Concise Beam, Version 4.59x, Copyright 2002-2016 Black Mint Software, Inc.
Licensed to: DEFAULT - FOR EVALUATION USE ONLY
Project: SBI MLVP PARKING BLOCK
Problem: INVERT T BEAM
SUMMARY REPORT
________________________________________________________________________________________________________________
| Segment/Length | Section Identification | Offset |
|No| From | To | Length | Folder | Section | Section | Z | Y |
| | m | m | m | Name | Name | Type | mm | mm |
________________________________________________________________________________________________________________
| 1| 0.000| 9.600| 9.600| Inverted-Tee | INVERT T | Inverted Tee | 0.0| 0.0|
________________________________________________________________________________________________________________
Span Length at Transfer = 9.000 m, Centre of Supports, Left @ 0.300 m, Right @ 9.300 m
Span Length in Service = 9.370 m, Centre of Supports, Left @ 0.115 m, Right @ 9.485 m
Total Beam Length = 9.600 m, Bearing Length, Left = 230.0 mm, Right = 230.0 mm
______________________________________________________________________________________________
| Segment/Length | Slab/Topping Parameters | Haunch Paramaters |Vertical|
|No| From | To | Length | Thick. | Width | Offset | Thick. | Width | Offset | Offset |
| | m | m | m | mm | mm | mm | mm | mm | mm | mm |
______________________________________________________________________________________________
| 1| 0.000| 9.600| 9.600| 100.0| 1400.0| 0.0| 60.0| 300.0| 0.0| 0.0|
______________________________________________________________________________________________
The beam is SHORED during the cast-in-place pour for the weight of the dead load applied before the cast-in-place pour, and the cast-in-pla
__________________________________________________________________________________________________________________________________
_______________________________________________________________________________________________________
|Seg.| Section Properties | Section| Section| Shear |Volume /| Section Moduli |
| No.| A | I | yb | Height | Width | Width | Surface| Sb | St |
| | mm^2 | mm^4 | mm | mm | mm | mm | mm | mm^3 | mm^3 |
_______________________________________________________________________________________________________
| 1| 375000 | 13.254E+9 | 317.0| 700.0| 600.0| 300.0| 144.00| -41.811E+6 | 34.606E+6 |
_______________________________________________________________________________________________________
__________________________________________________________________________________________________________________________________
GROSS COMPOSITE SECTION PROPERTIES
(based on Ec of the precast beam - transformed area of rebar and strand NOT included)
______________________________________________________________________________________________________
|Seg.| Section Properties | Section| Section Moduli |
| No.| Ac | Ic | yb | Height | Sb | St | Sbc | Stc |
| | mm^2 | mm^4 | mm | mm | mm^3 | mm^3 | mm^3 | mm^3 |
______________________________________________________________________________________________________
| 1| 495674 | 34.802E+9 | 434.8| 860.0| -80.040E+6 | 131.230E+6 | 131.230E+6 | 81.849E+6 |
______________________________________________________________________________________________________
Note: Sb & St = bottom and top of the precast beam, Sbc & Stc = bottom and top of the cast-in-place pour.
