2007) ME-20
SERVICE NOTES
Guitar Multiple Effects
Issued by RJA
ME-20
Table of Contents
Cautionary Notes ..............................................................2 Test Mode .........................................................................10
Specifications .....................................................................3 Block Diagram .................................................................15
Location of Controls .........................................................4 Circuit Board (Main 1/2)................................................16
Location of Controls Parts List........................................5 Circuit Board (Main 2/2)................................................17
Exploded View ..................................................................6 Circuit Diagram (Main Board) ......................................18
Exploded View Parts List.................................................7 Error Messages ................................................................20
Parts List .............................................................................8
Checking the Version Number........................................9
Saving and Loading Users Data......................................9
Factory Reset Instructions..............................................10
System Software Updating Instructions ......................10
Revise Information
Sep. 25, 2007
P.14 - The whole contents of this segment were revised.
"10. Expression-pedal Adjustment"
Cautionary Notes
Part Replacement
When replacing components near the power-supply circuit or a heat-
generating circuit (such as a circuit provided with a heat sink or including a
cement resistor), carry out the procedure according to the instructions with
respect to the part number, direction, and attachment position (mounting so as
to leave an air gap between the component and the circuit board, etc.).
Parts List
A component whose part code is ******** cannot be supplied as a service part
because one of the following reasons applies.
• Because it is supplied as an assembled part (under a different part code).
• Because a number of circuit boards are grouped together and supplied as
a single circuit board (under a different part code).
• Because supply is prohibited due to copyright restrictions.
• Because reissuance is restricted.
• Because the part is made to order (at current market price).
Circuit Diagram
In the circuit diagram, “NIU” is an abbreviation for “NOT IN USE.” The circuit
board and circuit-board diagram show silkscreened indications, but no
components are mounted.
2
May, 2007 ME-20
Specifications Dimensions
294 (W) x 179 (D) x 54 (H) mm
ME-20(40318): Guitar Multiple Effects 11-5/8 (W) x 7-1/16 (D) x 2-1/8 (H) inches
Maximum height:
294 (W) x 179 (D) x 74 (H) mm
AD Conversion
11-5/8 (W) x 7-1/16 (D) x 2-15/16 (H) inches
24-bit + AF method (*)
Weight
DA Conversion
1.6 kg / 3 lbs 9 oz (including batteries)
24-bit
Accessories
Sampling Frequency
• Owner’s Manual English (#G6027123R0)
44.1 kHz • Patch List (#********)
Note: The Patch list is included only in the initial production lot (for
English text as well).
Patches
Note: Starting with the subsequent production lot, the Patch list is
30 (user) included in the owner’s manual.
• Dry Batteries (Alkaline: LR6 (AA) type) x 6 (#********)
Output Impedance
* 0 dBu = 0.775 Vrms
2 k ohm
Jacks
INPUT jack (1/4” phone type)
AUX IN jack (Stereo miniature phone type)
OUTPUT jacks L/MONO, R (1/4” phone type)
PHONES jack (Stereo 1/4” phone type)
FOOT SW jack (1/4” TRS phone type)
AC Adaptor jack
Power Supply
DC 9 V: Dry batteries (R6/LR6 (AA) type) x 6,
AC Adaptor (PSA series: Optional)
Current Draw
90 mA
* Expected battery life under continuous use:
Alkaline: 13 hours, Carbon: 3.5 hours
These figures will vary depending on the actual conditions of use.
3
May, 2007 ME-20
Location of Controls
[Panel]
fig.me-20-panel.eps
[Rear]
fig.me-20-rear.eps
1 2 3 3 4 1 5
4
May, 2007 ME-20
[Panel]
[Rear]
5
May, 2007 ME-20
Exploded View
fig.me-20-bunkai.eps
6
May, 2007 ME-20
7
May, 2007 ME-20
Parts List
NOTE: The parts marked # are new. (initial parts) The description "Q'TY" means a necessary number of the parts per one product.
