S3100
FinePix S3500
SERVICE MANUAL
US/CA/EU/EG/GE/AS-Model
WARNING
THE COMPONENTS IDENTIFIED BY THE MARK “ ” ON THE SCHEMATIC
DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR SAFETY.
PLEASE REPLACE ONLY BY THE COMPONENTS SPECIFIED ON THE SCHEMATIC
DIAGRAM AND IN THE PARTS LIST.
IF YOU USE PARTS NOT SPECIFIED, IT MAY RESULT IN A FIRE AND AN
ELECTRICAL SHOCK.
Ref.No.:ZM00552-101
FUJI PHOTO FILM CO., LTD. Printed in Japan 2005.10
Fine Pix S3100/S3500 SERVICE MANUAL
SAFETY CHECK-OUT
After correcting the original problem, perform the following
safety check before return the product to the costomer.
1. Check the area of your repair for unsoldered or poorly 6. Make leakage - current measurements to determine
sol dered connections. Check the entire board sur- that exposed parts are acceptably insulated from the
face for solder splasher and bridges. supply circuit before returning the product to the cus-
tomer.
2. Check the interboard wiring to ensure that no wires
are “pinched” or contact high-wattage resistors. 7. CAUTION: FOR CONTINUED PRO-
TECTION AGAINST FIRE HAZARD,
REPLACE ONLY WITH SAME TYPE
3. Look for unauthorized replacement parts, particuarly 2.5 AMPERES 125V FUSE.
tran sistors, that were installed during a previous re-
pair. Point them out to the customer and recommend RISK OF FIRE- ATTENTION: AFIN D'ASSURER
2.5A 125V REPLACE FUSE
their replacement. AS MARKED UNEPROTECTION PERMANENTE
2.5A 125V
CONTRE LES RISQUES D'INCENDIE,
REMPLACER UNIQUEMENT PAR UN
4. Look for parts which, though functioning, show ob- FUSIBLE DE MEME, TYPE 2.5 AM-
vious signs of deterioration. Point them out to the PERES, 125 VOLTS.
customer and recommend their replacement.
8.
WARNING! WARNING:
5. Check the B + voltage to see it is at the values speci- HIGH VOLTAGE TO REDUCE THE ELECTRIC SHOCK,
fied. BE CAREFUL TO TOUCH THE PARTS.
2
Fine Pix S3100/S3500 SERVICE MANUAL
TABLE OF CONTENTS
1. General ............................................................ 4 3-7-10. VCON Block Circuit ................................... 35
1-1. Product specification ............................................... 4 3-7-11. RSW Block Circuit ..................................... 35
1-2. Explanation of Terms ............................................... 6
4. Adjustment .................................................... 36
1-3. Names of External Components .............................. 7
4-1. Important point Adjustment when Replacing Major
2. Disassembly .................................................... 8 Parts ...................................................................... 36
2-1. Names of Internal Parts ........................................... 8 4-2. Measuring Instruments Used ................................. 36
2-2. How to Disassemble the CABI R ASSY .................. 9 4-3. Use Jig list ............................................................. 36
2-3. Removing LCD ASSY / LCD FRAME .................... 10 4-4. Calibration method of pattern box ......................... 37
2-4. Removing EVF CONST ......................................... 11 4-5. Adjusting soft installation ....................................... 37
2-5. Removing MAIN PWB ASSY ................................. 11 4-5-1. Various downloading software
2-6. Removing BATTERY HOLDER ASSY ................... 11 decompressions, preservation methods,
2-7. Removing DCST PWB ASSY ................................ 12 and notes .................................................. 37
2-8. Removing LENS CONST ...................................... 12 4-5-2. Installation of DSC jig driver ...................... 38
2-9. Removing STROBE CONST/ST TOP ................... 13 4-5-3. Adjusting soft initiation method ................. 38
2-10. Removing MSW PWB ASSY and 4-6. Initial Settings of the Adjustment Software ........... 39
RSW PWB ASSY .................................................. 14 4-7. Starting the Adjustment Software .......................... 42
2-11. Removing KEY PWB ASSY ................................... 14 4-8. [F5] : CAMERA Adjustment ................................... 45
2-12. Disassembly of LENS CONST .............................. 15 4-9. [F4] CCD Defect Correction Adjustment ................ 48
2-13. Location of Sheet parts .......................................... 16 4-10. [F6] : AF Adjustment .............................................. 50
2-13-1. CCD EMI SHEET (FZ06017-100) ............. 16 4-11. [F7] : Flash Adjustment .......................................... 52
2-13-2. GASKET USB (BB18395-100) .................. 16 4-12. [F1] : Battery Voltage Adjustment .......................... 54
2-13-3. LCD-EMI SHEET (FZ6000-100) ............... 16 4-13. [F11] : Video Adjustment ........................................ 58
2-13-4. LENS-EMI SHEET (FZ06018-100) ........... 17 4-14. [F3] : LCD Adjustment ........................................... 60
2-13-5. EMI SHEET AF (FZ05587-100) ................ 17 4-15. [F8] : Firmware Download ..................................... 62
4-16. [F12] : End Setting ................................................. 64
3. Schematics .................................................... 19
3-1. Cautions ................................................................ 19
5. Inspection ...................................................... 68
3-2. Names and Functions of Basic Blocks .................. 19 5-1. Required Measuring Equipment ............................ 68
3-3. Explanation of Functions of Important Blocks ....... 20 5-2. Connection of Measuring Equipment .................... 68
3-4. Block Diagram ....................................................... 21 5-3. Inspection and Factory Settings ............................ 68
3-5. Overall ................................................................... 22
6. Parts list ......................................................... 70
3-6. Mounted Parts Diagrams ....................................... 23
6-1. Packing and Accessoris ........................................ 70
3-6-1. MAIN PWB ASSY Component Location ... 23
6-1-1. FinePix S3100 (US model) ....................... 70
3-6-2. DCDC PWB ASSY Component Location .. 24
6-1-2. FinePix S3100 (CA model) ........................ 71
3-6-3. CCD PWB CONST Component Location . 25
6-1-3. FinePix S3500 (EU model) ....................... 72
3-6-4. MSW PWB UNIT Component Location .... 25
6-1-4. FinePix S3500 (EG model) ....................... 73
3-6-5. RSW PWB UNIT Component Location ..... 25
6-1-5. FinePix S3500 (GE model) ....................... 74
3-6-6. VCON PWB UNIT Component Location ... 26
6-1-6. FinePix S3500 (AS model) ........................ 75
3-6-7. KEY PWB UNIT Component Location ...... 26
6-2. Cabinet F block ..................................................... 76
3-7. Circuit Diagrams .................................................... 27
6-2-1. FinePix S3100(US/CA model) ................... 76
3-7-1. DCDC Block Circuit ................................... 27
6-2-2. FinePix S3500(EU/EG/GE/AS model) ...... 77
3-7-2. PROCESS Block Circuit ........................... 28
6-3. Inner block ............................................................. 78
3-7-3. CAM Block Circuit ..................................... 29
6-4. Cabinet R block ..................................................... 79
3-7-4. IPS_STROBE Block Circuit ...................... 30
6-5. Electrical parts ....................................................... 80
3-7-5. MOTOR Block Circuit ................................ 31
3-7-6. LCD Block Circuit ...................................... 32
7. Appendix ....................................................... 81
3-7-7. CCD Block Circuit ..................................... 33
7-1. Version display function ......................................... 81
3-7-8. MSW Block Circuit .................................... 34
7-2. List of Related Technical Updates Issued .............. 82
3-7-9. KSW Block Circuit ..................................... 34
3
1.General Fine Pix S3100/S3500 SERVICE MANUAL
1.General
1-1.Product specification
System
Model Digital camera FinePix S3100 / FinePix S3500
Effective pixels 4.0 million pixels
CCD 1/2.7 inch square pixel CCD Number of total pixels: 4.23 million pixels
Number of recorded pixels Still image: 2272 × 1704 pixels/1600 × 1200 pixels/1280 × 960 pixels/
640 × 480 pixels ( / / / )
Movie: 320 × 240 pixels (10 frames per second without sound)
160 × 120 pixels (10 frames per second without sound)
Storage media xD-Picture Card (16/32/64/128/256/512 MB)
File format Still image: JPEG (Exif ver. 2.2)
* Design rule for Camera File System compliant DPOF compatible
Movie: AVI format, Motion JPEG
Lens Fujinon 6 × optical zoom lens, F2.8-F3.0
Aperture F2.8 to F3.0 (automatically selected)
Focal length f=6.0 mm to 36 mm (Equivalent to 39 mm to 234 mm on a 35 mm camera)
Focal range Normal: Approx. 0.8 m (2.6 ft.) to infinity
Macro: Approx. 0.1 m (3.9 in.) to 0.8 m (2.6 ft.)
Shutter speed 2 sec. to 1/1500 sec. (combined with mechanical shutter)
Focus TTL contrast-type, Auto focus
Sensitivity Equivalent to ISO 100 (automatically set between ISO 64 - 250 depend on the
shooting mode and subject.)
Photometry TTL 64-zones metering
Exposure control Program AE
Exposure compensation -2.1 EV to +1.5 EV in 0.3-step increments (in Manual mode)
White balance Auto ( ), Scene position ( ) Manual modes, 7 positions can be selected
Viewfinder 0.33 inches 110,000 pixels electronic viewfinder
NTSC Approx. 88% coverage PAL Approx. 86% coverage
LCD monitor 1.5 inches, 60,000 pixels amorphous silicon TFT,
NTSC: Approx. 87% coverage, PAL: Approx. 85% coverage
Flash type Auto flash using flash control sensor
Effective range:
Wide-angle: Approx. 0.8 m to 3.5 m (2.6 ft. to 11.5 ft.)
(Approx. 0.3 m to 0.8 m (1.0 ft. to 2.6 ft.): Macro)
Telephoto: Approx. 0.8 m to 3.5 m (2.6 ft. to 11.5 ft.)
Flash modes: Auto, Red-Eye Reduction, Forced Flash, Suppressed Flash, Slow
Synchro*, Red-Eye Reduction + Slow Synchro* * In Manual mode
Self-Timer 10 sec.
Video output NTSC/PAL selectable
Input/Output Terminals
Video output socket 2.5 mm dia. jack
(USB) socket For file transfer to a computer
DC Input Socket for specified AC power adapter AC-5VH/AC-5VHS (sold separately)
Standard number of available frames/recording time per xD-Picture Card
The number of available frames, recording time or file size varies slightly depending on the subjects photographed. Note also
that the difference between standard number of frames and the actual number of frames is greater for
xD-Picture Cards with higher capacities.
Quality Setting F N Movie Movie
Number of recorded pixels 2272 1704 1600 1200 1280 960 640 480 320 240 160 120
Image Data Size 1.9 MB 960 KB 620 KB 460 KB 125 KB
DPC-16 (16 MB) 8 16 25 33 122 Approx. 98 sec. Approx. 5.6 min.
DPC-32 (32 MB) 16 32 50 68 247 Approx. 199 sec. Approx. 11.3 min.
DPC-64 (64 MB) 33 66 101 137 497 Approx. 6.6 min. Approx. 22.7 min.
DPC-128 (128 MB) 66 132 204 275 997 Approx. 13.3 min. Approx. 45.5 min.
DPC-256 (256 MB) 134 266 409 550 1997 Approx. 26.7 min. Approx. 91.2 min.
DPC-512 (512 MB) 268 532 818 1101 3993 Approx. 53.5 min. Approx. 182.5 min.
4
Fine Pix S3100/S3500 SERVICE MANUAL 1.General
Power Supply and Others
Power supply Use one of the following:
• 4×AA-size alkaline batteries
• 4×AA-size Ni-MH (Nickel-Metal Hydride) batteries (sold separately)
• AC Power Adapter AC-5VH/AC-5VHS (sold separately)
Guide to the number Battery Type
of available frames Alkaline batteries Ni-MH batteries (2300mAH)
for battery operation
Approx. 300 frames Approx. 500 frames
According to the Camera & Imaging Products Association (CIPA) standards*:
When using alkaline batteries, use the batteries supplied with the camera. When
using Ni-MH batteries, use Fujifilm Rechargeble Battery.
The storage media should be xD-Picture Card.
• Note: Because the number of available shots varies depending on the capacity of
alkaline batteries or the level of charge in Ni-MH batteries, the figures
shown here for the number of available shots using batteries are not guar-
anteed.
The number of available shots will also decline at low temperatures.
* “CIPA DC-002-2003 ‘Standard Procedure for Measuring Digital Still Camera Bat-
tery Consumption’ ” (extract)
Pictures shall be taken at a temperature of 23 oC, with the LCD monitor turned on,
the zoom moved from full wide-angle to full telephoto (or vice-versa) and back
again to its original position every 30 seconds, the flash used at full power every
second shot and the camera turned off and then on again once every 10 shots.
Conditions for use Temperature: 0oC to +40oC (+32oF to +104oF); 80% humidity or less (no condensation)
Camera dimensions 99.7 mm × 77.3 mm × 69.3 mm/3.9 in. × 3.0 in. × 2.7 in.
(W/H/D) (not including accessories and attachments)
Camera mass (weight) Approx. 285 g/10.1 oz.
(not including accessories, batteries, xD-Picture Card and Adapter Ring)
Weight for photography Approx. 410 g/14.5 oz. (including batteries and xD-Picture Card)
Accessories z LR6 AA-size alkaline batteries (4)
z 16MB, xD-Picture Card (1) Included with: Anti-static case (1)
z Shoulder strap (1)
z Video cable (1) (plug (2.5 mm dia. ) to pin-plug) Approx. 1.5 m (4.9 ft.)
z USB cable (1) z Lens cap (1) z Adapter ring (1)
z CD-ROM: Software for FinePix AX (1) z Owner’s Manual (1)
Optional Accessories z xD-Picture Card
DPC-16 (16 MB)/DPC-32 (32 MB)/DPC-64 (64 MB)/DPC-128 (128 MB)/
DPC-256 (256 MB)/DPC-512 (512 MB)
z AC Power Adapter AC-5VH/AC-5VHS z Fujifilm Rechargeable Battery 2HR-3UF
z Fujifilm Battery Charger with Battery BK-NH/BK-NH2 (With Euro type or UK type plug)
z Carrying Case SC-FX304
z Image Memory Card Reader DPC-R1
• Compatible with Windows 98/98 SE, Windows Me, Windows 2000 Profes-
sional, Windows XP or iMac, Mac OS 8.6 to 9.2.2, Mac OS X (10.1.2 to
10.2.2) and models that support USB as standard.
• Compatible with xD-Picture Cards of 16 MB to 512 MB, and SmartMedia of
3.3V, 4 MB to 128 MB.
z PC Card Adapter DPC-AD
• Compatible with xD-Picture Cards of 16 MB to 512 MB, and SmartMedia of
3.3V, 2 MB to 128 MB.
z CompactFlash Card Adapter DPC-CF
• Windows 95/98/98 SE/Me/2000 Professional/XP
• Mac OS 8.6 to 9.2/X (10.1.2 to 10.1.5)
z xD-Picture Card USB Drive DPC-UD1
• Compatible with xD-Picture Card of 16 MB to 512 MB
• Windows 98/98 SE/Me/2000 Professional/XP
• Mac OS 9.0 to 9.2/X (10.0.4 to 10.2.6)
5
1.General Fine Pix S3100/S3500 SERVICE MANUAL
1-2.Explanation of Terms
AF/AE Lock: On the FinePix S3100/FinePix S3500, pressing the shutter button down half way
locks the focus and exposure settings (AF and AE lock). If you want to focus on a
subject that is not centered in the frame or change the picture composition after the
exposure is set, you can obtain good results by changing the composition after the
AF and AE settings are locked.
Auto power save function: If the camera is not used in any way for 60 seconds, this function turns features
such as the LCD monitor off (sleep mode) to prevent battery depletion and the
waste of power when the AC power adapter is connected. If the camera is then left
unused for a further period, the Auto power save function turns the camera off. This
period can be set to 2 minutes or 5 minutes on this camera.
z The Auto power off function does not operate in PC mode, during automatic
playback, or if it is disabled during setup.
