Bolt A 325
3
fy = 635 Mpa (Yield Stress) Sx = 1618353 mm
σ = 423.33 Mpa
τ = 140 Mpa (allowable shear stress) M = fy x Sx = 388404720 Nmm
N
σ tu = 444 Mpa (allowable bearing stress) Q = 0.4 x tw x (d-2tf) ##
σ ta = 381 Mpa (allowable tension) N = ##
Actual Loads
Q = 826393 N (Actual shear Load)
N = 0N (Actual axial load)
Ag = 1/4 π D2 = 490.8594 mm
2
(cross section area of bolt)
τ = P / n Ag
= 120.2584 Mpa < τ OK! 1
Bolt A 325
fy = 635 Mpa (Yield Stress) M = #
σ = 423.33 Mpa Q = 0.4 x tw x (d-2tf) = 364608 N
τ = 140 Mpa (allowable shear stress) N = #
σ tu = 444 Mpa (allowable bearing stress)
σ ta = 381 Mpa (allowable tension)
Actual Loads
Q = 364608 N (Actual shear Load)
N = 0N (Actual axial load)
A325 14M-25
A325 6M-25
PILE BEARING CAPACITY CALCULATION
Maximum reaction from upper steel structure based on service load combinations is in the table
below.
Below is the calculation for bored pile foundation using Reese and Wright Method
BH : 1
Diameter (B) : 0.35 m SF Skin friction 3
Perimeter (p) : 1.100 m SF End bearing 3
Area (Ap) : 0.096 m2
Inertia (I) : 0.001 m4
cu φ qp fs Fs Qp Qult Qall
Kedalaman (m) Soil N-SPT
(kPa) (kPa) (kPa) (kN) (kN) (kN) (ton)
Data NSPT
0 1 Clay 13 78 702 42.9 47.17 67.51 114.68 3.82
1 3 Clay 14 84 756 46.2 148.77 72.70 221.47 7.38
3 5.1 Clay 22 132 1188 72.6 316.41 114.24 430.65 14.35
5.1 8 Sand 19 30 1092.5 36.80 433.75 105.06 538.81 17.96
8 10 Clay 35 210 1890 115.5 687.75 181.75 869.50 28.98
Data CPT
0 1 Clay 3 18 162 9.9 10.89 15.58 26.46 0.88
1 3 Clay 8 48 432 26.4 68.94 41.54 110.48 3.68
3 5.1 Clay 14 84 756 46.2 175.62 72.70 248.32 8.28
5.1 8 Sand 12 30 690 36.80 292.97 66.35 359.32 11.98
8 10 Clay 35 210 1890 115.5 546.97 181.75 728.71 24.29
Based on the pile reaction and pile bearing calculation, the summary is as follows :
1. The pile bearing capacity = 23 ton > pile reaction = 20.2 ton
2. The pile uplift capacity = 14 ton > pile reaction = 6.4 ton
3. The pile lateral capacity = 15 ton > pile reaction 1.3 ton
160 D13-150
Bored pile
350 350 mm
600
350 D16-150
350
L= 10000
6 D13
D10-100 spiral
CRANE 5 TONNE CAPACITY
Bolt A 325
3
fy = 635 Mpa (Yield Stress) Sx = 1295318 mm
σ = 423.33 Mpa
τ = 140 Mpa (allowable shear stress) M = fy x Sx = 310876320 Nmm
N
σ tu = 444 Mpa (allowable bearing stress) Q = 0.4 x tw x (d-2tf) ##
σ ta = 381 Mpa (allowable tension) N = ##
Actual Loads
Q = 740181.7 N (Actual shear Load)
N = 0N (Actual axial load)
Ag = 1/4 π D2 = 490.8594 mm
2
(cross section area of bolt)
τ = P / n Ag
= 125.6649 Mpa < τ OK! 1
Bolt A 325
fy = 635 Mpa (Yield Stress) M = #
σ = 423.33 Mpa Q = 0.4 x tw x (d-2tf) = 323136 N
τ = 140 Mpa (allowable shear stress) N = #
σ tu = 444 Mpa (allowable bearing stress)
σ ta = 381 Mpa (allowable tension)
Actual Loads
Q = 323136 N (Actual shear Load)
N = 0N (Actual axial load)
Maximum reaction from upper steel structure based on service load combinations is in the table
below.
Below is the calculation for bored pile foundation using Reese and Wright Method
Below is the pile lateral capacity calculated with L Pile
Based on the pile reaction and pile bearing calculation, the summary is as follows :
1. The pile bearing capacity = 9.9 ton > pile reaction = 8.8 ton
2. The pile uplift capacity = 6 ton > pile reaction = 0.5 ton
3. The pile lateral capacity = 15 ton > pile reaction 0.28 ton
160 D13-150
Bored pile
350 350 mm
600
350 D16-150
350
L= 6000
6 D13
D10-100 spiral