CHASSIS
G2357304R0 VR PEDAL PLATE TOE 1
G2357303R0 VR PEDAL PLATE HEEL 1
G2027945R0 BOTTOM COVER 1
G2217782R0 PANEL PLATE 1
G2017646R0 TOP CASE 1
G2187914R0 VR PEDAL 1
KNOB,BUTTON
G2477520R0 R-KNOB 5
G2497013R0 KEY UNIT 1
SWITCH
01780101 TACT SWITCH SKQKABD010 SW1,SW2,SW3,SW4,SW5,SW6,SW7,SW8,S 13
W9,SW10,SW11,SW12,SW13
G2187915R0 SW PEDAL 3
JACK,EXT TERMINAL
03239801 6.5MM JACK HTJ-064-12I JK1,JK3 2
03344701 6.5MM JACK HTJ-064-12DS JK4,JK6 2
F3449714R0 6.5MM JACK HTJ-064-05A JK5 1
F3439868R0 MINI JACK HTJ-035-23DBS(STEREO) JK2 1
13449717R0 ADAPTOR JACK HEC2392-01-150 JK7 1
PWB ASSY
75E243P0R0 MAIN SHEET ASSY 1
IC
01125012 IC (BIPOLAR OP AMP) NJM4556AM IC1 1
00346445 IC (BIPOLAR OP AMP) NJM2100M(TE3) IC3 1
04345889 IC(OP AMP) NJM14558M IC2 1
DIODE
15029281R0 LED L-34HDSL LED3,LED4,LED5,LED6,LED7,LED8,LED9, 10
LED10,LED11,LED12,
F5229810R0 LED L-323SRDT LED1,LED2 2
F5029412R0 7SEG LED A-552SR BW LED13 1
POTENTIOMETER
F3229201R0 POTENTIOMETER RV110F-40E1-15A-B50K-005 VR1,VR2,VR3,VR4,VR5 5
01016167 11M/M ROTARY POTENTI- RK11K1140AFG 10KX1 VR6 1
OMETER
CRYSTAL,RESONATOR
F5299525R0 CRYSTAL HC49SMÅ@16.9344MHZ X1 1
WIRING, CABLE
F3467052R0 WIRING BATTERY 2P 100MM 1
F3467051R0 WIRING 3P 130MM CN4 1
SCREWS
H5039515R0 NUT U NUT M6 BZC 1
H5019110R0 SCREW 3X6 PAN TAPPING B1 ZC 14
H5019115R0 SCREW 3X8 PAN TAPPING B1 BZC 2
H5039520R0 NUT M9 1
H5039520R0 NUT M9 5
H5049001R0 SCREW M6X60 HEX SOCKET CAP BZC 1
H5049002R0 SCREW M3X6 HEX SOCKET BUTTON NI 5
H5029331R0 SCREW 3X8 BINDING TAPTITE S BZC 1
8
May, 2007 ME-20
SCREWS
H5029330R0 SCREW 3X8 BINDING TAPTITE P BZC 4
H5029325R0 SCREW 3X6 B1FEBC 7
H5039205R0 TOOTH WASHER 9.1X13 4
H5039122R0 PLAIN WASHER 6X13X1 BZC 1
G2147898R0 BOLT HOLDER 2
G2147874R0 BOLT HOLDER 2
H5039510R0 NUT M9X12X2T NI 4
H5039158R0 WASHER M9X14X0.5T NI 4
PACKING
G2627789R0 PACKING CASE 1
G2267632R0 PAD L 1
G2267633R0 PAD R 1
MISCELLANEOUS
G2357305R0 FOOT VR PEDAL 2
G2217775R0 LABEL SW PEDAL 3 1
G2217776R0 LABEL SW PEDAL 2 1
G2217777R0 LABEL SW PEDAL 1 1
G2637117R0 VR SPACER SUS 1
G2357120R0 FOOT H=5 4
G2199514R0 LED SPACER 7MM 3
G2567170R0 7-SEG COVER 1
G2017620R0 BATTERY CASE 1
G2017621R0 BATTERY COVER 1
G2257130R0 BATTERY INSULATING 1
SHEET
G2177307R0 BATTERY TERMINAL(+/-) 1
G2177308R0 BATTERY TERMINAL(+) 1
G2177309R0 BATTERY TERMINAL(-) 1
G2357111R0 CUSHION R 1
G2147127R0 DC JACK HOLDER 1
G2257203R0 JACK COVER 1
G2357109R0 PEDAL FOOT 3
G2147897R0 PIN STAY 1
G2147806R0 STAY (POM) 1
G2177103R0 SUPPORT SPRING 3
ACCESSORIES (Standard)
