E6
U NR64 CN902
TB4 BLU 3 1 BLK 1
YLW 2 BLK RS1 RS3 CT2
N/F
12-24V S3 BLK W RED
TO INDOOR BLU 1 CN2
S2 CN61 BLK RS2 RS4
UNIT No.C SSR61 CN3
BLK BLK
BLK
BLK
BLK
BLK
BLK
BLK
BLK
RED
WHT
GRN
21S4
TB3 ORN
S3 YLW 1 5 1 7 1 2 1 3
12-24V 3 CN801
TO INDOOR BLU CN603
S2 CN781 CN702 CN701
UNIT No.B BLK 1 F801
CONNECTING S1 HC930 CN932
230V~ T801 1
78
BLK
ORN 3 R937A WHT
CN602 RED
R937B 3 8
1
ELECTRONIC CONTROL P.C.BOARD 1 YLW
LED3 LED2 LED1 BLU
TB2 RED RED ORN
5 CN931 MS
12-24V S3 PNK
BLU BLU GRY 3~
TO INDOOR S2 CN601 (WHT) (RED) (BLU) 5
UNIT No.A CN791 CN792 CN793 CN661 CN663 CN795 MF
CONNECTING BLK BLK 1
230V~ S1 1 8 1 2
6 6 6 6
NOTES: 1. About the indoor side electric wiring refer to
the indoor unit electric wiring diagram for servicing. M M M RT61 RT68 M
2. Use copper conductors only (For field wiring).
3. Symbols below indicate. LEV A LEV B LEV C RT62 RT65 LEV E
:Terminal block :Connector
SYMBOL NAME SYMBOL NAME SYMBOL NAME SYMBOL NAME SYMBOL NAME
CB1~3 SMOOTHING CAPACITOR HC930 INTELLIGENT POWER MODULE MF FAN MOTOR RS1~4 RESISTOR SSR61 SOLENOID COIL RELAY
CT1,2 CURRENT TRANSFORMER IPM INTELLIGENT POWER MODULE NR64 VARISTOR RT61 DEFROST THERMISTOR T801 TRANSFORMER
CT61 CURRENT TRANSFORMER L REACTOR N/F NOISE FILTER RT62 DISCHARGE TEMP.THERMISTOR TB1~4 TERMINAL BLOCK
F64 FUSE(T2AL250V) LEV A~C EXPANSION VALVE PFC POWER FACTOR CONTROLLER RT64 FIN TEMP.THERMISTOR X64 RELAY
F65 FUSE(T6.3AL250V) LEV E EXPANSION VALVE PTC64,65 CIRCUIT PROTECTION RT65 AMBIENT TEMP.THERMISTOR 21S4 REVERSING VALVE SOLENOID COIL
F801 FUSE(T3.15AL250V) MC COMPRESSOR R937A,B RESISTOR RT68 OUTDOOR HEAT EXCHANGER TEMP.THERMISTOR
MXZ-3A54VA - E7
79
~/N WHT
N TAB2 BLK IPM
,
230V~ CIRCUIT V
N
50Hz NR64
1 2
CN5
2 1
BREAKER
CN903
E2
CT61 BLK
,
3 2 1
E3
1 2
CN902
RED
TO INDOOR
BLU
UNIT No.D 12-24V S3 RS1 RS3 W
CN2
CONNECTING F911 SSR61
S2
BLK
7 6 5 4 3 2 1
230V~ CN901 RS2 RS4
TB5
BLK
BLU
LDE2 1 2 CN912 1 2 3 4 5
LDE1 BLK
CN4
BLK
1 2
CN3
TO INDOOR BRN
UNIT No.C S3 GRN GRN
BLU
BLU
12-24V
CN604
1 2 3
CONNECTING S2 GRN
BLK
BLK
BLK
BLK
YLW 21S4
S1
BLK
BLK
BLK
RED
WHT
BLK
BLK
230V~
BLK
TB4
BLK
BLU
CN603
1 2 3
1 2 3 4 5 1 2 3 4 5 6 7 1 2 1 2 3 CN801
TO INDOOR ORN CN781 CN702 CN701
UNIT No.B S3 F801 HC930
12-24V
CONNECTING CN932
1 2 3
CN602
S2 T801 BLK
80
S1 RED WHT
230V~
BLK
BLU
TB3 ELECTRONIC CONTROL P.C. BOARD RED
3 2 1
BLU R937A
CN601
TO INDOOR BLK YLW MF
1 2 3 4 5
(WHT) (RED) (BLU) (GRN) R937B
UNIT No.A 12-24V S3 CN791 CN792 CN793 CN794 CN662 CN661 CN663 CN795 BLU
CONNECTING ORN
S2 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 1 2 3 4 5 6 PNK
230V~ S1 GRY
5 4 3 2 1
TB2
RED
BRN
BLU
ORN
YLW
WHT
RED
BRN
BLU
ORN
YLW
WHT
RED
BRN
BLU
ORN
YLW
WHT
RED
BRN
BLU
ORN
YLW
WHT
GRY
GRY
GRY
GRY
GRY
GRY
GRY
GRY
GRY
GRY
BLK
BLK
GRY
GRY
GRY
GRY
RED
BRN
BLU
ORN
YLW
WHT
CN931
SYMBOL NAME SYMBOL NAME SYMBOL NAME NOTES: 1.About the indoor side electric wiring
CB1~3 SMOOTHING CAPACITOR MC COMPRESSOR RT64 FIN TEMPERATURE THERMISTOR refer to the indoor unit electric wiring
CT1, 2 CURRENT TRANSFORMER MF OUTDOOR FAN MOTOR RT65 AMBIENT TEMPERATURE THERMISTOR diagram for servicing.
CT61 CURRENT TRANSFORMER NR64 VARISTOR 2.Use copper conductors only (for field wiring).
RT68 OUTDOOR HEAT EXCHANGER
F64 FUSE (T2AL250V) N/F NOISE FILTER TEMPERATURE THERMISTOR 3.Symbols below indicate.
F801 FUSE (T3.15AL250V) PFC POWER FACTOR CONTROLLER SSR61 SOLENOID COIL RELAY :Terminal block :Connector