Deactivated batteries: Leaving an Ni-MH battery unused in storage for a long period may cause a rise in
the level of substances that inhibit current flow inside the battery and result in a
dormant battery. A battery in this state is referred to as deactivated.
Because current flow is inhibited in a deactivated Ni-MH battery, the battery’s origi-
nal level of performance cannot be achieved.
DPOF: Digital Print Order Format
DPOF is a format used for recording information on a storage media (image
memory card, etc.) that allows you to specify which of the frames shot using a
digital camera are to be printed and how many prints are made of each image.
EV: A number that denotes Exposure Value. The EV is determined by the brightness of
the subject and sensitivity (speed) of the film or CCD. The number is larger for
bright subjects and smaller for dark subjects. As the brightness of the subject
changes, a digital camera maintains the amount of light hitting the CCD at a con-
stant level by adjusting the aperture and shutter speed.
When the amount of light striking the CCD doubles, the EV increases by 1. Like-
wise, when the light is halved, the EV decreases by 1.
Frame rate (fps): The frame rate refers to the number of images (frames) that are photographed or
played back per second. For example, when 10 frames are continuously photo-
graphed in a 1-second interval, the frame rate is expressed as 10 fps.
For reference, TV images are displayed at 30 fps (NTSC).
JPEG : Joint Photographics Experts Group
A file format used for compressing and saving color images. The higher the compres-
sion rate, the greater the loss of quality in the decompressed (restored) image.
Memory effect: If an Ni-MH battery is repeatedly charged without first being fully discharged, its perfor-
mance may drop below its original level. This is referred to as the “memory effect”.
Motion JPEG: A type of AVI (Audio Video Interleave) file format that handles images and sound as
a single file. Images in the file are recorded in JPEG format. Motion JPEG can be
played back by QuickTime 3.0 or later.
PC Card: A generic term for cards that meet the PC Card Standard.
PC Card Standard: A standard for PC cards determined by the PCMCIA.
PCMCIA: Personal Computer Memory Card International Association (US).
Smear: A phenomenon specific to CCDs whereby white streaks appear on the image when
there is a very strong light source, such as the sun or reflected sunlight, in the
photography screen.
WAVE: A standard format used on Windows systems for saving audio data. WAVE files
have the “.WAV” file extension and the data can be saved in either compressed or
uncompressed format. Uncompressed recording is used on this camera.
WAVE files can be played back on a personal computer using the following software:
Windows: MediaPlayer
Macintosh: QuickTime Player
* QuickTime 3.0 or later
White Balance: Whatever the kind of the light, the human eye adapts to it so that a white object still
looks white. On the other hand, devices such as digital cameras see a white subject
as white by first adjusting the color balance to suit the color of the ambient light
around the subject. This adjustment is called matching the white balance.
Exif Print: Exif Print Format is a newly revised digital camera file format that contains a variety
of shooting information for optimal printing.
6
Fine Pix S3100/S3500 SERVICE MANUAL 1.General
1-3.Names of External Components
Mode dial
Power switch
Shutter button
Self-timer lamp
Strap mount
Flash
/ Macro button
/ Flash button
EVF / LCD
(monitor selector) Strap mount
button
7
2.Disassembly Fine Pix S3100/S3500 SERVICE MANUAL
2. Disassembly
2-1.Names of Internal Parts
EVF CONST
STROBE CONST
LCD CONST
MSW PWB ASSY
RSW PWB ASSY
LCD FRAME
LENS UNIT
8
Fine Pix S3100/S3500 SERVICE MANUAL 2.Disassembly
2-2.How to Disassemble the CABI R ASSY
Remove in the order indicated by circled numbers.
4 3
<Step2>
(5) Remove connector (CN203).
9
2.Disassembly Fine Pix S3100/S3500 SERVICE MANUAL
1
(1) Remove two screws.
(2) Remove the hook of LCD FRAME (two places), and raise
2
LCD ASSY in the direction of the arrow.
<Step2>
3
1
(1) Remove CN452.
(2) Remove CN451.
(3) Remove EVF CONST in the direction of the arrow. 2
10
Fine Pix S3100/S3500 SERVICE MANUAL 2.Disassembly
2-5.Removing MAIN PWB ASSY
Remove in the order indicated by circled numbers.
<Step1>
1
(1) Remove CN201 CN202, CN281, CN301and CN101.
(2) Remove MAIN PWB ASSY in the direction of the arrow 2
while removing the connector in A part. A
1
1
(note) <Step2>
Make the power lever a turning off mode.
(1) Raise BATTERY HOLDER ASSY in the direction of the 1
arrow.
(2) Remove CN601.
2
11
2.Disassembly Fine Pix S3100/S3500 SERVICE MANUAL
<Step1>
(1) Remove two screws.
(2) Remove CN701, CN751. 2
<Step2>
(4) Remove FPC of LENS CONST in the direction of the
arrow.
12
Fine Pix S3100/S3500 SERVICE MANUAL 2.Disassembly
2-9.Removing STROBE CONST/ST TOP
Remove in the order indicated by circled numbers.
<Step1>
1
(1) Remove one screw. 2
(2) Remove STRAP BASE(R) in the direction of the arrow.
<Step2>
<Step3>
10
(6) Pull out two ST SHAFT.
(7) STOROBE must improve in pop-up.
(8) Remove two screws. 7
13
2.Disassembly Fine Pix S3100/S3500 SERVICE MANUAL
A RSW PWB
14
Fine Pix S3100/S3500 SERVICE MANUAL 2.Disassembly
2-12.Disassembly of LENS CONST
15
2.Disassembly Fine Pix S3100/S3500 SERVICE MANUAL
16
Fine Pix S3100/S3500 SERVICE MANUAL 2.Disassembly
2-13-4.LENS-EMI SHEET (FZ06018-100)
B A
17
2.Disassembly Fine Pix S3100/S3500 SERVICE MANUAL
MEMO
18
Fine Pix S3100/S3500 SERVICE MANUAL 3.Schematics
3.Schematics
3-1.Cautions
Precautions in parts replacement
Do not reuse detached electronic components. Use only new components.
The negative side of tantalum capacitors is weak against heat. Handle with care.
With the exception of Chemical capacitor and tantalum capacitors, the voltage of capacitors of a 50V or lower withstand voltage
is not labeled.
Unless specified, electronic component resistance is 1/16W.
K = 1000 , M = 1000 K
19
3.Schematics Fine Pix S3100/S3500 SERVICE MANUAL
20
Fine Pix S3100/3500 SERVICE MANUAL 3.Schematics
3-4.Block Diagram
Block Diagram
CCD_OUT
XCS2 3.3V Operation IC205 JTAG
6gZOOM LENS BA-CCD RENESAS AFE
D+,D-,VBUS
Fujinon ICX488DQF HD49334ANPED USB USB
3.3V Operation
IBFC
O.LPS
AUTO
WIDE/TELE 1/2.7inch Drv. CCD DATA[9-0]
RECC xD
g2 CDS PGA A/D C
Variable 4million pixels CAM ON CCDIF CARD
CAM 3.3V
AFE CS
Slot
MEDIA (20PIN)
CAM SCK
YCPRO TFDC
SHD,SHP,CPOB
LCD EVR
PBLK,ADCLK LCD CS
V1,V2,V3A,V3B,V4,V5A,V5B,V6 Drv. OFD CONT
FM A,FM B<FM/A,FM/B
SHUTOUT1,SHUTOUT2
ENCD LCDCLK
LCD
SML IM1-,SML IM2+
MID IM1-,MID IM2+
OCONT
CGEN
LCD HD
LCD VD
1.5inch 62MPixel
ZPOSI C,ZPI C,
RTG
V_Drv. XOFD,XVCLK
FF1170 TG CS DEBUG I/F
FPI C
3.3V Operation
MD2174 IC101 LM LED Back Light
AVD Audio(Serial)
Motor Drv.
