Tile Adhesives
— KALEKIM
— KALEKİMBEYAZ
— TECHNOFLEX
— GRANİTECH
— PROFESYONEL
— TECHNOBLOCK
— TECHNOMAX 30
— RAPİTECH
— TECHNOPOOL
— TECHNOFULL
— TECHNOLIGHT
— KALEKİMTOZUMAZ
— SUPERTECH
— TECHNOPUR
18 Kalekim ––––––––––– Tile Adhesives
1051 KALEKİM
Tile Adhesive
Description — Wipe the back side of tiles with water if dusty. Safety Advices
Cementitious ceramic tile adhesive with extended — Pour 25 kg of KALEKİM into 6.5 - 8 litres of clean — Since contains cement, irritating to eyes, respira-
open time and reduced slip. water slowly and mix to obtain a homogeneous paste tory system and skin. For further information refer to
free from lumps. A low speed mixer is recommended safety data sheet.
Fields of Application to mix. Do not add any additive which is not men-
— Floor and wall bonding of all types of ceramic tiles, tioned in the instructions for the application Storage
mosaic and decorative bricks on cementitious ren- — Allow to stand for 5-10 minutes to mature. After 1-2 — Store in dry medium. Do not stack more than 10
ders, cementitious screeds and concrete. minutes remixing, the paste is ready for application. bags on top of each other.
— Bonding of tiles on existing ceramic tiles. — Spread the mortar onto the substrate with notched
trowel of which notch size is appropriate to the tile Packaging
Properties dimension (See Notch Size Recommendation Table). — 5 kg polyethylene bag
— High adhesion strength. To obtain a good adhesion first apply a thin coat of — 25 kg multi-ply paper bags.
— Allows installation of tiles from top towards the KALEKİM with the flat side of trowel, then notch with
bottom. the toothed side of trowel.
— Extended open time. — Open time is 30 minutes. Install the tiles within this
— Easily trowellable. period with pressure. Unfavourable climatic condi-
tions (high temperature, low humidity, wind, etc) can
Application reduce this time to just a few minutes. If this period
— Substrates must be sound, free from oil, grease, exceed, scratch and discard the mortar.
and sufficiently dry. Cementitious substrates must be — Dispose mortars of which pot life is expired. Clean
cured. tools and hands with water, surfaces with a damp
— Use TAMİRART or MASTAR 10 in case of uneven cloth.
substrates to get a sound and flat surface. — Tiles installed with KALEKİM must not be subject to
water for at least 24 hours.
1052 KALEKİMBEYAZ
White Tile Adhesive
1054 TECHNOFLEX
Deformable Tile Adhesive
Description Application — Open time is 30 minutes. Install the tiles within this
High performance cementitious flexible adhesive with — Substrates must be sound, free from oil, grease, period with pressure. Unfavourable climatic condi-
extended open time and reduced slip for ceramic tiles and sufficiently dry. Cementitious substrates must be tions (high temperature, low humidity, wind, etc) can
and stones. cured. reduce this time to just a few minutes. If this period
— Use TAMİRART or MASTAR 10 in case of uneven exceed, scratch and discard the mortar.
Fields of Application substrates to get a sound and flat surface. Use GYP- — Dispose mortars of which pot life is expired. Clean
— Interior and exterior floor and wall bonding of all SASTAR on anhydrite screeds. tools and hands with water, surfaces with a damp
types and sizes of ceramic tiles, natural stone, marble, — Wipe the back side of tiles with water if dusty. cloth.
granite, porcelain ceramic, clinker, cotto on cementi- — Pour 25 kg of TECHNOFLEX into 6-7.5 litres of — Tiles installed with TECHNOFLEX must not be sub-
tious renders, cementitious screeds and concrete. clean water slowly and mix to obtain a homogeneous ject to water for at least 24 hours.
