Strength of materials is a branch of applied mechanics that deals with the behavior of
solid bodies subjected to various types of loading. The solid bodies include axially-loaded
bars, shafts, beams, and columns. The objective of analysis will be the determination of the
stresses, strains, and deformations produced by the loads.
Simple Stress ():
If a cylindrical bar is subjected to a direct pull or push along its axis, then it is
said to be subjected to tension or compression.
P P P P
Tension Compression
Normal stress () : is the intensity of normal force per unit area
Load
Stress =
Area
P
A
stress may thus be compressive or tensile depending on the nature of the load and will be
measured in units of Newton per square meter (N/m2). This unit, called Pascal
1 Pa=1 N/m2
1 KPa=1000 Pa=103 Pa
1 MPa=106 Pa
1 GPa=109 Pa
1
Normal Strain ():
If a bar is subjected to a direct load, and hence a stress, the bar will change in
length. If the bar has an original length (L) and changes in length by an amount (L), the
strain produced is defined as follows:
change in length
Strain()=
original length
L
L
P P
L L
Shear load
Shear stress=
Area resisting shear
Q Q
Q
Q
A
2
Area resisting shear is the shaded area as shown above.
P P
P A
P
P P
P/2
P
A
P/2
P/2
Double shear stress
A
B
1
P P 2
A C
3
F
b b
Ab
Consider the bolted connection shown above, this connection consists of a flat bar
A, a clevis C, and a bolt B that passes through holes in the bar and clevis. Consider the
bearing stresses labeled 1, the projected area Ab on which they act is rectangle having a
3
height equal to the thickness of the clevis and a width equal to the diameter of the bolt, the
bearing force Fb represented by the stresses labeled 1 is equal to P/2. The same area and the
same force apply to the stresses labeled 3. For the bearing stresses labeled 2, the bearing
area Ab is a rectangle with height equal to the thickness of the flat bar and width equal to
the bolt diameter. The corresponding bearing force Fb is equal to the load P.
Shear Strain ( ):
Shear strain is a measure of the distortion of the element due to shear. Shear
strain is measured in radians and hence is non-dimensional, i.e. it has no units.
E
This constant is given the symbol E and termed the modulus of elasticity or
Young's modulus.
Poisson's Ratio ( ):
Consider the rectangular bar shown below subjected to a tensile load. Under
the action of this load the bar will increase in length by an amount L giving a longitudinal
strain in the bar of:
L
L
L
4
The bar will also exhibit a reduction in dimensions laterally i.e. its breadth and
depth will both reduce.
b b
P 2 P
d
d
2
The associated lateral strains will both be equal, will be of opposite sense to the
longitudinal strain, and will be given by:
d b
lat
d b
Poisson's ratio is the ratio of the lateral and longitudinal strains and always
constant
Lateral Strain
Poisson's ratio=
Longitudin al Strain
d / d
L / L
Longitudinal Strain=
E
Lateral Strain=
E
Modulus of Rigidity ( G ):
For materials within the elastic range the shear strain is proportional to the shear
stress producing it.
Shear Stress
=Constant
Shear Strain
=G
The constant G is termed the modulus of rigidity.
5
Example 1:A 25 mm square cross-section bar of length 300 mm carries an axial
compressive load of 50 KN. Determine the stress set up in the bar and its change of length
when the load is applied. For the bar material E=200 GN/m2.
50 KN 25 mm
300 mm
P
A
50 10 3
= 6
=80000000 N/m2
625 10
=80 MN/ m2
E
80 10 6
= =0.0004
200 10 9
L L
L=0.0004×300×10-3=0.12×10-3m
L=0.12 mm
6
Example 2: Two circular bars, one of brass and the other of steel, are to be loaded by a
shear load of 30 KN. Determine the necessary diameter of the bars a) in single shear b) in
double shear, if the shear stress in the two materials must not exceed 50 MN/m2 and 100
MN/m2 respectively.
a) Single Shear
F F
A
A
A 0.0006
A=r2 r r
r=13.8197×10-3 m
the diameter of the bar (d)=27.639×10-3 m
For steel material
30 10 3
A= =0.0003 m2
100 10 6
0.0003
r =9.772×10-3 m
the diameter of the bar (d)=19.544×10-3 m
b) Double Shear
F F
A
2A 2
For brass material
30 10 3
A= =0.0003 m2
2 50 10 6
0.0003
r =9.772×10-3 m
the diameter of the bar (d)=19.544×10-3 m
For steel material
30 10 3
A= =0.00015 m2
2 100 10 6
0.00015
r =6.909×10-3 m
the diameter of the bar (d)=13.819×10-3 m
7
Example 3: The 80 kg lamp is supported by two rods AB and BC as shown. If AB has a
diameter of 10 mm and BC has a diameter of 8 mm, determine the average normal stress in
each rod.
