14/10/2010 22:06:45
Cerrar SIS
Pantalla anterior
Producto: EXCAVATOR
Modelo: 320B L EXCAVATOR 6CR
Configuración: 320B & 320B L TRACK-TYPE EXCAVATORS 6CR00001-UP
(MACHINE) POWERED BY 3066 ENGINE
Pruebas y Ajustes
308B, 311B, 312B, 315B, 317B, 318B, 320B, 322B, 325B, 330B, M325B and W330B Excavators
Engine and Pump Control
Número de medio -RENR1998-06 Fecha de publicación -01/10/2004 Fecha de actualización -06/10/2004
i01768419
Illustration 1 g00904377
Monitor Panel
The Electronic Monitor Panel will activate. Then, the monitor will display the output that is received from the
controller. The Controller Service Program is divided into five functions. Each function is listed:
Displaying the machine conditions (engine speed, hydraulic oil temperature, power shift pressure, etc)
The electronic control components are adjusted and tested. The adjustment codes are listed: 70 and 71.
The test codes are listed: 60, 61, 62, 66 and 67.
Service codes: 80 to 8A
You should depress the switches on the monitor panel in order to start up the service program or the switches
are depressed in order to change the functions. The corresponding switch and/or switches should be depressed
until the required function is displayed on the character display.
Illustration 2 g00662936
Note: The engine can be running or the engine can be stopped, when the "Service Mode" is started. When the
engine is stopped, the starter switch must be in the ON position. You should know the procedure to start up the
"Service Mode" in advance.
1. The following switches should be depressed and held for 2 seconds or more simultaneously: travel alarm
cancel switch (22), fine control mode switch (25) and user mode switch (26) .
2. The time display and the dial display on the character display (2) will change to a "0" and a "0". The left
character position will flash.
Note: The security code must be entered within 10 seconds after the first procedure (1). Otherwise, the
time display will return. You should learn the procedure of entering the security code in advance.
a. The figure that is blinking on the character display (2) can be changed. In order to change the
figure, you should depress the boom priority mode switch (23) or the swing priority mode switch
(24).
The figure that is blinking increases (Boom priority mode switch (23) )
The figure that is blinking decreases (Swing priority mode switch (24) )
The character position that is blinking can be shifted by depressing the fine control mode switch
(25) or the user mode switch (26).
The character position that is blinking shifts to the right (Fine control mode switch (25) ).
The character position that is blinking shifts to the left (User mode switch (26) ).
5. After you enter the security code, the service mode is activated by depressing and holding the following
switches for 2 seconds or greater: travel alarm cancel switch (22), fine control mode switch (25) and user
mode switch (26). The service mode is automatically activated 10 seconds after the security code is
entered.
6. Now, the "Service Mode" is activated and the character display (2) will display "10" on the left two
character positions and "1" on the right character position.
The figure that is blinking increases (Boom priority mode switch (23) )
The figure that is blinking decreases (Swing priority mode switch (24) )
2. The position that is blinking on the character display (2) can be shifted by depressing the fine control
mode switch (25) and the user mode switch (26) .
The position that is blinking shifts to the right (Fine control mode switch (25) )
The position that is blinking shifts to the left (Swing priority mode switch (24) )
Note: Refer to the chart of Service Codes for selecting the functions for the "Service Mode".
Table 1
Service
Function
Code
10 Automatic Travel Speed Change
11 Low Temperature Control
12 Engine Speed
13 Engine Coolant Temperature
14 Hydraulic Oil Temperature
16 Digital Input
17 Software Version
18 Real Time Error Code
19 Error Log
1a Engine Speed Dial Setting Check
1b Model Name and Engine Type
1c Real Time Error Code (ATT)
1d Error Log (ATT)
20 Power Shift Pressure Command Signal
21 Displays Higher Delivery Pressure Of Main Pumps
60 Proportional Reducing Valve Sweep Test
61 Governor Actuator Sweep Test
62 ON/OFF Test Of Digital Output
66 Fixed Power Shift Pressure
67 Engine Speed Change
70 Governor Actuator Calibration
71 Proportional Reducing Valve Calibration
80 Setting Of Hydraulic Oil Type Mineral Or Biological
81 Setting Of AEC Speed
82 Setting Of AEC Delay Time
83 Setting Of Memory Mode
84 Setting Of Reduced Horsepower For Attachment Pump
2. The following switches should be depressed and held simultaneously for 2 second or more:
The service mode has been stopped, if the character display shows the position of the engine speed dial
on the right two character positions and the time is shown on the left four character positions.
Copyright 1993 - 2010 Caterpillar Inc. Thu Oct 14 22:05:15 CST 2010
Todos los derechos reservados.
Red privada para licenciados del SIS.