F911 FUSE (T1AL250V) R64A,B RESISTOR T801 TRANSFORMER
HC930 INTELLIGENT POWER MODULE R937A, B RESISTOR TB1~5 TERMINAL BLOCK
IPM INTELLIGENT POWER MODULE RS1~4 RESISTOR X64 RELAY
L REACTOR RT6A~D GAS PIPE TEMPERATURE THERMISTOR 21S4 R.V. COIL
LEV A~D EXPANSION VALVE RT61 DEFROST THERMISTOR
LEV E EXPANSION VALVE RT62 DISCHARGE TEMPERATURE THERMISTOR
MXZ-4A71VA -
E4
BREAKER V WHT V MS
F65 N/F CN903 CN5
BLK 3~
E5
TB5 1 BLK 1
PTC65
,
BRN 2 2 MC W
12-24V S3 U NR64 CN902
BLU BLU 3 BLK
E6
TO INDOOR S2 1 BLK 1
UNIT No.D 2 RS1 RS3 CT2
N/F
CONNECTING BLK BLK W RED
230V~ S1 1 CN2
CN61 BLK RS2 RS4
SSR61 CN3
CN901 BLK CN4 2
LDE1 BLK
BLK
BLK
BLK
BLK
BLK
BLK
BLK
RED
WHT
GRN
TO INDOOR S2
UNIT No.C BLK
CONNECTING 21S4
230V~ S1
BRN 3 1 5 1 7 1 2 1 3
CN801
TB3 CN604 CN781 CN702 CN701
ORN 1
S3 F801
12-24V YLW 3 HC930 CN932
TO INDOOR BLU T801 1 BLK
UNIT No.B
S2 CN603 R937A WHT
82
CONNECTING BLK 1 RED
230V~ S1 ORN 3 R937B 3 8
CN602 ELECTRONIC CONTROL P.C.BOARD YLW
1 LED3 LED2 LED1 1 BLU
TB2 RED RED ORN
5 CN931 MS
12-24V S3 PNK
BLU BLU GRY 3~
TO INDOOR S2 CN601 (WHT) (RED) (BLU) (GRN) 5
UNIT No.A CN791 CN792 CN793 CN794 CN661 CN663 CN795 MF
CONNECTING BLK BLK 1
230V~ S1 1 8 1 2
6 6 6 6 6
NOTES: 1. About the indoor side electric wiring refer to
the indoor unit electric wiring diagram for servicing. M M M M RT61 RT68 M
2. Use copper conductors only (For field wiring).
3. Symbols below indicate. LEV A LEV B LEV C LEV D RT62 RT65 LEV E
: Terminal block : Connector
SYMBOL NAME SYMBOL NAME SYMBOL NAME SYMBOL NAME SYMBOL NAME
CB1~3 SMOOTHING CAPACITOR HC930 INTELLIGENT POWER MODULE MF FAN MOTOR RS1~4 RESISTOR SSR61 SOLENOID COIL RELAY
CT1,2 CURRENT TRANSFORMER IPM INTELLIGENT POWER MODULE NR64 VARISTOR RT61 DEFROST THERMISTOR T801 TRANSFORMER
CT61 CURRENT TRANSFORMER L REACTOR N/F NOISE FILTER RT62 DISCHARGE TEMP.THERMISTOR TB1~5 TERMINAL BLOCK
F64 FUSE(T2AL250V) LEV A~D EXPANSION VALVE PFC POWER FACTOR CONTROLLER RT64 FIN TEMP.THERMISTOR X64 RELAY
F65 FUSE(T6.3AL250V) LEV E EXPANSION VALVE PTC64,65 CIRCUIT PROTECTION RT65 AMBIENT TEMP.THERMISTOR 21S4 REVERSING VALVE SOLENOID COIL
F801 FUSE(T3.15AL250V) MC COMPRESSOR R937A,B RESISTOR RT68 OUTDOOR HEAT EXCHANGER TEMP.THERMISTOR
MXZ-4A71VA - E7
83
MXZ-2A30VA UNIT: mm
Compressor
Discharge
R.V. coil temperature
OFF Refrigerant flow in cooling thermistor RT62
ON Refrigerant flow in heating Muffler
Indoor unit
B 4-way valve
Stop valve
(with service port)
Indoor unit
A
Stop valve Outdoor heat
(with service port) exchanger
temperature
thermistor FAN-OUT
RT68
HEX-OUT
Ambient
temperature
Capillary tube thermistor
RT65
Indoor unit Defrost
A thermistor
Stop valve LEV A RT61
(with strainer #100)
Strainer
#100
Capillary tube
Indoor unit
B LEV B
Stop valve
(with strainer #100)
Refrigerant pipe diameter is different according to indoor unit to be connected. When using extension pipes, refer to the
tables below.
Indoor unit
Extension pipe diameter
class Pipe diameter
Liquid 6.35(1/4) Liquid 6.35(1/4) UNIT: mm (inch)
22/25
Gas 9.52(3/8) Gas 9.52(3/8) Outdoor unit union diameter
For
Liquid 6.35(1/4)
Indoor unit A
Gas 9.52(3/8)
Liquid 6.35(1/4)
Indoor unit B
Gas 9.52(3/8)
87
Compressor
Discharge
R.V. coil temperature
OFF Refrigerant flow in cooling thermistor RT62
ON Refrigerant flow in heating Muffler
Indoor unit
B 4-way valve
Stop valve
(with service port)
Indoor unit
A
Stop valve Outdoor heat
(with service port) exchanger
temperature
thermistor
RT68 FAN-OUT
HEX-OUT
Ambient
temperature
thermistor
RT65
Defrost
Capillary tube
thermistor
RT61
Indoor unit
A Capillary tube
Stop valve LEV A
(with strainer #100)
Strainer
#100 Distributor
Capillary tube
Indoor unit
B LEV B
Stop valve
(with strainer #100)
UNIT: mm (inch)
Outdoor unit union diameter
Indoor unit For
Extension pipe diameter
class Pipe diameter Liquid 6.35(1/4)
Indoor unit A
Liquid 6.35(1/4) Liquid 6.35(1/4) Gas 9.52(3/8)
22/25/35
Gas 9.52(3/8) Gas 9.52(3/8) Liquid 6.35(1/4)
Indoor unit B
Gas 9.52(3/8)
88
Compressor
Discharge
R.V. coil temperature
OFF Refrigerant flow in cooling thermistor RT62
ON Refrigerant flow in heating Muffler
Indoor unit
B 4-way valve
Stop valve
(with service port)
Indoor unit
A
Stop valve Outdoor heat
(with service port) exchanger
temperature
thermistor FAN-OUT
RT68
HEX-OUT
Ambient
temperature
Capillary tube thermistor
RT65
Indoor unit Defrost
A thermistor
Stop valve LEV A RT61
(with strainer #100)
Strainer
#100
Capillary tube
Indoor unit
B LEV B
Stop valve
(with strainer #100)
1,150 0 200
UNIT: mm (inch)
Outdoor unit union diameter
Indoor unit For
Extension pipe diameter
class Pipe diameter Liquid 6.35(1/4)
Indoor unit A
Liquid 6.35(1/4) Liquid 6.35(1/4) Gas 9.52(3/8)
22/25/35
Gas 9.52(3/8) Gas 9.52(3/8) Liquid 6.35(1/4)
Indoor unit B
Gas 9.52(3/8)
89
Indoor unit
B
Muffler
Indoor unit
A
Outdoor heat
exchanger
temperature FAN-OUT
thermistor
RT68
HEX-OUT
Ambient
temperature
thermistor
RT65
Defrost
Capillary tube
thermistor
RT61
Indoor unit
A Capillary tube
Strainer LEV A
#100 Ball valve
Capillary tube
Strainer Strainer
#100 LEV E #100 Distributor
Indoor unit
Power
B receiver
Strainer LEV B
#100
Capillary tube
Indoor unit
C LEV C
Strainer
#100
Refrigerant pipe diameter is different according to indoor unit to be connected. When using extension pipes, refer to the
tables below.
When diameter of refrigerant pipe is different from that of outdoor unit union, use optional Different-diameter pipe.
For further information on Different-diameter pipe, see 17-1.
UNIT: mm (inch)
90
Compressor
Discharge
R.V. coil temperature
OFF Refrigerant flow in cooling thermistor RT62
ON Refrigerant flow in heating Oil separator
Capillary tube
Indoor unit
B
Muffler
Indoor unit
A
Outdoor heat
exchanger
temperature FAN-OUT
thermistor
RT68
HEX-OUT
Ambient
temperature
thermistor
RT65
Defrost
Capillary tube
thermistor
RT61
Indoor unit
A Capillary tube
Strainer LEV A
#100
Capillary tube
Strainer Stop valve Strainer
#100 LEV E #100 Distributor
Indoor unit
Power
B receiver
Strainer LEV B
#100
Capillary tube
Indoor unit
C LEV C
Strainer
#100
Refrigerant pipe diameter is different according to indoor unit to be connected. When using extension pipes, refer to the
tables below.
When diameter of refrigerant pipe is different from that of outdoor unit union, use optional Different-diameter pipe.
For further information on Different-diameter pipe, see 17-1.
UNIT: mm (inch)
Indoor unit Outdoor unit union diameter
Extension pipe diameter
class Pipe diameter For
Liquid 6.35(1/4) Liquid 6.35(1/4)
22/25/35/42 Liquid 6.35(1/4)
Gas 9.52(3/8) Gas 9.52(3/8) Indoor unit A
Gas 9.52(3/8)
Liquid 6.35(1/4) Liquid 6.35(1/4)
50 Liquid 6.35(1/4)
Gas 12.7(1/2) Gas 12.7(1/2) Indoor unit B
Gas 9.52(3/8)
Liquid 6.35(1/4)
Indoor unit C
Gas 9.52(3/8)
91
Compressor
Discharge
R.V. coil temperature
OFF Refrigerant flow in cooling thermistor RT62
ON Refrigerant flow in heating Oil separator
Capillary tube
Indoor unit
Ball valve with
D
service port
4-way valve
Indoor unit
C
Indoor unit
Muffler
B
Indoor unit Outdoor heat
A exchanger
temperature
FAN-OUT
thermistor
RT68
HEX-OUT
Ambient
temperature
thermistor
RT65
Compressor
Discharge
R.V. coil temperature
OFF Refrigerant flow in cooling thermistor RT62
ON Refrigerant flow in heating Oil separator
Capillary tube
Indoor unit
D Stop valve with
service port 4-way valve
Indoor unit
C
Indoor unit
Muffler
B
Indoor unit Outdoor heat
A exchanger
temperature
FAN-OUT
thermistor
RT68
HEX-OUT
Ambient
temperature
thermistor
RT65
93
94
High-pressure Compressor
switch Discharge
R.V. coil temperature
OFF Refrigerant flow in cooling thermistor RT62
ON Refrigerant flow in heating Oil separator
Capillary tube
Indoor unit
D Stop valve
(with service port) 4-way valve
Indoor unit
C
Indoor unit
Muffler
B
Indoor unit
A
Outdoor Ambient
heat temperature
exchanger thermistor
Outdoor heat RT65
exchanger
temperature
thermistor
RT68
Capillary tube
Defrost
Indoor unit thermistor
RT61
A
Strainer LEV A
#100 Capillary tube
Indoor unit Stop valve Strainer Strainer
B #100 LEV F #100 Distributor
Strainer LEV B
#100 Power
receiver
Indoor unit
C Strainer LEV C
#100
Indoor unit
D LEV D
Strainer
#100
Indoor a
MAX REFRIGERANT PIPING LENGTH units
Piping length each indoor unit (a, b, c, d) 25m
Total piping length (a+b+c+d) 70m
Bending point for each unit 25 b Outdoor
unit 15m
Total bending point 70
It does not matter which unit is higher. 15m
ADDITIONAL REFRIGERANT CHARGE c
95
96
The standard specifications apply only to the operation of the air conditioner under normal conditions.
Since operating conditions vary according to the areas where these units are installed, the following information has been pro-
vided to clarify the operating characteristics of the air conditioner under the conditions indicated by the performance curve.