G6027123R0 OWNER’S MANUAL ENGLISH 1
G6017469R0 OWNER’S MANUAL JAPANESE 1
2. Connect an AC adapter.
3. While holding down [EDIT/EXIT] and [WRITE], insert a plug into the
INPUT jack to power up the unit.
Note: Continue to hold down [EDIT/EXIT] and [WRITE] until the version is
displayed.
5. Switch off the power either by detaching the plug from the INPUT jack or
by disconnecting the AC adapter.
9
May, 2007 ME-20
displayed.
12. Forcefully depress the expression pedal, and make sure the WAH LED
lights up.
13. Forcefully depress the expression pedal again, and make sure the WAH
LED goes dark. DC IN FOOT SW PHONES
OUTPUT
AUX INPUT
L R
14. Press [WRITE] to advance the display on the 7-segment display. ME-20
Make sure that [Gt] is shown on the 7-segment display.
Note: This [Gt] signifies that the unit is the ME-20.
15. Switch off the power by detaching the plug from the INPUT jack. Entering Test Mode
16. This completes the factory reset. The starting location of the Test mode can be varied by modifying how the
switches are pressed when the unit is powered up (by insertion of a plug into
the INPUT jack).
10
May, 2007 ME-20
Because detaching the plug connected to the INPUT jack while in the Test
mode switches off the power, interposing a switch unit or the like can facilitate 3. VR Check
operations. (For details, refer to the Connection Diagram on the previous
1. Make sure that [1. ] is displayed on the 7-segment display.
page.)
Note: If the dot is not displayed, it is possible that the VR is not detected
as being at its MIN (minimum) position.
1. Version Check Adjust all VR controls to the MIN position and make sure that the dot
lights up.
1. Power up the unit by inserting a plug into the INPUT jack while holding
Check the VR controls in this sequence, from left to right: VR1, VR2, VR3,
down [OD/DS] + [MOD].
VR4, VR5 (MASTER), and EXP_VR.
After powerup, the version is displayed.
2. Turn the VR control to the 9 o’clock, then 12 o’clock, then 3 o’clock
2. Version Check
positions and verify that bars are displayed on the 7-segment display.
The version of the software appears on the 7-segment display.
Adjusting a VR control to its MAX position causes operation to transfer
Make sure the software is at the latest version. to the check of the next VR.
To transfer execution to the next VR, return the first VR to its MIN
position, then go to the next VR.
3. Press [ ].
Checksum values (upper and lower) are displayed in time with the
4. Voltage Check
illumination cycle of the TUNER LED. 1. Changing the power-source voltage to 9 V
If the checksum is correct, you can advance to the next section using [ ]. Verify that the voltage value is within the range of 8.5 to 8.9 V.
4. Press [ ]. 2. Changing the power-source voltage to 7.5 V
Execution is transferred to the SW (switch) and LED check. Verify that the voltage value is within the range of 7.1 to 7.4 V.
Note: To skip measurement, press [ ] to advance to the check of the
foot switch.
2. SW/LED Check
3. After verification, pressing [ ] transfers execution to the foot-switch
1. Make sure that all LEDs light up.
check.
Measure current consumption and verify that it is 83 mA or less.
* Note:To skip measurement, advance to [ 2 ].
5. Foot SW check
2. Press the switches in the order shown in the following list.
Verify that the LED shown in the list goes dark when the switch is 1. Verify that [F1] is displayed on the 7-segment display.
pressed. Note: When no CTL (control) pedal is inserted, [Ft] is displayed.