— Bonding of tiles on existing ceramic tile, granite. paste free from lumps. A low speed mixer is recom-
— Bonding of tiles on painted walls and gypsum. mended to mix. Do not add any additive which is not Safety Advices
— Bonding of ceramic tiles in swimming pools, basins mentioned in the instructions for the application — Since contains cement, irritating to eyes, respira-
and any other wet places. — Allow to stand for 5-10 minutes to mature. After 1-2 tory system and skin. For further information refer to
— Bonding of tiles on terraces and balconies. minutes remixing, the paste is ready for application. safety data sheet.
— Bonding of tiles on places where sudden tempera- — Spread the mortar onto the substrate with notched
ture changes occurs like cold storage depots and trowel of which notch size is appropriate to the tile Storage
over floor heat installations. dimension (See Notch Size Recommendation Table) — Store in dry medium. Do not stack more than 10
— Bonding of tiles on places subject to heavy traffic To obtain a good adhesion first apply a thin coat of bags on top of each other.
like shopping malls, hospitals, schools. TECHNOFLEX with the flat side of trowel, then notch
with the toothed side of trowel. Packaging
Properties — Applications of large tiles (greater than 40x40), on — 25 kg multi-ply paper bags.
— Perfect adherence. existing tiles or which are subject to frost or heavy
— Highly Deformable, resistant to temperature chan- traffic, TECHNOFLEX should be applied also on the
ges. back of tiles. (combined method)
— Can be applied on vertical surfaces even for bond-
ing of heavy tiles without sagging.
— Extended open time.
— Easily trowellable.
Technical Properties (at 23°C and 50% RH)
General Data
Appearance Grey or White powder
Shelf Life 12 months when stored in the original sealed packing
in dry place.
Application Data
Application Temperature Range (+5°C) - (+35°C)
Mixing Ratio 6 - 7.5 litres water / 25 kg powder
Pot Life Approx. 6 hours
Slip (EN 1308) ≤ 0.5 mm.
Open Time (EN 1346) After 30 minutes ≥ 0.5 N/mm²
Grouting 8 hours on wall; 24 hours after on floor
Consumption 3 - 5kg./m²
Performance Data
Tensile Adhesion Strength (EN 1348)
-initial (after 28 days) ≥ 1 N/mm²
C2TE S1 -after heat exposure ≥ 1 N/mm²
-after immersion in water ≥ 1 N/mm²
Certificates of Quality:
-after freeze/thaw cycles ≥ 1 N/mm²
TS EN 12004, Class C2TE, S1 Deformability (EN 12002) ≥ 2.5 mm-S1 Deformable
C: Cementitious
2: Improved
Service Temperature Range (after final cure) (-40°C) - (+80°C)
T: Reduced slip Dangerous Substances (EN 12004) Complies
E: Extended Open Time
S1: Deformable
Reaction to Fire A1
Kalekim ––––––––––– Tile Adhesives 21
1055 GRANİTECH
Granite Tile Adhesive
Description GYPSASTAR on anhydrite screeds. period exceed, scratch and discard the mortar.
High performance cementitious adhesive with — Wipe the back side of tiles with water if dusty. — Dispose mortars of which pot life is expired. Clean
reduced slip. — Pour 25 kg of GRANİTECH into 5.5-7 litres of clean tools and hands with water, surfaces with a damp
water slowly and mix to obtain a homogeneous paste cloth.
Fields of Application free from lumps. A low speed mixer is recommended — Tiles installed with GRANİTECH must not be
— Interior and exterior floor and wall bonding of all to mix. Do not add any additive which is not mentioned subject to water for at least 24 hours.
types and sizes of ceramic tiles, granite, porcelain in the instructions for the application
ceramic, cotto, clinker on cementitious renders, — Allow to stand for 5-10 minutes to mature. After 1-2 Safety Advices
cementitious screeds and concrete. minutes remixing, the paste is ready for application. — Since contains cement, irritating to eyes,
— Bonding of tiles on existing ceramic tiles or marble. — Spread the mortar onto the substrate with notched respiratory system and skin. For further information
— Bonding of tiles on places subject to heavy traffic trowel of which notch size is appropriate to the tile refer to safety data sheet.
like shopping malls, hospitals, schools. dimension (See Notch Size Recommendation Table)
To obtain a good adhesion first apply a thin coat of Storage
Properties GRANİTECH with the flat side of trowel, then notch — Store in dry medium. Do not stack more than 10
— Perfect adherence. with the toothed side of trowel. bags on top of each other.
