TSOP48..
Vishay Semiconductors
Description
The TSOP48.. - series are miniaturized receivers for
infrared remote control systems. PIN diode and
preamplifier are assembled on lead frame, the epoxy
package is designed as IR filter.
The demodulated output signal can directly be
decoded by a microprocessor. TSOP48.. is the stan- 1
dard IR remote control receiver series, supporting all 2
major transmission codes. 3 16672
Features
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
• Improved shielding against electrical field Parts Table
disturbance Part Carrier Frequency
• TTL and CMOS compatibility TSOP4830 30 kHz
• Output active low TSOP4833 33 kHz
• Low power consumption TSOP4836 36 kHz
TSOP4837 36.7 kHz
Special Features TSOP4838 38 kHz
• Improved immunity against ambient light TSOP4840 40 kHz
• Suitable burst length ≥ 10 cycles/burst TSOP4856 56 kHz
Block Diagram
Application Circuit
16833
3
VS
30 kΩ 16842
R1 = 100 Ω
1 Transmitter TSOPxxxx
with VS +VS
Band Demo- OUT TSALxxxx C1 =
Input AGC
Circuit
1.2
1.0
Output Pulse
E e min / E e – Rel. Responsivity
0.9 1.0
t po – Output Pulse Width ( ms )
0.8
0.7 Input Burst Duration 0.8
0.6
0.6
0.5
0.4 0.4
0.3
0.2 f = f0"5%
0.2 l = 950 nm,
Df ( 3dB ) = f0/10
0.1 optical test signal, fig.1
0.0
0.0
0.7 0.9 1.1 1.3
0.1 1.0 10.0 100.0 1000.010000.0
16925 f/f0 – Relative Frequency
16908 Ee – Irradiance ( mW/m2 )
Figure 2. Pulse Length and Sensitivity in Dark Ambient Figure 5. Frequency Dependence of Responsivity
1.5
Output Signal, ( see Fig.4 ) 94 8134 Ambient, l = 950 nm
VO
1.0
VOH 0.5
0.0
VOL
t 0.01 0.10 1.00 10.00 100.00
Ton Toff
16911 E – Ambient DC Irradiance (W/m2)
2.0 0.6
Ee min– Threshold Irradiance ( mW/m 2 )
1.0 0.3
f = 1 kHz
0.2
0.5
0.1
f = 100 Hz
0.0 0.0
0.1 1.0 10.0 100.0 1000.0 –30 –15 0 15 30 45 60 75 90
16912 DVsRMS – AC Voltage on DC Supply Voltage (mV) 16918 Tamb – Ambient Temperature ( qC )
Figure 7. Sensitivity vs. Supply Voltage Disturbances Figure 10. Sensitivity vs. Ambient Temperature
E e min– Threshold Irradiance ( mW/m 2 )
1.2
S ( l ) rel – Relative Spectral Sensitivity
2.0
f(E) = f0 1.0
1.6
0.8
1.2
0.6
0.8
0.4
0.4
0.2
0.0
0.0
0.0 0.4 0.8 1.2 1.6 2.0
750 850 950 1050 1150
94 8147 E – Field Strength of Disturbance ( kV/m )
16919 l – Wavelength ( nm )
Figure 8. Sensitivity vs. Electric Field Disturbances Figure 11. Relative Spectral Sensitivity vs. Wavelength
0° 10° 20°
0.8 30°
0.7
Max. Envelope Duty Cycle
0.6
40°
0.5 1.0
0.4 0.9 50°
0.3
0.8 60°
0.2 f = 38 kHz, Ee = 2 mW/m2 70°
0.7
0.1 80°
0.0
0 20 40 60 80 100 120 0.6 0.4 0.2 0 0.2 0.4 0.6
16913 Burst Length ( number of cycles / burst ) 96 12223p2 drel - Relative Transmission Distance
Figure 9. Max. Envelope Duty Cycle vs. Burstlength Figure 12. Directivity
IR Signal
The distinguishing mark between data signal and dis-
turbance signal are carrier frequency, burst length
and duty cycle.
The data signal should fulfill the following conditions: IR Signal from fluorescent
lamp with low modulation
• Carrier frequency should be close to center fre-
quency of the bandpass (e.g. 38 kHz).
0 5 10 15 20
• Burst length should be 10 cycles/burst or longer. 16920 Time ( ms )
• After each burst which is between 10 cycles and 70
cycles a gap time of at least 14 cycles is necessary. Figure 13. IR Signal from Fluorescent Lamp with low Modulation
Package Dimensions in mm
16003