(http://twi
tter.com/
UEntryTes
t)
Physics:
11) Light with energy E is incident upon a surface area (A) per unit time (T). Simplify the units for E/(A*t).
12) What is energy of a 600 nm red light photon?
13) What is orbital speed of a satellite at the height of 8000 km above earth where value of g=6.2 m/s2?
14) What is the angle between equipotential lines and electric eld lines? (parallel, orthogonal, acute, obtuse)
15) U23592 absorbs a neutron and emits two β particles. What will be the daughter element?
16) What quantity does change when a light ray re ects from a mirror
(frequency, wavelength, speed, phase)
17) Divergence of y2i + xz2j+2xk.
http://uentrytest.blogspot.com/2015/06/pieas-ms-test-2014-questions.html 1/12
5/23/2018 PIEAS MS Test 2014 Questions | Entrytest Prep. and Admission Help
18) If a light ray propagates in direction of x-axis. In which plane is movement of its electric eld? (Y-axis, X-axis, XY
plane, YZ plane)
19) The transverse wave nature of light is con rmed by which phenomenon (interference, diffraction, polarization,
refraction)
20) What is the best approximate for diameter of alpha particle (10-9,10-10, 10-12, 10-11)
Mathematics:
29) Find Eigen values of a given 3*3 matrix.
(This question repeats almost each year)
30) What maximum volume rectangle can be formed by a rectangular piece of 21*16 inch by cutting a square piece
from each corner? What is area of that square?
31) A drum contains 100 gallons of salt solution with 1 lb/gallon salt. If 2 lb/gallon solution is added at the rate of 5
gallons/min and stirred uniformly and solution is ejected out at the same rate. What time will it require to reach
150 lb salt in solution?
32) If f(x,y) = ex. Sin(xy) the what is the relation b/w and
33) Evaluate
34) What is integrating factor in y’ + y/x = ex
35) How many word can be formed by letters of ALLANAMOPIA with no two A’s adjacent to each other.
The given series is (divergent, in-
determinate, convergent, power series)
37) Pressure at the sea level is 100 kPa. Water density is 1020 kg/m3. At what depth the pressure will be 110 kPa.
(11m, 10m, 9.8m, 1m)
38) A function f(x,y)={(1,x), (2,y), (3,x), (4,y)} is a (an) (Surjective, bijective, 1-1, onto) function.
39) What is the surface area of a unit cube?
40) Value of a variable k was to be found in terms of pi in a math question.
v Subject Part
(Electrical/Electronics):
Power:
= ? (load factor, diversity factor,
plant factor)
http://uentrytest.blogspot.com/2015/06/pieas-ms-test-2014-questions.html 2/12
5/23/2018 PIEAS MS Test 2014 Questions | Entrytest Prep. and Admission Help
42) Potential at the ends of a transmission line is 132 kV, reactance of line is 50 ohm. What is approximate loading
capacity of line?
43) Breakdown voltage strength of air depends upon (voltage applied, air density, humidity, all of these)
44) Receiving and sending end voltage at the ends of a short transmission line are 120<-50 and 100<00 respectively.
Reactance of line is 1+j5. Calculate real power line losses?
45) IGBT combines the good characteristics of ___________ and ___________ 46) A 500 kV, 60 Hz transmission line has
inductance 0.4 mH/km and capacitance 0.02 uF/km. Find the surge impedance of line.
47) Which power plant will always be used as a base load power plant? (coal, diesel, nuclear, hydro-electric)
48) Which motor is not self-starting? (induction, stepper, synchronous, none)
49) What is the effect of increasing rotor resistance on torque of 3 phase wound rotor induction motor? (increases,
decreases, remains same, none) Controls & Communication Systems:
50) For a stable system, what should be values of phase & gain margins
(opposite, both positive, PM –ve & gain margin +ve, both are same) 51) Y=6.x(t)+4 Is this system Linear &
time invariant?
52) The phenomena of Coding and Width allocation is associated with (PAM, PCM, PWM, PPM)
53) Find inverse Laplace of
54) Fourier transform of an even periodic function contains (sine components, cosine components, both, none of
them).