(1) GUARANTEED VOLTAGE
198~264 V 50 Hz
(2) AIR FLOW
Air flow should be set at MAX.
(3) MAIN READINGS
(1) Indoor intake air wet-bulb temperature :
(2) Indoor outlet air wet-bulb temperature :
(3) Outdoor intake air dry-bulb temperature :
(4) Total input:
°CWB
°CWB
°CDB
W
} Cooling
Indoor air wet/dry-bulb temperature difference on the left side of the following chart shows the difference between the
indoor intake air wet/dry-bulb temperature and the indoor outlet air wet/dry-bulb temperature for your reference at service.
How to measure the indoor air wet-bulb/dry-bulb temperature difference
1. Attach at least 2 sets of wet and dry-bulb thermometers to the indoor air intake as shown in the figure, and at least 2 sets
of wet and dry-bulb thermometers to the indoor air outlet. The thermometers must be attached to the position where air
speed is high.
2. Attach at least 2 sets of wet and dry-bulb thermometers to the outdoor air intake.
Cover the thermometers to prevent direct rays of the sun.
3. Check that the air filter is cleaned.
4. Open windows and doors of room.
5. Press the EMERGENCY OPERATION switch once (twice) to start the EMERGENCY COOL
(HEAT) MODE.
6. When system stabilizes after more than 15 minutes, measure temperature and take an average temperature.
7. 10 minutes later, measure temperature again and check that the temperature does not change.
97
25 class
35 class
Outdoor intake air Dry-bulb temperature (°C) Outdoor intake air Dry-bulb temperature (°C)
25 class
35 class
Outdoor intake air Wet-bulb temperature (°C) Outdoor intake air Wet-bulb temperature (°C)
MXZ-3A54VA
MXZ-4A71VA
8.5 9.3 10.6 9.5 13.1 13.7
Indoor air Wet-bulb temperature
25 class
35 class
42 class
50 class
60 class
Outdoor intake air Dry-bulb temperature (°C) Outdoor intake air Dry-bulb temperature (°C)
25 class
35 class
42 class
50 class
60 class
Outdoor intake air Wet-bulb temperature (°C) Outdoor intake air Wet-bulb temperature (°C)
98
25 class
35 class
42 class
50 class
60 class
71 class
Outdoor intake air Dry-bulb temperature (°C) Outdoor intake air Dry-bulb temperature (°C)
25 class
35 class
42 class
50 class
60 class
71 class
Outdoor intake air Wet-bulb temperature (°C) Outdoor intake air Wet-bulb temperature (°C)
MXZ-5A100VA
25 class
35 class
42 class
50 class
60 class
71 class
Outdoor intake air Dry-bulb temperature (°C) Outdoor intake air Dry-bulb temperature (°C)
)
23.4 22.2 23.9 24.9 29.0 29.4 32.4 °C) re (°C
re ( eratu
er atu lb temp
21.5 20.3 21.9 22.8 26.6 27.0 29.7 mp ry-bu
lb t
e air D
-bu take
19.5 18.5 19.9 20.7 24.1 24.5 27.0
Dry or in
ir Indo
kea
17.6 16.6 17.9 18.7 21.7 22.1 24.3 inta
oor
15.6 14.8 15.9 16.6 19.3 19.6 21.6 Ind
25 class
35 class
42 class
50 class
60 class
71 class
Outdoor intake air Wet-bulb temperature (°C) Outdoor intake air Wet-bulb temperature (°C)
99
100
101
102
103
104
105
106
107
108
10-4. OUTDOOR LOW PRESSURE AND OUTDOOR UNIT CURRENT (single operation)
NOTE: The unit of pressure has been changed to MPa on the international system of units (SI unit system).
The conversion factor is : 1 (MPa[Gauge]) = 10.2(kgf/cm2 [Gauge])
(1) COOL operation
Dry-bulb temperature ( ) Relative humidity (%)
Both indoor and outdoor unit are under the
same temperature/humidity condition. 20 50
Operation : TEST RUN OPERATION (Refer to 10-3.) 25 60
30 70
MXZ-2A30VA MXZ-2A40VA - E2
42Hz 42Hz
Outdoor low pressure
Outdoor low pressure
13 1.3 13 1.3
12 1.2 12 1.2
3 3
11 1.1 42Hz 11 1.1 42Hz
10 1.0 10 1.0
2 2
9 0.9 9 0.9
8 0.8 8 0.8
7 1 7 0.7 1
0.7
15 20 25 30 35 15 20 25 30 35 15 20 25 30 35 15 20 25 30 35
50 60 70 (%) 50 60 70 (%) 50 60 70 (%) 50 60 70 (%)
Ambient temperature ( ) Ambient temperature ( ) Ambient temperature ( ) Ambient temperature ( )
Ambient humidity (%) Ambient humidity (%) Ambient humidity (%) Ambient humidity (%)
MXZ-2A40VA- E2
35-class unit
(MPa[Gauge])
14
1.4 4
Outdoor unit current (A)
42Hz
Outdoor low pressure
13 1.3
12 1.2
3
11 1.1 42Hz
10 1.0
2
9 0.9
8 0.8
7 0.7 1
15 20 25 30 35 15 20 25 30 35
50 60 70 (%) 50 60 70 (%)
Ambient temperature ( ) Ambient temperature ( )
Ambient humidity (%) Ambient humidity (%)
109
13 1.3 13
1.2 12 1.2
12 3
3
30Hz
11 1.1 30Hz 11 1.1
10 1.0 10 1.0
2 2
9 9 0.9
0.9
8 8 0.8
0.8
7 7 0.7 1
0.7 1
15 20 25 30 35 15 20 25 30 35 15 20 25 30 35 15 20 25 30 35
(%) (%) 50 60 70 (%) 50 60 70 (%)
50 60 70 50 60 70
Ambient temperature ( ) Ambient temperature ( ) Ambient temperature ( ) Ambient temperature ( )
Ambient humidity (%) Ambient humidity (%) Ambient humidity (%) Ambient humidity (%)
35-class unit
(MPa[Gauge])
14
1.4 4
Outdoor unit current (A)
30Hz
Outdoor low pressure
13 1.3
12 1.2
3
30Hz
11 1.1
10 1.0
2
9 0.9
8 0.8
7 0.7 1
15 20 25 30 35 15 20 25 30 35
70 (%) 70 (%)
MXZ-3A54VA MXZ-4A71VA
22-class unit 25-class unit
(MPa[Gauge]) (MPa[Gauge])
12
1.2 5 1.2 5
12
Outdoor unit current (A)
40Hz 40Hz
Outdoor low pressure
11 1.1 11 1.1
4 4
10 1.0 40Hz 40Hz
10 1.0
9 0.9 3 9 0.9 3
8 0.8 8 0.8
2 2
7 0.7 7 0.7
6 0.6 1 6 0.6 1
15 20 25 30 35 15 20 25 30 35 15 20 25 30 35 15 20 25 30 35
50 60 70 (%) 50 60 70 (%) (%) (%)
50 60 70 50 60 70
Ambient temperature ( ) Ambient temperature ( ) Ambient temperature ( ) Ambient temperature ( )
Ambient humidity (%) Ambient humidity (%) Ambient humidity (%) Ambient humidity (%)
40Hz
Outdoor unit current (A)
40Hz
Outdoor low pressure
12 1.2 12 1.2
4 4
11 1.1 40Hz 40Hz
11 1.1
10 1.0 3 10 1.0 3
9 0.9 9 0.9
2 2
8 0.8 8 0.8
7 0.7 1 7 0.7 1
15 20 25 30 35 15 20 25 30 35 15 20 25 30 35 15 20 25 30 35
50 60 70 (%) 50 60 70 (%) (%) (%)
50 60 70
Ambient temperature ( ) Ambient temperature ( ) Ambient temperature ( ) Ambient temperature ( )
Ambient humidity (%) Ambient humidity (%) Ambient humidity (%) Ambient humidity (%)
110
12 1.2 13 1.3
4 4
11 1.1 40Hz 12 1.2 40Hz
10 1.0 3 11 1.1 3
9 0.9 10 1.0
2 2
8 0.8 9 0.9
7 0.7 1 8 0.8 1
15 20 25 30 35 15 20 25 30 35 15 20 25 30 35 15 20 25 30 35
50 60 70 (%) 50 60 70 (%) 50 60 70 (%) 50 60 70 (%)
MXZ-4A80VA
22-class unit 25-class unit
(MPa[Gauge]) (MPa[Gauge])
1.2 5 12
1.2 5
12
24Hz 24Hz
11 1.1 11 1.1
4 4
10 1.0 24Hz 10 1.0 24Hz
9 0.9 3 9 0.9 3
8 0.8 8 0.8
2 2
7 0.7 7 0.7
6 1 6 0.6 1
0.6
15 20 25 30 35 15 20 25 30 35 15 20 25 30 35 15 20 25 30 35
50 60 70 (%) 50 60 70 (%) 50 60 70 (%) 50 60 70 (%)
24Hz
Outdoor low pressure
Outdoor low pressure
12 1.2 12 1.2
4 4
24Hz 1.1 24Hz
11 1.1 11
10 1.0 3 10 1.0 3
9 0.9 9 0.9
