Anda di halaman 1dari 12

Frame Assembly and Installation Guide

Frame Assembly and Installation Guide


for Andersen® 400 Series Frenchwood®, 200 Series Narroline®, and
200 Series Perma-Shield® Gliding Patio Doors

Congratulations! You have just purchased one of the many fine Andersen® products. Proper assembly, installation
and maintenance are essential if the benefits of your Andersen product are to be fully attained. Therefore, please read
and follow this instruction guide completely. If your abilities do not match this procedure’s requirements, contact an
experienced contractor. You may direct any questions about this or other products to your local Andersen dealer, found
in the Yellow Pages under “Windows” or call Andersen WindowCare® service center at 1-888-888-7020 Monday through
Friday, 7 a.m. to 7 p.m. Central Time and Saturday, 8 a.m. to 4 p.m. Central Time. Thank you for choosing Andersen.

Every assembly and installation is different (windloads, structural support, etc.). Andersen strongly recommends
consultation with an Andersen supplier or an experienced contractor, architect, or structural engineer prior to the
assembly and installation of any Andersen product. For installation methods not covered in this guide, (i.e. through
jamb) please visit the Architect Detail File on the web (www.andersenwindows.com). Andersen has no responsibility in
regard to the post-manufactured assembly and installation of Andersen products.

1
Use caution when working at elevated Follow manufacturer’s Windows and doors can be heavy.
heights and around unit openings. Follow instructions for safe operation Use safe lifting techniques and a
manufacturer’s instructions for safe use of of hand/power tools. Always reasonable number of people with
ladder and/or scaffolding. Failure to do so wear safety glasses. Failure to enough strength to lift, carry and
may result in injury or death. do so may result in injury and/ install window and door products
or product damage. to avoid injury and/or product
damage.

Unless specifically ordered, Andersen windows and doors are not equipped with safety glass, and if broken, could
fragment causing injury. Many laws and building codes require safety glass in locations adjacent to or near doors.
Andersen windows are available with safety glass that may reduce the likelihood of injury when broken. Information
on safety glass is available from your local Andersen dealer.

• Andersen® Head Flashing and Installation Flanges DO NOT take the place of standard window and door flashing. Unit
must be properly flashed and sealed with silicone for protection against water and air infiltration. Use non-reflective
flashings. Highly reflective flashing tapes can raise the surface temperature of the vinyl to the point where vinyl
deformation and product damage may occur.
• Do not apply any type of film to glass. Thermal stress conditions resulting in glass damage could occur.
• Use of movable insulating materials such as window coverings, shutters, and other shading devices may damage
glass and/or vinyl. In addition, excessive condensation may result causing deterioration of windows and doors.

“Andersen” and “Andersen WindowCare” are registered trademarks of Andersen Corporation. All other marks where denoted are marks of Andersen Corporation.
©2002-2007 Andersen Corporation. All rights reserved. Instruction Guide 0005310 BB Revised 08/24/07

1
Frame Assembly and Installation Guide

Masonry/Concrete Installations Only


• Acid solutions used to wash masonry/concrete will damage glass, fasteners, hardware, and metal flashing.
Follow the acid solution manufacturer's instructions carefully. Protect and/or cover Andersen® products
during cleaning process to prevent acid contact. If acid does come in contact with unit, immediately wash all
surfaces with clean water.
• DO NOT install unit directly on masonry/concrete surface. Place a full length barrier (i.e. treated wood, tar paper,
ice/water membrane) between unit sill and masonry/concrete surface. Failure to use barrier and sealing it to
masonry/concrete surface and unit sill may result in product and/or property damage. Entire barrier must be
sealed to masonry/concrete surface to help prevent water infiltration. Barrier thickness must not exceed 1/4”.

• Frames are manufactured for left or right hand operation (L or R) or stationary sidelights. Door operation is as
viewed from the outside.
• Provide a large work area when assembling patio door frame. Cover work area with cardboard to protect
frame parts.
• Following frame assembly, attach screw pack envelope, with remaining screws, to frame for use when
installing unit frame and door panels on the job site.