— Can be applied on vertical surfaces even for — Application of large tiles (greater than 40x40), on
bonding of heavy tiles without sagging. existing tiles or which are subject to frost or heavy Packaging
— Easily trowellable. traffic, GRANİTECH should be applied also on the — 25 kg multi-ply paper bags.
back of tiles. (combined method)
Application — Open time is 20 minutes. Install the tiles within
— Substrates must be sound, free from oil, grease, this period with pressure. Unfavourable climatic
and sufficiently dry. Cementitious substrates must be conditions (high temperature, low humidity, wind,
cured. etc) can reduce this time to just a few minutes. If this
— Use TAMİRART or MASTAR 10 in case of uneven
substrates to get a sound and flat surface. Use
1056 PROFESYONEL
Granite Tile Adhesive
1058 TECHNOBLOCK
Aerated Concrete Adhesive
Description — Pour 25 kg of TECHNOBLOCK into 8-9 litres of — Dispose mortars of which pot life is expired. Clean
Cementitious masonry mortar for bonding high water clean water slowly and mix to obtain a homogeneous tools and hands with water, surfaces with a damp
absorbing construction elements like aerated con- paste free from lumps. (A low speed mixer is recom- cloth.
crete. mended to mix).
— Allow to stand for 5-10 minutes to mature. After Safety Advices
Fields of Application remixing, the paste is ready for application. — Since contains cement, irritating to eyes, respira-
— Bonding of aerated concrete and any other high — Spread the mortar onto the substrate with notched tory system and skin. For further information refer to
water absorbing construction elements. trowel of which notch size is 10x10x10mm. While lay- safety data sheet.
ing the blocks, vertical and horizontal joints should
Properties have maximum 3 mm width and fill them completely Storage
— Perfect adherence with TECHNOBLOCK. — Store in dry medium. Do not stack more than 10
— Easily trowellable. — Open time is 10-15 minutes. Lay the blocks within bags on top of each other.
— Labor-cost effective. this 7 period with a firm pressure. Unfavourable cli-
matic conditions (high temperature, low humidity, Packaging
Application wind, etc) can reduce this time to just a few minutes. — 25 kg multi-ply paper bags.
— Substrates must be sound, free from oil, grease, If this period exceed, scratch and discard the mortar.
and sufficiently dry. Cementitious substrates must be
cured.
1060 TECHNOMAX 30
Two Component Highly Deformable Tile Adhesive
Description — Wipe the back side of tiles with water if dusty. — In installation of large size tiles, lay the tiles hori-
Two component, high performance cementitious flex- — Pour 25 kg. of powder component into 5.75 litres of zontally and do not start to lay upper row before the
ible adhesive with reduced slip and extended open- clean liquid slowly and mix to obtain a homogeneous below one cured. Leave an expansion joint at every 4
time for ceramic tiles and stones. paste free from lumps. A low speed mixer is recom- meter and use KALEPOLYMAS.
mended to mix. Do not add any additive which is not — Dispose mortars of which pot life is expired. Clean
Fields of Application mentioned in the instructions for the application tools and hands with water, surfaces with a damp
— Exterior bonding of ceramic, granite or porcelain — Allow to stand for 5-10 minutes to mature. After 1-2 cloth.
ceramics sized 40x40 cm up to 30 meter and 60x60 minutes remixing, the paste is ready for application. — Tiles installed with TECHNOMAX 30 must not be
cm. up to 15 meter height. — Spread the mortar onto the substrate with notched subject to water for at least 24 hours.