H1,H2 H AHD EVF RESET
M50239HP RG DCLK A/D Audio(A/D) EVF DRV ON EVF- Driver EVF(SANYO)
CPU Core MFT LC15005 TBMV
0.33inch 11MPixel
IC451
IC301 SHT PLS(CLS)
SHT MNS(CLS) VRESET EVF BL ON
IC102 JPEG ICU LED Back Light
STRB_SY
X2 SO,X2 SC I- cache ??k
CTL SIO VCON PWB
MTR CS
AV OUT
IM A,IM B,IM C,FM A,FM B,FM C
BUS Cont. DAC
VIDEO ON
VIDEO VCOM
SDRAMC DRIVER
F HP,Z HP,ZPLS DMAC PORT AV_JACK
CCD ON
STROBE CONST IPS IC751 EVF 8.5V ON
POWER_ON_IC
FF1174
IPS ACT
STRB-XE STROBO_BLK IPS SCK Door- SW
STROBO IPS SO
CTL IPS SI
P-TR IPS CS
BAT V
LED CTL PWR SW
STROBO SW DRIVER
g3
STROBO_POPUP BATT Internal Internal KSW PWB
CLKC I/O Buffer eDRAMA
BACKUP PW SW 48MHz eDRAMB
EV3 Key SW
RTC POWER ON
OE CK48 OE RESET LED
CLKOUT
VCLKIN
RESET SEL DRIVER
g2
32.768kHz
DATA BUS[0-15] ADDRESS BUS[20-1] LED_Green/LED_Red
Right/Left/Down/Up
27/36 NT/PAL OK/BACK/DISP/EVF/LCD
DC/DC Flash ROM
IC204 IC203 2M
DC/DC IC M28W320ECT70ZBF2 MSW PWB
PWCTL
AN30212A_VB SELECTOR
5ch IC202 Mode SW
IC501 CCD_CLK LED
DRIVER
AD 5V PWCTL g1
DC IN FUSE FUSE
MOT_3.3V
CAM 3.3V
5V LED_Stand-by
3.3V ON
D 3.3V MODE1
BATT MODE2
FUSE
AAg4 CCD-7.5V POWER_ON
CCD 15V
PLAY/CAM
D_8.5V
D 5.6V
Release SW
STRB UNREG S1/S2
DCST PWB MAIN PWB
RSW PWB
21
3.Schematics Fine Pix S3100/3500 SERVICE MANUAL
3-5.Overall
STH_EVF
XSTH_EVF
VCOM
VC1
VC2
Vgoff_L
VC4
AVDD1
FB(LED_C)
DD4
DD3
DD2
DD1
DD0
COM
CKV1
CKV2
SEL0
XDSG
CKH2
CKH1
ISCI
DSG
VGH
Vgoff_H
VCC
AGND
AVDD
HSYNC
VSYNC
GBR
VCC
GND
DSD
CSH
VDD
FRP
V
LED_A
DCLK
CS
ISDA
STV
V
ENB
CSV
VSS
EVF_BL
GND 24 1 GND GND 1
23 2 VOUT CARD 2
22 3 GND R/B 3
RE 4
CCD_PWB
xD_CARD_CN
CCD_+15V 21 4 CCD_+15V
GND 20 5 GND
FH12_33S 0.5SH 22FLT_SM1 CE 5
SM02B_SRSS_TB
PES018_20C31106
RG 19 6 RG CLE 6
H2 7 H2 ALE 7
H1 17 8 H1
LCD BLK EVF BLK WE 8
GND 16 9 GND WP 9
GND 10
CAM BLK
CSUB 15 10 CSUB
SUB 14 11 SUB D0 11
VHLD 13 12 VHLD D1 12
VST 12 13 VST D2 13
V1 11 14 V1 D3 14
V2 10 15 V2 D4 15
D5 16
FH12_24S_0.5SH
V3A 9 16 V3A
V3B 8 17 V3B D6 17
V4 7 18 V4 D7 18
V5A 6 19 V5A VCC 19
V5B 5 20 V5B VCC 20
V6 4 21 V6
VL 3 22 VL
USB_CN
GND 2
GND 1
23
24
GND
GND
MAIN PWB 59110_0428
VCON
1 ZPI_C PROCESS BLK AV_JACK
2 ZPI_E HSJ1650_010025
3 3V VBS 1 3 VBS
4 SHUTOUT1
5 SHUTOUT2
VIDEO BLK GND 2 2
DET 3 1
LENZ UNIT
6 MID IM1-
SM03B_SRSS_TB
MOTOR BLK
7 MID IM2+
MOTOR_FPC
20FLT_SM1
8 SML IM1-
POP_SW
9 SML IM2+
06FLT_SM1
10 FM/A SPEAKER+ 1 ? ?
POP_FFC
11 FM/B SPEAKER+ 2 ? ?
???
12 FM A STRB_POP 3 ? ?
13 FM B GND 4 ? ?
14 FPI_C SPEAKER- 5 ? ?
15 FPI_E SPEAKER- 6 ? ?
16 3V 9831S_50Y930 06FLT_SM1 12FLT_SM1
17 ZPOSI_C
EVF8.5VON
OK/B/D/E_L
CAM_3.3V
CAM_3.3V
MOT_3.3V
MOT_3.3V
STRB_SY
18 ZPOSI_E
CCD_15V
CCD_15V
PWR_SW
IPS_SCK
CCD_ON
IPS_ACT
X2_3.3V
PW_SW
PW_SW
LED_ST
LED_ST
IPS_SO
IPS_CS
MODE2
MODE1
RESET
D_3.3V
D_3.3V
D_3.3V
D_3.3V
D_8.5V
D_8.5V
D_5.6V
D_5.6V
D_5.6V
LED_G
LED_G
19 ZM1+
LED_R
LED_R
AD_5V
AD_5V
IPS_SI
BAT_V
CCD_
CCD_
RLDU
A3.3V
A3.3V
VREF
PLAY
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
N.C.
N.C.
N.C.
20 ZM2-
EV3
EV3
S2
S1
5V
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 1 3 4 5 6 2 3 4 5 6 7 8 9 10 11 12
B to B CN KSW_FFC MSW_FFC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 40 41 42 43 44 45 46 47 49 50 1 2 3 4 5 6 2 4 5 6 8 9 10 11 12
VREF
LED_ST
IPS_ACT
RESET
N.C.
LED_G
IPS_SI
IPS_SO
EV3
N.C.
GND
GND
GND
GND
GND
GND
CCD_ON
LED_R
GND
GND
GND
GND
D_3.3V
D_3.3V
D_3.3V
CAM_3.3V
D_3.3V
CAM_3.3V
MOT_3.3V
CCD_15V
MOT_3.3V
CCD_15V
D_8.5V
D_8.5V
D_5.6V
V
D_5.6V
V
D_5.6V
AD_5V
AD_5V
EVF8.5VON
IPS_CS
IPS_SCK
PW_SW
BAT_V
PWR_SW
X2_3.3V
STRB_SY
LED_ST
KEY1
KEY2
LED_G
EV3
S2
S1
MODE2
MODE1
LED_R
GND
GND
GND
A3.3V
PW_SW
PLAY
A3.3V
5V
CCD_
CCD_
6FLZ_SM1_TB
DCST PWB
6FHJ_SM1_TB
DC CN PhTr_CN KSW MSW GND 1 1 GND
RSW_FFC
GND 2 2 GND
HEC3654_012010 53261_0290
POWER ON BLK STRB BLK PWB S2
S1
3
4
3
4
S2
22
Fine Pix S3100/S3500 SERVICE MANUAL 3.Schematics
3-6.Mounted Parts Diagrams
3-6-1.MAIN PWB ASSY Component Location
CN203
CN201
CN451
SW201
CN301
CN204
CN401
SIDE-A
CN206
CN207
CN101 CN205
SIDE-B
23
3.Schematics Fine Pix S3100/S3500 SERVICE MANUAL
CN701
CN751
F605
CN602
F603
F604
BT751
CN601
F602
SIDE_A
F501
J601
SIDE_B
24
Fine Pix S3100/S3500 SERVICE MANUAL 3.Schematics
3-6-3.CCD PWB CONST Component Location
CN1
IC1
SIDE_A SIDE_B
SW903
SW904
SW902
CN902
SW901
CN901
SIDE-A SIDE-B
SIDE-A SIDE-B
25
3.Schematics Fine Pix S3100/S3500 SERVICE MANUAL
SIDE-A SIDE-B
SIDE-A
SIDE-B
26
Fine Pix S3100/3500 SERVICE MANUAL 3.Schematics
3-7.Circuit Diagrams
3-7-1.DCDC Block Circuit
27
3.Schematics Fine Pix S3100/3500 SERVICE MANUAL
28
Fine Pix S3100/S3500 SERVICE MANUAL 3.Schematics
3-7-3.CAM Block Circuit
29
3.Schematics Fine Pix S3100/S3500 SERVICE MANUAL
30
Fine Pix S3100/S3500 SERVICE MANUAL 3.Schematics
3-7-5.MOTOR Block Circuit
31
3.Schematics Fine Pix S3100/S3500 SERVICE MANUAL
32
Fine Pix S3100/S3500 SERVICE MANUAL 3.Schematics
3-7-7.CCD Block Circuit
33
3.Schematics Fine Pix S3100/S3500 SERVICE MANUAL
34
Fine Pix S3100/S3500 SERVICE MANUAL 3.Schematics
3-7-10.VCON Block Circuit
35
4.Adjustment Fine Pix S3100/S3500 SERVICE MANUAL
4.Adjustment
4-1.Important point Adjustment when Replacing Major Parts
Adjust the item shown by { in the table below at the part replacement of MAIN PWB ASSY, DCST PWB ASSY,
LENS CONST, and LCD ASSY. (Other part replacements need not be adjusted. )
Replacing parts
Adjustment item MAIN PWB LENS CONST DCST PWB LCD CONST
1 CAMERA adjustment { {
2 CCD Defect adjustment { {
3 AF/ZOOM adjustment { {
4 Flash adjustment { { {
5 Battery adjustment { { {
6 Video adjustment { {
7 LCD adjustment { { {
8 Firmware download Do not use it until there is an instruction.
9 End setting Do the end setting when you end the adjustment software when you set the camera to the Jig mode.
36
Fine Pix S3100/S3500 SERVICE MANUAL 4.Adjustment
4-4.Calibration method of pattern box
< Use the pattern box for CAMERA adjustment >
Turn on the power supply in the pattern box.
Afterwards, wait for about ten minutes so that the source of Pattern BOX
light may stabilize. (All white)
(1) Brightness:
160±5cd/m2 (with LB140 filter)
No chart, center of pattern box
Minolta brightness meter LS-110 or equivalent
* Calibration method LB140
Place the filter (LB140) against the pattern box. With the
filter (LB140) in contact with the brightness meter, adjust
the pattern box brightness to 160±5cd/m2. <Fig. 4-4-1> Calibration method of pattern box
(2) Color temperature:aa
6100±50 K (with LB140 filter)
No chart, center of pattern box
Minolta color meter IIIF or equivalent
* Calibration method
Place the filter (LB140) against the pattern box. With the
filter (LB140) in contact with the color temperature meter,
adjust the pattern box color temperature to 6100 ± 50 K.
method
<Step1>
Download compressed PC adjustment software (ZJ00807-
100.ZIP) from Web server (http://fujifilm-di.intranets.com/)
<Fig. 4-5-1>.
(Note) My Computer
* Specify the preservation drive for C drive if it is 3.5inch FD(A:)
decompression software which can specify the
preservation drive.
(C:)
* Similarly, defrost without making a new folder if it is ZJ00807-100
decompression software which can be defrosted without
FinePixS3100_3500_W
making a new folder.
* Defrost simply if the decompression software which you
have cannot specify the drive specification and the folder
making. <Fig. 4-5-2>
37
4.Adjustment Fine Pix S3100/S3500 SERVICE MANUAL
<Step3>
The folder named ZJ00807-100 can be made by defrosting My Computer
without specifying anything <Fig. 4-5-2>.
3.5inch FD(A:)
Then, copy the folder named FinePixS3100_3500_W in this
folder in C drive <Fig. 4-5-3>. (C:)
The folder of ZJ00807-100 becomes unnecessary at the
end, and delete this folder.
ZJ00807-100
FinePixS3100_3500_W
<Fig. 4-5-3>
(Caution)[Important]
(a) PC adjustment software can not start when there is folder of
FinePixS3100_3500_W in folder named ZJ00807-100 (Fig. 4-5-3).
Please preserve the folder of FinePixS3100_3500_W right under C drive (Fig. 4-5-3).
(b) Please do not change the foldername named FinePixS3100_3500.
PC adjustment software can not start when foldername is changed.
<Step 1>
DSC jig driver(ZJ00684-100.ZIP) is downloaded from Web
server (http://fujifilm-di.intranets.com/).
<Step 2>
Defrost the downloaded compression software
<Fig. 4-5-4>
<Step 3>
(1)
Double-click setup.exe in the folder of defrosted ZJ00684-100
and install Fuji FILM DSC Jig Driver as follows.
<Step 4>
Install the software in [C:\ProgramFiles\Fjig]
according to the instructions on the PC's screen.
<Fig. 4-5-5>
38
Fine Pix S3100/S3500 SERVICE MANUAL 4.Adjustment
4-6.Initial Settings of the Adjustment Software
* The initial settings are already written in the "FFW.ini" file,
therefore perform the following procedure to the letter.
Note that, if you change file names, the software will not
start up.
<Step 1>
Double-click on the "FFW.exe" execute file of the adjustment
software to open the "FFW Startup" screen (Fig. 4-6-1).
FinePix S3100_3500_W Adjustment Software Start-up Screen
<Fig. 4-6-1>
<Fig. 4-6-2>
39
4.Adjustment Fine Pix S3100/S3500 SERVICE MANUAL
<Step 3> (2) (1)
Select the "EVR & Comm" tab ([1] in Fig. 4-6-3) in the
"Customize" dialog box that appears.
Set the "EVR" items ([2] in Fig. 8) as follows.
Item Details
etc (-V2) Check
LANC page Check
<Fig. 4-6-3>
(2)
<Step 4>
Select the "Etc" tab ([1] in Fig. 4-6-4) in the "Customize"
dialog box that appears. Set the "Other" items ([2] in Fig. 4-6-
4) as follows.
Item Details
# of auto measure 0
Change mode Do not check
Use Japanese font Do not check
Don’t show OK NG Check or Do not check
<Fig. 4-6-4>
PIO 0 10 12 14 16
PIO 1 11 13 15 17
Item Details
Debug Mode Select [Default]
<Step 6>
Once the above settings have been made, click on "Apply" (3) (4)
([4] in Fig. 4-6-5) in the "Customize" dialog box to complete <Fig. 4-6-5>
setup.
This applies the setup, therefore setting is unnecessary from
the next time forward.
[Note]
If [Disable OKNG display] on the PC screen (Fig. 4-6-4) is
set to OFF, the PC screen displays [OK] if adjustment is
OK,and [NG] if adjustment is NG(either setting is OK).
40
Fine Pix S3100/S3500 SERVICE MANUAL 4.Adjustment
Cautions When Adjusting
*1) FinePix S3100_3500 cannot adjust the EVR data
reading and writing.(Details are right tables.) Menu Command Details
Operation Start Program start
*2) End Setting returns the camera from the Jig mode to Stop Program stop
the Product Mode. Temporary stop Temporary program stop
End Setting is required when using the PC Step 0 Do not use
adjustment software, even when replacing boards or End Terminate program
units other than those noted above. Failure to run Program Reload Program (*.ff) reload
End Setting will prevent identification as Mass Select Program (*.ff) select
Storage. Edit Program (*.ff) edit
When the camera is connected to the PC, and Data ad[ ] Do not use
prevent communication with the PC. rd[ ] Do not use
SW Do not use
*3) When all adjustment have been completed, always fsw Do not use
check that the camera is identified as Mass Storage. EVR Do not use *1)
Mode File record Do not use
NGSTOP Program stopped if
adjustment is NG
STEP Do not use
LINE Do not use
AUTO Do not use
Setting OKNG clear Do not use
Mode set Sets up mode
Automaticadjustment Execution setting for Auto
Adjust in user program
Help Help Basic software help
FF help User program help
Focus Not used with this
adjustment software
Version Version information for
basic software
<Table> FFW.exe Commands
41
4.Adjustment Fine Pix S3100/S3500 SERVICE MANUAL
<Step 2>
Run the adjustment in accordance with the instructions on the screen.
