BOLT
Ultimate strength of the bolt,fu = 800 N/mm2
Yield strength of the bolt,fy = 640 N/mm2
Young's modulus, E = 208000 N/mm2
Bolt Type = 8.8
Nominal tensile Stress = 600 N/mm2 AISC Table J3-2
Nominal Shear Stress = 320 N/mm 2
AISC Table J3-2
Min Bolt pretension = 205000 N AISC Table J3-1M
Assumed bolts = 8
Asuumed bolts in one row = 2
bolt diameter, d = 24 mm
Hole Dia, h = 26 mm AISC Table 3.3 M
Spacing, s = 72 mm 2.67 or 3 times bolt diameter
thickness of connected part = 16 mm Governs
Width of gusset plate = 300 mm
Thickness of web = 16 mm
flange thickness = 19 mm
Area of Bolt, Ag = 452.3904 mm^2 π
Plate area - area
* diameter^2 / 4 of bolts, in
Net area in Shear, Anv = 3968 mm^2 cross-section
Gross area subjected to shear ,Agv = 4800 mm^2 plate area - area of bolts, in
Plate c/s
Net area subjected to tension, Ant = 3968 mm^2 cross-section
Minimum Edge distance = 50 mm AISC J3-4M, gives 34mm
Edge Bolt Clear distance, Lc = 37 mm
Non-edge bolt clear distance, Lc = 48 mm
Axial Force acting on bolt group = 91321 N Input depends on force acting on
Shear Force acting on bolt group = 481165 N bolt, not member
Moment,, M = 105 KN-M
D, depth of minimum section = 300 mm
Max Axial force due to self weight only, = 14955 N
AISC Eq J3-2
Combined Tension and Shear = F'nt*Ab/Ω 120046 > 71561 OK
F'nt = 1.3*Fnt - Ω*Fnt * fv/Fnv AISC Eq J3-3b
fv, reqd shear stress = 66 N/mm2
Adjusted tensile stress F'nt , < Fnt = 531 N/mm2
CONNECTED ELEMENTS
Yield and ultimate strengths of plate are to be used
Compression Check
r = sqrt(I/A) AISC section J4-4
For UPN200, A = 64.4 cm^2. I = 3620 Cm^4
KL/r, 1*3000/77.02 = 39.0 > 25
4.71 * sqrt(E/fy) = 115.6 use AISC Chapter E
If, KL/r < 4.71 * sqrt(E/fy), Fcr = Fy * 0.658^(Fy/Fe) AISC Eq E7-2
AISC J6- Other types of splices in cross sections of plate girders and beams shall develop the
strength required by the forces at the point of the splice. Due to non-availability of detailed design
procedure in AISC codes for bolted splices, British Standard codes are used
Check 1
Flange cover plate
Min length of cover plate on each min of flange width and 225mm
column, Lfp = 300
Minimum width of flange cover plate, flange width - thickness of flange - two times
Wfp = 248 thickness of gusset plate
Min thickness of flange cover plate,
Tfp = 10 min of half of flange thickness and 10 mm
If Moment, M < F*D/2, net tension doesnot occur
Moment, M = 105000000
Fcd is max axial force due to factored self weight only.
Fcd *D /2 = 86915469 Fcd value obtained from STAAD
here, M is greater than Fcd *D /2 Must check for net tension