__________________________________________________________________________________________________________________________________
UNCRACKED SECTION PROPERTIES SUMMARY
__________________________________________________________________________________________________________________________________
| | Net Precast Section | Transformed Precast Section | Transformed Precast Section |Transformed Composite Section|
| | at Transfer (based on Eci) | at Transfer (based on Eci) | in Service (based on Ec) | in Service (based on Ec) |
| |(include rebar,deduct strand)| (include rebar and strand) | (include rebar and strand) | (include rebar and strand) |
| x | A | I | yb | A | I | yb | A | I | yb | Ac | Ic | ybc |
| m | mm^2 | mm^4 | mm | mm^2 | mm^4 | mm | mm^2 | mm^4 | mm | mm^2 | mm^4 | mm |
__________________________________________________________________________________________________________________________________
| 0.000| 373072 | 13.184E+9 | 318.0| 375058 | 13.257E+9 | 317.0| 375048 | 13.257E+9 | 317.0| 495724 | 34.806E+9 | 434.8|
| 0.115| 384470 | 13.825E+9 | 317.4| 388462 | 13.979E+9 | 315.4| 386152 | 13.855E+9 | 315.7| 507733 | 35.815E+9 | 431.9|
| 0.865| 419416 | 15.885E+9 | 314.2| 432696 | 16.387E+9 | 308.4| 422796 | 15.854E+9 | 309.7| 546331 | 39.155E+9 | 420.9|
| 1.802| 419416 | 15.885E+9 | 314.2| 432696 | 16.387E+9 | 308.4| 422796 | 15.854E+9 | 309.7| 546331 | 39.155E+9 | 420.9|
| 2.739| 419416 | 15.885E+9 | 314.2| 432696 | 16.387E+9 | 308.4| 422796 | 15.854E+9 | 309.7| 546331 | 39.155E+9 | 420.9|
| 3.676| 419416 | 15.885E+9 | 314.2| 432696 | 16.387E+9 | 308.4| 422796 | 15.854E+9 | 309.7| 546331 | 39.155E+9 | 420.9|
| 4.050| 419416 | 15.885E+9 | 314.2| 432696 | 16.387E+9 | 308.4| 422796 | 15.854E+9 | 309.7| 546331 | 39.155E+9 | 420.9|
| 4.613| 419416 | 15.885E+9 | 314.2| 432696 | 16.387E+9 | 308.4| 422796 | 15.854E+9 | 309.7| 546331 | 39.155E+9 | 420.9|
| 4.800| 419416 | 15.885E+9 | 314.2| 432696 | 16.387E+9 | 308.4| 422796 | 15.854E+9 | 309.7| 546331 | 39.155E+9 | 420.9|
| 4.987| 419416 | 15.885E+9 | 314.2| 432696 | 16.387E+9 | 308.4| 422796 | 15.854E+9 | 309.7| 546331 | 39.155E+9 | 420.9|
| 5.550| 419416 | 15.885E+9 | 314.2| 432696 | 16.387E+9 | 308.4| 422796 | 15.854E+9 | 309.7| 546331 | 39.155E+9 | 420.9|
| 5.924| 419416 | 15.885E+9 | 314.2| 432696 | 16.387E+9 | 308.4| 422796 | 15.854E+9 | 309.7| 546331 | 39.155E+9 | 420.9|
| 6.861| 419416 | 15.885E+9 | 314.2| 432696 | 16.387E+9 | 308.4| 422796 | 15.854E+9 | 309.7| 546331 | 39.155E+9 | 420.9|
| 7.798| 419416 | 15.885E+9 | 314.2| 432696 | 16.387E+9 | 308.4| 422796 | 15.854E+9 | 309.7| 546331 | 39.155E+9 | 420.9|
| 8.735| 419416 | 15.885E+9 | 314.2| 432696 | 16.387E+9 | 308.4| 422796 | 15.854E+9 | 309.7| 546331 | 39.155E+9 | 420.9|
| 9.485| 384470 | 13.825E+9 | 317.4| 388462 | 13.979E+9 | 315.4| 386152 | 13.855E+9 | 315.7| 507733 | 35.815E+9 | 431.9|
| 9.600| 373072 | 13.184E+9 | 318.0| 375058 | 13.257E+9 | 317.0| 375048 | 13.257E+9 | 317.0| 495724 | 34.806E+9 | 434.8|
__________________________________________________________________________________________________________________________________
Concise Beam, Version 4.59x, Copyright 2002-2016 Black Mint Software, Inc.
Licensed to: DEFAULT - FOR EVALUATION USE ONLY
Project: SBI MLVP PARKING BLOCK
Problem: INVERT T BEAM
These section properties can used to calculate uncracked concrete stresses using the following guidelines.
Net Precast Section at Transfer properties are used with the initial prestress after transfer (after elastic shortening loss).
Transformed Precast Section at Transfer properties are used with the precast beam self-weight.
Transformed Precast Section in Service properties are used with external loads applied to the non-composite precast beam.