Verify that a click is felt when the switch is pressed. 2. Depress the CTL1 (Tip) side and verify that the display changes to [F2].
When all switches have been pressed and all LEDs have gone dark,
3. Depress the CTL2 (Ring) side.
operation automatically advances to the VR check.
4. When operation is correct, execution is automatically transferred to the
D/A check.
11
May, 2007 ME-20
6. D/A Check 10. Verify that the waveform from the OUTPUT L/R jacks is muted.
fig.da-check-3.eps
1. Insert plugs into the OUTPUT L & R and PHONES jacks.
2. Set the oscilloscope to Ch1: 0.2 V/div, Ch2: 0.2 V/div, and time: 500 us/
div, and adjust the settings to monitor (verify) the output from the
PHONES jack on the oscilloscope.
5. Verify that the peak value of the PHONES waveform is 370 to 440 mVp-p.
fig.da-check-1.eps
13. Verify that the peak value of the OUTPUT L/R waveform is 370 to 440
mVp-p.
Note: Perform verification of the waveform with the plug remaining
inserted into the PHONES jack.
fig.da-check-4.eps
8. Verify that the waveform output from the PHONES jack is muted.
fig.da-check-2.eps
9. Change the input to the oscilloscope from PHONES to OUTPUT L/R and
make the settings to enable monitoring (verification) of the waveform on
the oscilloscope.
Note: Because the waveform may not be displayed correctly when
nothing is connected to the PHONES jack, insert a shielded cord or jack
adapter plug into the jack.
12
May, 2007 ME-20
16. Insert a plug into OUTPUT R and detach the plug connected to the 7. Verify that the peak value of the OUTPUT L/R waveform is 370 to 440
PHONES jack. mVp-p.
fig.aux-check.eps
17. Verify that the OUTPUT L/R waveform changes as shown below.
fig.da-check-6.eps
3. Press [ ].
13
May, 2007 ME-20
* Note: Never execute the following operations unless necessary. 11. Model Identification Check
1. Verify that [Gt] is displayed on the 7-segment display.
9. Factory Reset Note: Make sure the LOW (left) side of the TUNER LED is lighted at this time.
Note: When you are continuing operations from the previous page, start
execution at [3].
2. While holding down [DELAY] and [EQ], insert a plug into the INPUT
jack to power up the unit.
Note: Continue to hold down [DELAY] and [EQ] until [FA] is displayed.
4. Press [WRITE].
[FA.] (with a flashing dot) appears on the 7-segment display, and the unit goes
into standby for the factory reset.
6. All segments on the 7-segment display begin to flash, and the factory
reset is executed.
Note: Never switch off the power while the 7-segment display is flashing.
7. After the factory reset ends, [Pd] appears on the 7-segment display for
approximately 2 seconds, and then operation is transferred to adjustment
of the EXP (expression) pedal. 4. Press [ ].
* Note: [Pd] is an abbreviation of “pedal.” [Ed] is displayed on the 7-segment display.
2. While holding down [EQ] and [EZ EDIT], insert a plug into the INPUT
jack to power up the unit.
Note: Continue to hold down [EQ] and [EZ EDIT] until one of the [1] to
[9] is displayed.
4. Press [EDIT/EXIT].
5. The 7-segment display shows [Pd] for 2 to 3 seconds, after which [UP] is
displayed.
10. Forcefully depress the expression pedal, and make sure the WAH LED
lights up.
11. Forcefully depress the expression pedal, and make sure the WAH LED
goes dark.