2 2
8 0.8 8 0.8
7 1 7 0.7 1
0.7 15 20 25 30
15 20 25 30 35 15 20 25 30 35 35 15 20 25 30 35
50 60 70 (%) 50 60 70 (%) 50 60 70 (%) 50 60 70 (%)
24Hz
Outdoor unit current (A)
24Hz
Outdoor low pressure
Outdoor low pressure
12 1.2 13 1.3
4 4
11 1.1 24Hz 12 1.2 24Hz
10 1.0 3 11 1.1 3
9 0.9 10 1.0
2 2
8 0.8 9 0.9
7 1 8 0.8 1
0.7
15 20 25 30 35 15 20 25 30 35 15 20 25 30 35 15 20 25 30 35
50 60 70 (%) 50 60 70 (%) 50 60 70 (%) 50 60 70 (%)
111
11
13 1.3
4
4 24Hz
24Hz
10 1.0
12 1.2
9 0.9 3
11 1.1 3
8 0.8
10 1.0
2
2
7 0.7
9 0.9
6 0.6 1
8 0.8 1 15 20 25 30 35 15 20 25 30 35
15 20 25 30 35 15 20 25 30 35 70 (%) 70 (%)
(%) (%) 50 60 50 60
50 60 70 50 60 70
Ambient temperature ( ) Ambient temperature ( ) Ambient temperature ( ) Ambient temperature ( )
Ambient humidity (%) Ambient humidity (%) Ambient humidity (%) Ambient humidity (%)
MXZ-5A100VA
25-class unit 35-class unit
(MPa[Gauge]) (MPa[Gauge])
12
1.2 5 13
1.3 5
Outdoor unit current (A)
9 0.9 3 10 1.0 3
8 0.8 9 0.9
2 2
7 0.7 8 0.8
6 0.6 1 7 0.7 1
15 20 25 30 35 15 20 25 30 35 15 20 25 30 35 15 20 25 30 35
50 60 70 (%) 50 60 70 (%) 50 60 70 (%) 50 60 70 (%)
12 1.2 12 1.2
4 4
1.1 24Hz 24Hz
11 11 1.1
10 1.0 3 10 1.0 3
9 0.9 9 0.9
2 2
8 0.8 8 0.8
7 0.7 1 7 0.7 1
15 20 25 30 35 15 20 25 30 35 15 20 25 30 35 15 20 25 30 35
50 60 70 (%) 50 60 70 (%) 50 60 70 (%) 50 60 70 (%)
14
Outdoor unit current (A)
24Hz
Outdoor low pressure
24Hz
1.3
Outdoor low pressure
13
13 1.3
4
4
12 1.2 24Hz
12 1.2 24Hz
11 1.1 3
11 1.1 3
10 1.0
10 1.0
2
2
9 0.9
9 0.9
8 0.8 1 8 0.8 1
15 20 25 30 35 15 20 25 30 35
(%) (%) 15 20 25 30 35 15 20 25 30 35
50 60 70 50 60 70 (%) (%)
50 60 70 50 60 70
Ambient temperature ( ) Ambient temperature ( ) Ambient temperature ( ) Ambient temperature ( )
Ambient humidity (%) Ambient humidity (%) Ambient humidity (%) Ambient humidity (%)
112
Indoor Outdoor
Dry bulb temperature (°C) 20.0 2 7 15 20.0
Wet bulb temperature (°C) 14.5 1 6 12 14.5
Operation : TEST RUN OPERATION (Refer to 10-3.)
2 2 2
1 1 1
5 10 15 20 25 5 10 15 20 25 5 10 15 20 25
Ambient temperature ( ) Ambient temperature ( ) Ambient temperature ( )
MXZ-2A40VA- E1 MXZ-2A52VA
22-class unit 25-class unit 35-class unit
4 4 4
Outdoor unit current (A)
Outdoor unit current (A)
2 2 2
1 1 1
5 10 15 20 25 5 10 15 20 25 5 10 15 20 25
Ambient temperature ( ) Ambient temperature ( ) Ambient temperature ( )
MXZ-3A54VA MXZ-4A71VA
22-class unit 25-class unit 35-class unit 42-class unit
7 7 7 7
Outdoor unit current (A)
Outdoor unit current (A)
Outdoor unit current (A)
6 6 6 6
48Hz 48Hz
48Hz 48Hz
5 5 5 5
4 4 4 4
3 3 3 3
2 2 2 2
5 10 15 20 25 5 10 15 20 25 5 10 15 20 25 0 5 10 15 20 25
Ambient temperature ( ) Ambient temperature ( ) Ambient temperature ( ) Ambient temperature ( )
6 6
5 5
48Hz 48Hz
4 4
3 3
2 2
5 10 15 20 25 5 10 15 20 25
Ambient temperature ( ) Ambient temperature ( )
113
4 4 4 4
3 3 3 3
2 2 2 2
5 10 15 20 25 5 10 15 20 25 5 10 15 20 25 0 5 10 15 20 25
Ambient temperature ( ) Ambient temperature ( ) Ambient temperature ( ) Ambient temperature ( )
5 5 5
32Hz 32Hz 32Hz
4 4 4
3 3 3
2 2 2
5 10 15 20 25 5 10 15 20 25 5 10 15 20 25
Ambient temperature ( ) Ambient temperature ( ) Ambient temperature ( )
MXZ-5A100VA
22-class unit 25-class unit 35-class unit 42-class unit
7 7 7 7
Outdoor unit current (A)
6 6 6 6
32Hz 32Hz
32Hz 32Hz
5 5 5 5
4 4 4 4
3 3 3 3
2 2 2 2
5 10 15 20 25 5 10 15 20 25 5 10 15 20 25 0 5 10 15 20 25
Ambient temperature ( ) Ambient temperature ( ) Ambient temperature ( ) Ambient temperature ( )
6 6 6
5 5 5
32Hz 32Hz 32Hz
4 4 4
3 3 3
2 2 2
5 10 15 20 25 5 10 15 20 25 5 10 15 20 25
Ambient temperature ( ) Ambient temperature ( ) Ambient temperature ( )
114
115
ON ON
MXZ-4A80VA- E2
MXZ-5A100VA
12-2. LOWERING THE OPERATING NOISE OF THE OUTDOOR UNIT MXZ-4A80VA- E2
Description of the function: MXZ-5A100VA
With this function, you can lower the operating noise of the outdoor unit when the operation load is small,
for example, during nighttime in COOL mode. However, please note that the cooling and heating capacity
can also be lowered if this function is activated.
Initial setting is required to activate this function. Please explain about this function to your customers and
ask them whether they want to use it.
[How to lower the operating noise]
Turn OFF the power supply for the air conditioner before making the setting. SW1
ON
Set the 3rd Dip Switch of SW1 on the display P.C. board or the outdoor electronic
control P.C. board to ON to enable this function.
Turn ON the power supply for the air conditioner.
12-3. PRE-HEAT CONTROL <MXZ-2A, MXZ-3A54VA- E4 , E5 , E6 , E7 , MXZ-4A71VA- E4 , E5 , E6 , E7 ,
MXZ-4A80VA- E2 , MXZ-5A100VA>
If moisture gets into the refrigerant cycle, or when refrigerant is liquefied and collected in the compressor, it may interfere
the start-up of the compressor.
To improve start-up condition, the compressor is energized even while it is not operating.
This is to generate heat at the winding.
The compressor uses about 50 W when pre-heat control is turned ON.
Pre-heat control is ON at initial setting.
SW2 1 2 3 4 5 6
SW1
ON ON
JK
JK
1 2 3 4 5 6 1 2 3 4
MXZ-4A80VA- E2 MXZ-3A54VA- E4 , E5 , E6 , E7
MXZ-4A71VA- E4 , E5 , E6
SW2
SW1
, E7
MXZ-5A100VA
SW871
MXZ-2A
116
<MXZ-2A>
Improper wiring or piping can be automatically detected when one indoor unit is operated in COOL mode for 30 minutes.
When improper wiring or piping is detected, wiring lines are corrected (A to B/ B to A) with the software.
NOTE:
This function may not work due to the condition or environment of the unit, such as the following:
- gas leak, closed stop valve
- unit failure such as defective LEV
- indoor/outdoor temperature
<Correct line>
Refrigerant piping
Indoor/outdoor
connecting wire
A
B INDOOR UNIT A
<Incorrect wiring>
B INDOOR UNIT A
B INDOOR UNIT A
117
<MXZ-4A80VA- E2 , MXZ-5A100VA>
Improper wiring or piping can be automatically detected by pressing the piping/wiring correction switch (SW871).
When improper wiring or piping is detected, wiring lines are corrected.
This will be completed in about 10 to 15 min.
118
NOTE: Activate this function to confirm the correct wiring after replacing the electronic control P.C. board.
(Previous records are deleted when the electronic control P.C. board is replaced.)
The record cannot be shown if auto line correcting is not canceled (Refer to "How to activate this function").