A C
Fx 0
4 5
FBC FBA cos 60 0 3
5 60 B 4
F y 0
3
FBC FBA sin 60 784 .8 0
5
FBC=1308-1.44337FBA ……….(2)
80 9.81 784 .8 N
1308-1.44337FBA=0.625FBA
FBA=632.38 N
FBC=395.2375 N
FBA 632.38
BA =
ABA (5 10 3 ) 2
BA=8.051877×106 Pa
BA=8.051877 MPa
FBC 395.2375
BC =
ABC ( 4 10 3 ) 2
BC=7.863149×106 Pa
BC=7.863149 MPa
8
Example 4: Shafts and pulleys are usually fastened together by means of a key, as shown.
Consider a pulley subjected to a turning moment T of 1 KN.m keyed by a 10 mm×10
mm×75 mm key to the shaft. The shaft is 50 mm in diameter. Determine the shear stress on
a horizontal plane through the key.
1 KN T
10 mm
F
10 mm
50 mm
M o 0
1 10 3 F 0.025 0 75 mm
F=40000 N
F=40 KN
F
F
A
F
A is the shaded area
40 10 3
=
10 10 3 75 10 3
=53.333×106 N/m2
=53.333 MN/m2
Example 5: Consider a steel bolt 10 mm in diameter and subjected to an axial tensile load
of 10 KN as shown. Determine the average shearing stress in the bolt head, assuming
shearing on a cylindrical surface of the same diameter as the bolt.
A=dt
A=×10×10-3×8×10-3=0.000251327 m2
10 mm 10 KN
F
A
10 10 3
=
0.000251327
8 mm
=39.7888×106 N/m2
=39.7888 MN/m2
9
Example 6: The bar shown has a square cross section for which the depth and thickness are
40 mm. If an axial force of 800 N is applied along the centroidal axis of the bar's cross
sectional area, determine the average normal stress and average shear stress acting on the
material along a) section plane a-a and b) section plane b-b.
P
A a b
800 N
800
= 60
40 10 40 10 3
3
a b
=500 KN/m2
F
800 N 800 N
A
F=0
=0
F2 F2
A
800 sin 60
= 3 3
=375 KN/m2
46.188 10 40 10
F1
A
800 cos 60
= 3 3
=216.50645 KN/m2
46.188 10 40 10
10
Example 7: Determine the total increase of length of a bar of constant cross section
hanging vertically and subject to its own weight as the only load. The bar is initially
straight.
Aydy
d
AE
L dy L dy
d
0
y
Aydy
L
=
0
AE
A yA
L
AE 0
= ydy
A 1 2
L
= y
AE 2 0
A 2
= L
2 AE
AL.L
=
2 AE
W=AL
W .L
=
2 AE
11
Example 8: A member is made from a material that has a specific weight and modulus of
elasticity E. If its formed into a cone having the dimensions shown, determine how far its
end is displaced due to gravity when its suspended in the vertical position.
x y r
=
r L P( y )
y x
x r L
L
y
v= x 2 y y
3
w(y)=v= x 2 y
3
r y
2 2 w( y )
= 2 y
3 L
r 3
2
w(y)= y
3 L2
From equilibrium P(y)=w(y)
r 3
2
P(y)= y
3 L2
2
r
A(y)=x2= 2 y 2
L
r 3
2
y dy
P( y )dy 3 L2
d= 2
A( y ) E r 2
2 y E
L
d= ydy
3E
ydy
L L
d
0 0
3E
L2
6E
12
Example 9: A solid truncated conical bar of circular cross section tapers uniformly from a
diameter d at its small end to D at the large end. The length of the bar is L. Determine the
elongation due to an axial force P applied at each end as shown.
