MATERIAL
Note
Rev
ITEM SIZE THK/ ENDS DESCRIPTION
RAT
PIPE ½" ¾" .065 PE OD TUBING, SEAMLESS, 316L SS, ASTM A270 GR TP316L, BRIGHT ANNEALED
OD, ID FINISH 20-25 RA
1” 2” .065 BW OD TUBING, WELDED, 316L SS, ASTM A270 GR TP316L, BRIGHT ANNEALED OD,
3” 4” .083 BW ID FINISH 20-25 RA
FITTINGS ½" ¾" Match BW ASTM A270 GR TP316L
1” 4” Pipe Ferrule ASTM A270 GR TP316L, FERRULE (TRI-CLAMP)
FLANGES ½" ¾" 150# FF/PE ASTM A182, GR F304L, FF, CLASS 150L
1” 6” 150# FF/BW ASTM A182, GR F304L, FF, CLASS 150
GASKETS ½" 6” 150# FF FULL FACE, COMPRESSED NON-ASBESTOS, 1/16" THICK, CLASS 150, GARLOCK
STYLE 3500
CLAMPS ½" 6” (A) HINGED TYPE, HEAVY DUTY, W/HAND TIGHTEND WING NUT, 304 SS,
HINGED FOR DESURE SERVICE, WITH ONE PIECE MOLDED VITON O-RING, TRI-
CLOVER # 13MHHM
(B) TWO PIECE BOLTED, HEAVY DUTY, HIGH PRES/TEMP, 304 SS, No 4 FINISH,
WITH ONE PIECE MOLDED VITON O-RING, TRI-CLOVER #13MHP
VALVES
BALL ½" ¾" 125# SW S11-2
1” 6” BW S11-2
GATE ½" 3" 150# THRD A1-1A
3” 12” 150# FLG A1-1Z
CHECK ½" 4" 150# BW S11-5B
A1-5W
GLOBE
PLUG
BTFLY 3" 12” 150# A1-7
GAUGE
NEEDLE
NOTES
1. Use only where specifically noted on P&ID's
2. Limited to maximum temperature of 250F
3. Limited to maximum temperature of 300F
4. Fitting wall thickness must be the same as the adjoining pipe, and shall not be beveled, and no taper bore is allowed
5. Use only where zero static conditions are required
6. Use only where smooth internal finish is NOT required
7. Use clamp type fitting or valve only where shown on P&ID
8. Autoclavable valves shall be capable of being oven sterilized
9. Valves over 2" are available on custom order
10. Diaphram valves are limited to temperature and pressure, valves in horizontal lines to be rotated for self draining. See
manufacturers recommendations
11. Installation to include orbital welder. Welded tubing shall be 100% boroscoped by vendor before delivery
12. Do not install strainers upstream of steam traps
1½" RT RT RT T S Sockolet
3" S S S S RT T
4" S S S S RT RT T
6" S S S S W RT RT T
8" S S S S W W RT RT T
10" S S S S W W W RT RT T
12" S S S S W W W RT RT RT T
14"
16"
18"
20"
24"
½" ¾" 1" 1½" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24"
BRANCH PIPE
TABLE NOTES:
1. Threadolets shall be allowed for installation of needle and gauge valves and for local high point
vent / local low point drain valve installation per project specifications.
2. Branch connections shall be in accordance with API RP 14E, except as modified by Technical
Requirements.
3. The terms weldolet, sockolet and threadolet are utilized as general terms for Bonney Forge fittings.
A proper fitting of equivalent design, or a similar product for the particular service or piping
arrangement shall be provided in accordance with MSS-SP-97.