12-5. INCREASING MAXIMUM COMPRESSOR OPERATIONAL FREQUENCY AND FAN SPEED OF THE
OUTDOOR UNIT
<MXZ-4A80VA- E2 , MXZ-5A100VA>
NOTE:
Compressor operational frequency may not be increased under primary current restriction or high pressure protection.
Compressor operational frequency will not be increased when 1 or 2 indoor units are operating.
This function doesn't work when the function which lowers the operating noise of the outdoor unit is activated.
Noise level of the outdoor unit will increase (You may need to explain this to your customers.)
Turn OFF the power supply for the air conditioner before making the setting.
Set the 3rd Dip Switch of SW2 on the outdoor electronic control P.C. board to ON to enable this function.
Turn ON the power supply for the air conditioner.
SW2
ON
1 2 3 4 5 6
If defrosting operation starts more than necessary, the defrost finish temperature and heat operation time can be changed.
The number of defrosting operation and defrosting time can be reduced with this function.
Initial setting Changed
Defrost finish temperature (°C) 10 5
Heat operation time (min.) 31 40
[How to change defrost finish temperature and heat operation time]
Turn OFF the power supply for the air conditioner before making the setting.
Set the 1st Dip Switch of SW2 on the outdoor electronic control P.C. board to ON to enable this function.
Turn ON the power supply for the air conditioner. SW2
ON
1 2 3 4 5 6
Refer to the service manual of indoor unit for how to recall the failure mode and the details of indoor unit failure mode.
The outdoor unit failure mode is indicated by the operation indicator lamp on the indoor unit and the LED of outdoor unit.
See "13-2.2. Outdoor unit failure mode table".
120
3-time flash Discharge temperature Lighting Once Thermistor shorts or opens during • Refer to 13-6. "Check
thermistor compressor running. of outdoor thermistors".
Defrost thermistor Lighting Once
Ambient temperature thermistor Lighting Twice
Fin temperature thermistor Lighting 3 times
P.C. board temperature Lighting 4 times • Replace the outdoor
thermistor electronic control
P.C. board.
Outdoor heat exchanger Lighting 9 times • Refer to 13-6. "Check
temperature thermistor of outdoor thermistors".
4-time flash Overcurrent Once Goes out 23 A (MXZ-2A30VA- E1 , MXZ-2A40VA, • Reconnect compressor
MXZ-2A52VA)/ 14 A (MXZ-2A30VA- E2 ) connector.
current flows into intelligent power • Refer to 13-6. "How
module. to check inverter/
compressor".
• Check the stop valve.
Compressor Twice The possibility of intercepting the • Check the connection of
Goes
overcurrent by the compressor lock is the compressor
out
high. connecting wire.
• Refer to 13-6. "How to
9 times Goes The compressor doesn't synchronize check inverter/
out with the operating power. compressor".
5-time flash Discharge temperature Lighting Lighting Discharge temperature exceeds 116°C • Check refrigerant circuit
during operation. and refrigerant amount.
Compressor can restart if discharge • Refer to 13-6. "Check
temperature thermistor reads 100°C or of LEV".
less 3 minutes later.
6-time flash High pressure Lighting Lighting The outdoor heat exchanger • Check refrigerant circuit
temperature exceeds 70°C during and refrigerant amount.
cooling or the indoor gas pipe • Check the stop valve.
temperature exceeds 70°C during
heating.
7-time flash Fin temperature 3 times Goes The fin temperature exceeds 90°C • Check around outdoor
out during operation. unit.
• Check outdoor unit air
P.C. board temperature 4 times Goes The P.C. board temperature exceeds passage.
out 78°C during operation. • Refer to 13-6. "Check
of outdoor fan motor".
8-time flash Outdoor fan motor Lighting Lighting Failure occurs continuously three • Refer to 13-6. "Check
times within 30 seconds after of outdoor fan motor".
the fan gets started.
NOTE: Blinking patterns of this mode differ from the ones of Troubleshooting check table (13-4).
121
15-time flash LEV for drain Lighting Lighting The indoor unit detects any • Refer to 13-6. "Check
abnormalities in the LEV for drain. of LEV".
• Check the drain pump of
the indoor unit.
NOTE: Blinking patterns of this mode differ from the ones of Troubleshooting check table (13-4).
122
8-time flash Outdoor fan motor Lighting Lighting Failure occurs continuously three • Refer to 13-6. "Check
times within 30 seconds after the of outdoor fan motor".
fan gets started.
NOTE: Blinking patterns of this mode differ from the ones of Troubleshooting check table (13-4).
123
Current sensor Lighting 7 times A short or open circuit is detected in • Replace the power
the current sensor during compressor board.
operating.
Current sensor protection stop is
continuously performed twice.
Zero cross detecting circuit 5 times Goes Zero cross signal cannot be detected • Check the connecting
out while the compressor is operating. wire among electronic
control P.C. board,
The protection stop of the zero cross noise filter P.C. board
detecting circuit is continuously and power board.
performed 10 times.
Converter 5 times Goes A failure is detected in the operation • Check the voltage of
out of the converter during operation. power supply.
• Replace the power board.
Bus-bar voltage 5 times Goes The bus-bar voltage exceeds 400 V or
(1) out falls to 200 V or below during
compressor operating.
Bus-bar voltage 6 times Goes The bus-bar voltage exceeds • Check the voltage of
(2) out 400 V (MXZ-3A54VA, MXZ-4A71VA)/ power supply.
Even if this protection stop is 430 V (MXZ-4A80VA, MXZ-5A100VA) • Replace the outdoor
performed continuously three or falls to 50V or below during electronic control
times, it does not mean the compressor operating. P.C. board.
abnormality in outdoor power
system.
15-time flash LEV for drain Lighting Lighting The indoor unit detects any • Refer to 13-6. "Check
abnormalities in the LEV for drain. of LEV".
• Check the drain pump of
the indoor unit.
NOTE: Blinking patterns of this mode differ from the ones of "Troubleshooting check table" (13-4).
Operation start
• Indoor unit • COOL or • When cooling, heat • When cooling, • When heating, • When cooling,
serial signal HEAT exchanger of dew drops in the room does not get room does not
error operation only non-operating indoor non-operating warm. cool.
Refer to 13-6. Refer to 13-6. unit frosts. indoor unit. Refer to 13-6. Refer to 13-6.
"How to "Check of •When heating, non- Check of "How to check of "How to check
check R.V. coil". operating indoor unit mispiping inverter/compressor". of inverter/
miswiring and gets warm. Check mispiping, compressor".
serial signal Refer to 13-6. shortage of capacity
error". "Check of LEV".
124
6 Lighting 7 times Nonvolatile memory data The nonvolatile memory data cannot be read properly. • Replace the outdoor electronic control P.C. board.
Bus-bar voltage The bus-bar voltage exceeds 430 V or falls to 50 V or below during • Replace the power board.
12 9 times Goes out protection compressor operating.
Failure occurs continuously three times within 30 seconds after the fan
13 13 times Goes out Outdoor fan motor • Refer to 13-6. "Check of outdoor fan motor".
gets started.
Current sensor A short or open circuit is detected in the current sensor during
14 8 times Goes out protection • Replace the power board.
compressor operating.
The discharge temperature exceeds 100°C during operation. • Check refrigerant circuit and refrigerant amount.
Discharge temperature
18 3 times Lighting • Refer to 13-6. "Check of LEV".
protection
• Refer to 13-6. "Check of outdoor thermistors".
125
Outdoor unit
21 operates 9 times Lighting Inverter check mode The unit is operated with emergency operation switch. -
normally.
ON
2.5-second OFF 2.5-second OFF
OFF
126
Fin temperature
• Refer to 13-6. "Check of outdoor thermistors".
thermistor
4 Lighting 4 times A short or open circuit is detected in the thermistor during operation.
P.C board temperature
• Replace the outdoor electronic control P.C. board.
thermistor
Ambient temperature
thermistor A short or open circuit is detected in the thermistor during operation.
6 Lighting 7 times Nonvolatile memory data The nonvolatile memory data cannot be read properly. • Replace the outdoor electronic control P.C. board.
7 Lighting 8 times Current sensor Current sensor protection stop is continuously performed twice. • Replace the power board.
Gas pipe temperature
thermistor A A short or open circuit is detected in the thermistor during cooling.
(A,B,C : MXZ-3A54VA- E1 , E2 , E3 , MXZ-4A71VA- E1 , E2 , E3
Gas pipe temperature
MXZ-4A80VA- E1 )
8 thermistor B • Refer to 13-6. "Check of outdoor thermistors".
Lighting 10 times (D : MXZ-4A71VA- E1 , E2 , E3 , MXZ-4A80VA- E1 )
Gas pipe temperature
thermistor C
Gas pipe temperature
thermistor D
Communication error Communication error occurs twice between the outdoor electronic control • Check the connecting wire between outdoor electronic control
9 Lighting 11 times
between P.C. boards P.C. board and power board for more than 10 seconds. P.C. board and power board.
Zero cross detecting The protection stop of the zero cross detecting circuit is continuously • Check the connecting wire among outdoor electronic control
10 Lighting 12 times
circuit performed 10 times. P.C. board, noise filter P.C. board and power board.
