Busca
Busca
1. Página Inicial
2. » Mapa de cabeamento AC - DTX CableAnalyzer
Base de conhecimento
Filtrar pesquisa por produto
Busca Limpar
Assure that Ethernet cabling supports services that use Power over Ethernet, before their deployment.
Test PoE cabling according to TIA standards even if a Midspan power supply is used.
Quickly solve cabling problems for a PoE service using a single tool.
A Midspan supply blocks the return of the DC signals a cable tester transmits to do the crucial Wire Map test. Without a Wire Map, cabling errors could go
undiscovered. These errors may delay the rollout of a PoE service and/or increase rollout cost. Cabling errors introduced after deployment may take down the
http://pt.flukenetworks.com/knowledge-base/dtx-cableanalyzer/ac-wire-map-dtx-cableanalyzer 1/9
02/02/2018 AC Wire Map Test for PoE Services - DTX CableAnalyzer | Fluke Networks
The new 1.41 (Current Version 2.78) release of software for the DTX CableAnalyzer includes a feature called “AC Wire Map.” This feature uses innovative
algorithms and technology to overcome the barrier introduced by Midspan supplies. The AC Wire Map test results provide evidence that the cable plant is or is
not ready for PoE services. LinkWare PC software captures the results of AC Wire Map tests to produce a comprehensive report on the health of a cable plant.
The DTX-NSM is not required to do "AC Wire Map".
The DTX Series Network Service Module (optional DTX-NSM) can then test Endspan or Midspan power supplies to determine if they deliver voltage in
compliance with the IEEE’s 802.3af PoE standard.
You cannot use AC Wire Map with either TIA Cat 6, 6A or Class E, EA limits. The return loss will always fail. This is not the fault of the DTX CableAnalyzer.
These devices are rated for 1000BASE-T at most, and hence will have more return loss in them than that allowed for either Cat 6, 6A or Class E, EA.
http://pt.flukenetworks.com/knowledge-base/dtx-cableanalyzer/ac-wire-map-dtx-cableanalyzer 2/9
02/02/2018 AC Wire Map Test for PoE Services - DTX CableAnalyzer | Fluke Networks
http://pt.flukenetworks.com/knowledge-base/dtx-cableanalyzer/ac-wire-map-dtx-cableanalyzer 3/9
02/02/2018 AC Wire Map Test for PoE Services - DTX CableAnalyzer | Fluke Networks
http://pt.flukenetworks.com/knowledge-base/dtx-cableanalyzer/ac-wire-map-dtx-cableanalyzer 4/9
02/02/2018 AC Wire Map Test for PoE Services - DTX CableAnalyzer | Fluke Networks
AC wire map results are similar to the wire map results you normally see.
http://pt.flukenetworks.com/knowledge-base/dtx-cableanalyzer/ac-wire-map-dtx-cableanalyzer 5/9
02/02/2018 AC Wire Map Test for PoE Services - DTX CableAnalyzer | Fluke Networks
In some cases, the fault information provided by AC wire maps is less specific. For example, if a wire is shorted to a wire in another pair, the AC wire map
shows all four wires shorted.
http://pt.flukenetworks.com/knowledge-base/dtx-cableanalyzer/ac-wire-map-dtx-cableanalyzer 6/9
02/02/2018 AC Wire Map Test for PoE Services - DTX CableAnalyzer | Fluke Networks
This occurs because the AC electrical characteristics of some faults limit the measurements available from the fault.
When the tester detects multiple wire map faults, it may not display the wire map screen, but may show a diagnostics screen instead.
http://pt.flukenetworks.com/knowledge-base/dtx-cableanalyzer/ac-wire-map-dtx-cableanalyzer 7/9
02/02/2018 AC Wire Map Test for PoE Services - DTX CableAnalyzer | Fluke Networks
http://pt.flukenetworks.com/knowledge-base/dtx-cableanalyzer/ac-wire-map-dtx-cableanalyzer 8/9
02/02/2018 AC Wire Map Test for PoE Services - DTX CableAnalyzer | Fluke Networks
Manuais
http://pt.flukenetworks.com/knowledge-base/dtx-cableanalyzer/ac-wire-map-dtx-cableanalyzer 9/9