— Interior and exterior floor and wall bonding of all trowel of which notch size is appropriate to the tile
types and sizes of ceramic tiles, natural stone, marble, dimension. (See Notch Size Recommendation Table) Safety Advices
granite, porcelain ceramic, clinker, cotto on cementi- To obtain a good adhesion first apply a thin coat of — Since contains cement, irritating to eyes, respira-
tious renders, cementitious screeds and concrete. TECHNOMAX 30 with the flat side of trowel, then tory system and skin. For further information refer to
— Bonding of tiles on places subject to heavy traffic notch with the toothed side of trowel. Application safety data sheet.
like shopping malls, hospitals, schools. of large tiles (greater than 40x40), on existing tiles or
which are subject to frost or heavy traffic, TECHNO- Storage
Properties MAX 30 should be applied also on the back of the — Powder component: Store in dry medium. Do not
— Perfect adherence. tiles. (combined method) stack more than 10 bags on top of each other.
— Highly deformable, resistant to temperature chang- — Open time is 30 minutes. Install the tiles within this — Liquid component: Store in temperatures 5°C to
es. period with a firm pressure. Unfavourable climatic 35°C in original sealed packing.
— Resistant to all climatic conditions. conditions (high temperature, low humidity, wind, etc)
— Can be applied on vertical surfaces even. For can reduce this time to just a few minutes. If this pe- Packaging
bonding of heavy tiles without sagging. riod exceed, scratch and discard the mortar. — Powder component: 25kg multi-ply paper bags,
— Extended open time. Liquid component: 5.75lt drums.
— Easily trowellable.
Application
— Substrates must be sound, free from oil, grease, Technical Properties (at 23°C and 50% RH)
and sufficiently dry. Cementitious substrates must be General Data
cured. Appearance 1st component: Grey powder,
— Use TAMİRART or MASTAR 10 in case of uneven 2nd component: White liquid
substrates to get a sound and flat surface. Use Shelf Life 12 months when stored in the original sealed packing in dry
place
GYPSASTAR on anhydrite screeds.
Application Data
Application Temperature Range (+5°C) - (+35°C)
Mixing Ratio 5.75 litres liquid / 25 kg powder
Pot Life 1.5 hours
Slip (EN 1308) ≤ 0.5 mm
Open Time (EN 1346) After 30 minutes ≥ 0.5 N/mm²
Grouting 8 hours on wall; 24 hours after on floor
Set to Light Foot Traffic 24 hours
Consumption 4.5 - 6.5 kg/m² (Combined Method)
Performance Data
Tensile Adhesion Strength (EN 1348)
-initial (after 28 days) ≥ 1 N/mm²
C2TE S2 -after heat exposure ≥ 1 N/mm²
-after immersion in water ≥ 1 N/mm²
1061 RAPİTECH
Fast Setting Tile Adhesive
Description — Use TAMİRART or MASTAR 10 in case of uneven riod exceed, scratch and discard the mortar.
High performance, rapid setting and reduced slip ce- substrates to get a sound and flat surface. Use — Dispose mortars of which pot life is expired. Clean
mentitious adhesive for ceramic tiles and stones. GYPSASTAR on anhydrite screeds. tools and hands with water, surfaces with a damp
— Wipe the back side of tiles with water if dusty. cloth.
Fields of Application — Pour 25kg of RAPİTECH into 6-7 litres of clean wa- — If joints can be grouted with FUGAFLEX or
— Interior and exterior floor and wall bonding of all ter slowly and mix to obtain a homogeneous paste FUGASİM, the site may be open for use within 1 day.
types and sizes of ceramic tiles, natural stone and free from lumps. A low speed mixer is recommended — Tiles installed with RAPİTECH must not be subject
decorative bricks on cementitious renders, cementi- to mix. Do not add any additive which is not men- to water for at least 3-4 hours.
tious screeds and concrete. tioned in the instructions for the application.
— Rapid tiling of places like public buildings, cafes, — Allow to stand for 5 minutes to mature. After 1-2 Safety Advices
supermarkets, airports, that has to be ready for use minutes remixing, the paste is ready for application. — Since contains cement, irritating to eyes, respira-
within one day. — Spread the mortar onto the substrate with notched tory system and skin. For further information refer to
— Bonding of tiles on existing ceramic tiles. trowel of which notch size is appropriate to the tile safety data sheet.
dimension (See Notch Size Recommendation Table)
Properties To obtain a good adhesion first apply a thin coat of Storage
— Fast setting, RAPİTECH with the flat side of trowel, then notch — Store in dry medium. Do not stack more than 10
— Perfect adherence. with the toothed side of trowel. Application of large bags on top of each other.