Transformed Composite Section in Service properties are used with external loads applied to the composite precast beam.
__________________________________________________________________________________________________________________________________
note: * Type = LRS - Low-Relaxation Strand, SRS - Stress-Relieved Strand, PB - Plain Bar,
DB - Deformed Bar, SW - Single Wire
** End Types = B - Fully Bonded, D - Debonded, C - Cut, A - Anchored (fully developed)
Calculated Losses: Initial = 5.3%, Final = 6.6%
Maximum Total Prestress Forces: Pj(jacking) = 2592.5 kN,
Pi(transfer) = 2455.5 kN,
Pe(effective) = 2422.4 kN @ x = 4.800 m,
See the "Development Length" text report for details of the strand transfer and development lengths
__________________________________________________________________________________________________________________________________
* End Types: SE - Straight Embeddment, FD - Fully Developed, SH - Standard Hook, HB - Headed Bar
** Offsets are measured up from the bottom or down from the top
See the "Development Length" text report for details of the bar and wire development lengths
__________________________________________________________________________________________________________________________________
SHEAR STIRRUPS
_______________________________________________________________________________________________________
| | | Stirrup| Stirrup| Number of Legs | Total Stirrup Area | Stirrup Spacing |
| From | To | Grade | Size | Stirrup |Interface| Stirrup | Interface | Stirrup |Interface|
| m | m | MPa | | in Beam | Ties | mm^2 | mm^2 | mm | mm |
_______________________________________________________________________________________________________
| 0.000| 2.000| 415| 32mm | 4| 2| 3219.5 | 1609.7 | 50.0| 50.0|
| 2.000| 7.550| 500| 12mm | 4| 2| 452.4 | 226.2 | 100.0| 100.0|
| 7.550| 9.600| 415| 32mm | 4| 2| 3219.5 | 1609.7 | 50.0| 50.0|
_______________________________________________________________________________________________________
__________________________________________________________________________________________________________________________________
TORSION PARAMETERS
Aoh is the area enclosed by the centerline of the outermost closed transverse torsional reinforcement.
Ph is the perimeter of the area defined as Aoh.
__________________________________________________________________________________________________________________________________
____________________________________________________
| Segment/Length | Linear Weight |
| | From | To | Beam | Cast-in-Place |
|No.| m | m | kN/m | kN/m |
____________________________________________________
| 1| 0.000| 9.600| 8.8254 | 3.7184 |
____________________________________________________
__________________________________________________________________________________________________________________________________
Concise Beam, Version 4.59x, Copyright 2002-2016 Black Mint Software, Inc.
Licensed to: DEFAULT - FOR EVALUATION USE ONLY
Project: SBI MLVP PARKING BLOCK
Problem: INVERT T BEAM
|SDL AT | D |SIDL |Vertical: 17.9 kN/m full length |No Load Distribution|
|SDL AT | D |machine |Vertical: 107.5 kN/m full length |No Load Distribution|
|Live Load | L |LL |Vertical: 21.5 kN/m full length |No Load Distribution|
________________________________________________________________________________________________________________
Some applied loads are inactive.