<Fig. 4-7-2>
—> The [Cautions When Using the Adjustment Software] screen appears.
<Step 3>
<Fig. 4-7-2>
42
Fine Pix S3100/S3500 SERVICE MANUAL 4.Adjustment
<Step 4>
<Fig. 4-7-3>
<Step 5>
FirmWare = 1.38
Vendor Name =FUJIFILM
Manufacturer =FUJIFILM
ProductName =FinePix
Device Type =CAMERA
SerialNo =Y-641^^^^^040707C0PX0000000001
Frame Work =1.00
<Fig. 4-7-4>
<Note>
(1) [F1] Battery Adjustment cannot be run unless the Power cable jig is used to supply power to the camera.
(2) When new MAIN PWB ASSY is replaced, MAIN PWB ASSY is automatically initialized. At that time, wait for one-two
minutes, and advance the adjustment according to the instruction of the adjustment software.
43
4.Adjustment Fine Pix S3100/S3500 SERVICE MANUAL
<Step 6>
1. [ F 5 ] : Camera Adjustment
2. [ F 4 ] : CCD Defect Correction
3. [ F 6 ] : AF/Zoom Adjustment
4. [ F 7 ] : Flash Adjustment
5. [ F 1 ] : Battery Voltage Adjustment
6. [ F11 ] : VIDEO Adjustment
7. [ F 3 ] : LCD Adjustment
8. [ F12 ] : End Setting
[ F 8 ] : Firmware Download
[Execute this item only when
need to change the firmware.]
[ X ] : Restart
Fx S3100_3500 W PC Soft Ver.1.00
<Fig. 4-7-5>
<Note>
(1) ‘FxS3100_3500 W PC Soft Ver.1.00’ at the bottom-right of the screen indicates the version number of the adjustment
software.
(2) After running firmware download, other adjustments may be required depending on the content of the download
software. In such cases, the items to be adjusted, and the sequence of adjustment, will be indicated separately.
(3) After starting the adjustment software and beginning communication with the camera, always run End Setting following
adjustment and before returning the camera to the customer. If the End Setting is not run, the PC will not recognize the
camera when the two are connected.
Reason: As the camera will remain in the Jig mode (repair mode), it will not be recognized with the normal camera
drivers.
(4) When the adjustment is interrupted after the [X]:Restart key is pushed, it remains about the Jig mode.
44
Fine Pix S3100/S3500 SERVICE MANUAL 4.Adjustment
4-8.[F5] : CAMERA Adjustment
(shutter adjustment, adjustment for reduced aperture sensitivity, ISO sensitivity adjustment, white balance
adjustment, AE adjustment, offset level adjustment)
Maximum60mm
Maximum 5mm
Maximum50mm
Camera
Centerline
Pattern box
Filter (LB140)
<Step 2>
Run the adjustment in accordance with the instructions on the screen.
CAMERA Adjustment
< CAMERA Adjustment Preparations >
<Fig. 4-8-1>
<Note>
An error will occur during CAMERA adjustment, and adjustment cannot be completed, unless the pattern box is calibrated
correctly.
45
4.Adjustment Fine Pix S3100/S3500 SERVICE MANUAL
<Step 3>
Shutter adjustment
(1) Set the distance between the camera and pattern box.
(2) The LB140 filter is not placed in front of the lens.
------------------------------
| | |
| 5mm or | 50mm or less. |
| less. | |
<--Center--> | <------ Center ------> Pattern box |
(PTB450) |
CAMERA |
| |
------------------------------
<Step 4>
| ------------------------------
| | | |
| 5mm or | 50mm or less. |
| less. | |
<--Center--> | <------ Center ------> Pattern box |
(PTB450) |
CAMERA |
| |
------------------------------
46
Fine Pix S3100/S3500 SERVICE MANUAL 4.Adjustment
<Step 5>
------------------------------
| <------------> <---------------------> | |
| 5mm or | 50mm or less. |
| less. | |
<--Center--> | <------ Center ------> Pattern box |
(PTB450) |
CAMERA |
| |
------------------------------
—> Write the adjustment data to the flash ROM when adjustment has been completed correctly.
—> The [CAMERA Adjustment Complete] screen appears.
<Step 6>
<Fig. 4-8-5>
47
4.Adjustment Fine Pix S3100/S3500 SERVICE MANUAL
Maximum 30mm
Camera
Centerline
Pattern box
<Step 1>
Select [F4] CCD Defect Correction Adjustment on the [Adjustment Items Select] screen.
—> The [CCD Defect Correction Adjustment Preparation] screen appears.
<Step 2>
Run the adjustment in accordance with the instructions on the screen.
<Fig. 4-9-1>
48
Fine Pix S3100/S3500 SERVICE MANUAL 4.Adjustment
<Step 3>
—> Write the adjustment data to the flash ROM when adjustment has been completed correctly.
------------------------------
| <--------------------> | |
| 30mm or less |
| |
Pattern box |
(PTB450) |
CAMERA |
| |
------------------------------
< Setup for CCD Defect Correction Adjustment >
<Fig. 4-9-2>
<Step 4>
<Fig. 4-9-3>
49
4.Adjustment Fine Pix S3100/S3500 SERVICE MANUAL
4-10.[F6] : AF Adjustment
<Setup for AF Adjustment>
(1) Adjust the distance between the Siemens star chart and the lens front of the camera to "904+-5mm"
(2) Illuminate the AF chart with a light source. Ensure that the brightness at the surface of the AF chart is between 9.0 and
11.5EV.
(3) Place the conversion lens concentric with the camera lens.
Siemens star chart
Camera
Centerline
Lens Stand
904mm±5mm
<Step 1>
Select [F6] AF Adjustment on the [Adjustment Items Select] screen.
—> The [AF Adjustment Preparation] screen appears.
<Step 2>
Run the adjustment in accordance with the instructions on the screen.
AF Adjustment
< AF Adjustment Preparations >
<Fig. 4-10-1>
<Note>
Always use a 900mm conversion lens.
—> The [AF Adjustment (INF) Start] screen appears.
50
Fine Pix S3100/S3500 SERVICE MANUAL 4.Adjustment
<Step 3>
AF Adjustment
(1) Place the Siemens star chart at a distance of 904+-5mm
from the lens-face of the conversion lens.
(2) Place the conversion lens at a distance of 14+-2mm from
the lens-face of the lens.
(3) Adjust the position of the camera so that the center of
the AF chart is displayed in the camera LCD.
When preparations (1) - (3) are complete,
press the [Enter] key on the PC.
| <-----------------------------------904 +-5mm-----------------------------------> |
| |
14 +-2mm
<->
<-----------------------------------Center----------------------------------->
---Conversion lens
CAMERA |
=== < Setup for AF Adjustment > AF chart
<Fig. 4-10-2>
—> Write the adjustment data to the flash ROM when adjustment has been completed correctly.
—> The [AF Adjustment Complete] screen appears.
<Step 4>
<Fig. 4-10-3>
51
4.Adjustment Fine Pix S3100/S3500 SERVICE MANUAL
Camera 1000mm±10mm
Centerline
Gray chart
Setup for Flash Adjustment
<Step 1>
Select [F7] Flash Adjustment on the [Adjustment Items Select] screen.
--> The [Flash Adjustment Preparation] screen appears.
<Step 2>
Run the adjustment in accordance with the instructions on the screen.
Flash Adjustment
< Preparations >
<Fig. 4-11-1>
52
Fine Pix S3100/S3500 SERVICE MANUAL 4.Adjustment
<Step 3>
Flash Adjustment
(1) Adjust brightness so that the periphery of the gray chart
is as dark as possible.
(2) Adjust the camera so that the entire chart is
shown on the LCD monitor.
(3) Press the flash pop-up button.
When preparations (1) and (2) are complete,
press the [Enter] key.
|<-------------------------------------------------------->
| 1000 +-10mm
|
<---------------------Center--------------------->
CAMERA
--> Write the adjustment data to the flash ROM when adjustment has been completed correctly.
--> The [Flash Adjustment Complete] screen appears.
<Step 4>
53
4.Adjustment Fine Pix S3100/S3500 SERVICE MANUAL
<Step 1>
Select [F1] Battery Voltage Adjustment on the [Adjustment Items Select] screen.
