Anda di halaman 1dari 5

1043 Nano-Fil

Detailing techniques

[1] Preparation method before applying 1043 Nano fil


The Preparation method will be different for each car since it depends on the conditions
of the painted surfaces of the car. However, please do not forget to undergo your usual
operation such as removing contaminants or oily residues, polishing, and air-blowing
because it will influence the performance and durability of the coating.

[2]Applying method for 1043 Nano-Fil


① Blending the liquids
Pour the necessary amount of the main liquid into a scaled plastic bottle (included in
the kit). Then measure the liquid of the additive (one tenth of the amount of the main
liquid you poured in the plastic bottle) with a syringe and pour it in the plastic bottle
and shake it well.

Application techniques:
The standard amount to apply to a standard-sized car is 25-30ml (e.g. amount of main
liquid: 30ml, amount of additive: 3ml).
*The blend ratio of the main liquid and additive is changeable so to adjust the time for
hardening of the coat in a manner that will not influence the hybrid coating.
About ten percent of the liquid may be reduced depending on the detailing environment,
etc. However, please do not forget to check the environment when detailing.
② Applying the liquid on the painted surfaces
Apply a small amount of the liquid to an applicator sponge and spread it thin and
evenly to each panel of the painted surfaces.
(Applying the liquid by a polisher is also possible, but it may result in a thinner coating
compared to a hand applied coating.)

③ Spreading the liquid to other areas of the painted surface


After applying the liquid, wait for 3-5 minutes in spring or summer times, and 5-10
minutes in autumn or winter to dry, though it depends of the climate conditions in each
country. After drying, wipe off some amount of the liquids on the painted surface with a
dry micro fiber cloth to spread to other areas. You do not have to wipe off the liquid
completely at this minute.

Application techniques:
The waiting time after application of the liquid depends on the environment such as
climate and temperature. If the waiting time is too long, please note that the coating
might harden and it would be difficult to wipe off.
④ Wiping
Wiping off the liquid
Take another micro fiber cloth and soak it with luke-warm water or normal water, and
lightly wring it so the water will not drip from the cloth. Then wipe off the excess faster
than normal but not too fast.

Application techniques:
If you have waited too long after applying the liquid, the coating will whiten and gets
hard to wipe off with a cloth. In that case, by changing the surface of the cloth after each
careful wipe, you may be able to wipe off the excess liquid.

⑤ Finish
Wipe off the water by another dry micro fiber cloth.

Application techniques:
When using long-haired micro fiber cloths, the fibers of the cloth may sometimes stay on
the painted surface. In that case, please wipe off with a wet and well wrung out cloth
after the coating has hardened.
⑥ To make a more beautiful appearance
Please do the operation in accordance to the weather and temperature. 1043 Nano-Fil
delivers good performance even if the coating was applied only once on the painted
surface. However, by applying a second time and adding another layer on the coating, it
will become more glossy and thick.

Application techniques:
When you give the car a second coating, please make the waiting time for drying less
than the first coating to prevent difficulty of wiping off after drying.

[3] Precautions for use


※After applying the liquid, please do not get the car wet for 2-3 hours.
If you have applied only a single coating, and if the coating is tack free after drying for 3
hours, it will take about 24 hours to dry completely.

※Please use all the liquid that were blended together.


Do not use the blended liquid after leaving it for long.
After the blended liquid has been left for a long time, it is not useable.

※Rinse out the blending bottle and syringe with IPA (isopropyl alcohol) after use.
Otherwise, the remaining liquid inside the bottle will harden and be difficult for use.

※If you are reusing the cloth you have used during applying the liquid, please wash
away with IPA immediately after use.
However, please do not use the cloth if it becomes hardened after washing off with IPA.

※Please use the liquids as soon as possible after opening the package.

※Close the jar tightly and store it in a cool and dark place.
However, refrain from storing it in a refrigerator since dew condensation can be formed
by thermal difference when opening the jar again.
[4] For customers using for the first time
If you are using the product for the first time, apply the liquid in about 50 centimeters
square and avoid applying it onto large areas all at once. By checking the condition of
the application of the liquid and your work will help you capture a sense of application
and helps you reduce unevenness.
Also, pay attention to the points below at time of application.

[Attention]
*Please obey the mixing ratio for the main liquid and the additive.
The standard ratio is [main liquid 10: the additive 1].
If the ratio largely differs or the additive is too much, it will be difficult to wipe off,
resulting in unevenness of the coating surface.
We recommend the use of a sponge that has a hard backing or the sponge thickness is
less than the hard backing.

Anda mungkin juga menyukai