Anti-Graffiti Coating ®
Features Benefits
■■ Costsavings of 25% to 40% compared to existing methods of
■■ Graffiti
removal with just water
repainting, chemical removal, or abrasive cleaning.
■■ Non-Sacrificial
■■ Can be cleaned an unlimited amount of times.
■■ Weatherability
■■ Preserves its aesthetic appearance throughout lifetime.
■■ Single component
■■ Ready to brush, roll, or spray. No mixing multiple components.
■■ Elastomeric
■■ Expands and contracts with the substrate — no adhesion issues.
■■ Low VOC
■■ Long term cost savings.
■■ Long service life —10–15+ years
■■ Apply over concrete, steel, or previously painted surfaces.
■■ Surface tolerant
■■ Saves labor and time.
■■ One coat application
Recommended Uses
■■ Interior
or Exterior Applications ■■ TransitStations
■■ Previously Painted Concrete or Steel Surfaces ■■ Overpasses
Coatings NOTE: Brush or roll application may require multiple coats to graffiti remove
achieve maximum film thickness and uniformity of appearance.
• Excellent graffiti resistance • Bridge Abutments B97C150 Fast Drying
• Excellent cleanability with either water power-washing, or solvent • Commercial Buildings
Drying Schedule @ 10.0 mils wet (250 microns): Non-Sacrificia
wipe • Schools @ 40°F/4.5°C @ 77°F/25°C @ 120°F/49°C Excellent Clea
• UV resistanceRevised: January 24, 2013 • Transit Stations 9.54
50% RH
• Excellent adhesion • OverpassesTo touch: 9 hours 1 hour 30 minutes Test Name
• Low VOC PRODUCT DESCRIPTION • RailcarsTack free: R
12ECOMMENDED
hours USES
4 hours 1 hour
• Fast drying
ANTI-GRAFFITI COATING is a one-component, non-sacrifi • New
cial, Construction
To cure:
Uses: 21 days 7 days 4 days
• Outstanding airless spray properties
ready-to-use siloxane coating that cures with atmospheric moisture. •Drying time interior
Use over is temperature, humidity,
or exterior and surface
concrete film thickness dependent.
that needs protec-
• Single component
Product Characteristics
Intended for use over properly prepared concrete surface. tion from
Shelf Life:graffiti defacing 12 months, unopened Accelerated
Store indoors at 40°F (4.5°C) to Weathering
PRODUCT
• Excellent graffitiCresistance
HARACTERISTICS PERFORMANCE
• Bridge Abutments CHARACTERISTICS 100°F (38°C)
Finish: • Excellent cleanability with either water power-washing, or solvent
Semi-Gloss •Flash
Performance: Commercial
Point: Buildings >100°F (38°C), TCC
wipe Passed 4000•Reducer/Clean
Schools
hours of QUVUp: / multi-graffitiMineral
application and
Spirits - up to 5% as Adhesion
Color: • UV resistance Clear removal • Transit Stations needed for spray application
• Excellent adhesion • Overpasses
Clean Up: Mineral Spirits or Naphtha
• Low VOC
Volume Solids: 72% ± 2% • Railcars
Gloss retention = 63%
• Fast drying • Newchange
Color Construction
<3 delta E CIE *L a b
• Outstanding airless
Weight Solids: 75% spray
± 2% properties
• Single component No signs of graffiti left after clean-up; no visible signs of streaking,
www.sherwin-williams.com/protecti
VOC (EPA Method 24): <250 g/l; 2.1 lb/gal cracking,Performance
pinholing, discoloration Characteristics
or other coating degradation upon
PRODUCT CHARACTERISTICS casual examination PERFORMANCE CHARACTERISTICS
Recommended
Finish: Spreading Rate per coat:
Semi-Gloss Performance:
Minimum Maximum Passed 4000 hours of QUV / multi-graffiti application and
Color: Clear Graffiti Removal
removal from Surface Coated:
Wet mils (microns) 8.0 (200) 12.0 (300)
Power wash with 3000-psi pressure washer (25 feet of hose) having
Dry mils (microns) 6.0 (150) 9.0 (225)
Volume Solids: 72% ± 2% a 15-degree tip at Gloss
2-3 inches away
retention = from
63% the surface.
~Coverage sq ft/gal (m2/L) 128 (3.1) 192 (4.7)
Theoretical coverage sq ft/gal
Color change <3 delta E CIE *L a b
(m2/L) @ 1Weight
mil / 25Solids:
microns dft 1152
75%(28.2)
± 2% Graffiti can also be removed by solvent wiping or acceptable
NOTE: Brush or roll application may require multiple coats to No signs of graffiti left after clean-up; no visible signs of streaking,
graffiti removers.
achieve VOC
maximum(EPAfiMethod 24):and<250
lm thickness g/l; 2.1
uniformity of lb/gal
appearance. cracking, pinholing, discoloration or other coating degradation upon
Fast Dryingcasual examination
Drying Schedule @ 10.0 mils
Recommended Rate per coat: Non-Sacrificial
wet (250 microns):
Spreading
@ 40°F/4.5°C @ 77°F/25°C @ 120°F/49°C
Minimum Excellent Cleanability
Maximum
50% RH 8.0 (200) Graffiti Removal from Surface Coated:
Wet mils (microns) 12.0 (300)
To touch:Dry mils 9(microns)hours 1 hour 6.0 (150) 30 minutes9.0 (225)
Test Name PowerTest
wash with 3000-psi pressure washer
Method Results(25 feet of hose) having
Tack free:~Coverage 12 hours 4 hours 1 hour a 15-degree tip at 2-3 inches away from the surface.
sq ft/gal (m2/L) 128 (3.1) 192 (4.7)
To cure: Theoretical 21coverage
days 7
sq ft/galdays 4 days
Drying time(mis2/L)
temperature, humidity,
@ 1 mil / 25 micronsand 1152 (28.2)
dft film thickness dependent. Graffiti• ASTM
can alsoD4587,
be removed <3.0 DE color change,
QUV-A, by solvent wiping or acceptable
4,000 hours CIE *L a b; 63% gloss
NOTE: Brush or roll application may require multiple coatsAccelerated
to graffiti removers.
Shelf Life: achieve maximum film12 months,and unopened of appearance. • Xenon Arch, 2,000 hours retention
thickness
Store indoors atuniformity
40°F (4.5°C) to Weathering
100°F (38°C) Fast Drying
Drying Schedule @ 10.0 mils wet (250 microns): Texascial
Non-Sacrifi DOT - Graffiti
Pass
Flash Point: >100°F (38°C), TCC Removal Testing
@ 40°F/4.5°C @ 77°F/25°C @ 120°F/49°C Excellent Cleanability
Reducer/Clean Up: Mineral Spirits - up to 5% as Adhesion ASTM D6677 Passes, Rating 8
needed for spray 50%application
RH
To touch: 9 hours 1 hour 30 minutes Test Name Test Method Results
Clean Up:Tack free: 12 Mineral
hours Spirits4or Naphtha
hours 1 hour
To cure: 21 days 7 days 4 days
• ASTM D4587, QUV-A, <3.0 DE color change,
Drying time is temperature, humidity, and film thickness dependent.
4,000 hours CIE *L a b; 63% gloss
Accelerated • Xenon Arch, 2,000 hours retention
Shelf Life: 12 months, unopened
Weathering
Store www.sherwin-williams.com/protective
indoors at 40°F (4.5°C) to continued on back
100°F (38°C)
Texas DOT - Graffiti
Flash Point: >100°F (38°C), TCC Pass
A complete line of products. Market expertise. On-time distribution. Removal Testing
What elseReducer/Clean Up:
would you expect from aMineral
worldSpirits
needed leader
for
- up to 5% as
in protective coatings
spray application
Adhesion and linings?
ASTM D6677 Passes, Rating 8