Parts Included (All Doors) Additional Parts Tools & Supplies


(1) Installation Guide Stationary Sidelight • Safety Glasses
(1) Head Installation Flange (2) Side Stops • Carpenters Level
(2) Side Installation Flanges • Phillips Screwdriver
(1) Sill • Caulk Gun
2-Panel Door
(1) Head Jamb • Silicone Sealant
(1) Stationary Panel
(1) Left Side Jamb • Clamps
Interlock Weatherstrip
(1) Right Side Jamb • Shims
(1) Operating Panel
(1) Head Flashing • Small Wood Block
Interlock Weatherstrip
(1) Silicone Sealant • Hammer
(1) Head Bracket
(1) Screw Pack • Drill
• 1/16" Drill Bit
4-Panel Door
(2) Stationary Panel Optional Accessories
Interlock Weatherstrip • Corrosion Resistant Screw Kit
(2) Operating Panel • Insect Screen
Interlock Weatherstrip • Sill Support
(2) Head Bracket • Exterior Keyed Lock
• Auxiliary Sill Lock
Additional Parts Required • Interior/Exterior Grilles
• Door Hardware • Oak Threshold

2
Frame Assembly and Installation Guide
Component Identification
Head Installation
Head Flange
Flashing
Side
Head Installation *Stationary Panel Interlock Weatherstrip
Jamb Flange

PLUM - LEVEL - SHIM


PLUM - LEVEL - SHIM

*Operating Panel Interlock Weatherstrip

PLUM - LEVEL - SHIM


Exterior View

Clear Silicone Sealant

PLUM - LE
PLUM - LEVEL - SHIM

Sill (Perma-Shield® (2902502)


Gliding Door) Side Jamb

Sill (DP Upgrade Perma-Shield® Gliding Door,


Narroline® Gliding Door,
Frenchwood® Gliding Door)
PLUM - LEVEL - SHIM

Side Jamb
Side
Installation
Flange
Stationary
Panel Hole Plug* Panel Bracket* Insect Screen Latch Parting Stop Bracket Side Stop
Forest Green
(25735490)

Sandtone
(2573551)

(0912717)

(2573692)
(2653804)

(2579551)

(0924602)

(1267822)
White

Stone

White
White

Gray
Gray

Gliding Door Product


Perma-Shield®
Standard 1 1
8’ DP Upgrade (2-Panel) 1 1
Sidelight 2

Narroline® or

Frenchwood® (2-Panel)
Standard 2 1 1
Impact Resistant (FW only) 1
8’ Wide 2 1 1
8’ High 2 1 1
Sidelight 2
Narroline® or
Factory Applied
Frenchwood (4-Panel)
®

10’ and 12’ Wide 4 2 1 DP Upgrade Only


16’ Wide 4 2 1 DP Upgrade Only
10’ and 12’ Wide x 8’ High 4 2 1 DP Upgrade Only
16’ Wide x 8’ High 4 2 1 Standard and
DP Upgrade
Sidelight 2

* Identifies parts for panel installation. Frame and panels are packaged separately. Please keep remaining parts for panel installation.

3
Frame Assembly and Installation Guide

Metal fasteners and components may corrode when exposed to preservative-treated and fire-retardant treated
lumber. Obtain and use the appropriate metal fasteners and hardware as called out by the installation guide to
fasten unit to any rough opening made from preservative-treated and fire-retardant treated lumber. Failure to use
the appropriate materials for the installation may cause a failure resulting in injury, property or product damage.

Screw Identification

* * * *

#7 x 5/8” #7 x 5/8” #8 x 3/4” #8 x 1” #8 x 1” #8 x 1-1/2” #10 x 2-1/2” #10 x 2-1/2”

Gray (2500704) for Narroline® and Frenchwood® Door


Sandtone (0904112), Forest Green (1269110)

Gray (2500703) for Perma-Shield® Door

White (1973114), Terratone® (2641211),


White (2500706), Terratone® (2653864)

White (1973111), Terratone® (2653861)


White (2500702), Terratone® (2653862)

Sandtone (0904110), Gold (2500701)


White (1973109), Gray (2641210)

Sandtone (0904109)
Stainless (1973107)

Stainless (1973110)

Silver (1973113)

Gray (0912718)
Gliding Door Product

Perma-Shield®
Standard 18* 5* 4* 1 5* 9 14
8’ DP Upgrade (2-Panel) 22* 5* 6* 1 5* 11 14
Sidelight DP 12* 4* 10 14
Narroline® or
Frenchwood (2-Panel)
®