14
May, 2007 ME-20
Block Diagram
fig.blockdiagram.eps
Batt;
POWER SW
LR6 SizeAA*6
PSA-XXX Buffer
Q3
9V
200mA
LvShift/ LvShift/ MUTE
Pemh/
CODEC MIX Q1,Q2,
AFAD IC4 Demh/ IC1 Q4,Q5
IC3 IC2
Analog;+9V Analog;+3.3V
Q11 (for CODEC) PHONES_DET
IC7
Reset
Digital;+3.3V
Digital;+1.5V BatteryDet
(for DSP Core) ESC
IC10
EEP IC6
(512kb) IC9
EEP IC8 X'tal
(8kb)
15
May, 2007 ME-20
16
May, 2007 ME-20
17
May, 2007 ME-20
3
+ DA2 R2 TP2 D +3. 3
NIU 5.6K C2 R3 TP3 C3 TP4 R4 JK1
1
2 1 2 - 10/16 1K 10/16 1K HTJ-064-12I
AUX IN
1
TP5 TP6 1 2
3 1
1
L2 A TP7 C4 3 + 4
OUT L(MONO)
8
7
6
5
JK2 NIU R5 C5 22P IC1A L1 1
1
HTJ-035-23DBS 1K 10/16 NJM4556AM 1 Q1 NIU RA1
1
2 RN1441 R7 C6 10K
3 R132 100K NIU TP81 Pedal SW
1
2
3
4
1 R6 NIU
10K R9
1
100K A A SW_DATA11 1 2
L3 R8 C7 + SW1
A A A A TP82
NIU 1K 10/16 R12 SKQKABD010
C8 C9 R10 R11 10K TP8 PEDAL_3
1
0.001 0.001 22K 22K C10 R13 TP9 C11 TP70 R14 JK3 SW_DATA10 1 2
10/16 1K 10/16 1K HTJ-064-12I TP83 SW2
1
R15 C12 C13 2 SKQKABD010
3 1
1
A A A A 10K 0.0018 NIU 4 PEDAL_2
OUT R
1
TP71 R17 L4 1 SW_DATA9 1 2
5.6K 1 Q2 R16 NIU C14 SW3
+6.33dB 6 - RN1441 100K NIU SKQKABD010
Emfasis;f1, f2, g=8.841kHz, 1.339kHz, 16.39dB
1
+ R18 7 R133 PEDAL_1
A8V
2
DA3 Gain=-11.44dB 56K C15 5 + NIU C16 C17 C18
NIU 22P IC1B NIU NIU NIU D
1 2 NJM4556AM
R20 C19 A A A A A
INPUT 15K (MF) NIU C21 TP12
3
1
L6 A C23 TP14 R24 R19 100/16
JK4 NIU R25 C24 Q3 CODEC_+3.3 10/16 27K 10K R21 D
1
2
HTJ-064-12DS 10K (MF) ECPU1E105KB5 2SK880GR C25 R26 C26 TP16 R27 2 - 100K
1
2 3 0.0018 10K (MF) 10P 10 1 TP15 + R22 L5 D +3. 3
3
3 3 + 47(1/2W) FBMA-10-160808-601T
A8V Panel SW
1
1 TP17 1 TP18 C27 IC2A R28 1 Q4
1
8
7
6
5
8
7
6
5
A 1 0.1 10/16 0 JK5 SW13
8
R29 R30 56K (MF) 3 + TP20 A A HTJ-064-05A R121 R32 RA3 RA4 SKQKABD010
R33 TP21 1M R34 IC3A 1 R36 C33 5 10K 10K 10K 10K EZ_EDIT 1 2
- D +3. 3
10K (MF) 10K (MF) NJM2100M 10K 0.0018 C157 C20 C34 TP22 4 SW4
1
2
3
4
1
2
3
4
A C31 C32 10 0.1 100/16 2 TP84TP85 SKQKABD010
+
1
1
R40 0.1 47/16 IC1C 3 1 2 SS
1
R39 A 150K(MF) NJM4556AM D1 7 SW5
PHONES
1
