engine speed ?
The dashpot.
As a rule of thumb, the time interval for automatic desludging of lubricating oil purifiers fitted on
sumps of trunk-type engines should be set at _____ hours.
6 to 8
1 to 2
2 to 4
4 to 6
In the Main Engine sea water circuit why are the Lub Oil and the Scavenge air coolers fitted in
front of the jacket and piston water coolers ?
The Scavenge air and Lub Oil coolers have by-pass valves fitted.
How is expansion of the Diesel engine cylinder liner allowed 1. Liner absorbs 1. Liner is fr
2 for? stresses caused by expand at
expansion. lower end
Where will the Diesel engine exhaust temperature be the 1. At the cylinder 1. Before th
5
highest? head. turbo blo
7 Why is a by-pass fitted to the cooling water line of the charge 1. To prevent the air 1. To preven
# Question Choosed answers Right answers
Where does maximum wear take place on the cylinder liner of 1. At the top where 1. At the top
a Diesel engine? the scraper ring where the
8
changes direction. ring chan
direction.
1. A heater. 1. A heater.
When taking performance figures on a 4 stroke Diesel engine, 1. By the governor 1. By the
10 how is the quantity of fuel delivered by each pump position. position o
determined? each fuel
What is the purpose of the injection pump delivery valve? 1. To adjust the 1. To mainta
1 injection pressure. injection
pressure
the HP fu
# Question Choosed answers Right answers
line.
The timing of the engine is delayed and the exhaust 1. Cause increased 1. Cause
temperatures are high. How would you expect this to affect the turbocharger increased
2
turbocharger ? revolutions. turbochar
revolution
What could be the purpose of checking the fuel pump spill 1. To check the 1. To check
5 position on a 4stroke Diesel engine? amount of fuel the start poin
pump will deliver. injection
Lapping a valve and valve seat together means _____ . 1. machining the 1. grinding t
6 valve in a lathe. valve aga
the valve
to obtain
# Question Choosed answers Right answers
uniform
sealing
surface.
In a trunk piston Diesel engine how is the piston cooled? 1. Separate piston 1. By the
cooling oil supply. crankcase
7 spraying o
the under
of the pis
Automatic shutdown of the main diesel engine always acts on 1. fuel supply. 1. fuel supp
8
the _____
Putting additives into diesel engine cooling water is primarily 1. overheating. 1. scaling.
9
designed to prevent _____
Why do diesel engine manufacturers recommend grinding the 1. To avoid sticking 1. To improv
valve seating surface with a half degree difference to the valve between valve sealing
10 seat? and seat during between
high load and seat.
operation.
In a 2 stroke engine what controls the admission of charge air? 1. Camshaft position. 1. Upper edge
1
of piston.
If water is detected in the generator crankcase what is the 1. Leakage from 1. Leakage
most likely source? cracked cylinder from cracked
liner or perished cylinder liner
2
liner sealing rings. or perished
liner sealing
rings.
The best way to ensure engine speed governor stability is to 1. Compensation. 1. Speed droop.
3
allow a given ratio of what?
If lub oil analysis results indicate fuel dilution what should be 1. Locate and rectify 1. Locate and
the first action? source of rectify
4 contamination. source of
contaminatio
n.
How is the timing (degrees advance) adjusted on a Bosch type 1. By the plunger 1. By the fuel
5
fuel pump? rotation. cam setting.
In the formula P.L.A.N. how is `N` derived for a double acting 1. Eng rpm/60. 1. Eng rpm/30.
6
two stroke?
When all preparations have been made to ensure that the main 1. Blow indicator 1. Blow
engine is operational prior to departure, what will be the final cocks, test indicator
test to be carried out ? reversing of engine, cocks, test
9
short firing kick. reversing of
engine, short
firing kick.
10