Standard 18* 5* 4* 1 7* 9 14
Impact Resistant (FW only) 18* 10* 4* 1 7* 9 14 3
8’ Wide 18* 5* 6* 1 10* 11 14
8’ High 22* 5* 6* 1 10* 13 14
Sidelight 12* 4* 10 14
Imp. Res. Sidelight (FW only) 12* 4* 12 14
Narroline® or
Frenchwood (4-Panel)
®

10’ and 12’ Wide 36* 1 10 8* 14* 13 14


16’ Wide 36* 1 10 12* 20* 17 14
10’ and 12’ Wide x 8’ High 44* 1 10 12* 20* 15 14
16’ Wide x 8’ High 44* 1 10 12* 20* 19 14
* Identifies screw for panel installation. Frame and panels are packaged separately. Please keep remaining screws for panel installation.

4
Frame Assembly and Installation Guide
1. Attach Side Jambs to Sill
• Position Sill and Side Jambs exterior up. Sill

Silicone Sealant

Silicone Sealant must be applied to ends of Sill


and Side Jambs to help prevent water infiltration.
Screw Guide
• Apply a 1/8" bead of Silicone Sealant (provided in Perma-Shield® Gliding Patio Door and Sidelights
frame package) to bottom ends of Side Jambs. (Top
ends have a beveled cut.)
Sill
• Apply a 1/8" bead of Silicone Sealant to ends of Sill Sill Filler
and position against Side Jambs.

Silicone
Sealant
• Screw fastening sequence must be followed when
attaching Side Jambs to Sill. Failure to do so may
result in incorrect fit of frame parts.
Frenchwood® Gliding Patio Door,
• Make sure insect screen track on Sill is inserted 8’ Perma-Shield® Gliding Patio Door,
into slot on the bottom of Side Jamb. Failure to do DP Upgrade Perma-Shield® Patio Door, Narroline®
so may result in incorrect fit of frame parts. Gliding Patio Door and Sidelights

• Fasten Side Jambs to Sill through predrilled holes


using three #10 x 2-1/2" Silver Flat Head Screws, Side Jamb
making sure insect screen track on Sill is inserted
into slot on bottom of Side Jamb. Screw fastening
sequence must be followed.
Screw 1 : Fasten interior side of Side Jamb to Sill. Silicone READ
THIS INSTRUC
SCRE
W FIRTIONS

Sealant
ST

Screw 2 : Fasten exterior side of Sill to Side Jamb.


Screw 3 : Fasten center of Sill to Side Jamb.
• Clean up excess squeeze-out of Silicone Sealant.

Sill Insect
Exterior Edge Screen Track
of Sill

2
READ
THIS INST
SCRE RUCT
W FIR IONS
ST

3
1

Interior Edge
of Side Jamb
#10 x 2-1/2" Silver Screws and Locations

Exterior Side Up

5
Frame Assembly and Installation Guide
2. Attach Head Jamb To Side Jambs
• Position Head Jamb exterior side up Side Jamb
Silicone Sealant
Head Jamb

Silicone Sealant must be applied to end of Side


Jamb to help prevent water infiltration.

• Apply a 1/8" bead of Silicone Sealant to top end of Side Exterior Edge
of Head Jamb
Jambs and position against Head Jamb.

3
4
When attaching Side Jambs to Head Jamb, screw
Interior
fastening sequence must be followed. Failure to do Edge
so may result in incorrect fit of frame parts. 1 Interior Edge
of Side of Head Jamb
Jamb 2
• Fasten Head Jamb to Side Jambs through predrilled
holes using four #10 x 2-1/2" Silver Flat Head Screws.
#10 x 2-1/2" Silver Screws and Locations
Screw fastening sequence must be followed.
Screw 1 : Fasten interior side of Side Jamb to Head Jamb.
Screw 2 : Fasten interior side of Head Jamb to Side Jamb.
Screw 3 : Fasten exterior side of Head Jamb to Side Jamb.
Screw 4 : Fasten center of Side Jamb to Head Jamb.
• Clean up excess squeeze-out of Silicone Sealant.