'Outdoor unit IPM protection Overcurrent is detected after 30 minutes of compressor start-up. • Reconnect compressor connector.
stops and
restarts 3 Twice Goes out • Refer to 13-6. "How to check inverter/compressor".
11
minutes • Check the stop valve.
Lock protection Overcurrent is detected within 30 minutes of compressor start-up
later' is • Check the power module (PAM module).
repeated.
Discharge temperature Discharge temperature exceeds 116°C during operation. Compressor can • Check the amount of gas and refrigerant circuit.
12 3 times Goes out protection restart if discharge temperature thermistor reads 100°C or less 3 minutes • Refer to 13-6. "Check of LEV".
later.
Fin temperature
The fin temperature exceeds 89°C during operation. •Check refrigerant circuit and refrigerant amount.
protection
13 4 times Goes out •Refer to 13-6. "Check of outdoor fan motor".
P.C. board temperature The P.C. board temperature exceeds 73°C (MXZ-3A54VA, MXZ-4A71VA)/
protection 87°C (MXZ-4A80VA, MXZ-5A100VA) during operation.
High-pressure High-pressure is detected with the high-pressure switch (HPS) during • Check the amount of gas and the refrigerant circuit.
protection operation. (MXZ-4A80VA, MXZ-5A100VA) • Check the stop valve.
14 5 times Goes out
The outdoor heat exchanger temperature exceeds 70°C during cooling
or indoor gas pipe temperature exceeds 70°C during heating.
Converter protection A failure is detected in the operation of the converter during operation.
15 8 times Goes out • Replace the power board.
Bus-bar voltage The bus-bar voltage exceeds 400 V or falls to 200 V or below during • Check the voltage of power supply.
protection (1) compressor operating. • Replace the power board or the outdoor electronic
16 control P.C. board.
9 times Goes out Bus-bar voltage The bus-bar voltage exceeds 400 V (MXZ-3A54VA, MXZ-4A71VA)/
protection (2) 430 V (MXZ-4A80VA, MXZ-5A100VA) or falls to 50 V or below during • Refer to 13-6. “Check of bus-bar voltage”.
compressor operating.
Failure occurs continuously three times within 30 seconds after the fan
17 13 times Goes out Outdoor fan motor • Refer to 13-6. "Check of outdoor fan motor".
gets started.
Current sensor A short or open circuit is detected in the current sensor during compressor
18 Lighting 8 times protection • Replace the power board.
operating.
Communication protection Communication error occurs between the outdoor electronic control P.C. • Check the connecting wire between outdoor electronic
19 Lighting 11 times board and power board for more than 10 seconds.
between P.C. boards control P.C. board and power board.
Zero cross detecting circuit • Check the connecting wire among outdoor electronic
20 Lighting 12 times Zero cross signal cannot be detected while the compressor is operating.
protection control P.C. board, noise filter P.C. board and power board.
127
Low discharge The frequency of the compressor is kept 80 Hz or more and the discharge
• Refer to 13-6. "Check of LEV".
24 4 times Lighting temperature protection temperature is kept under 50°C (COOL mode) /40°C (HEAT mode) for
• Check refrigerant circuit and refrigerant amount.
more than 40 minutes.
Outdoor unit
26 operates 9 times Lighting Inverter check mode The unit is operated with emergency operation switch. -
normally.
NOTE 1. The location of LED is illustrated at the right figure. Refer to 13-7.2. Outdoor electronic control P.C. board(Parts side)
2. LED is lighted during normal operation.
MXZ-3A54VA, MXZ-4A71VA, MXZ-4A80VA- E1
The flashing frequency shows the number of times the LED blinks after every 2.5-second OFF.
LED2 LED1
(Example) When the flashing frequency is “2”.
Lighting
0.5-second ON 0.5-second ON
MXZ-4A80VA- E2 , MXZ-5A100VA
LED1 LED2
ON
2.5-second OFF 2.5-second OFF Lighting
OFF
128
Ambient temperature Refer to 13-7. “Test point diagram and voltage”, 1. “Inverter P.C. board” , 2. “Outdoor
thermistor (RT65) electronic control P.C. board” or 5. “Outdoor Power board”, for the chart of thermistor.
Refer to 13-7. “Test point diagram and voltage”, 1. “Inverter P.C. board” or 2. “Outdoor
electronic control P.C. board”, for the chart of thermistor.
Compressor Measure the resistance between terminals using a tester.
W
RED (Winding temperature : -10°C ~ 40°C)
Normal (Each phase)
V U
2A30VA 2A40VA- E1 3A54VA - E1 , E2 , E3 3A54VA - , , ,
E4 E5 E6 E7 4A80VA
WHT BLK 2A40VA- E2 2A52VA 4A71VA - E1 , E2 , E3 4A71VA - , , ,
E4 E5 E6 E7 5A100VA
1.49 ~ 1.84 0.56 ~ 0.69 0.39 ~ 0.49 0.86 ~ 1.06 1.29 ~ 1.49
Outdoor fan motor Measure the resistance between lead wires using a tester.
(Part temperature : -10°C ~ 40°C)
Pressure Normal
High pressure switch (HPS)
MXZ-4A80/5A100 3.7 0.15 MPa Close
HPS
4.8 + 0.05
- 0.1 MPa Open
129
MXZ-2A30/2A40/2A52
Yes
Replace the inverter P.C. board.
MXZ-3A54/4A71/4A80/5A100
Yes
Replace the outdoor electronic control
P.C. board.
130
How to check mis-wiring and serial signal error (when outdoor unit does not work)
LED indication
for communication status
Communication status is indicated Turn OFF the power supply.
by the LED.
Unit status
Blinking: normal communication Is there rated voltage in No Check the power
Lighting: abnormal communication or the power supply? supply.
not connected
Pattern 1 and 2 is repeatedly displayed Yes
alternately. Each pattern is displayed for Turn ON the power supply.
15 seconds.
NOTE: "Lighting" in the table below does not
indicate abnormal communication. Is there rated voltage between No
outdoor terminal block S1 and Check the wiring.
S2?
MXZ-2A52VA Yes
Outdoor display P.C. board
Press EMERGENCY OPERATION switch once.
LED1 LED2
Is there voltage of 230V AC between pin1 and No 1. Turn OFF the power supply of indoor and outdoor unit, and
pin 2 at connector CN912? disconnect the connector CN933 or CN781.
2. 3 minutes after turning ON the power supply, start
Yes EMERGENCY OPERATION in HEAT mode.
Turn OFF the power supply of indoor and outdoor unit.
Yes Yes
Replace the 4-way valve. Replace the power P.C. board or
the noise filter P.C. board.
132
Check of LEV
Turn ON the power supply to the outdoor unit after checking LEV coil is mounted
to the LEV body securely.
133
Disconnect the terminal of the compressor. 3 minutes after turning ON the power supply, start
EMERGENCY OPERATION.
1 After the outdoor fan starts running, wait for 1 minute
or more before measuring the voltage.
Measure the voltage between each
The output voltage values have the tolerance of ± 20%.
lead wire leading to the compressor.
2 The output differs depending on the capacity or the
U (BLK) - V (WHT)
number of indoor units to be operated.
V (WHT) - W (RED) No
W (RED) - U (BLK)
Output voltage
COOL: 150V (48Hz) HEAT: 170V (64Hz)
Is voltage output? 1, 2
Yes
(MXZ-2A) Yes No
Is output balanced?
Yes (MXZ-3A/4A/5A)
Is the input voltage to the outdoor electronic No Replace the inverter P.C. board or
control P.C. board 370V or more? the power board.
Yes
Turn OFF the power supply of indoor and outdoor
unit, and measure the compressor winding
No
resistance between the compressor terminals.
Is there resistance between each terminal normal?
(Refer to 13-5.) Replace the
Yes compressor.
Reconnect the lead wire of compressor, and turn ON
the power supply to indoor and outdoor unit.
3 minutes later, start EMERGENCY OPERATION.
134
Does the unit operate 10 minutes or more without No Replace the inverter P.C. board,
showing thermistor abnormality? the outdoor electronic control P.C. board,
or the outdoor power board.
Yes
Normal
MXZ-2A30/2A40/2A52
Thermistor Symbol Connector, Pin No. Board
Defrost RT61 Between CN661 pin1 and pin2
Discharge temperature RT62 Between CN661 pin3 and pin4
Outdoor heat exchanger temperature RT68 Between CN661 pin5 and pin6 Inverter P.C. board
Fin temperature RT64 Between CN662 pin1 and pin2
Ambient temperature RT65 Between CN663 pin1 and pin2
MXZ-3A54/4A71/4A80/5A100
Thermistor Symbol Connector, Pin No. Board
Defrost RT61 Between CN661 pin1 and pin2
Discharge temperature RT62 Between CN661 pin3 and pin4
Outdoor heat exchanger temperature RT68 Between CN661 pin7 and pin8
Gas pipe temperature (Unit A) RT6A Between CN662 pin1 and pin2
Outdoor electronic control P.C. board
Gas pipe temperature (Unit B) RT6B Between CN662 pin3 and pin4
Gas pipe temperature (Unit C) RT6C Between CN662 pin5 and pin6
Gas pipe temperature (Unit D) RT6D Between CN662 pin7 and pin8
Ambient temperature RT65 Between CN663 pin1 and pin2
Fin temperature RT64 Between CN3 pin1 and pin2 Outdoor power board
Except MXZ-3A54VA- E4, E5 , E6 , E7 , MXZ-4A71VA- E4 , E5 , E6 ,E7 , MXZ-4A80VA- E2 and MXZ-5A100VA.
