INSTALLATION PRECAUTIONS
The high degree of craftsmanship in the construction and • Cotton gloves are preferable. They will protect the surface
finish of your metal liner insert requires careful handling to from fine scratches and eliminate fingerprints.
ensure proper installation.
• Do not remove your metal liner insert from its carton until • Remove all rings, watches, belt buckles, and jackets
you are ready to hang it. (snaps-zippers) to prevent scratch marks.
2
MODEL OPTIONS
Model Electric Motor Material
3
INSTALLATION PLANNING
• If the installation has not been roughed in, check what is needed to create the framing and mounting hardware (allthreads,
nuts, etc.). Be sure the location will not interfere with wiring, other utilities, or structural considerations.
Location
of
Wood Hood Metal Liner Electrical
Metal Liner
10" Round Duct
Wood Hood 6"
Transition
5"
EZ Install B
Mounting
MODEL A B
PMLSS 22 1/2" 12" The hoods are designed for vertical discharge
MLSS 19 1/4" 14" as shown.
MLFS 24" 12"
CMLSS 15 13/16" 11 1/8"
4
STEP 1. REMOVAL AND INSTALLATION OF TRANSITION
1. The hood assembly is shipped with the rough-
in plate and the transition attached.
Note: The transition is shipped upside down in Shipping Screws
the hood assembly and must be removed and
reinstalled (See Steps 1 through 2.) If in-hood Rough-in Plate
fan is furnished the transition is shipped
Transition
separately.
2. To detach the rough-in plate/transition from the Hood
hood assembly, remove the four (4) screws on Assembly
the top and four (4) screws on the back of the
assembly as shown in Figure 1.
3. Detach the transition from the rough-in plate by
removing four (4) screws. The shipping screws
are needed for re-installing the transition to the
rough-in plate.
4. Secure the transition to the top of the rough-in
plate, using four (4) screws provided. Use duct
tape to seal the joints of the transition and the Figure 1. Model MLFS
top of the rough-in plate. See Figure 2.
5. Re-install rough-in plate to hood then install
hood.
Shipping Screws
10" Transition
Duct Tape
Rough-in Plate
Figure 2.
5
STEP 2. INSTALLATION OF METAL LINER-INSERTS
1. If the optional trim kit is used it must be installed prior 3. Install #6 x 1/2" screws through the pre-drilled EZ
to mounting the Metal Hood Liner into the wood mount holes into the decorative hood structure. Tap
decorative hood. Use the provided #8 Phillips head chrome cap into EZ mount holes for flush appearance
screws. See Figure 3. See Figure 4A.
2. Lift the Metal Hood Liner into the decorative hood 4. Additional mounting fasteners may be used to secure
structure. Due to the weight of the assembly three to the back wall and top (from inside).
people may be required for proper installation.
5. Install blower assembly, see page 4.
Optional
Trim
Mounting
Trim Screws
Screws
EZ
MLSS Wood Mounting MLSS
Figure 3. PLMSS Figure 4 . Hood Holes PLMSS
EZ Mounting Detail
Chrome
Cap
#6 x 1/2" Screw
EZ Mounting
Hole
Figure 4A.
6
STEP 3. ELECTRICAL CONNECTION
Power Supply
To Remote
1. Install three wires: black, white and green (#16 AWG) in Fan
1/2" conduit from the service panel to the hood junction (if used)
3. Remove the junction box from the rough-in plate. Connect Fan Plate
Keyhole
black wire to power supply black wire, white wire to power
supply white wire, and green wire to power supply green
wire.
Fan Motor
4. Place all wiring connectors inside junction box and re- Assembly Molex Plug
install on rough-in plate. Connector
Figure 5. CFM1200
2-1/2"
2"
3-3/4"
3"
2-1/2" 2-1/2"
3"
MLSS-28 & 34
Figure 6B. MLFS Figure 6D. PMLSS-28 & 34
7
STEP 4. MOUNTING THE IN-HOOD FAN
Independent installs the CFM600 fan at the factory CFM600 IN-HOOD FAN
in models CMLSS-29-SS-6, CMLSS-38-SS-6, MLSS-
28-SS-6 and PMLSS-28-SS-6.
Figure 7.
CFM1200
Fan Plate
Keyhole
Fan Motor
Assembly
Molex Plug
1. For in-hood fans, use 10" round-duct from the 3. The length of ducting should be as short and straight
transition (provided). as possible for best performance of fan. SEAL ALL
JOINTS WITH DUCT TAPE.
2. For remote fans, use 10" round-duct from the
transition (provided) to the remote fan.