d
r y
2
D d
d D
y 2 2 P P
x L
D d x
y( )
2 2 L
d D d x L
r ( )
2 2 2 L D d
y
A(x)=r2 2 2
r
P P
A(x)= ( )
d D d x
2 2 2 L x dx
Pdx Pdx
d= = 2
A( x) E d D d x
( ) E
2 2 2 L
L
Pdx
= 2
d D d x
( ) E
0
2 2 2 L
1 L
P d D d x
= ( )
D d 2
E ( )
2 2 L 0
L 2 2
L
PL PL PL
= =
D d d D d x D d d D d D d d
E ( ) ( ) 0 E ( ) E ( )
2 2 2 2 2 L 2 2 2 2 2 2 2 2
PL PL 4 PL 1 1
= = 2 2
D 2
dD Dd d 2
E D dD Dd d
E ( ) E ( )
4 4 4 4
4 PL
=
dDE
13
Example 10: Determine the smallest dimensions of the circular shaft and circular end cop
if the load it is required to support is 150 KN. The allowable tensile stress, bearing stress,
and shear stress is (t)allow=175 MPa, is (b)allow=275 MPa, and allow=115 MPa.
Fb
(b)allow=
Ab
150 10 3 P 150 KN
275×106=
Ab
Ab=0.0005454 m2
d2
Ab= d 22
4
4 Ab 4 0.0005454
d2=
d2=0.026353 m=26.353 mm
P
(t)allow=
A
150 10 3
175×106=
A t
A=0.0008571 m2 30 mm
A= [d12 (30 10 3 ) 2 ] =0.0008571
4
d1=0.04462 m=44.62 mm d1
F
allow=
A
150 10 3
115×106=
A
A=0.0013043 m2
1. A=td
0.0013043= t××30×10-3
t=0.013839 m=13.839 mm
2. A=td2
0.0013043= t××26.353×10-3
t=0.01575 m=15.75 mm
14
Statically Indeterminate Members:
Ifthe values of all the external forces which act on a body can be
determined by the equations of static equilibrium alone, then the force system is statically
determinate.
P2
P P1
R1
R2 R3 R1
R2 R3
In many cases the forces acting on a body cannot be determined by the equations of
static alone because there are more unknown forces than the equations of equilibrium. In
such case the force system is said to be statically indeterminate.
P P
M1
R1 R4 R4
R1
R2 R3 R2 R3
15
Example 11: A square bar 50 mm on a side is held rigidly between the walls and loaded
by an axial force of 150 KN as shown. Determine the reactions at the end of the bar and the
extension of the right portion. Take E=200 GPa.
150 KN 150 KN
R1 R2
100 mm 150 mm
R1+R2=150×103 ………………(1)
1=2
R1 100 10 3 R2 150 10 3
50 10 3 50 10 3 200 10 9 50 10 3 50 10 3 200 10 9
0.1R1=0.15R2
R1=1.5R2 …………………..(2)
1.5R2 + R2=150×103
R2 =60000 N
R1=90000 N
2=0.000018 m
2=0.018 mm
16
Example 12: A steel bar of cross section 500 mm2 is acted upon by the forces shown.
Determine the total elongation of the bar. For steel, E=200 GPa.
A B C D
50 KN 45 KN
15 KN 10 KN
500 mm 1m 1 .5 m
A B B C
50 KN 50 KN 50 KN 35 KN
15 KN
C D
45 KN 45 KN
For portion AB
PL 50 10 3 500 10 3
1= = =0.00025 m=0.25 mm
AE 500 10 6 200 10 9
For portion BC
PL 35 10 3 1
2= = =0.00035 m=0.35 mm
AE 500 10 6 200 10 9
For portion CD
PL 45 10 3 1.5
3= = =0.000675 m=0.675 mm
AE 500 10 6 200 10 9
T=1+2+3
T=0.25+0.35+0.675=1.275 mm
17
Example 13: Member AC shown is subjected to a vertical force of 3 KN. Determine the
position x of this force so that the average compressive stress at C is equal to the average
tensile stress in the tie rod AB. The rod has a cross-sectional area of 400 mm2 and the
contact area at C is 650 mm2.
FAB
B
3 KN 3 KN
x x
A A
C C
200 mm 200 mm
FC
F y 0
FAB+FC-3000=0
FAB+FC=3000 ………………………(1)
AB=C
FAB FC
AAB AC
FAB FC
6
400 10 650 10 6
FAB=0.6153 FC …………………….(2)
FC=1857.24 N
FAB=1142.759 N
M A 0
FC×200×10-3-3000×x=0
1857.24 0.2
x =0.123816 m=123.816 mm
3000
18
Example 14: The bar AB is considered to be absolutely rigid and is horizontal before the
load of 200 KN is applied. The connection at A is a pin, and AB is supported by the steel
rod EB and the copper rod CD. The length of CD is 1m, of EB is 2 m. The cross sectional
area of CD is 500 mm2, the area of EB is 250 mm2. Determine the stress in each of the
vertical rods and the elongation of the steel rod. Neglect the weight of AB. For copper
E=120 GPa, for steel E=200 GPa.