10K (MF) R42 1SS352 R37 L7 8 SW_DATA12 SKQKABD010
3
A 56K 47(1/2W) FBMA-10-160808-601T 1 SW_DATA8 EDIT/EXIT 1 2
2
5
4
C40 A R41 1 Q5 SW6
A 10P 100K RN1441 TP86 TP87 SKQKABD010
VA
VD
1
C36 C37 INVERT_IN 2 15 C42 SW_DATA7 WRITE 1 2
2
47/16 0.1 R43 LIN LOUT NIU C41 SW7
A SW_DATA6
10K (MF) TP24C43 C44 TP25 R44 TP26 R112 100/16 A A C38 C39 SW_DATA5 SKQKABD010
2
6 - 10/16 10/16 27K 100 Q6 NIU NIU A SW_DATA4 BANK- 1 2
7 NON_INVERT_IN 1 16 6 - 1 2SA1586GR D SW8
OUT_MUTE
1
1
RIN ROUT
1
5 + R45 100 7 TP27 TP88 TP89 SKQKABD010
IC3B 9 8 5 + D +3. 3DA6 SW_DATA3 1 2 BANK+
SDOUT SDIN
3
NJM2100M SDTI SDTO IC2B NIU SW9
SW_DATA2
1
10 14 + NJM14558M 2 1 SW_DATA1 SKQKABD010
LRCK LRCK VCOM D +3. 3
11 R46 C45 SW_DATA0 EFX_4 1 2
+23.52dB MCK
12
MCLK 1M 10/16 D SW10
BCK
3
A8V BCLK
1
7 SKQKABD010
+ DEM1 C46 C47 R47 C144 C48 EFX_3
6 A 1 2
VSS
DEMO 0.1 TP28 R48 10K TP90 TP92 NIU NIU SW11
13 A
CODEC_PDN PDN 1/50 A8V 0 TP91 TP93 SKQKABD010
IC7 TP29 CODEC_+3.3
3
IC4 + EFX_2 1 2
1
S-812C33AY-T AK4552VT SW12
2 3 C57 C49 C51 C53 C55 SKQKABD010
1
IN OUT
8
IC5C IC5B TP30 NIU D +3. 3 NIU NIU NIU NIU D EFX_1
GND
R54 TP32 C59 TC7W04FK TC7W04FK R49 R50 R51 EEPROM Writer side:1-2short C50 C52 C54 C56
-
8
10K (MF) TP31 0.1 C60 6 2 3 5 10K 10K 10K D CN1 5-6 short NIU NIU NIU NIU D
1
1 0.1 + A2001WV2-6P
-
1
4
NC
1
2
3
4
5
6
C78 C79 A 0.1 D A D TC7W04FK 8 2 TP35 EEPROM 0.1 0.1
10K (MF) 10/16 0.1 VCC A1
1 7 1 Adress: 101000;Program 1011**;User
4
1
2
3
4
5
6
C63 C145 C62 A0 D +3. 3
for AK4556: A WP: H;Protect L;Nomal
1
1
1
0.1 10 0.1 5
IC3C CKS3-0 pin = LLHH(AD-HPF=OFF) D +3. 3 4
SDA
6 D A D A D
NJM2100M VSS SCL R131
A 7
WP 10
WP_PROG
8
A D IC6 D +3. 3
D +3. 3 D +3. 3 C64 HN58X24512FPIE L8
DA4 C65 IC5D 0.1 C66 FBMA-10-160808-601T D+1.5 TP94
BAV99W 0.1 TC7W04FK 100/16 ESC_3.3V Q7 Q8 Q9 Q10
4
2 1 D R53 RN2426 RN2426 RN2426 RN2426 LED2 LED4 LED6 LED8 LED10 LED12
2
DA5 R117 R129 NIU L9 L-323SRDT L-34HDSL L-34HDSL L-34HDSL L-34HDSL L-34HDSL
R58 R59 BAV99W D 10K 10K C67 0.1 FBMA-10-160808-601T D D LED_COM0 1 1 1 1 TUNER_H EFX_2 EFX_4 SS PEDAL_2 WAH
3