— Can be applied on vertical surfaces even for bond- tiles (greater than 40x40), on existing tiles or which
ing of heavy tiles without sagging. are subject to frost or heavy traffic, RAPİTECH should Packaging
— Easily trowellable. be applied also on the back of the tiles. (combined — 25kg multi-ply paper bags.
method)
Application — Open time is 15 minutes. Install the tiles within this
— Substrates must be sound, free from oil, grease, period with a firm pressure. Unfavourable climatic
and sufficiently dry. Cementitious substrates must be conditions (high temperature, low humidity, wind, etc)
cured. can reduce this time to just a few minutes. If this pe-
1062 TECHNOPOOL
Waterproofing Tile Adhesive
Description — Use TAMİRART or MASTAR 10 in case of uneven — When TECHNOPOOL is used not only as an ad-
High performance, flexible, water resistant cementi- substrates to get a sound and flat surface. Use hesive but also as a water insulation material, apply
tious adhesive with extended open time and reduced GYPSASTAR on anhydrite screeds. mortar both on the substrate and on back side of tiles
slip for ceramic tiles and stones. — Wipe the back side of tiles with water if dusty. (combined method). Alternatively, first apply a layer of
— Pour 25 kg of TECHNOPOOL into 5 – 5.5 litres of 1 - 2 mm of TECHNOPOOL with reinforcement mesh
Fields of Application clean water slowly and mix to obtain a homogeneous at corners, then install the tiles after 24 hours.
— Interior and exterior floor and wall bonding of all paste free from lumps. A low speed mixer is recom- — Dispose mortars of which pot life is expired. Clean
types and sizes of ceramic tiles, natural stone, marble, mended to mix. Do not add any additive which is not tools and hands with water, surfaces with a damp
granite, porcelain ceramic, clinker, cotto on cementi- mentioned in the instructions for the application cloth.
tious renders, cementitious screeds and concrete. — Allow to stand for 5-10 minutes to mature. After 1-2 — Tiles installed with TECHNOPOOL must not be
— Bonding of all types and sizes of tiles and glass mo- minutes remixing, the paste is ready for application. subject to water for at least 24 hours.
saics in swimming pools, Turkish baths, water tanks, — Spread the mortar onto the substrate with notched
basins and any other wet place. trowel of which notch size is appropriate to the tile Safety Advices
— Bonding of ceramic tiles or granite on existing dimension (See Notch Size Recommendation Table) — Since contains cement, irritating to eyes, respira-
granite, ceramic, marble. To obtain a good adhesion first apply a thin coat tory system and skin. For further information refer to
— Bonding of tiles on places where sudden tempera- of TECHNOPOOL with the flat side of trowel, then safety data sheet.
ture changes occurs like cold storage depots and notch with the toothed side of trowel. Application
over floor heat installations. of large tiles (greater than 40x40), on existing tiles Storage
— Bonding of tiles on places subject to heavy traffic or which are subject to frost or heavy traffic, TECH- — Store in dry medium. Do not stack more than 10
like shopping malls, hospitals, schools. NOPOOL should be applied also on the back of the bags on top of each other.
tiles (combined method).
Properties — Open time is 30 minutes. Install the tiles within this Packaging
— Perfect adherence. period with a firm pressure. Unfavourable climatic — 25 kg multi-ply paper bags
— Highly deformable, resistant to temperature chang- conditions (high temperature, low humidity, wind, etc)
es. can reduce this time to just a few minutes. If this pe-
— Waterproofing. riod exceed, scratch and discard the mortar.
— Extended open time.
— Can be applied on vertical surfaces even for bond-
ing of heavy tiles without sagging.