3. Apply Side Installation Flanges

Sill
Some masonry/concrete wall and replacement Side Installation Flange
situations do not require the use of Side Installation
PLUMB - LE

Flanges. If Side Installation Flanges are not being


used proceed to Step 4.
Side Installation Flange
• Position Side Installation Flanges in groove on frame, Side Jamb Flush with Bottom of Sill
short leg pointing toward interior, flush with bottom
Exterior
of Sill. Place wood block against short leg of Side
Installation Flange and tap until fully seated.
PLU PLUMB - LEVEL - SHIM

Hammer Wood Block

6
Frame Assembly and Installation Guide
4. Attach Head Installation Flange to Head Flashing
Head Installation Flange
Head
Flashing
Ends and edges of Head Flashing are sharp. Use
caution when handling Head Flashing. Failure to do Groove
so may result in personal injury.
Flush
at Ends

Handle aluminum Head Flashing with care to Lip


avoid bending. Standard Installation

Standard Installation Modified Head


Installation Flange
• Position Head Installation Flange groove over Head
Flashing lip. Flush ends and snap into place. Long Leg Groove

Masonry/Concrete - Replacement Installation* Lip

• Score and snap long leg off Head Installation Flange,


using a sharp utility knife,
Flush
• Position modified Head Installation Flange groove over Head at Ends
Head Flashing lip. Flush ends and snap into place. Flashing
Head
Score Installation
Line Flange

* For installations where flanges are not being used. Masonry/Concrete - Replacement Installation

5. Apply Head Installation Flange/Head Flashing

Head
Head Installation Flange/Head Flashing must overlap Installation
Side Installation Flanges to the exterior to help Flange/Head
prevent water infiltration. Flashing

• Position Head Installation Flange/Head Flashing in


groove on Head Jamb, overlapping Side Installation
Flanges to the exterior. Place wood block against short
leg of Head Installation Flange/Head Flashing and tap Side Interior Edge
until fully seated. Installation of Head Jamb
• For Sidelight Installation Instructions proceed to Page Flange
14 of Panel Assembly and Installation Guide #0005309.
Exterior Side Up

7
Frame Assembly and Installation Guide
6. Apply Optional Aluminum Sill Support if Required

Sill support must be used whenever support is


needed under projecting outer edge of Sill. Support
entire length of Sill to prevent product damage.

Optional
Aluminum
Optional Aluminum Exterior Sill Extension and Sill Sill Support
Support must be applied before frame is installed.
Sill
• Slide Aluminum Sill Support onto the aluminum Sill
from one end. DO NOT secure with screws until siding
or exterior finish is applied over sheathing.

Exterior Interior

Optional
Aluminum
Sill Support*
*Shown installed.

7. Check Rough Opening


• Check dimension of rough opening for correct size.
• Check sill plate for level. Sill must be level, shim sill
plate if necessary.
• Check rough opening for plumb and level. If rough
opening is not plumb or level, correct as necessary.
• Check rough opening for square by measuring
diagonally, upper left to lower right and upper right
to lower left corner. If measurements are within 1/8",
opening is square. If rough opening is not square, Standard Construction
correct as necessary.

Rough
Exterior View Opening
Width
Rough
Opening
Height

Masonry/Concrete Construction

8
Frame Assembly and Installation Guide
8. Seal Frame, Sill and Rough Opening Side Installation Flange
Exterior Edge of Sill

Silicone Sealant must be applied to Sill and in void


between Side Installation Flange and Sill to help 3"
prevent water infiltration.
Silicone
• Apply a 1/2" bead of Silicone Sealant, 3" from exterior Sealant in Silicone Sealant
edge, full length across bottom of Sill and in void Void
between Side Installation Flange and Sill.
• Apply a 1/4” bead of Silicone Sealant to interior surface Silicone Sealant (in void)
of Head and Side Installation Flanges and at corners
where flanges intersect at Head Jamb. Silicone Sealant (full length)

Silicone
Sealant
Caulk Gun

Interior Side Up

9. Position in Rough Opening


• Center frame horizontally in rough opening from the
exterior. Apply downward pressure on Sill to spread
PLUM - LEVEL - SH

Silicone Sealant. Flange


• Clamp door frame in place.