135
(Fixed to either 5V or 0V DC) No Does the voltage between each terminal become 5V DC and 0V DC
repeatedly?
Yes
No
Does the outdoor fan motor rotate smoothly?
Yes
Replace the outdoor fan motor. Replace the inverter P.C. board or the outdoor electronic control P.C. board.
136
Check of HPS
MXZ-4A80VA/5A100VA
1. Disconnect the connector CN681 in the electronic control P.C. board.
2. Check the resistance of HPS 1 minute after the outdoor unit power supply was turned OFF.
Normal
Replace the power board. Replace the outdoor elec- Replace the outdoor elec-
tronic control P.C. board. tronic control P.C. board.
JK,JGO
To
interface
P.C. board
(CN937)
Output to
drive
compressor
(LDW, LEV A
LDV, (CN791)
LDU) LEV B
(CN792)
(
12V
GND
Zero cross
X64
R.V. coil (CN933)
Primary current
(CN935)
To display P.C. board
thermistor/RT64 (CN662)
Fin temperature
5V DC
GND
5V
(CN931)
pulse wave
Output to drive
outdoor fan motor
(CN932)
Front side of unit ( To fan motor
180 90
60 30 300
40 20 200
20 10 100
0 0 0
-20 -10 0 10 20 30 40 0 10 20 30 40 50 60 70 80 90 100 110 120
0 10 20 30 40 50 60 70 80
138
Serial signal
12~24V DC
12~24V DC
12~24V DC
12~24V DC
Gas pipe temperature thermistor (RT6A, 6B, 6C, 6D)
230V AC
Room A
CN604
CN603
CN602
CN601
Input
Ambient temperature thermistor (RT65)
40
Temperature (°C)
30
20
10
Defrost thermistor (RT61)
CN795
( (
0
12V DC (–)
-10
pulse wave
CN791
-20
LEV E (+) (
100
90
80
70
60
50
40
30
20
10
Resistance (kΩ)
CN781
( (
12V DC
(–) pulse wave
(
(+)
12V R.V. coil (–) ( LEV Room
(+)
DC Rush current relay (–) A
GND (power board) CN792
CN702
15V
15V
( (
12V DC
(–) pulse wave
(–) LEV Room
(
Signal reception (
(+)
(From power board) GND B
5V DC pulse wave CN793
E1
(+)
( (
139
12V DC
CN701 (–)
MXZ-3A54VA MXZ-4A71VA MXZ-4A80VA -
pulse wave
Signal transmission (+)
(To power board)
5V DC pulse wave
(–) ( (
(+)
LEV Room
C
CN794
CN663 Ambient temperature
thermistor (RT65) ( (
(–)
(
12V DC
CN661 pulse wave
Outdoor heat exchanger
temperature thermistor (RT68) ( (+) LEV Room
(
D
2. Outdoor electronic control P.C. board
CN681 MXZ-4A80VA
Discharge temperature thermistor (RT62) ( (
High pressure switch
Defrost thermistor (RT61) (
CN662
100 110 120
(
Gas pipe D thermistor (RT6D)
CN931 GND
(
Discharge temperature thermistor (RT62)
60
20-90V AC
50
40
30
20
T3.15AL250V
10
FUSE
F801
LED 3
LED 1
LED 2
325~370
Bus-bar
voltage
CN801
SW1
V DC
Input
0
700
600
500
400
300
200
100
0
Resistance (kΩ)
MXZ-4A80VA - E2 MXZ-5A100VA Defrost thermistor (RT61)
Ambient temperature thermistor (RT65)
Outdoor heat exchanger temperature thermistor (RT68)
Discharge temperature thermistor (RT62) 100
700
90
Resistance (kΩ)
600 80
Resistance (kΩ)
500 70
400 60
300 50
200 40
30
100
20
0
0 10 20 30 40 50 60 70 80 90 100 110 120
10
thermistor (RT65)
5V DC pulse wave
(From power board)
pulse wave
5V DC
15V DC
5V DC
GND
GND
GND
(+)
(
(
LED 1
LED 2
LED 3
CN641
Serial signal Room E
F931 (MXZ-5A100VA)
FUSE 12~24V DC
T3.15AL250V
CN631
Serial signal Room D
12~24V DC
SW1 CN621
Serial signal Room C
SW2 12~24V DC
SW871
CN611
Serial signal Room B
12~24V DC
Bus-bar voltage
CN801 CN601
325~370 V DC 230V AC
Input Input
Serial signal
Room A
12~24V DC
F801
FUSE
T3.15AL250V
{( –
CN796
LEV F
12V DC
(
+ pulse wave
CN795
LEV Room E (MXZ-5A100VA)
CN794
LEV Room D
CN793
LEV Room C
CN792
LEV Room B
CN791
CN681 LEV Room A
High pressure switch
140
CN901
To electronic CN902 CN903
control To power To power
P.C. board board board
{
{ 230V AC
Input
CN912
R.V. coil
230V AC
{
230V AC
{ CN61
Output 230V AC
Output
MXZ-3A54VA - E5 , E6 , E7 MXZ-4A71VA - E5 , E6 , E7
CN901
To electronic
control CN903
P.C. board To power CN902
board To power
{
{
board
{
CN912 CN61
R.V. coil 230V AC
230V AC Output
230V AC
Output
F65
FUSE
T6.3AL250V
230V AC
F64 Input
FUSE
T2AL250V
141
{
{ CN61
230V AC
Output
230V AC
Output
F65
F64 FUSE
FUSE T6.3AL250V
T2AL250V
230V AC
Input
230V AC
Input
230V AC
Output
R.V.coil
(CN912)
230V AC
FUSE (F64) 12V R.V.coil Zero cross
T3.15AL250V
GND X64 Primary current
(
Resistance (kΩ)
140
120
100
80
60
40
20
0
0 10 20 30 40 50 60 70 80
Temperature (°C)
325-370V DC
Output Connect to the compressor
(Red) Voltage among phases: 5V to
(+) 1 180V
CN3
Fin temperature thermistor RT64
325-370V DC CN2
Output Connect to the controller board
(Red) (+)1-5(–): Signal transmission
(+) 1 (To electronic control P.C. board)
5V DC pulse wave
(+)2-5(–): Zero cross signal
(–) 3 3-4 : Not used
(White) (+)6-5(–): 15V
(+)7-5(–): 15V
CN3
Fin temperature thermistor RT64
CN5
Primary current detection
(Connect to the noise filter)
143
)
5V GND SW1
LED1 LED2
Serial signal
room A
144
(1) Slide the sleeve and check if there is a locking lever or not. (2) The terminal with this connector has the
locking mechanism.
Sleeve
Hooks
Screws of Service
the cabinet panel
145
146
(5) Detach the welded part of the suction and the discharge pipe Photo 6 Screws of the outdoor fan motor
connected with compressor.
(6) Remove the nuts of compressor legs.
(7) Remove the compressor.
(8) Detach the welded part of pipes connected with 4-way valve
(Photo 7).
Photo 7
147
Screws of the
cabinet
148
Screw of the
back panel
4 way valve
Screws of
LEV coil E the back panel
Expansion valve E
Suction pipe
welded part Screws of
the back panel
Screw of the
back panel
Discharge
pipe welded part
Photo 4
Compressor nuts
Screws of
the electrical
parts
Propeller
Sound
proof
felt
Propeller nut
Separator
149
Welded parts
150
151
Screw of the
back panel
4 way valve
Screws of
LEV coil E the back panel
Expansion valve E
Suction pipe
welded part Screws of
the back panel
Screw of the
Discharge back panel
pipe welded part
Photo 4
Compressor nuts
Screws of
the electrical
parts
Sound
Propeller nut proof
Propeller felt
Separator
152
R.V. coil
Welded parts
Expansion
LEV coils valves
153
Photo 3
LEV coil E
Expansion
valve E
Suction
pipe
welded
part
Discharge
pipe weld-
ed part
Terminal
154
Propeller
Sound
proof
felt
Separator
Propeller nut Compressor nuts
Welded parts
Expansion
valves
LEV coils
155
156
Photo 3
Discharge
pipe weld-
ed part
157
Propeller
Propeller nut
Sound
Separator proof felt
Welded parts
LEV coils
Expansion
valves
158
159
MXZ-2A40VA - E1 MXZ-2A52VA - E1
15-1. OUTDOOR UNIT STRUCTURAL PARTS AND FUNCTIONAL PARTS
17 16 15 14 10
18
19
13
1
11
12
3 4 5 6 7 8
2 9
160
MXZ-2A40VA - E1 MXZ-2A52VA - E1
161
MXZ-2A40VA - E1 MXZ-2A52VA - E1
15-2. OUTDOOR UNIT ELECTRICAL PARTS
13 12 11
10
1 2 3 4 5
6 7
Part numbers that are circled are not shown in the illustration.