— Easily trowellable. Technical Properties (at 23°C and 50% RH)
General Data
Application Appearance Grey or White powder
— Substrates must be sound, free from oil, grease, Shelf Life 12 months when stored in the original sealed packing in dry
place
and sufficiently dry. Cementitious substrates must be
Application Data
cured.
Application Temperature Range (+5°C) - (+35°C)
Mixing Ratio 5 – 5.5 litres water / 25 kg powder
Pot Life 6 hours
Slip (EN 1308) ≤ 0.5 mm
Open Time (EN 1346) After 30 minutes ≥ 0.5 N/mm²
Grouting 8 hours on wall; 24 hours after on floor
Consumption 3 - 5 kg/m²
Performance Data
Tensile Adhesion Strength (EN 1348)
-initial (after 28 days) ≥ 1 N/mm²
C2TE S2 -after heat exposure ≥ 1 N/mm²
-after immersion in water ≥ 1 N/mm²
Certificates of Quality:
-after freeze/thaw cycles ≥ 1 N/mm²
TS EN 12004, Class C2TE, S2 Deformability (EN 12002) ≥5mm-S2 Highly deformable
C: Cementitious
2: Improved
Service Temperature Range (after final cure) (-40°C) - (+80°C)
T: Reduced Slip Dangerous Substances (EN 12004) Complies
E: Extended Open Time
S2: Highly Deformable
Reaction to Fire A1
28 Kalekim ––––––––––– Tile Adhesives
1066 TECHNOFULL
Fast Setting Pourable Tile Adhesive
1069 TECHNOLIGHT
Lightweight, Highly Deformable Tile Adhesive
Description — Highly deformable, resistant to temperature changes. — Application of large tiles (greater than 40x40), on
Cementitious, high performance, flexible, lightweight tile — Can be applied on vertical surfaces even for bonding existing tiles or which are subject to frost or heavy
adhesive including rubber and nano technological addi- of heavy tiles without sagging. traffic, TECHNOLIGHT should be applied on the back of
tives with extended open time and reduced slip. — Extended open time. the tiles (combined method).
— Easily trowellable. — Open time is 30 minutes. Install the tiles within this
Fields of Application period with a firm pressure. Unfavourable climatic condi-
— Interior and exterior floor and wall bonding of all types Application tions (high temperature, low humidity, wind, etc) can re-
and sizes of ceramic tiles, natural stone, marble, granite, — Substrates must be sound, free from oil, grease, and duce this time to just a few minutes. If this period exceed,
porcelain ceramic, clinker, cotto on cementitious renders, sufficiently dry. scratch and discard the mortar.
cementitious screeds and concrete. — Use TAMİRART or MASTAR 10 in case of any loose and — Dispose mortars of which pot life is expired. Clean
— Bonding of tiles on existing ceramic tile, granite. uneven substrates to get a sound and flat surface. tools and hands with water, surfaces with a damp cloth.
— Bonding of tiles on painted walls and gypsum. — Wipe the back side of tiles with water if dusty. — Tiles installed with TECHNOLIGHT must not be subject
— Bonding of ceramic tiles in swimming pools, basins and — Apply KALEKİM DOLGULU ASTAR on plaster surfaces to water for at least 24 hours.
any other wet places. prior to the application. Use GYPSASTAR on anhydrite
— Bonding of tiles on terraces and balconies. screeds. Safety Advices
— Bonding of tiles on places where sudden temperature — Pour 15 kg of TECHNOLIGHT into 6-6.5 litres of clean — Since contains cement, irritating to eyes, respiratory
changes occurs like cold storage depots, on walls of ov- water slowly and mix to obtain a homogeneous paste free system and skin. For further information refer to safety
ens.and over floor heat installations. from lumps. A low speed mixer is recommended to mix. data sheet. Do not add any component which is not men-
— Bonding of tiles on places subject to heavy traffic like Do not add any additive which is not mentioned in the tioned in application.
shopping malls, hospitals, schools. instructions for the application
— Allow to stand for 5-10 minutes to mature. After 1-2 Storage
Properties minutes remixing, the paste is ready for application. — Store in dry medium. Do not stack more than 10 bags
— Approx. 40% less consumption than standard adhe- — Spread the mortar onto the substrate with notched on top of each other.
sives. Thus, accomplish the same job with 15 kg package trowel of which notch size is appropriate to the tile dimen-
instead of 25 kg standard adhesive. sion (See Notch Size Recommendation Table) To obtain a Packaging
— High flexibility with rubber fillers. good adhesion first apply a thin coat of TECHNOLIGHT — 15 kg multi-ply paper bags with handles.