—> The [Battery Voltage Adjustment Preparation] screen appears.
54
Fine Pix S3100/S3500 SERVICE MANUAL 4.Adjustment
<Step 2>
Run the adjustment in accordance with the instructions on the screen.
1. Check that the Power cable jig and the camera are connected.
*If not, return to the Jig Mode Setup screen,
and connect the Power cable jig and the camera.
2. Supply power (5.0V) to the camera from the
[ Power cable jig].
When preparations are complete, press the [Enter] key on the PC.
---> Lens is extended when the [Enter] key is pressed.
<Fig. 4-12-1>
<Step 3>
<Fig. 4-12-2>
55
4.Adjustment Fine Pix S3100/S3500 SERVICE MANUAL
<Step 4>
<Fig. 4-12-3>
<Step 5>
<Fig. 4-12-4>
—> Write the adjustment data to the Flash ROM when adjustment has been completed correctly.
—> The [Battery Voltage Adjustment Complete] screen appears.
56
Fine Pix S3100/S3500 SERVICE MANUAL 4.Adjustment
<Step 6>
<Fig. 4-12-5>
57
4.Adjustment Fine Pix S3100/S3500 SERVICE MANUAL
<Step 1>
Select [F11] Video Adjustment on the [Adjustment Items Select] screen.
—> The [Video Adjustment Preparation] screen appears.
58
Fine Pix S3100/S3500 SERVICE MANUAL 4.Adjustment
<Step 2>
Run the adjustment in accordance with the instructions on the screen.
VIDEO Adjustment
< VIDEO Adjustment Preparations >
(1) Connect the camera and video adj. jig with the video cable.
(2) Confirm Video jig is connected with the video cable.
<Fig. 4-13-1>
—> Write the adjustment data to the Flash ROM when adjustment has been completed correctly.
—> The [VIDEO Adjustment Complete] screen appears.
<Step 3>
<Fig. 4-13-3>
59
4.Adjustment Fine Pix S3100/S3500 SERVICE MANUAL
<Step 1>
Select [F3] LCD Adjustment on the [Adjustment Items Select] screen.
—> The [LCD Adjustment Start] screen appears.
<Step 2>
Run the adjustment in accordance with the instructions on the screen.
—> The [LCD Adjustment Complete] screen appears if download is successful.
60
Fine Pix S3100/S3500 SERVICE MANUAL 4.Adjustment
<Step 3>
LCD Adjustment
< LCD Adjustment Preparations >
(1) Check that the LCD adjustment xD-Picture card has been
inserted in the camera.
(2) Adjust so that the center of the camera LCD monitor is
in the LCD adjustment jig the sensor.
(3) Ensure that the periphery is as dark as possible.
(4) Confirm the VIDEO cable is not connected with the camera.
<Fig. 4-14-1>
—> Write the adjustment data to the Flash ROM when adjustment has been completed correctly.
—> The [LCD Adjustment Complete] screen appears.
<Step 4>
<Fig. 4-14-2>
61
4.Adjustment Fine Pix S3100/S3500 SERVICE MANUAL
<Step 1>
Select [F8] Firmware Download on the [Adjustment Items Select] screen.
—> The [Firmware Download Start] screen appears.
62
Fine Pix S3100/S3500 SERVICE MANUAL 4.Adjustment
<Step 2>
Run the adjustment in accordance with the instructions on the screen.
Firmware Download
LED lights to orange while downloading the firmware.
Do not turn off the power while downloading the firmware.
c:\FinePixS3100_3500_W\Firmwear\SU541.bin
<Fig. 4-15-1>
<Step 3>
<Fig. 4-15-2>
63
4.Adjustment Fine Pix S3100/S3500 SERVICE MANUAL
Item Details
Repair Date Date information is acquired from the PC and written.
Administrator ID C(43)
Repair Station U.S. 61(a) SAPPORO 30(0)
Canada 62(b) SENDAI 31(1)
Hawaii 63(c) TOKYO 33(3)
Taiwan 64(d) NAGOYA 34(4)
England 66(f) OSAKA 35(5)
Germany 67(g) HIROSHIMA 37(7)
France 68(h) FUKUOKA 38(8)
Spain 69(i)
Italy 6A(j)
Netherlands 6B(k)
Belgium 6C(l)
Sweden 6D(m)
Switzerland 6E(n)
Norway 6F(o)
Finland 70(p)
Singapore 71(q)
China 74(t)
Ohter 7A(z)
Repair Serial No. A serial No. is assigned automatically and written
64
Fine Pix S3100/S3500 SERVICE MANUAL 4.Adjustment
<Step 1>
Select [F12] End Setting on the [Adjustment Items Select] screen.
—> The [End Setting Description] screen appears.
<Step 2>
Run the adjustment in accordance with the instructions on the screen.
End Setting
The End settings consist of the destination setting,
the USB_ID write, and product mode settings
(= Mass Storage recognition).
<Fig. 4-16-1>
<Step 3>
Destination setting
The destination is selected from an undermentioned list,
according to third character from left side of the serial number.
<Fig. 4-16-2>
<Note>
This example assumes that <B>US-Model has been selected. The following screen therefore appears.
—> The [US-Model selected] screen appears.
65
4.Adjustment Fine Pix S3100/S3500 SERVICE MANUAL
<Step 4>
Destination setting
The destination is selected from an undermentioned list,
according to third character from left side of the serial number.
<Fig. 4-16-3>
<Step 5>
<Fig. 4-16-4>
<Note>
This example assumes that <H>USA has been selected. The following screen therefore appears.
—> The [USA_ID USA] screen appears.
66
Fine Pix S3100/S3500 SERVICE MANUAL 4.Adjustment
<Step 6>
USB ID
Selected USA.
<Fig. 4-16-5>
<Step 7>
--> The adjustment software returns to the Jig mode setup screen
after press the [Enter] key.
<Fig. 4-16-6>
67
5. Inspection Fine Pix S3100/S3500 SERVICE MANUAL
5. Inspection
5-1. Required Measuring Equipment
Measuring equipment Remarks
Power supply AC adapter (AC-5VH), stabilized power supply
Digital voltmeter For general use
Ammeter For general use (able to measure 1mA or less)
power cable jig For general use
xD-Picture card For general use
Macro Chart Resolution confirmation (ZJ00525-100)
TV Monitor NTSC or PAL, TV monitor, minimum resolution 600 lines
2 Power supply Auto (1) Place battery in camera. (1) Approximately 4.5V with four
switch photography (2) Insert xD-Picture card and AA-sized batteries.
LCD_ON close cover. (2) Recording check card.
(3) Set mode dial to still
photography mode. (4) Power supply LED is green
(4) Switch power supply ON. and beeps.
(5) Through screen and text
(5) If the date set message display in EVF.
appears, press Cancel.
3 Check LCD Auto (1) Press EVF/LCD button. (1) Check that EVF is
extinguished, and that
photography through screen appears on
LCD monitor.
4 Check Movie Auto (1) Apply an appropriate shock (1) No problem with display on LCD monitor
mode shock noise photography to the camera. LCD monitor.
LCD_ON * Do not apply shock directly Restoration possible despite
disruption of sync.
to the lens or card cover.
68
Fine Pix S3100/S3500 SERVICE MANUAL 5. Inspection
Preparations for adjustment Method of adjustment Measuring Measurement points
Sequence Item Mode
(measurement points, subject, other) (VRs, waveforms, required values) equipment and jigs (VRs, positions)
5 Check macro Auto (1) Macro photography (1) Macro icon appears in LCD
photography photography distance (approximately monitor.
Check focus LCD_ON 10~80cm). (2) LED beside viewfinder
changes from green to
(2) Press shutter button to orange (recording) to green.
take photographs.
6 Movie/audio Movie (1) Select Movie mode. (1) Standby display on LCD.
recording check photography (2) Half-press shutter button (2) Movie/audio recording
LCD_ON -> full-press -> full-press begins. Recording displayed
on LCD.
-> half-press -> release. (3) Movie/audio recording
(3) Half-press five seconds completed. Recording on
later -> release. xD-Picture card.
8 Card cover detect M mode (1) Open card cover to check LCD monitor
check LCD_ON recording.