Block Clamp

Blocking material must be used whenever support


is needed under the projecting outer edge of
SHIM

Sill. Support the entire length of Sill to prevent


Block
product damage. Exterior

• Fasten blocking material under projecting, exterior, edge Clamp


of Sill to provide support. Remove temporary blocking
Framing
prior to installation of permanent blocking or decking.
Frame
Temporary Sill
Blocking
Material Interior

Exterior Interior
Cross Section Detail

9
Frame Assembly and Installation Guide
10. Shim and Plumb Jambs
Shim

Allow 1/4" space around perimeter of unit between Clamp


exterior finish and door frame for Silicone Sealant.
Failure to do so may result in product and/or
property damage.

Side Jamb
• Insert shims between Side Jambs and framing at
each fastener location. Shims will be held in place by
fastener screws.

PLUM - LEVEL - SH
• Shims at Head Jamb are temporary. DO NOT place Interior View
shims on top of predrilled holes at Head Jamb.
Head Jamb
• Check Head and Side Jambs for level making
adjustments using shims if necessary. Jambs must be Level

PLUM - LEVEL - SHIM


plumb, level, and square. Side Jamb

Exterior View

11. Secure Frame in Rough Opening

Metal fasteners and components may corrode when


exposed to preservative-treated and fire-retardant
treated lumber. Obtain and use the appropriate
metal fasteners and hardware as called out by the
installation guide to fasten unit to any rough opening
made from preservative-treated and fire-retardant
Temporary
treated lumber. Failure to use the appropriate Shims
materials for the installation may cause a failure
resulting in injury, property or product damage.

Clamp
DO NOT nail into Head Installation Flange or Side
Installation Flanges to secure frame. Frame must
be secured through holes provided.
#10 x 2-1/2"
• Fasten frame in rough opening through holes in Head Screw
and Side Jambs using #10 x 2-1/2" Colored Screws.
Tighten until snug.
Screwdriver
Exterior View
Remove temporary shims from Head Jamb after
unit is secured. Failure to remove shims may affect
product performance and/or unit operation.

• Remove temporary shims from Head Jamb.

10
Frame Assembly and Installation Guide
12. Insulate and Seal Unit

• When insulating between the unit’s frame and


rough opening, or between units when joining,
DO NOT overpack batt insulation or overfill with
foam. Bowed jambs will result, affecting product Batt Insulation
performance and/or proper unit operation.
• Andersen® Head Flashing and Installation Flanges
DO NOT take the place of standard window and
door flashing. Unit must be properly flashed for
protection against water and air infiltration. Interior View

• Insert insulation from interior side between unit and


rough opening on all sides. DO NOT overpack batt
insulation or overfill with foam.
1/4" 1/4"
• Apply exterior finish over Installation Flanges leaving
1/4" space around perimeter of unit.
1/4"
• Apply a continuous bead of Silicone Sealant around
exterior perimeter between unit and exterior finish. Silicone Sealant

Caulk Gun

Exterior View

13. Secure Optional Aluminum Sill Support


• Fasten optional Aluminum Sill Support using
#8 x 1-1/2" Colored Screws after siding or exterior
finish is applied.

Aluminum #8 x 1-1/2"
Sill Support Colored Screw

Exterior View

11
Frame Assembly and Installation Guide
14. Attach Insect Screen Latch
Insect Screen Latch

If insect screens are NOT being used, insert screw


provided for insect screen latch into predrilled hole.

• Fasten Insect Screen Latch to frame, through predrilled


Screwdriver
hole, using screw provided.
• Hold latch in horizontal position and tighten allowing Exterior View
latch to turn freely.

15. Attach Insect Screen Stop Screw (4 Panel Doors Only)

Insect Screen Stop Screw should be applied with or


without use of insect screens.

• Fasten Insect Screen Stop Screw (#7 x 5/8") to sill


through predrilled hole using screw provided.

Insect Screen Stop Screw

Proceed To Panel Installation Guide #0005309


• Refer to instructions furnished in stationary panel carton.
• Frenchwood® impact resistant modifications are in Panel Assembly and Installation guide.
• Hardware (screws, brackets, etc.) remaining from frame installation will be used for panel installation.

12

Anda mungkin juga menyukai