— With its nano technological raw materials, it has high with the flat side of trowel, then notch with the toothed
adhesion strength. side of trowel.
— Easy to carry with light weight and package with han-
dles.
Technical Properties (at 23°C and 50% RH)
General Data
Appearance Grey powder
12 months when stored in the original sealed packing in dry
Shelf Life
place.
Application Data
Application Temperature Range (+5°C) – (+35°C)
Mixing Ratio 6 - 6.5 lt water / 15 kg powder
Pot Life 6 hours
Slip (EN 1308) ≤ 0.5mm
Open Time (EN 1346) After 30 minutes ≥ 0.5 N/mm²
Grouting 8 hours on wall; 24 hours after on floor
Consumption 1.5-2.5 kg/m²
Performance Data
Tensile Adhesion Strength (EN 1348)
C2TE S2 -initial (after 28 days) ≥ 1 N/mm²
Environmentally -after heat exposure ≥ 1 N/mm²
Friendly
-after immersion in water ≥ 1 N/mm²
Certificates of Quality:
-after freeze/thaw cycles ≥ 1 N/mm²
TS EN 12004 Class C2TE, S2 Deformability (EN 12002) ≥ 5 mm - S2 Highly deformable
C: Cementitious
2: Improved
Service Temperature Range (after final cure) (-40°C) - (+80°C)
T: Reduced Slip Dangerous Substances (EN 12004) Complies
E: Extended Open Time
S2: Highly Deformable
Reaction to Fire A1
30 Kalekim ––––––––––– Tile Adhesives
1070 KALEKİMTOZUMAZ
Dust-Free Ceramic Tile Adhesive
1230 SUPERTECH
Ready to Use Tile Adhesive
1411 TECHNOPUR
Solvent-free Polyurethane Adhesive
Description — For floor heating systems, the heating should start Safety Advices
Two component, solvent-free polyurethane based ten days earlier and be stopped at the time of appli- — Contains Difenylmethane 4.4´ - diisosyanate which
multi-purpose adhesive. cation. System can be reoperated 72 hours after the can be harmful.
application. — Do not breathe vapor. Use in well ventilated areas.
Fields of Application — Mix 6.250 kg component A with 0.750 kg compo- — In case of contact with skin and eyes rinse imme-
— Bonding ceramic, granite ceramic, on concrete, nent B until a homogeneous color is obtained. diately with plenty of water and seek medical advice.
metal, fibre-cement, wood, plasterboard surfaces. — Spread the mixture onto the substrate with notched — Wear suitable protective clothing, gloves and eye
— Bonding parquet. trowel of 4x4x4 mm size. protection.
— Bonding on floors over floor heating installations. — In bonding, sizes 40x40 cm or larger, apply the mix- — Keep away from children.
— Bonding thin tiles (Kalesinterflex®) reinforced with ture using backbuttering method. — Keep products as lids closed.
fibre mesh. — Bonding of tiles and parquets on the substrate sur-
faces must be applied in 45-60 minutes. Storage
Properties — Dispose mortars of which pot life is expired. Clean — Store in dry medium.
— Solvent-free. tools and surface with polyurethane cleaning materi-
— Excellent flexibility. als. Packaging
— Perfect adherence — 7 kg pail (2 components).
Application
— Substrates must be sound, free from oil, grease,
and sufficiently dry. Cementitous substrates must be
cured.
— Use TAMİRART or MASTAR 10 in case of any loose
and uneven substrates to get a sound and flat sur-
face.