Load Combinations
Factored Combination 1 = 1.40D + 1.40F
Factored Combination 2 = 1.20D + 1.60L + 0.50SRLr + 1.20F
Factored Combination 3 = 1.20D + 1.00L + 1.60SRLr + 1.20F
Factored Combination 4 = 1.20D + 1.60SRLr + 1.20F + 0.50W
Factored Combination 5 = 1.20D + 1.00L + 0.50SRLr + 1.20F + 1.00W
Factored Combination 6 = 1.20D + 1.00L + 0.50SRLr + 1.20F + 1.00W
Factored Combination 7 = 0.90D + 1.00W
Factored Combination 8 = 0.90D + 0.90F + 1.00E
Factored Combination 9 =
__________________________________________________________________________________________________________________________________
ANALYSIS RESULTS SUMMARY - IN SERVICE
__________________________________________________________________________________________
| | Total Unfactored Moments| Total Factored Effects |
| x | Total | Sustained | Shear | | Moment | | Torsion | |
| m | kNm | kNm | kN | [*]| kNm | [*]| kNm | [*]|
__________________________________________________________________________________________
| 0.000| 0.0 | 0.0 | 0.0 |[ 1]| 0.0 |[ 1]| 0.0 |[ 1]|
| 0.115| -1.3 | -1.1 | -28.0 |[ 1]| -1.6 |[ 1]| 0.0 |[ 1]|
| 0.115| -1.3 | -1.1 | 1146.2 |[ 1]| -1.6 |[ 1]| 0.0 |[ 1]|
| 0.865| 633.0 | 563.7 | 963.7 |[ 1]| 789.2 |[ 1]| 0.0 |[ 1]|
| 1.802| 1271.5 | 1132.3 | 735.3 |[ 1]| 1585.2 |[ 1]| 0.0 |[ 1]|
| 2.739| 1738.0 | 1547.8 | 506.4 |[ 1]| 2167.0 |[ 1]| 0.0 |[ 1]|
| 3.676| 2032.3 | 1810.1 | 277.2 |[ 1]| 2534.1 |[ 1]| 0.0 |[ 1]|
| 4.050| 2101.8 | 1872.0 | 185.4 |[ 1]| 2620.8 |[ 1]| 0.0 |[ 1]|
| 4.613| 2154.2 | 1918.8 | 47.6 |[ 1]| 2686.3 |[ 1]| 0.0 |[ 1]|
| 4.800| 2157.9 | 1922.1 | 1.6 |[ 1]| 2690.9 |[ 1]| 0.0 |[ 1]|
| 4.987| 2154.6 | 1919.2 | -44.5 |[ 2]| 2686.9 |[ 1]| 0.0 |[ 1]|
| 5.550| 2103.4 | 1873.7 | -182.4 |[ 1]| 2623.1 |[ 1]| 0.0 |[ 1]|
| 5.924| 2034.7 | 1812.5 | -274.5 |[ 1]| 2537.5 |[ 1]| 0.0 |[ 1]|
| 6.861| 1741.8 | 1551.6 | -505.1 |[ 1]| 2172.3 |[ 1]| 0.0 |[ 1]|
| 7.798| 1275.5 | 1136.3 | -736.0 |[ 1]| 1590.9 |[ 1]| 0.0 |[ 1]|
| 8.735| 635.7 | 566.4 | -967.3 |[ 1]| 792.9 |[ 1]| 0.0 |[ 1]|
| 9.485| -1.3 | -1.2 | -1152.6 |[ 1]| -1.6 |[ 1]| 0.0 |[ 1]|
| 9.485| -1.3 | -1.2 | 28.5 |[ 1]| -1.6 |[ 1]| 0.0 |[ 1]|
| 9.600| 0.0 | 0.0 | 0.0 |[ 1]| 0.0 |[ 1]| 0.0 |[ 1]|
__________________________________________________________________________________________
Concise Beam, Version 4.59x, Copyright 2002-2016 Black Mint Software, Inc.
Licensed to: DEFAULT - FOR EVALUATION USE ONLY
Project: SBI MLVP PARKING BLOCK
Problem: INVERT T BEAM
* Note: actual crack widths can vary by as much as 50% from this estimated value.
Control of cracking is accomplished by proper steel detailing as specified in the design code.
** Note: Gergely & Lutz equation: w = k1 x fs x h2 / h1 x CubicRoot(dc * A)
Suri & Dilger equation: w = k1 x fs x dc x Sqrt(At / Ast)
__________________________________________________________________________________________________________________________________
DEFLECTION ESTIMATE AT ALL STAGES
Design Code Used: ACI 318-11
The beam is SHORED during the cast-in-place pour for the weight of the dead load applied before the cast-in-place pour, and the cast-in-pla
Concise Beam, Version 4.59x, Copyright 2002-2016 Black Mint Software, Inc.
Licensed to: DEFAULT - FOR EVALUATION USE ONLY
Project: SBI MLVP PARKING BLOCK
Problem: INVERT T BEAM
| 4.987| 8.4 | 4.1 | -6.2 | -13.7 | -16.7 | -10.5 | -3.0 | 890 | 3112 |
| 5.550| 8.2 | 4.1 | -5.9 | -13.2 | -16.1 | -10.2 | -2.9 | 919 | 3223 |
| 5.924| 7.9 | 4.0 | -5.6 | -12.5 | -15.3 | -9.7 | -2.8 | 961 | 3382 |
| 6.861| 6.7 | 3.6 | -4.3 | -10.0 | -12.2 | -8.0 | -2.2 | 1174 | 4219 |
| 7.798| 4.7 | 2.8 | -2.6 | -6.6 | -8.1 | -5.5 | -1.5 | 1703 | 6260 |
| 8.735| 2.0 | 1.6 | -1.0 | -2.8 | -3.5 | -2.5 | -0.7 | 3686 | 13695 |
| 9.485| -0.7 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | 0 | 0 |
| 9.600| -1.1 | -0.3 | 0.1 | 0.4 | 0.5 | 0.4 | 0.1 | 584 | 2175 |
_____________________________________________________________________________________________________________
Col. A: Net deflection at transfer includes prestressing and beam weight on temporary supports.
Col. B: Net deflection at erection includes prestressing and all dead loads applied before the cast-in-place
pour plus long-time deflection growth of the prestressing and beam weight up to erection
Col. C: Net deflection at completion of construction includes prestressing and all dead loads
plus long-time deflection growth of the prestressing and dead load up to completion
Col. D: Net DL deflection at final includes prestressing, all dead loads, and sustained live loads,.
plus long-time deflection growth.
Col. E: Net total deflection at final includes prestressing, all dead loads, and all live loads,
plus long-time deflection growth.
Live load includes roof load, and fluid weight. Wind and earthquake are not included.
Deflection growth is estimated by use of the PCI suggested multipliers - see the Deflection Multipliers report.
Concise Beam, Version 4.59x, Copyright 2002-2016 Black Mint Software, Inc.
Licensed to: DEFAULT - FOR EVALUATION USE ONLY
Project: SBI MLVP PARKING BLOCK
Problem: INVERT T BEAM
__________________________________________________________________________________________________________
| | Design | Prestress| Concrete | Strength Provided | Min. Strength Req'd | Notes & |
| | Shear | Component| Strength | Stirrups | Total | Stirrups | Total | Warnings |
| x | Vu | Vp | ØVc | ØVs | ØVn | ØVs | ØVn | |
| m | kN | kN | kN | kN | kN | kN | kN | |
__________________________________________________________________________________________________________
| 0.000| 0.0 | 0.0 | -356.4 | -712.4 | -1069 | 0.0 | -356.4 | 4 5 |
| 0.115| 0.0 | 0.0 | 381.6 | 712.4 | 1094 | 0.0 | 381.6 | 4 5 |
| 0.115| 1014 | 0.0 | 381.6 | 712.4 | 1094 | 631.9 | 1014 | 4 5 |
| 0.865| 963.7 | 0.0 | 592.7 | 773.4 | 1366 | 371.0 | 963.7 | 4 |
| 1.802| 735.3 | 0.0 | 543.3 | 771.1 | 1314 | 192.0 | 735.3 | 4 |
| 2.739| 506.4 | 0.0 | 295.5 | 771.6 | 1067 | 210.9 | 506.4 | 4 |
| 3.676| 277.2 | 0.0 | 166.9 | 771.5 | 938.5 | 110.3 | 277.2 | 4 |
| 4.050| 185.4 | 0.0 | 164.0 | 771.5 | 935.5 | 54.2 | 218.2 | 4 |
| 4.613| 47.6 | 0.0 | 164.0 | 771.5 | 935.5 | 0.0 | 164.0 | 4 |
| 4.800| 1.6 | 0.0 | 164.0 | 771.5 | 935.5 | 0.0 | 164.0 | 4 |
| 4.987| -44.5 | 0.0 | -164.0 | -771.5 | -935.5 | 0.0 | -164.0 | 4 |
| 5.550| -182.4 | 0.0 | -164.0 | -771.5 | -935.5 | -54.2 | -218.2 | 4 |
| 5.924| -274.5 | 0.0 | -164.9 | -771.5 | -936.5 | -109.6 | -274.5 | 4 |
| 6.861| -505.1 | 0.0 | -293.4 | -771.6 | -1065 | -211.6 | -505.1 | 4 |
| 7.798| -736.0 | 0.0 | -541.0 | -771.1 | -1312 | -195.0 | -736.0 | 4 |
| 8.735| -967.3 | 0.0 | -593.7 | -773.4 | -1367 | -373.6 | -967.3 | 4 |
| 9.485| -1018 | 0.0 | -381.6 | -712.4 | -1094 | -636.2 | -1018 | 4 5 |
| 9.485| 0.0 | 0.0 | 381.6 | 712.4 | 1094 | 0.0 | 381.6 | 4 5 |
| 9.600| 0.0 | 0.0 | 356.4 | 712.4 | 1069 | 0.0 | 356.4 | 4 5 |
__________________________________________________________________________________________________________
Notes & Warnings
4 - Note: Shear strength provided by shear steel, ØVs, is limited by maximum limit (web crushing).
5 - Note: Design shear force limited to critical section near support.
Note: The principal web stress is checked for the calculation of Vcw.
__________________________________________________________________________________________________________________________________
TORSION DESIGN CHECK
_________________________________________________________________________________________
| | Design | Threshold| Combined Shear | Torsion Strength | Notes & |
| | Torsion | Torsion | and Torsion | Provided | Required | Warnings |
| x | Tu | ØTcr/4 | Stress | Limit | ØTn | ØTn | |
| m | kNm | kNm | MPa | MPa | kNm | kNm | |
_________________________________________________________________________________________
| 0.000| 0.0 | 24.0 | 0.00 | 0.00 | 0.0 | 0.0 | 2 |
| 0.115| 0.0 | 25.7 | 0.00 | 0.00 | 0.0 | 0.0 | 2 |
| 0.115| 0.0 | 25.7 | 0.00 | 0.00 | 0.0 | 0.0 | 2 |
| 0.865| 0.0 | 34.8 | 0.00 | 0.00 | 0.0 | 0.0 | |
| 1.802| 0.0 | 35.9 | 0.00 | 0.00 | 0.0 | 0.0 | |
| 2.739| 0.0 | 36.7 | 0.00 | 0.00 | 0.0 | 0.0 | |
| 3.676| 0.0 | 37.2 | 0.00 | 0.00 | 0.0 | 0.0 | |
| 4.050| 0.0 | 37.3 | 0.00 | 0.00 | 0.0 | 0.0 | |
| 4.613| 0.0 | 37.4 | 0.00 | 0.00 | 0.0 | 0.0 | |
| 4.800| 0.0 | 37.4 | 0.00 | 0.00 | 0.0 | 0.0 | |
| 4.987| 0.0 | 37.4 | 0.00 | 0.00 | 0.0 | 0.0 | |
| 5.550| 0.0 | 37.3 | 0.00 | 0.00 | 0.0 | 0.0 | |
| 5.924| 0.0 | 37.2 | 0.00 | 0.00 | 0.0 | 0.0 | |
| 6.861| 0.0 | 36.7 | 0.00 | 0.00 | 0.0 | 0.0 | |
| 7.798| 0.0 | 35.9 | 0.00 | 0.00 | 0.0 | 0.0 | |
| 8.735| 0.0 | 34.8 | 0.00 | 0.00 | 0.0 | 0.0 | |
| 9.485| 0.0 | 25.7 | 0.00 | 0.00 | 0.0 | 0.0 | 2 |
| 9.485| 0.0 | 25.7 | 0.00 | 0.00 | 0.0 | 0.0 | 2 |
| 9.600| 0.0 | 24.0 | 0.00 | 0.00 | 0.0 | 0.0 | 2 |
_________________________________________________________________________________________
Notes & Warnings
2 - Note: Design torsion force limited to critical section near support.
__________________________________________________________________________________________________________________________________
SHEAR/TORSION TRANSVERSE REINFORCING DESIGN CHECK
Concise Beam, Version 4.59x, Copyright 2002-2016 Black Mint Software, Inc.
Licensed to: DEFAULT - FOR EVALUATION USE ONLY
Project: SBI MLVP PARKING BLOCK
Problem: INVERT T BEAM
_____________________________________________________________________________________________________________
| |Horizontal| Strength | Required | Tie Size | Spacing | Spacing | Strength | Strength | Notes & |
| | Shear | with no | Ties | Provided | Required | Provided | Required | Provided | Warnings |
| x | Vu | ties | Av/s | Av | s | s | ØVnh | ØVnh | |
| m | kN | kN | mm^2/m | mm^2 | mm | mm | kN | kN | |
_____________________________________________________________________________________________________________
| 0.000| 0.0 | 93.0 | 0 | 1610 | 0.0 | 50.0 | 0.0 | 4795 | 3 |
| 0.115| 0.0 | 93.3 | 0 | 1610 | 0.0 | 50.0 | 0.0 | 4810 | 3 |
| 0.115| 1014 | 93.3 | 4336 | 1610 | 371.3 | 50.0 | 1014 | 7513 | 1 4 5|
| 0.865| 963.7 | 92.7 | 4150 | 1610 | 387.9 | 50.0 | 963.7 | 7462 | 1 4 5|
| 1.802| 735.3 | 92.4 | 3173 | 1610 | 507.2 | 50.0 | 735.3 | 7440 | 4 5|
| 2.739| 506.4 | 92.5 | 1484 | 226.2 | 152.4 | 100.0 | 506.4 | 614.3 | 4 |
| 3.676| 277.2 | 92.5 | 250 | 226.2 | 904.8 | 100.0 | 335.2 | 614.3 | |
| 4.050| 185.4 | 92.5 | 250 | 226.2 | 904.8 | 100.0 | 335.2 | 614.3 | |
| 4.613| 47.6 | 92.5 | 0 | 226.2 | 0.0 | 100.0 | 47.6 | 614.3 | 3 |
| 4.800| 1.6 | 92.5 | 0 | 226.2 | 0.0 | 100.0 | 1.6 | 614.3 | 3 |
| 4.987| -44.5 | -92.5 | 0 | 226.2 | 0.0 | 100.0 | -44.5 | -614.3 | 3 |
| 5.550| -182.4 | -92.5 | 250 | 226.2 | 904.8 | 100.0 | -335.2 | -614.3 | |
| 5.924| -274.5 | -92.5 | 250 | 226.2 | 904.8 | 100.0 | -335.2 | -614.3 | |
| 6.861| -505.1 | -92.5 | 1475 | 226.2 | 153.4 | 100.0 | -505.1 | -614.3 | 4 |
| 7.798| -736.0 | -92.4 | 3177 | 1610 | 506.7 | 50.0 | -736.0 | -7440 | 4 5|
| 8.735| -967.3 | -92.7 | 4166 | 1610 | 386.4 | 50.0 | -967.3 | -7462 | 1 4 5|
| 9.485| -1018 | -93.3 | 4354 | 1610 | 369.7 | 50.0 | -1018 | -7513 | 1 4 5|
| 9.485| 0.0 | 93.3 | 0 | 1610 | 0.0 | 50.0 | 0.0 | 4810 | 3 |
| 9.600| 0.0 | 93.0 | 0 | 1610 | 0.0 | 50.0 | 0.0 | 4795 | 3 |
_____________________________________________________________________________________________________________
Notes & Warnings
1 - WARNING: Amount of tie steel required is unattainable due to maximum limit.
3 - Note: No ties required.
4 - Note: Ties required represent minimum requirement.
5 - Note: Shear resistance based on shear friction.
__________________________________________________________________________________________________________________________________
HORIZONTAL SHEAR DESIGN CHECK BY MOMENT REGION
Design Code Used: ACI 318-11
* Required ties should be distributed in proportion to distribution of shear force (or stirrups).