8
COMPACT METAL LINER SLOPED SIDES (CMLSS)
(WOOD HOODS, STUCCO AND TILE HOODS)
18"
14-13/16" 26-5/8"
8" Transition
2"
10"
1/2"
3-3/4"
11-1/8"
HEIGHT
4-1/2"
X 25-15/16"
34-9/16"
WIDTH
29-13/16"
38-7/16"
WIDTH 15-13/16"
FRONT
TO
BACK
1-15/16"
Damper Assembly
(Shown one side open 45 degrees) CFM600
3-1/4"
4-1/4"
1/2" 14-13/16"
16-3/4"
17-1/4"
25-15/16"
34-9/16"
WIDTH
POSITION OF TRANSITION
(TOP VIEW)
14-13/16"
12"
UPPER
REVEAL 10" Transition 22-3/8"
DEPTH 28-3/8"
34-3/8"
40-3/8"
46-3/8"
52-3/8"
WIDTH
4"
LOWER
REVEAL
HEIGHT
28-3/8"
34-3/8" 14"
X 40-3/8" HEIGHT
46-3/8"
52-3/8"
58-3/8"
WIDTH
19-1/4"
FRONT
TO
BACK
3-1/4"
4-1/4"
8-1/2" 8" 10" Transition
1/2" 12" 12"
1/2"
16-3/4"
17-1/4"
20"
28-3/8" 21-1/4"
34-3/8"
40-3/8" 1/2"
28-3/8"
46-3/8" 34-3/8"
52-3/8" 40-3/8"
WIDTH 46-3/8"
52-3/8"
WIDTH
POSITION OF TRANSITION
(TOP VIEW)
19-1/4"
12"
UPPER
REVEAL 10" Transition
22-3/8"
DEPTH 28-3/8"
34-3/8"
40-3/8"
46-3/8"
52-3/8"
WIDTH
4"
LOWER
REVEAL
HEIGHT
28-3/8" 12"
34-3/8"
X 40-3/8"
HEIGHT
46-3/8"
52-3/8"
58-3/8"
WIDTH
22-1/2"
FRONT
TO
BACK
3-1/4"
4-1/4"
8 1/2" 8" 10" Transition
1/2" 12" 12"
1/2"
16-3/4"
17-1/4"
20"
22-3/8"
28-3/8" 21-1/4"
34-3/8" 1/2"
22-3/8"
40-3/8" 28-3/8"
46-3/8" 34-3/8"
52-3/8" 40-3/8"
WIDTH 46-3/8"
POSITION OF TRANSITION 52-3/8"
(TOP VIEW) WIDTH
22-1/2"
2"
LOWER
REVEAL
HEIGHT
18"
HEIGHT
30"
36"
X 42"
48"
54"
60"
WIDTH 24"
FRONT
TO
BACK
3-1/4"
4-1/4"
8-1/2" 8" 10" Transition
1/2" 12" 12"
1/2"
16-3/4"
17-1/4"
30" 20"
36" 21-1/4"
42" 1/2"
48" 30"
54" 36"
60" 42"
WIDTH 48"
54"
60"
WIDTH
POSITION OF TRANSITION
(TOP VIEW)
24"
2. In the center of the space provided for the filters, insert one
filter on the top ledge and pull back until the bottom of
the filter slips into bottom ledge. Hood Assembly
FILTERS
OFF
LO HI
FAN
MED Wash filters frequently either in a detergent solution, or by
placing them in your dishwasher.
LIGHTS LIGHTS
CLEANING
FAN
Do not allow excessive grease to accumulate. Refer to Cleaning
The fan is controlled by a multi-speed switch. Printed Recommendations on last page for suggestions on cleaning
speeds on the control panel correspond with fan speed. metals and finishes.
13
14
WIRING DIAGRAM FOR METAL LINER INSERTS
BLUE GREEN
18 G
BLACK TERMINAL BLOCK
BLACK BLACK
15 5 9
14
G
R BLACK
INTERNAL 14 9 L1
BLOWER BL 3 6 2
CFM600 OR 15 6-PIN 5
BK 2 5 CONNECTOR 1 L1 2
CFM1200
W BLACK NO < 200F
1 4 3 21 3 1
NC < 200F
RED WHITE
6 3 16 16 FAN HI-HEAT 5 N
SWITCH THERMOSTAT
5 2
WHITE WHITE
4 1 17 17
BLACK
SEE DETAIL
8
G
R YELLOW YELLOW YELLOW
1 1 1
REMOTE BL
FAN BK
R 3-LIGHT 2-LIGHT 2-LIGHT
W UNIT UNIT UNIT BLACK 3
BL HALOGEN HALOGEN LEFT RIGHT HALOGEN 2
BK LIGHT LIGHT LIGHT
LIGHT
DIODE
SWITCH
W 1
6
WHITE BLACK
13 2
SWITCH
(LEFT)
1
HEATLAMP
YELLOW
1
7
BLACK
HEATLAMP HEATLAMP 2
(LEFT) (RIGHT)
SWITCH
(RIGHT)
1
HEATLAMP
BROWN
BLACK NOT USED 2
TO HIGH SETTING 14 3 6
BLUE NOT USED
TO MED. SETTING 15 2 5
WHITE
12
RED WHITE
TO LOW. SETTING 16 1 4 17 TO TERMINAL
6-PIN
CONNECTOR
IN-HOOD & REMOTE FANS
MODEL VOLUMETRIC FLOW RATE FOR EQUIVILENT DUCT LENGTHS APPLICATION
10"
600 Duct Dimensions
3.8 Amps @ 115V AC, 60 Hz
251/4"
7" dia.
Duct Size at Discharge:
3-1/4" X 16-3/4" X 8" Round Transition
500
3 1/4" x 10"
Use with hood series:
450
6" dia.
400
Option for ARMA, ASPEN, BONZ, CMLSS,
350 CONN, CONVX, CRES, CSNO, INCL, INHL,
300 LOUV, LP, LPHL, MLFS, MLSS, PAGO,
7 1 /4 "
0 20 40 60 80 100
Total Equivalent Duct Length, ft. POND, PINN, PMLSS, SAHA, SNFE 22, SILV,
SILH, TAHO.
CFM1200 IN-HOOD FAN Maximum CFM: 1200
Electrical Motor Rating:
CFM1200 FAN
875
CONVX, CRES, CSNO, INCL, INHL, LOUV,
800 MLFS, MLSS, PAGO, POND, PINN, PMLSS,
83/4" 0 20 40 60 80
Total Equivalent Duct Length, ft.
100
SAHA, SNFE 24 & 27, SILV, SILH, TAHO.
8 /8 "
3 600 Duct Dimensions
4.0 Amps @ 115V AC, 60 Hz
13 7/8"
Volumetric Flow Rate, CFM
350
CHIM, LARE, LARA, SNFE-I, WRAN.
300
0 20 40 60 80 100
Total Equivalent Duct Length, ft.
875
Option for CHIMNEYS ONLY;
8 5 /8 " 800 CHIM, LARE, LARA, SNFE-I, WRAN.
0 20 40 60 80 100
Total Equivalent Duct Length, ft.
1100
Option for ARMA, ASPEN, BONZ, CONN,
4" 1000 CONVX, CRES, CSNO, INCL, INHL, LOUV,
10" MLFS, MLSS, PAGO, POND, PINN, PMLSS,
28" 203/4"
900
0 20 40 60 80 100
Total Equivalent Duct Length, ft. RECT, SAHA, SNFE, SILV, SILH, TAHO,
WRAN. 15
CLEANING RECOMMENDATIONS
BRUSHED STAINLESS STEEL, HAMMERED STAINLESS, EUROPEAN BLACK STEEL, 1920’s
ANTIQUATED TIN, MILLENNIUM DISK STAINLESS
The Brushed Stainless Steel Hood should be cleaned with pre-washed flannel cloths and our recommended
“Stainless Steel” cleaner. Always wipe in a manner which follows the grain. Do Not clean with paper towels as
they will scratch the surface. Different cleaning cloths other than cotton flannel may scratch the surface of the
hood.
INTERIOR OF HOOD
All hoods are fitted with a brushed stainless steel liner. For cleaning, we recommend using pre-washed flannel
cloths and “Stainless Steel” cleaner. Always wipe in a manner, which follows the grain. Do Not clean with paper
towels, as they will scratch the surface of the hood.
Both “Kleen Glass” and “Stainless Steel” cleaner may be purchased directly from Independent, Inc.
“Brite Boy” polish may be purchased directly from Independent, Inc.
16
Please call our toll-free number, 1-800-7-NEVADA (763-8232), to place your order.
NOTES
17
NOTES
18
NOTES
19
Independent Inc. reserves the right to change specifications or design without notice. Some models are certified for use
in Canada. Independent Inc. is not responsible for products which are transported from the United States for use in
Canada. Check with your local Canadian distributor or dealer.
UL
®
C UL ®
The Ultimate Temptation In Luxury Hoods