litronic`
Hydraulic Excavator
Operating weight with backhoe attachment 650,6 t/1,434,350 lb
Operating weight with shovel attachment 655,8 t/1,445,800 lb
Engine output 2400 kW/3218 HP
Bucket capacity 25,00 – 33,00 m3/32.7 – 43.2 cuyd
Shovel capacity 25,00 – 34,00 m3/32.7 – 44.5 cuyd
Mining Power.
1
2 10
11
3
12
4
13
14
5
Uppercarriage R 996 E
2
Engine Hydraulic System
Incoming Supply Requirements Hydraulic pumps
Network power supply ____ 3-Phase AC for attachment and
Voltage __________________________ 6600 Volts ± 10 % travel drive, max. flow ____ 8 x 840 l/min/8 x 222 gpm
Frequency (standard) ______ 50 Hz ± 1 Hz (or 60 Hz – dependent Max. working pressure ____ 320 bar/4640 PSI
on country) Hydraulic pumps
Nominal excavator for swing drive,
power ____________________________ 2500 kW max. flow ________________________ 4 x 413 l/min/4 x 109 gpm
Average energy Max. working pressure ____ 350 bar/5075 PSI
consumption __________________ 1800 kWh at S1 Pump regulation __________________ horsepower summation with pressure
(Other voltages available on request) compensation, flow compensation,
Electric Motor Specifications automatic oil flow optimizer
Manufacturing company __ ALSTOM Hydraulic tank capacity ________ 4600 l/1215 gal
Model ____________________________ N3 RX 450 Hydraulic system capacity ____ 8200 l/2166 gal
Type ______________________________ AC squirrel cage motor Hydraulic oil filter ________________ filtration of entire return flow, 1 high
Number of motor ____________ 2 pressure filter for each main pump
Output of one motor ________ 1200 kW at 1500 RPM Hydraulic oil cooler ______________ with thermostatically regulated
(or 1800 RPM at 60 Hz) cooling fan driven via hydraulic
Power factor __________________ cos f = 0,88 piston pumps
Protection class ______________ IP 55 EN 60529 Lubrication __________________________ central lubrication system
Isolation class ________________ F
Motor cooling ________________ integrated air-to-air heat exchanger
Motor construction __________ IM 2001
Starting method ______________ starting transformer
Electrical System
the high and low tension cubicle are integrated with a robust
sheet steel construction
High Voltage Section ____________ – Protection class IP 55 EN 60529
– Mechanical isolator switch on out-
side of enclosure to disconnect high
Hydraulic Controls
voltage for maintenance Servo circuit ________________________ independant, electric over hydraulic
– Electrically operated interlocks to proportional controls of each function
disconnect high voltage when Emergency control __________ via accumulator for all attachment
enclosure doors are opened functions with stopped engine
– Main circuit breaker for protection Power distribution ________________ via monoblock control valves with
against short circuit, undervoltage integrated primary relief valves and
and as emergency stop flanged on secondary valves for
– High voltage contactors for main travel
motor control Flow summation ____________ to attachment and travel drive
– High voltage fuses for transformer Control functions
primary protection Attachment and swing ____ proportional via joystick levers
– Start transformer to reduce inrush Travel ____________________________ proportional via foot pedals or hand
current levers
– Three phase transformer: Bottom dump bucket ______ proportional via foot pedals
6600 V/400 V for auxiliary compo- Operation with one engine possible
nents
– Three phase transformer:
6600 V/230 V for auxiliary compo-
nents
– Current transformers to drive con-
ventional motor protection relay
– Thermostatically controlled fans
and anti-condensation heaters in-
side enclosure
Low Voltage Section ____________ – Protection class IP 55 EN 60529
– Three phase transformer secondary
Swing Drive
protected with circuit breaker and Hydraulic motor __________________ 4 Liebherr axial piston motors
protected against earth leakage Swing gear __________________________ 4 Liebherr planetary reduction gears
– Ground fault protection with Swing ring __________________________ Liebherr, sealed triple roller swing
leakage current device ring, internal teeth
– Step down transformer: Swing speed ________________________ 0 – 3.5 RPM
400 V/24 V DC stabilized for bord- Swing-holding brake ____________ hydraulically released, maintenance-
control free, multi-disc brakes integrated in
– Motor protection relay for: each swing gear
x motor winding and bearing
x temperature
x overload
x single phase
x stalling
x ground fault
x short circuit
x phase failure
x phase main motor sequence pro-
tection for all hydraulic pumps
and three phase auxiliary drive
Uppercarriage
– Power supply for continuous moni- Design ________________________________ torque resistant designed upper
toring system frame in box type construction for
– Electrically operated interlocks to superior strength and durability
disconnect high voltage when Attachment mounting __________ parallel longitudinal main girders in
enclosure door are opened box-section construction
– Thermostatically controlled fans Catwalks ______________________________ on the right side with a hydraulically
and anti-condensation heaters in- driven access ladder, additional
side enclosure emergency ladder in front of the cab
Technical Data
3
Service Flap Central Lubrication System
Design ________________________________ hydraulically actuated service flap, Type ____________________________________ Lincoln Centromatic lubrication
easily accessible from ground level to system for the entire attachment and
allow: swing ring
– hydraulic oil refill Grease pumps ______________________ 2 Lincoln Powermaster pumps with
– splitterbox oil quick change switch over function, plus 1 separate
– swing gearbox oil quick change pump for swing ring teeth
– windshield washer water refilling Capacity ______________________________ 1 x 600 l/158,5 gal bulk container for
– grease refill with filters for both attachment and swing ring, separated
containers 1 x 80 l/21 gal grease drum for swing
Quick coupler upon request ring teeth
Operator’s Cab
Design ________________________________ resiliently mounted, sound insulated,
large windows for all-around visi-
bility, integrated falling object protec-
tion FOPS
Operator’s seat ____________________ suspended, body-contoured with
shock absorber, adjustable to oper-
ator’s weight
Cabin windows ____________________ 20,5 mm/0.8 in tinted armored glass
for front window and left hand side
windows,
Attachment
all other windows in tinted safety Design ________________________________ box type structure with large steel
glass, castings in all high-stress areas
high pressure windshieldwasher- Pivots __________________________________ sealed with double side centering
system with 75 l/20 gal watertank, with 1 single floating pin per side,
sun louvers on all windows in heavy all bearings with wear resistant, steel
duty design bushings,
Heating system/ bolts hardened and chromium-plated
air conditioning ____________________ heavy duty, high output air condi- Hydraulic cylinders ______________ Liebherr design, all cylinders located
tioner and heater unit in well protected areas
Cabin pressurization ____________ ventilation unit with filters Hydraulic connections __________ pipes and hoses equipped with SAE
Controls ______________________________ joystick levers integrated into arm- split flange connections
rest of seat Kinematics __________________________ Liebherr parallel face shovel attach-
Monitoring __________________________ via gauge and display ment geometry
Automatic engine shut off ____ in case of winding and bearing over-
heating
Safety functions ____________________ additional gauges with constant
display for: engine load factor, hour-
meter, hydraulic oil temperature
Undercarriage
Construction ________________________ the construction of the undercarriage
is the same as on the diesel version
High voltage supply cable ____ the high voltage supply cable enters
at the rear of the undercarriage in a
contact box, protection classification
High Voltage Cable (as option)
IP 67, a sealed slip ring connection Flexible medium-voltage
with 4 power rings and brushholders, cables __________________________________ are to be selected in accordance with
protection classification IP 67, be- the application for trailing operation,
tween under- and uppercarriage particularly suitable for applications
feeds the high voltage section in which abrasion and extremely
Design ________________________________ 3-piece undercarriage, high mechanical stresses are to be
box type structures for center piece expected
and side frames, stress relieved Approvals/standards ____________ – DIN VDE 0250, Part 813
Hydraulic motor __________________ 2 axial piston motors per side frame (VDE = Association of German
Travel gear __________________________ Liebherr reduction gear Electrical Engineers)
Travel speed ________________________ 0 – 2,2 km/h/0 – 1.4 mph – MSHA P-189-4
Parking brake ______________________ spring engaged, hydraulically re- (= Mine Safety and Health Admini-
leased wet multi-disc brakes for each stration/Harrisburg, USA)
travel motor, maintenance-free – WUG/GE-83/98
Track components ________________ maintenance-free combined pad-link, (= Approval of the Polish Mining
heavy duty track shoes Inspectorate, necessary for use of
Track rollers/carrier rollers __ 7/3 cables in Polish mines)
Automatic track tensioner ____ pressurized hydraulic cylinder with Cable capacity ______________________ 300 m trailing cable
accumulator, maintenance free Cable sizes __________________________ dependent on voltage, current and
Transport ____________________________ undercarriage side frames are re- cable length
movable Current-carrying capacity ______ according to DIN VDE 0298, Part 4
4
A2 X
A1 E
A D F
W
C
H1
H
P K
Q
N L
S U
B Z
V
mm/ft-in mm/ft-in
A 7000/22’11” L 7500/24’ 7”
A1 7430/24’ 4” U 10000/32’ 9”
A2 8250/27’ 1” P 2985/ 9’ 9”
B 7650/25’ 1” Q 1435/ 4’ 8”
C 9070/29’ 9” S 6000/19’ 8”
D 7550/24’ 9” N 1400/ ’55”
E 7795/25’ 7” W 9750/32’ 0”
F 2780/ 9’ 1” V 14350/47’ 1”
H 6275/20’ 7” X 22600/74’ 1”
H1 8480/27’10” Z 12465/40’10”
K 2845/ 9’ 4”
A2 X1
A1 E
A D F
C
W1
H1 H
P K
Q
N L
S U
B Z
V1
mm/ft-in mm/ft-in
A 7000/22’11” L 7500/24’ 7”
A1 7430/24’ 4” U 10000/32’ 9”
A2 8250/27’ 1” P 2985/ 9’ 9”
B 7650/25’ 1” Q 1435/ 4’ 8”
C 9070/29’ 9” S 6000/19’ 8”
D 7550/24’ 9” N 1400/ ’55”
E 7795/25’ 7” W1 8500/27’10”
F 2780/ 9’ 1” V1 17800/58’ 4”
H 6275/20’ 7” X1 23450/76’11”
H1 8480/27’10” Z 12465/40’10”
K 2845/ 9’ 4”
Dimensions
5
Digging envelope
Max. reach at ground level 20,00 m/65’ 7”
Max. teeth height 16,60 m/54’ 5”
m ft Max. dump height 10,50 m/34’ 5”
Max. digging depth 8,80 m/28’10”
12 40
10
30
8
6 20
4
10
2
0 0
-2
-10
-4
-6 -20
Operating Weight and
-8
-30
Ground Pressure
-10 The operation weight includes the basic machine
m0 2 4 6 8 10 12 14 16 18 20 22
with backhoe attachment and bucket 30,00 m3/
39.2 cuyd.
ft 0 10 20 30 40 50 60 70
Pad width mm/in 1400/55
Weight kg/lb 650600/1,434,350
Ground pressure kg/cm2/PSI 2,77/39.40
Buckets
Cutting width SAE mm/in 4150/163”1) 4700/185”1) 4700/185”1)
Capacity SAE heaped m3/cuyd 25,00/32.7 30,00/39.2 33,00/43.1
Weight kg/lb 35000/77,161 39000/85,980 40000/88,185
Suitable for material up to a specific weight of t/m3/lb/cuyd 2,20/3700 1,80/3000 1,60/2700
Wear kit level III II II
Notes:
1) Bucket with delta cutting edge and tooth system Posilok size S 145
Level II: For heavy rock, not detoriorated or cracked. Has to be shot to be dug.
Level III: For highly-abrasive materials such as rock with a high silica content, sandstone etc.
Backhoe Attachment
6
Digging envelope
Max. reach at ground level 15,60 m/51’ 6”
Max. dump height 14,30 m/46’11”
m ft Max. crowd length 6,40 m/21’ 0”
Bucket opening width T 2800 mm/110”
70
20 Crowd force at
ground level: 1960 kN (199,8 t)/440,484 lb
18 60 Max. crowd force: 2340 kN (238,5 t)/525,803 lb
Max. breakout force: 1905 kN (194,2 t)/428,138 lb
16
50
14
T
12 40
10
30
8
6 20
4
10
2
0 0
Notes:
1) Bottom dump bucket with delta cutting edge and tooth system Posilok size S 145
Level II: For heavy rock, not deteriorated or cracked. Has to be shot to be dug.
Level III: For highly-abrasive materials such as rock with a high silica content, sandstone etc.
Shovel Attachment
7
L
Cab
L Length mm/ft-in 3215/10’ 6”
H Height mm/ft-in 2885/ 9’ 6”
H Width mm/ft-in 1900/ 6’ 3”
Weight kg/lb 2800/6,173
L
Powerpack module (two)
L Length mm/ft-in 5280/17’ 4”
H Height mm/ft-in 3640/11’11”
H Width mm/ft-in 2070/ 6’ 9”
Weight kg/lb 2 x 22000/2 x 48,500
L Rotation deck
(with swing ring, swing gears and control valve bracket)
L Length mm/ft-in 9750/32’ 0”
H H Height mm/ft-in 4250/13’11”
Width mm/ft-in 4270/14’ 0”
Weight kg/lb 77800/171,500
L
Counterweight
L Length mm/ft-in 1250/ 4’ 1”
H Height mm/ft-in 3430/11’ 3”
Width mm/ft-in 7360/24’ 2”
H Weight kg/lb 60000/132,277
Miscellaneous
L
L Length mm/ft-in 4500/14’ 9”
H Height mm/ft-in 2600/ 8’ 6”
Width mm/ft-in 2000/ 6’ 7”
H
Weight kg/lb 5000/11,023
L
Undercarriage central girder
L Length mm/ft-in 4000/13’ 1”
H Height mm/ft-in 2690/ 8’10”
Width mm/ft-in 4600/15’ 1”
H Weight kg/lb 40000/88,185
L Shovel boom
L Length mm/ft-in 8650/28’ 4”
H Height mm/ft-in 3300/10’10”
H Width mm/ft-in 3350/11’ 0”
Weight kg/lb 53240/117,374
L
Shovel stick
L Length mm/ft-in 5620/18’ 5”
H Height mm/ft-in 2300/ 7’ 6”
Width mm/ft-in 3350/11’ 0”
H Weight k /lb 27150/59,855
9
L Gooseneck boom with two stick
cylinders
L Length mm/ft-in 12500/41’ 0”
H H Height mm/ft-in 4500/14’ 9”
Width mm/ft-in 2800/ 9’ 2”
Weight kg/lb 68950/152,009
L
Stick with two bucket cylinders
L Length mm/ft-in 7500/24’ 7”
H Height mm/ft-in 3000/ 9’10”
H Width mm/ft-in 2500/ 8’ 2”
Weight kg/lb 40800/89,950
L
Backhoe bucket
LFR/SP 10005532-1-02.02 Printed in Germany by Typodruck Gagstatter. Illustrations and data may differ from standard equipment. Subject to change without notice.
Cutting width mm/in 4150/163” 4700/185” 4700/185”
Capacity m3/cuyd 25,00/32.7 30,00/39.2 33,00/43.1
H L Length mm/ft-in 4650/15’3” 4650/15’3” 4650/15’ 3”
H Height mm/ft-in 3150/10’4” 3150/10’4” 3300/10’10”
Width mm/ft-in 4200/13’9” 4750/15’7” 4750/15’ 7”
Weight kg/lb 35000/77,162 39000/85,980 40000/88,185
LIEBHERR-FRANCE S.A. 2, Avenue Joseph Rey, B.P. 287, F-68005 Colmar-Cedex, ç 03 89 21 35 10, Fax 03 89 21 37 93
www.liebherr.com, E-Mail: info@lfr.liebherr.com
With compliments: