Note: The acceptable tolerance is more stringent than demanded by DIN 18202
A measurement protocol must be created by an independent surveyor for the entire adjusting bay.
If the vehicle lane is with tiled floor; the adjustment bay must be finished before the workshop floor is installed. L 70.50.6, hot galvanized
Anchor dimensions and distance in
acc. with statical information
upper edge, 53 587 53 1000 Inside dimension 5500 shimming
upper edge, floor flat anchor
naked floor ±0.00 40.5 L=7,5 cm
-0.085
Vehicle lane surface must be plane and level in height and inclination, max. deviation 1 mm/ m in all directions.
Aluminium-
Note: The acceptable tolerance is more stringent than demanded by DIN 18202
A measurement protocol must be created by an independent surveyor for the entire adjusting bay.
passleiste
geschraubt
IPE 80 This incudes plan no.
If the vehicle lane is with tiled floor; the adjustment bay must be finished before the workshop floor is installed. L 70.50.6, hot galvanized E-D-BA-06 Rails for headlamp adjusting
E-I 01 Notes / Information
20
Anchor dimensions and distance in
16
46
Langloch 15 mm
acc. with statical information vergießen
85
L-Profil 65.65.7 5 53 116
65
upper edge, 1200 Inside dimension 600 1200 Inside dimension shimming
upper edge, floor flat anchor
naked floor ±0.00 40.5 L=7,5 cm
max. Bohrloch-
tiefe beachten
-0.085
DRE workshop planning/equipment
Implementation of functional workshop concepts
1.00 5.360.75.3
Section B-B scale 1:20 Detail scale 1:5
Rails for adjusting device floor integrated.
50
50
50
Our services:
Able to cross with workshop equipment and withstanding vehicle traffic.
5500
extra- kompakt
53 607 53
53 607 53
53 607 53
Citan Citan
oil supply and disposal,
2000 1500
Citan
lang
extra-kompakt
compressed air system
Sprinter A1
lang
Vito Vito
lang
Vito
- Advice and consulting for workshop planning/equipment
Sprinter A2
500
500
lang
496
800
1000
1500
Sprinter A3
- Project support of workshop equipment for new buildings and conversions
Sprinter A4
250 500 500 500 250
1000
500 500
1100
2012
state frames
Measuring L 70.50.6
state frames
1000
L 70.50.6
500 500 500 500
T-steel
1100
in extracts is forbidden.
20.20.3
B Across sticks B This plan is a binding orientation aid for the contractor for drafting the workshop equipment planning only. In the event of any
contradictions or other irregularities, the contractor must notify the DRE department immediately and before execution of the planning in
T-steel writing. Daimler AG does not accept any responsibility for the workshop planning and/or execution of construction work, even where this has been expressly
20.20.3 approved.
1000
988
min. 7000
min. 7000
min. 7000
The specifications and standards contained in the plan may alter subsequently. Color deviations are print-specific. This plan is used internationally.
Statements on statutory, legal and tax regulations and consequences are only valid for the Federal Republic of Germany at such time as when
the plans are compiled. Therefore, become informed about the regulations and consequences applicable in other countries before realization of the
5512
1100
specifications and standards by means of your local architects, technical planners or appraisers. CI specifications of D-AG (BC/FP) must be observed.
500 500 500 500
80 5.360.75.3
Standardplan
2500 Inside dimension
500
1250
50
50
50
construction/installation/equipment
70
500
1100
2512
500
2000
Mercedes-Benz
1250
500
1100
1000
Planning:
Entrance help
Entrance help
500
kompakt
Daimler Real Estate (DRE) Building 22
yellow mark
yellow mark
yellow mark
Entrance help
Citan
HPC: 0120 Epplestraße 225
Citan
lang
350 500 350 350 500 350 350 500 350 350 500 350 D-70546 Stuttgart, Germany Stuttgart - Möhringen
extra-kompakt
extra-
Citan
Sprinter A1
lang
1200 600 1200
2500
1200 600 1200 Telephone: +49-(0)711-17-90673
Vito Vito
Inside dimension Inside dimension
lang
Vito
Inside dimension Inside dimension
Sprinter A2
Mobil: +49-(0)160-8670489
lang
A
Planning content:
Ground floor 3 variants, Planning number:
Sprinter A3
Sprinter A4
Sections A-A and B-B, E-T09
1000 1000 1000 Overview vehicle layout Index:
Sprinter Vito Citan
drawn: checked: approved:
Planning status:
Rehr R. Meyer G. Hausmann
Adjustment bay with frame scale 1:50 Wheel alignment combined scale 1:50 Work bay with lift scale 1:100 date: planning format: scale:
Adjustment bay with frame scale 1:50 in combination with a lift with headlight adjustment December ´15 420 / 770 1:5/1:20/1:50/1:100
This drawing is subject to the regulations pertaining to copyright protection
H/B = 420 / 770 (0.32m²) Allplan 2015