Symbol Q'ty/unit
No. Part No. Part Name in Wiring Remarks
Diagram MXZ-2A40VA- E1 MXZ-2A52VA- E1
162
Symbol Q'ty/unit
No. Parts No. Parts Name in Wiring Remarks
MXZ-2A40VA- E1 MXZ-2A52VA- E1
Diagram
1 E02 838 704 DRAIN SOCKET 1 1
163
MXZ-3A54VA - E1 , E2
MXZ-4A71VA - E1 , E2
15-4. OUTDOOR UNIT STRUCTURAL PARTS AND FUNCTIONAL PARTS
23 22 21
24
20
19
18
17
16
15
12
2
3 11
4 5 6 7 8 9 10 13 14
164
MXZ-3A54VA - E1 , E2
MXZ-4A71VA - E1 , E2
15-4. OUTDOOR UNIT STRUCTURAL PARTS AND FUNCTIONAL PARTS
Part numbers that are circled are not shown in the illustration.
Symbol Q'ty/unit
No. Parts No. Parts Name in Wiring MXZ-3A54VA- MXZ-4A71VA- Remarks
Diagram E1 E2 E1 E2
165
MXZ-3A54VA - E1 , E2
MXZ-4A71VA - E1 , E2
15-5. OUTDOOR UNIT FUNCTIONAL PARTS AND ELECTRICAL PARTS
12 11 10
1 2 3 4 5 6 7
15-6. ACCESSORY 17
16
166
MXZ-3A54VA - E1 , E2
MXZ-4A71VA - E1 , E2
15-5. OUTDOOR UNIT FUNCTIONAL PARTS AND ELECTRICAL PARTS
Part numbers that are circled are not shown in the illustration.
Symbol Q'ty/unit
No. Parts No. Parts Name in Wiring MXZ-3A54VA- MXZ-4A71VA- Remarks
Diagram E1 E2 E1 E2
15-6. ACCESSORY
Symbol Q'ty/unit
No. Parts No. Parts Name in Wiring MXZ-3A54VA- MXZ-4A71VA- Remarks
Diagram E1 E2 E1 E2
167
25 24 23
22
21
19 18
20
2
14
15
17
16
1
5 13
2 6
12
11
7 8 9 10
168
169
12
11
10
1 2 3 4 5 6
15-9. ACCESSORY 16
170
Symbol Q'ty/unit
No. Parts No. Parts Name in Wiring Remarks
MXZ-4A80VA- E1
Diagram
1 M21 TK0 501 PROPELLER 1
2 M21 TK0 301 OUTDOOR FAN MOTOR MF 1 PM8H60-
3 T2W YH1 440 POWER BOARD 1 Including heat sink and RT64
4 T2W YH1 451 ELECTRONIC CONTROL P.C. BOARD 1
5 M21 TK0 337 REACTOR L 1 20A 600μH
6 T2W YH1 424 NOISE FILTER P.C. BOARD 1
7 T2W YH1 376 TERMINAL BLOCK TB2~5 4 Indoor unit connecting
8 T2W E64 376 TERMINAL BLOCK TB1 1 Power supply
9 T2W E70 307 GAS PIPE TEMPERATURE THERMISTOR RT6A,B,C,D 1
10 T2W TK0 398 R.V. COIL 21S4 1
DEFROST, DISCHARGE,
11 M21 G0H 308 THERMISTOR SET RT61,62,68 1 OUTDOOR HEAT EXCHANGER
12 M21 90V 309 AMBIENT TEMPERATURE THERMISTOR RT65 1
13 T2W YH1 381 FUSE F801 1 T3.15AL250V
14 T2W YH1 382 FUSE F911 1 T1AL250V
15 T2W E88 313 FUSE&VARISTOR SET F64,NR64 1 T2AL250V
15-9. ACCESSORY
Symbol Q'ty/unit
No. Parts No. Parts Name in Wiring Remarks
MXZ-4A80VA- E1
Diagram
DRAIN SOCKET 1
16 T2W E59 704 DRAIN SOCKET ASSEMBLY 1 DRAIN CAP 2
171
18
19
13
1
11
12
3 4 5 6 7
2 8 9
172
Symbol Q'ty/unit
RoHS
No. Part No. Part Name in Wiring MXZ-2A30VA- MXZ-2A40VA- MXZ-2A52VA- Remarks
Diagram E1 E2 E1 E2 E1 E2
173
1 2 3 4 5
6 7
Part numbers that are circled are not shown in the illustration.
Symbol Q'ty/unit
RoHS
No. Part No. Part Name in Wiring MXZ-2A30VA- MXZ-2A40VA- MXZ-2A52VA- Remarks
Diagram E1 E2 E1 E2 E1 E2
174
Symbol Q'ty/unit
RoHS
No. Parts No. Parts Name in Wiring MXZ-2A30VA- MXZ-2A40VA- MXZ-2A52VA- Remarks
Diagram E1 E2 E1 E2 E1 E2
175
MXZ-3A54VA - E1 , E2 , E3 , E4
MXZ-4A71VA - E1 , E2 , E3 , E4
16-4. OUTDOOR UNIT STRUCTURAL PARTS AND FUNCTIONAL PARTS
23 22 21
24
20
19
18
17
16
15
12
2
3 11
4 5 6 7 8 9 10 13 14
176
MXZ-3A54VA - E1 , E2 , E3 , E4
MXZ-4A71VA - E1 , E2 , E3 , E4
16-4. OUTDOOR UNIT STRUCTURAL PARTS AND FUNCTIONAL PARTS
Part numbers that are circled are not shown in the illustration.
Symbol Q'ty/unit
RoHS
177
MXZ-3A54VA - E1 , E2 , E3 , E4
MXZ-4A71VA - E1 , E2 , E3 , E4
16-5. OUTDOOR UNIT FUNCTIONAL PARTS AND ELECTRICAL PARTS
12 11 10
1 2 3 4 5 6 7
16-6. ACCESSORY 17
16
178
MXZ-3A54VA - E1 , E2 , E3 , E4
MXZ-4A71VA - E1 , E2 , E3 , E4
16-5. OUTDOOR UNIT FUNCTIONAL PARTS AND ELECTRICAL PARTS
Part numbers that are circled are not shown in the illustration.
Symbol Q'ty/unit
RoHS
16-6. ACCESSORY
Symbol Q'ty/unit
RoHS
179
MXZ-3A54VA - E5 , E6 , E7
MXZ-4A71VA - E5 , E6 , E7
16-7. OUTDOOR UNIT STRUCTURAL PARTS AND FUNCTIONAL PARTS
23 22 21 20
19
18
1 17
16
13
3
12
4 5 6 7 8 9 10 11 14 15
180
MXZ-3A54VA - E5 , E6 , E7
MXZ-4A71VA - E5 , E6 , E7
16-7. OUTDOOR UNIT STRUCTURAL PARTS AND FUNCTIONAL PARTS
Part numbers that are circled are not shown in the illustration.
Symbol Q'ty/unit
RoHS
181
MXZ-3A54VA - E5 , E6 , E7
MXZ-4A71VA - E5 , E6 , E7
16-8. OUTDOOR UNIT FUNCTIONAL PARTS AND ELECTRICAL PARTS
11 10 9
1 2 3 4 5 6 7
16
16-9. ACCESSORY 15
182
MXZ-3A54VA - E5 , E6 , E7
MXZ-4A71VA - E5 , E6 , E7
16-8. OUTDOOR UNIT FUNCTIONAL PARTS AND ELECTRICAL PARTS
Part numbers that are circled are not shown in the illustration.
Symbol Q'ty/unit
RoHS
16-9. ACCESSORY
Symbol Q'ty/unit
RoHS
183
25 24 23
22
21
19 18
20
2
14
15
17
16
1
5 13
2 6 12
11
7 8 9 10
184
Symbol Q'ty/unit
RoHS
185
12
11
10
1 2 3 4 5 6
16
16-12. ACCESSORY
186
Symbol Q'ty/unit
RoHS
16-12. ACCESSORY
Symbol Q'ty/unit
RoHS
187
22 21
23
24 20
19
17
18 16
15
14 2
1
2 5 13
6
7 8 9 10 11 12
188
Symbol Q'ty/unit
RoHS
189
11
10
1 2 3 4 5 6
16-15. ACCESSORY 15
190
16-15. ACCESSORY
Symbol Q'ty/unit
RoHS
191
13.7
5°
Z Z-Z
52.
15.7
MXZ-2A30
MXZ-2A40
48
79
10 x 48 (=480)
MXZ-4A80
450.8
MAC-855SG 51H-855
537.2
327
MXZ-5A100
103.1
42.6
Z 71.6
MAC-889SG
610.4 150
534 109.4
5- 6
29.2
760.8
832
29.2
6.4
386 5- 6
Punched hole
534
MAC-855SG
HEAD OFFICE: TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN