()*+*,-./01#-2/&34'05%6
It is a part of a lathe machine and is used to support lengthy jobs. To accommodate works of
different lengths between centres, the tail-stock may be moved on the lathe bed to the required
position and clamped by means of a clamping bolt.
Figure 18.18 shows various parts of a tail-stock. The barrel 2 is fitted into the bore of the
tail-stock body 1 and is prevented from rotation by the feather key 9 placed underneath of it. The
barrel has a threaded portion at its end and the spindle 3 is inserted into the barrel through this.
The hand wheel 6 is mounted on the spindle by a key and is retained in position by a nut. The
spindle bearing 5 is placed between the hand wheel and the tail-stock body. A tapered hole provided
at the front end of the barrel, receives the dead centre 4 or a tapered shank of the drill or reamer.
When the hand wheel is operated, the barrel is made to move in or out of the tail-stock
body. In the required position of the barrel, clamping may be made by means of the clamping
lever 7 and stud 8 which is fitted to the tail-stock body. The spindle bearing is fixed to the body by
means of the screws 10.
!"#$%&'#
Figure 18.18 shows215 the details of a lathe tail-stock. Assemble the parts and draw to a suitable
scale, (i) sectional view from the front
3 9and3 (ii) view from the left. 8 1.5
24
12
M6
!1
60
8
()*+*7-8&33&9:-8/%1&9#-2/&34'05%6 !12
12
Jobs35 requiring milling operations in relation to their axes of rotation, are usually supported
14 14
10
!36
!60
!68
!78
!18
!31
!36
30°
between the centres of theM6dividing head and adjustable M12 centre provided in the tail-stock. The
!1
!6 4 HOLES, DEEP 9 3 5
!12
8
parts of a milling machine PCD 52 tail-stock are shown in Fig. 18.19. This is similar to the lathe tail-
R21 R18 7
M12×18
stock.
15 R96
6
R15 R15 26 4 HOLES, !24
24 The
18 screw 4120 is introduced into R24 the threaded hole ofR27
body 1. Centre 2 is inserted into
DIA 6, PCD 52 the
1
body such that, the hole provided
18 in it enters onto the screw 4. Hand wheel 3 is mounted on the
R40
144
! 42 R9
adjustment, while clamping the job between R9 the centres.
R9 After adjustment, the centre
24 can be !15
3 !18
locked by22 the screw 5, which is introduced 40 into the body, prior to the location of the centre in the
!42
!31
°
14
6
36
60
3
!1
36 6 9
68
216 12 18 12
5
!"#$%&'#
90° shown in Fig. 18.19 and draw, (i) sectional
Assemble the parts of the milling machine tail-stock, 6
18
view
48from the front and
162 (ii) view from the right. KEYWAY,
1:20 SQ Thd Dia 21×3 LH M13 4×2
12 4 Parts list
20
!18
!36
!24
!6 1 Body Cl 1
10
15
M12
8 Stud MS 1
60°
!18
!26
!18
9 Feather key MS 1
51 10 Screw MS 4
162 6 26 24 14 1.5 12 27
3 4
Fig. 18.18 Lathe tail-stock
4 8 7 3 1 2 5 6
10
Fig. 18.18A Lathe tail-stock
\Des18-4.pm5