Assembly diagram
Thank you for choosing Smart Sensor Metal
Detector. This unit adopt latest electronic technology
Model: AR924 + m
provide with ground balance function which can ste
er
eliminate the effect caused by “Mineralization Up
p
Metal Detector reaction”, besides the metal type mode can identify
02 Main pan el
01
3. Parts and assembly diagram ⑤ Normal scan and metal type mode selection 5. Specification
3.1 Parts ⑥ Sensitivity adjustment button Max. 1.5m (50CMx50CMx1.2CM
Detection depth aluminium board )
While purchasing, check the package ⑦ Charging indication
Audio(≥75dB) and
contents carefully: ⑧ LCD Detectable indication
light indication
<01>Upper stem*1PCS ⑨ Earphone jack Ground balance/
Detection mode
⑩ Charging port discrimination
<02>Main panel*1PCS
<03>3.7 V li-battery*1PCS ⑩
11 Voice adjustment switch Signal frequency 7.1KHz
<15>Nylon screw
② ③ ④ ⑤
10-15cm
Operations as below: d. Whatever use normal scan or metal type mode, the battery is wrong if blinking for a long time.
a. Slide switch to Metal Type. when there is 6 or more than 6 bar graphs icon on
b. Power on and after auto calibration ,slowly LCD, please adopt manual ground balance
sweep the coil above the metal being located, adjustment mentioned above. You should adopt
the detector gives out audio sound with increasing manual ground balance the detector regularly, keep
bar graphs. If the LCD display “nonferrous metal” it eliminate interference by electromagnetic or
means the target is nonferrous metal; if display mineralize soil promptly. At the course of hunting,
“ferrous metal” means the target is ferrous metal. eliminate Mineralization reaction & identify / reject
Thus, you can distinguish the metal target by LCD metal operation also aid you for desirable search
display. Also detect back and forth around the results. figure 5
place of metal located is needed. Eliminate the
effect maximum caused by soil structure or any e. Metal detector produce their own
other elements to enhance the accuracy of the electromagnetic fields, so if detecting with friends,
detection. (note: Ferrous: containing, pertaining keep each metal detectors at least 10 meter apart.
10. Battery installation
to or made of iron; Non ferrous therefore does not,
Open battery compartment cover, and insert into
eg: copper, aluminum, gold and so on) f. Many household appliances and facility emit
3.7V*1 li-battery into compartment, then close the
electromagnetic energy, which can interfere the
compartment door. See figure 6 :
Cautions: detector, this detector is not adapt to indoor use.
a. If the target is a ferrous metal board, a special
phenomenon will happen: Whenthe coil approach 7. Light
the wage of the target, the detector will response 7.1 When the light is needed, just slide the switch to
as located a ferrous metal; when the coil right ON position.
above the centre of the target, the detector will 7.2 In dark environment, press“ backlight ” key to
response as located a non-ferrous metal. activate, and press again, backlight off.
b. While in the operation process, when the coil 8. When LCD display icon “ ”, please replace
being disconnected with the main panel, the the batteries to ensure excellent sensitivity and
detector will give out alarm sounds “BI BI” with bar precise detection.
graphs blinking on LCD and no star icon display,
please check up the connection of lead wire. 9 Charging figure 6
9.1 Connect adapter to 110V-240V AV power, plug
c. Please use Normal scan to detect the target, the DC charger into charging hole.See figure 5:
then switch to Metal type to discriminate ferrous/ 9.2 When charging, the power light is red.
non ferrous metal. Use higher sensitivity levels 9.3 The green power light means the power is full.
(turns the ADJ knob at clockwise) before turn on 9.4 When charging, red power light keeping blinking
the unit for detecting. means battery over-temperature protection.