55) x[n] and x[n-1], their Fourier Magnitude & Phase Plots are same or different?
56) A carrier of 2 kHz modulates a signal with frequency deviation 5 kHz, what’s the frequency of modulated signal?
57) What is hamming distance between two binary numbers (011011 &
110001)? (3,2,1,4)
I could remember only 80 questions out of 100. If anyone who appeared in the test does have any more questions not
included above, send them to me! The question order is jumbled, the questions of Subject Part weren’t classi ed in
subcategories in the actual test.
So, how was the test? Seemed a little dif cult to me at very rst. Some questions were knavish, many were
irrelevant to Power Engineering and no doubt some were easy too! But overall test was satisfactory (to many) including
the General Portion. If you can attempt ~40% questions right now, you’re expected to attempt 75%+ questions with
proper preparation.
More than 60% questions are numerical types and calculation based that’s why a non-programmable scienti c
calculator is allowed in the test (The calculator is much helpful in the test, much more than you imagine, bring an
original scienti c calculator with natural display, download its user manual from its site and read the complete
manual, the one/two hour(s) you spend on reading the calculator manual will help you save time and earn extra marks
during the test). I solved about 4-5 questions using advanced natural display calculator which I couldn’t have solved
with a simple scienti c calculator or if solved with simple scienti c calculator would have taken me twice or thrice more
time!
What to prepare for the test? Preparing irrelevant subject matter for years will have no practicable effect on
your test results. Try to be focused, prepare well, and try to avoid far- ung rote learning. Here are the outline of the Test
as supplied by PIEAS:
http://uentrytest.blogspot.com/2015/06/pieas-ms-test-2014-questions.html 4/12
5/23/2018 PIEAS MS Test 2014 Questions | Entrytest Prep. and Admission Help
The question paper is divided into two parts i.e. Part (A) and (B). There will be 50 questions in Part (A) and 50
Questions in Part (B). Part (A) is the general part to be attempted by all the candidates (except MBBS/Medical Sciences
students) whereas Part (B) is the subject part having subject papers. Only the subject paper relevant to the candidate’s
academic background may be attempted by the candidate. The candidate should mention the subject paper he/she is
attempting by lling the appropriate section of the answer sheet. The maximum time allowed is 3 hours. Each question
carries 3 marks and 1 mark will be deducted for a wrong answer.
Physics: Go through all the chapter of Physics F.Sc Part 1 and Part 2 books. Learn all the formulas and be good
with calculations. Last 3,4 chapters of 2nd year Physics are important.
English: English has nothing to prepare, because no speci ed course can be allotted for English preparation. This
is the rst portion of the General test consisting of 10 questions. 1st two are from comprehension, so they are easy. Next
3-4 are synonyms & antonyms, they’re easy too but confusing, tick them carefully.
And remaining questions are correct form of verbs, prepositions or correction of grammar mistakes. Subject
Preparation:
Basic Electrical Engineering: Revise Circuit Analysis I & II from David Irwin’s book or any other Basic Circuit
Analysis book (1st order & 2nd order circuits are important). Review EMT from William H. Hayt’s Book or Alexander
Sadiko’s. Learn all basic equations (i.e. Maxwell’s, Poisson, Laplace, Ampere, Green/Stokes Theorems etc.). Have a basic
http://uentrytest.blogspot.com/2015/06/pieas-ms-test-2014-questions.html 5/12
5/23/2018 PIEAS MS Test 2014 Questions | Entrytest Prep. and Admission Help
review of DLD book by Thomas L. Floyd. Pay special attention to combinational logic circuits (They’re important). Have an
insight of sequential logic. You may skip K-maps and other lengthy portions.
Electronics, Electronic Circuits and Components: For this portion, prepare thoroughly Electronic Circuit &
Devices by Robert T. Paynter or Thomas Floyd’s Electronic Devices. FET, JFET and MOSFET’s components, circuits, biasing
and analysis is REALLY important. Learn them by heart (in fact brain :P).
