(DSS-1) (CE-301-F)
Rawal Institute of Engineering and Technology Time: 2 hrs Max. Marks--50
1st Mid Term Examination, October 2017 Note: Question no: 1 is compulsory. Attempt any two questions from
B .Tech (Civil, 5th Sem) Q2, Q3 & Q4
(DSS-1) (CE-301-F) Q1 Answer the following questions: (10x1)
Time: 2 hrs Max. Marks--50 k) What is meant by pitch, edge distance & gauge distance?
Note: Question no: 1 is compulsory. Attempt any two questions from l) Explain types of bolted joint with sketches.
Q2, Q3 & Q4 m) What are advantages of bolted connections?
n) What are the advantages of HSFG bolts?
Q1 Answer the following questions: (10x1)
o) Write short notes on shear lag effects.
a) What is meant by pitch, edge distance & gauge distance? p) What is laterally supported beam?
b) Explain types of bolted joint with sketches. q) What are the various types of bolts used for structural purposes?
c) What are advantages of welded connections? r) What is prying action?
d) What are the advantages of HSFG bolts? s) What are main failure modes of beam?
e) Write short notes on shear lag effects. t) State the functions of lacing & battening?
f) What is laterally supported beam?
g) What are the various types of bolts used for structural purposes?
h) What is prying action? Q2 Attempt both questions: (2x10=20)
i) What are main failure modes of beam?
j) State the functions of lacing & battening. c) Design the Lap joint for the plates of sizes 100 × 16 mm and
100 × 10 mm thick connected so as to transmit a factored load
Q2 Attempt both questions: (2x10=20)
of 100 KN using single row of 16 mm diameter bolts of grade
a) Design the Lap joint for the plates of sizes 100 × 16 mm and 4.6 and plate of 410 grade. Draw the sketch of connection.
100 × 10 mm thick connected so as to transmit a factored load d) Two plates of 6 mm thick are connected by single bolted 4 mm
of 100 KN using single row of 16 mm diameter bolts of grade thick double cover butt joint using M20 bolts at 60 mm pitch;
4.6 and plate of 410 grade. Draw the sketch of connection. steel grade 410 MPa and bolts 4.6 grade; Calculate bolt
b) Two plates of 6 mm thick are connected by single bolted 4 mm efficiency.
thick double cover butt joint using M20 bolts at 60 mm pitch;
steel grade 410 MPa and bolts 4.6 grade; Calculate bolt Q3 Attempt both questions: (2x10=20)
efficiency.
a) A tie member of a roof truss consists of 2Nos of ISA
Roll No.…………….. 100x75x8mm. The angles are connected to either side of a
Rawal Institute of Engineering and Technology 10mm thick gusset plate and the member is subjected to a
1st Mid Term Examination, October 2017
B .Tech (Civil, 5th Sem)
working pull of 300KN. Design the welded connection. working pull of 300KN. Design the welded connection.
Assume the connections are made in the shop. c ͓ ͓=31 mm Assume the connections are made in the shop. c ͓ ͓=31 mm
b) Design a suitable longitudinal fillet weld to connect the plates d) Design a suitable longitudinal fillet weld to connect the plates
as shown in fig. below. The pull to be transmitted is equal to as shown in fig. below. The pull to be transmitted is equal to
the full strength of the small plate. Given the plates are 12mm the full strength of the small plate. Given the plates are 12mm
thick, grade of plates is Fe410 and welding is made in the thick, grade of plates is Fe410 and welding is made in the
factories. factories.