JK6 47K 47K 2 1 A D C68 0.1 C77 LED1 LED3 LED5 LED7 LED9 LED11
HTJ-064-12DS L10 C69 0.1 ESC_1.5V 100/16 C142 C150 L-323SRDT L-34HDSL L-34HDSL L-34HDSL L-34HDSL L-34HDSL
3
NIU D C82 3 C75 0.1 100/16 0.1 TP36 1 TUNER_L EFX_1 EFX_3 EZ_EDIT PEDAL_1 PEDAL_3
3
1
L11 4.7K 4.7K 0.1 5 C87 0.1 C88 0.1 LED_COM3
SDA SDA_USER
2
NIU A D 4 6 C89 0.1 C90 0.1
VSS SCL SCL_USER
1
R56 D2 7 C91 0.1 C92 0.1
CTL_2 WP WP_USER
15K (MF) 1SS352 C93 0.1 C94 0.1
2
1
1
1
R62 C156 R63 IC8 C95 0.1 C96 0.1
114
122
132
144
101
108
141
4.7K 0.1 4.7K C98 C99 HN58X2408FPIE TP95 TP96 TP97
17
26
34
49
61
82
96
36
41
55
72
D D
9
D 0.01 0.01 TP78 TP80
CN3 TP79
EVDD
EVDD
EVDD
EVDD
EVDD
EVDD
EVDD
EVDD
EVDD
EVDD
EVDD
EVDD
IVDD
IVDD
IVDD
IVDD
IVDD
IVDD
IVDD
53015-0210 R57 C97 D
A D D 6.8K (MF) 10/16 CN2 LED13
1 NIU D +3. 3 A-552SR_BW
1
2 1 79 121
2 1 SCL CS4/SD0/TRR0/P80
2
2 RESET# 80
SDA CS3/P63
68 SDA_USER
3 69
3 CS1/SPICS/P62
4 DDO
A9V A8V 4
5 DCK 102 14 13
R66 + + 5 DMS DCK DIG1 DIG2
6 103 124
MINISMDC050F FL1 TP73 Q11 TP74 6 DDI DMS A23/SYNC/TRS7/P97
D3 7 104 125
DP1
WQT04-60 2SC4738 7 DDI A22/TRS6/P96
SS14 8 DRST# 105 126
G1
G2
C1
D1
C2
D2
DP
A1
B1
E1
A2
B2
E2
F1
F2
SW_DATA[0-12]
AD3R3V 8 DDO A21/TRS5/P95
2 2 4 3 2 A4V 9 106 127
1
16
15
18
17
11
10
12
9
R77 TP44 + 10 A19/TRS3/P93
1 1 3 129
10K (MF) A18/TRS2/P92
5 D 84 130
1
AVDD2 A17/TRS1/P91
3
AVREFP A16/TRS0/P90
2
AD13/SPIDI/P55
D R65 93
AIN7 AD12/SPIDO/P54
57
R67 0 10 BATTERY 92 58
AIN6 AD11/BUCK/P53
8
7
6
5
8
7
6
5
C106 D5 C107 R68 0 MASTER_VR 91 59 R69 R70 R71 R72 R73 R74 R75 R76
47/16 UDZS TE-17 9.1B 47/16 R78 0 PRM3_VR AIN5 AD10/BULCK/P52 RA7 RA8 120 47 47 47 47 47 47 47
A 90 60
PRM2_VR AIN4 AD9/BUDO1/P51 270 270
4 5 89 63
PRM1_VR AIN3 AD8/P50
3 6 88
1
2
3
4
1
2
3
4
PRM0_VR AIN2
2 7 87 43
AIN1 AD7/P47
3
10 1 8 EXP_VR 86 44
TP45 AIN0 AD6/P46
2 45
VR2A RA9 D+1.5 AD5/P45
20 46
AD4/P44
LED_COM[0-3]
VR2B RV110F-40E1-15AB-B50K-005 0 134 47
1
1
PRM_4 AVDD1 AD3/P43
D 48
R81 C118 C119 AD2/P42
51
0 100/16 0.1 AD1/P41
A9V 52
L12 TP47 AD0/P40
133
+ NIU C112 C114 C116 C120 AGND1 TP48 TP49 TP50 TP51 TP52 TP53 TP54 TP77