Controls and Communications Systems: For control systems, review Control System by Norman S. Nice. (Samarajit
Ghosh’s book is not up to standard). Revise basics of Open loop & Feedback Control systems. Stable & Un-Stable system
conditions, poles-zeros plots, bode plots, frequency response, Phase margin, gain margin, root locus and all basic
relevant topics.
Communication Systems: (Advance topics from this portion are asked in test) Prepare Laplace & Fourier transforms
(important). Harmonics, AM & FM modulation techniques, Slew rate, Fourier magnitude & phase plots, lters (IIR & FIR).
You may refer to Modern Digital & Analog Communication Systems by B. P. Lathi. Also review topics from Signal & Systems
and DSP. Prepare basics (i.e. LTI systems, signals & their properties, convolution, Fourier series & transform plots of a
signal etc.)
Power: Prepare AC & DC machines from chapman. Revise selective topics of Power Engineering from Principals of
Power Systems by V.K Mehta. Power calculations are very important (i.e. nding base values, Impedances, Real & Reactive
power owing through a circuit, capacitance & inductance values). Revise
Power generation too (it’s important). Also revise Power Electronics topics especially for SCR, IGBT, MOSFET, BJT,
DIODES, TRIACS & DIACS; their properties, construction, circuits & applications.
This is the complete course outline for M.S fellowship test. But you must prepare more than that mentioned above in
order to succeed. By carefully observing the 2014 test questions, you may nd out the exact (But up to a limited
accuracy) topics to prepare for a speci c subject for coming year’s test. For example from Circuit Analysis, questions of
Series Parallel combination of Resistors, 1st order & 2nd order circuits, Maximum Power transfer theorem, Basic
Current/Voltage division, KCL, KVL are much important because questions related to these topics have been found in
Fellowship tests. For instance, at least 3 questions were related to FET, JFET, & MOSFET as listed in above questions, so
this is most important topic! Same is true for Op-Amp.
Carefully read the sample paper; also search Internet for past papers for PIEAS B.S and M.S fellowship tests (2010,
2011, 2012 & 2013; 2014 is given above). At least 3-4 questions (or may more) are from past papers. And many more or
related to past paper questions with just small changes in values etc.!
How much time should you allot for test preparation? The answer to this question is quite important for an
aspirant candidate to succeed. The time you set aside for your test preparation depends on a number of factors; you
have to ask a couple of questions to yourself:
http://uentrytest.blogspot.com/2015/06/pieas-ms-test-2014-questions.html 6/12
5/23/2018
So, scrutinize each subject andPIEAS MS Test 2014 Questions | Entrytest Prep. and Admission Help
its sub-topics according to Previous Knowledge, Type of Revision etc. and you
may be able to allocate speci c time for each subject. Manage your time well and you may be able to revise a lot of
material in shorter time span! :) For just to take an example, I completed my revision in 4-5 days from 04 June, 2014 to
08 June, 2014. I revised only F.Sc Maths and Physics books, because I had left with no time for Subject Preparation (as
8th semester’s nals started from 10th June). Then I got one and half day more after 2nd paper of nals. I again reviewed
Maths & Physics one time and looked upon some topics from engineering subjects. That was all of my preparations!
Attempting a MCQs based test is itself an art. Mastering that art with a proper commingle of preparation will get
you through any test. You’ve 3 hours and 100 MCQs; spend each second of available time wisely. In the rst round,
attempt only easiest question which you can solve in less than 30 seconds. Then in the next round try moderate
questions. And in the last, attack the Hard questions, answer those which you can easily solve, don’t spend a lot of time
on a single questions. Use your Brain & Calculator collectively.
Read the question and its answer choices carefully, now relate each answer choice to the question and nd the
chances for this choice to be a correct answer. Use the techniques of reverse solving, inference from other option, use
analogies and make a decision that the choice being considered can be an answer or not. Similarly, work out all the
option choices and each time roll out the choice which has no (or relatively lesser) chance to be a correct answer and
this way you may increase the probability for guessing a correct answer.
If 4 multiple choices are given for a question then you have 25% (1/4) probability of guessing a correct answer
randomly. If you eliminate one choice then you’ve 33% chance and if you eliminate two answer choices your correct
guessing chance rises up to 50% and so on.