(2) Remove xD-Picture card.
Delete mode Delete (1) Select <Delete all frames> (1) [OK to delete all frames?]
10 check from the menu, and press displayed.
the <OK> button. (2) Movie/photography
(2) Press the <OK> button screen extinguished.
again.
11 Battery low check Movie (1) Connect power cable jig Refer to Battery Adjustment Power supply
for connection details. cable jig
(2) Set voltage. (2) Set voltage to 5.0±0.3V. Stabilized
(3) Set mode dial to Replay (3) Starts normally. power supply
mode, and switch main
power ON.
(4) Set to pre-end voltage. (4) Set voltage to 4.4±0.1V.
Battery warning
displayed.
(5) Set to end voltage. (5) Set voltage to 4.0±0.1V.
Lens retracts and main
power switched OFF.
13 Leak current Power (1) Switch power OFF. (1) Maximum leak current Ammeter
OFF 0.5mA.
14 Factory setting Playback (1) Set mode dial to Camera * Setting and clearing date
mode. (1) Connect the USB cable
(2) Return all settings to initial from the PC to the camera
values. (ensure that the PC is
Flash: Auto switched ON).
Monitor brightness: Center (2) Open the card cover and
Power saving: OFF switch power ON
USB setting: Card (POWER_ON) while
reader pressing the shutter
Beep: LOW button.
Pixels: 1M normal (3) Switch power OFF
Photography mode: A mode (POWER_OFF).
Date: Not set (4) Check that the date has
(3) Inspection battery/ been cleared.
inspection xD-Picture card
not inserted in camera.
(4) Battery cover closed.
(5) LCD/EVF surface free of
contamination.
(6) Clean exterior of camera.
69
6.Parts list Fine Pix S3100/S3500 SERVICE MANUAL
6.Parts list
6-1.Packing and Accessoris
6-1-1.FinePix S3100 (US model)
A109 A108
A118
A119 A117
A121
A122
A102
A120
A105
A114
A104
A112
A115 A103
A110
A113
Ref No. Parts No. Description Comment EL Ref No. Parts No. Description Comment EL
70
Fine Pix S3100/S3500 SERVICE MANUAL 6.Parts list
6-1-2.FinePix S3100 (CA model)
A109 A108
A120
A121 A117
A118
A119
A102
A105
A114
A104
A112
A115 A103
A110
A113
Ref No. Parts No. Description Comment EL Ref No. Parts No. Description Comment EL
71
6.Parts list Fine Pix S3100/S3500 SERVICE MANUAL
A109 A108
A121
A122
A123
A124 A117
A118
A119
A120
A102
A105
A114
A104
A112
A115 A103
A110
A113
Ref No. Parts No. Description Comment EL Ref No. Parts No. Description Comment EL
72
Fine Pix S3100/S3500 SERVICE MANUAL 6.Parts list
6-1-4.FinePix S3500 (EG model)
A109 A108
A118
A117
A120
A102
A119
A105
A114
A104
A112
A115 A103
A110
A113
Ref No. Parts No. Description Comment EL Ref No. Parts No. Description Comment EL
73
6.Parts list Fine Pix S3100/S3500 SERVICE MANUAL
A109 A108
A119 A117
A118
A102
A105
A114
A104
A112
A115 A103
A110
A113
Ref No. Parts No. Description Comment EL Ref No. Parts No. Description Comment EL
74
Fine Pix S3100/S3500 SERVICE MANUAL 6.Parts list
6-1-6.FinePix S3500 (AS model)
A109 A108
A119 A117
A118
A102
A105
A114
A104
A112
A115 A103
A110
A113
Ref No. Parts No. Description Comment EL Ref No. Parts No. Description Comment EL
75
6.Parts list Fine Pix S3100/S3500 SERVICE MANUAL
6-2.Cabinet F block
6-2-1.FinePix S3100(US/CA model)
M217
B
M201 M216
C
D
M208 N.S A
M209
M210 M212
M213
M211
M220
M214
M204
M207
M215
M206
M202
M218
M205 M203 M221
M219
Ref No. Parts No. Description Comment EL Ref No. Parts No. Description Comment EL
76
Fine Pix S3100/S3500 SERVICE MANUAL 6.Parts list
6-2-2.FinePix S3500(EU/EG/GE/AS model)
M217
B
M201 M216
C
D
M208 N.S A
M209
M210 M212
M213
M211
M220
M214
M204
M207
M215
M206
M202
M218
M205 M203 M221
M219
Ref No. Parts No. Description Comment EL Ref No. Parts No. Description Comment EL
77
6.Parts list Fine Pix S3100/S3500 SERVICE MANUAL
6-3.Inner block
M314 M315
M328
N.S
M323
Ref No. Parts No. Description Comment EL Ref No. Parts No. Description Comment EL
78
Fine Pix S3100/S3500 SERVICE MANUAL 6.Parts list
6-4.Cabinet R block
M405
M408
M420 M421
M416
M409
M406
M414
M412 M422
M413
M415 M411
M401 M403
M404
M410
O M419
M402
M418
M403 M403
M407
M417
M422
Ref No. Parts No. Description Comment EL Ref No. Parts No. Description Comment EL
79
6.Parts list Fine Pix S3100/S3500 SERVICE MANUAL
6-5.Electrical parts
[Note]
The components indicated by mark are critical for safty. * Due to standardization,replacement in the parts list may be
When indicated parts by reference number, please different from the parts list specified in the circuit or the com-
include the board name. ponents used on the set.
Ref No. Parts No. Description Comment EL Ref No. Parts No. Description Comment EL
[SWITCH] [FUSE]
SW851 FZ02084-100 TACT SWITCH N F601 FP00018-253 FUSE 2.5A 125V JIS N
SW852 FZ02084-100 TACT SWITCH N F602 FP00039-253 FUSE 2.5A 32V UL N
SW853 FZ02084-100 TACT SWITCH N F603 FP00039-253 FUSE 2.5A 32V UL N
SW854 FZ04294-100 TACT SWITCH N F604 FP00039-153 FUSE 1.5A 32V UL N
SW855 FZ02084-100 TACT SWITCH N F605 FP00039-502 FUSE 500MA 32V UL N
SW856 FZ04294-100 TACT SWITCH N
SW857 FZ04294-100 TACT SWITCH N [CONNECTOR]
SW858 FZ02084-100 TACT SWITCH N CN601 FGA113-0021 CONNECTOR CJ 2P RN 1.5MM PH N
CN602 FGC143-0501 CONNECTOR CJ 50P BN 0.5MM RV N
[CONNECTOR] CN701 FGA137-0042 CONNECTOR LJ 4P RB 2.0MM PH N
CN851 FGB066-0061 CONNECTOR CJ 6P FN 0.5MM NH N CN751 FGA058-0021 CONNECTOR CJ 2P RN 1.25MM PN N
[SWITCH]
[IC]
SW201 FZ01045-100 DETECTOR SWITCH N
IC701 FQTY0031-01 FET
[BUZZER] [JACK]
BZ201 FZ04744-100 BUZZER N J971 FZ04344-100 JACK_MINI 4P YELLOW N
[SWITCH]
CN951 FGB113-0061 CONNECTOR CJ 6P FN 0.5MM NH N
[CONNECTOR]
SW952 FZ02629-100 TACT SWITCH N
[SWITCH]
SW901 FZ04725-100 DETECTOR SWITCH N
SW902 FZ04725-100 DETECTOR SWITCH N
SW903 FZ04817-100 DETECTOR SWITCH N
SW904 FZ04817-100 DETECTOR SWITCH N
[CONNECTOR]
CN901 FGB113-0121 CONNECTOR CJ 12P FN 0.5MM NH N
Revised: 14. Oct. 2004 CN902 FGB113-0061 CONNECTOR CJ 6P FN 0.5MM NH N
80
Fine Pix S3100/3500 SERVICE MANUAL 7.Appndix
7.Appendix
7-1. Version display function
<Fig. 2>
81
7.Appndix Fine Pix S3100/3500 SERVICE MANUAL
82
FUJI PHOTO FILM CO., LTD.
26-30, Nishiazabu 2-chome, Minato-ku, Tokyo 106-8620, Japan.