1 1 1 1 1 1 1 1
0.01 0.01 0.01 16P D 64
1
ALE/P67
3
C111 C113 C115 C117 139 65
ESC
NIU 0.01 0.01 0.01 X1 XIN CRD/P66
66 1 1 1 1 1 1 1 1
CWR/P65
3
2
10 16.9344MHz 67
WAIT/P64 SCL_USER D +3. 3
R82 R83 2 Q12 Q13 Q14 Q15 Q16 Q17 Q18 Q22
2
3.3K (MF) 2.2K (MF) TP56 TP57 20 VR3A C121 140 RN1307 RN1307 RN1307 RN1307 RN1307 RN1307 RN1307 RN1307
18
1
INT2/SD1/TRR1/P81
TP58 1 1 TP59 68P 47K C122 D PRM_3
(OpenDrain) 78 LED_DATA0 D D D D D D D D
VCC
1
R87 R88 C125 R89 13 R90 TP61 + 135 22 R122 47 SW_DATA8 LED_DATA3
DTC1 TMC1 EA13/CRD/P10
LED_DATA[0-7]
47K (MF) 18K (MF) 68P 47K 12 56 Q19 D+1.5 136 24 LED_COM2 LED_DATA4
PVCC1 R84 TMC2 EA12/WAIT/P22
TP62 6 11 1 QS5U27 137 21 R123 47 SW_DATA9 LED_DATA7
1
EA8/CS3/P21
1
R91 TP63 4 8 1 TP64 2 BD45301G 0 D 29 LED_DATA7
47K R93 NON2 PVCC2 VR4A EA7/AD15/P37
9 20 5 4 81 31
10K (MF) R94 OUT2 C127 C128 VR4B RV110F-40E1-15AB-B50K-005 VDD VOUT RESET EA6/AD13/P35 TP98 TP100 TP102 TP104
19 33 LED_DATA3
1
SUB
R95 15K (MF) STB R98 10/16 0.1 PRM_2 C124 EA5/AD11/P33 TP99 TP101 TP103 TP105
1 D 3 1 39 LED_DATA1
47K (MF) SEL1 56 R119 1 GND ER EA4/AD9/P31
CTL_2 70 40 LED_DATA0
C130 R96 R97 10K (MF) C131 C132 27K C126 TXD1/P61 EA3/AD8/P30
2 CTL_1 71 38 LED_DATA2
2
RT RXD1/P60 EA2/AD10/P32
2
3
8
7
6
5
17 76 2 4 5 SW_DATA7
GND
22K (MF) C134 R105 C136 C137 ELL6SH151 TCLR/BUDO0/P73 ED6/P06 SW_DATA5 10K
2 4 2 7
0.001 27K (MF) 0.1 0.1 IC10 TP75 VR5A TP66 R99 ED5/P05
1 20 119 5 1 8 SW_DATA4
20
1
2
3
4
BD9851EFV VR5B RV110F-40E1-15AB-B50K-005 TP67 1K PWM/SD2/TRR2/P82 ED4/INT2/P04 SW_DATA3
6 4 5
1
EGND
EGND
EGND
EGND
EGND
EGND
EGND
EGND
EGND
EGND
EGND
NIU 1K IGND
IGND
IGND
IGND
IGND
IGND
10 3 3
D +3. 3 3 3
A D 2 2 2
2
2 2 C141 CN6
20 1 1
VR6B 1 1 0.1 NIU IC9
D D
1
1
10
18
27
35
50
62
83
97
115
123
37
42
73
100
109
1
1 138 ESC
C153 VR6A 2 (uPD800402GJ-211-UEN-A)
2 MIDI_OUT
0.1 RK11K1140(10KSB) 3
3 MIDI_IN
EXP_VR 4 R109 R110 D D
4 NIU NIU
18 19
May, 2007 ME-20
Error Messages
• “bt” Appears in the Display
Batteries are run down. Replace with new batteries.
20