I answered 98 questions. About 15 of them were educated guesses, 70+ were correct (according to me), so I expect
to get 220+ marks out of 300. I think 200 marks are enough for a candidate to be shortlisted for the interview!
Muhammad Zeeshan ()
I am Mechatronics and Control Engineer from UET, Lahore. Helping Engineering students gives me pleasure.
(https://www.facebook.com/muhammadzeeshan1992) (https://twitter.com/mzeeshan0506)
(http://#.tumblr.com/)
http://uentrytest.blogspot.com/2015/06/pieas-ms-test-2014-questions.html 7/12
5/23/2018 PIEAS MS You Might
Test 2014 Also| Entrytest
Questions Like Prep. and Admission Help
(http://uentrytest.blogspot.com/2015/ (http://uentrytest.blogspot.com/2015/
06/pieas-ms-interview-chronicle.html) 06/important-mcqs-for-pieas-entry-
PIEAS MS Interview Chronicle test.html)
(http://uentrytest.blogspot.com/2015/06 Important MCQ's for PIEAS Entry
/pieas-ms-interview-chronicle.html) Tes...
(http://uentrytest.blogspot.com/2015/06
/important-mcqs-for-pieas-entry-
test.html)
10 comments:
Reply
Replies
Yes
very nice...
Reply
Reply
Replies
Last time when i applied for PIEAS fellowship,there wasn't any negative marking.
Reply
Reply
Reply
Reply
Reply
(https://www.blogger.com/comment-iframe.g?
blogID=9219802133171148734&postID=7347548731905556497&blogspotRpcToken=8213820)
http://uentrytest.blogspot.com/2015/06/pieas-ms-test-2014-questions.html 9/12
5/23/2018 PIEAS MS Test 2014 Questions | Entrytest Prep. and Admission Help
Popular Posts
Labels
Admissions (Http://Uentrytest.Blogspot.Com/Search/Label/Admissions)
Chemistry I (Http://Uentrytest.Blogspot.Com/Search/Label/Chemistry%20I)
Chemistry II (Http://Uentrytest.Blogspot.Com/Search/Label/Chemistry%20II)
http://uentrytest.blogspot.com/2015/06/pieas-ms-test-2014-questions.html 10/12
5/23/2018 PIEAS MS Test 2014 Questions | Entrytest Prep. and Admission Help
Chemistry Notes (Http://Uentrytest.Blogspot.Com/Search/Label/Chemistry%20Notes)
Chemisty (Http://Uentrytest.Blogspot.Com/Search/Label/Chemisty)
Educator (Http://Uentrytest.Blogspot.Com/Search/Label/Educator)
Engineering (Http://Uentrytest.Blogspot.Com/Search/Label/Engineering)
English (Http://Uentrytest.Blogspot.Com/Search/Label/English)
FYP (Http://Uentrytest.Blogspot.Com/Search/Label/FYP)
Mathematics I (Http://Uentrytest.Blogspot.Com/Search/Label/Mathematics%20I)
Mathematics II (Http://Uentrytest.Blogspot.Com/Search/Label/Mathematics%20II)
MCAT (Http://Uentrytest.Blogspot.Com/Search/Label/MCAT)
Microcontroller (Http://Uentrytest.Blogspot.Com/Search/Label/Microcontroller)
NTS (Http://Uentrytest.Blogspot.Com/Search/Label/NTS)
NUST (Http://Uentrytest.Blogspot.Com/Search/Label/NUST)
Physics (Http://Uentrytest.Blogspot.Com/Search/Label/Physics)
Physics I (Http://Uentrytest.Blogspot.Com/Search/Label/Physics%20I)
Physics II (Http://Uentrytest.Blogspot.Com/Search/Label/Physics%20II)
Scholarships (Http://Uentrytest.Blogspot.Com/Search/Label/Scholarships)
Study (Http://Uentrytest.Blogspot.Com/Search/Label/Study)
Uet (Http://Uentrytest.Blogspot.Com/Search/Label/Uet)
Follow Me @ Instagram
http://uentrytest.blogspot.com/2015/06/pieas-ms-test-2014-questions.html 12/12