E
M A 0 C
A D
3 B
FCo×1+Fs×2-200×10 ×1.5=0
FCo=1.2 Fs …………………….(2) E
C
From equations (1) and (2) A D B
Fs=93750 N Co
s
FCo=112500 N
Fs 93750
s = =375000000 Pa
As 250 10 6
s=375 MPa
FCo 112500
Co = =225000000 Pa
ACo 500 10 6
Co=225 MPa
s L 375 10 6 2
s = =0.00375 m=3.75 mm
E 200 10 9
19
Thermal Stresses:
A change in temperature can cause a material to change its dimensions. If the
temperature increases, generally a material expands, whereas if the temperature decreases
the material will contract.
The deformation of a member having a length L can be calculated using the
formula:
T=×T×L
FL
T= =×T×L
AE
T=E××T
: Linear coefficient of thermal expansion. The units measure strain per degree of
temperature. They are (1/ºF) in the foot-pound-second system and (1/ºC) or (1/ºK) in SI
system.
T: Change in temperature of the member.
L: The original length of the member.
T: The change in length of the member.
Example 15: The A-36 steel bar shown is constrained to just fit between two fixed
supports when T1=60º F. If the temperature is raised to T2=120º F determine the average
normal thermal stress developed in the bar. For steel =6.6×10-6 1/ºF, E=29×103 Ksi.
0.5 in
FA 0.5 in
T F
A
F y 0
FA-FB=F
T-F=0
20 in
T=×T×L
T=E××T
=29×103 ×6.6×10-6 ×(120-60)
=11.484 Ksi B
FB
20
Example 16: A 2014-T6 aluminum tube having a cross sectional area of 600 mm2 is used
as a sleeve for an A-36 steel bolt having a cross sectional area of 400 mm2. When the
temperature is T1=15º C, the nut hold the assembly in a snug position such that the axial
force in the bolt is negligible. If the temperature increases T2=80º C, determine the average
normal stress in the bolt and sleeve. For aluminum =23×10-6 1/ºC, E=73.1 GPa, for steel
=12×10-6 1/ºC, E=200 GPa.
150 mm
F y 0
Fsl-Fb=0 Fb Fsl
Fsl=Fb=F
Initial Position
( b ) T
( b ) T ( b ) F ( sl ) T ( sl ) F
( sl ) T
FL FL ( b ) F
[×T×L+ ]b=[×T×L- ]sl Final Position
AE AE
( sl ) F
F 0.15 F 0.15
12×10-6×0.15×(80-15)+ 6
= 23×10-6×0.15×(80-15)-
400 10 200 10 9
600 10 6 73.1 10 9
0.0052949×10-6F=0.00010725
F=20255 N
F 20255
b= =
Ab 400 10 6
b=50.637655 MPa
F 20255
sl= =
Asl 600 10 6
sl=33.758436 MPa
21
Example 17: The rigid bar shown is fixed to the top of the three posts made of A-36 steel
and 2014-T6 aluminum. The posts each have a length of 250 mm when no load is applied
to the bar, and the temperature is T1=20ºC. Determine the force supported by each posts if
the bar is subjected to a uniform distributed load of 150 KN/m and the temperature is
raised to T2=80ºC. For steel =12×10-6 1/ºC, E=200 GPa , for aluminum =23×10-6 1/ºC,
E=73.1 GPa.
300 mm 300 mm
( al )T ( ) 150 KN / m
al F
Initial Position ( st ) T
( st ) F
Final Position 60 mm
250 mm
40 mm 40 mm
F y 0 150 0.6 90 KN
2Fst+Fal=90000 …………….(1)
=(st)T-(st)F=(al)T-(al)F
1.20956×10-9Fal-0.994718×10-9Fst=0.000165 ………………..(2)
Fst=-16444.7 N
Fal=122888.8 N
22
Example 18: The rigid bar AD is pinned at A and attached to the bars BC and ED as
shown. The entire system is initially stress-free and the weights of all bars are negligible.
The temperature of bar BC is lowered 25ºK and that of the bar ED is raised 25ºK.
Neglecting any possibility of lateral buckling, find the normal stresses in bars BC and ED.
For BC, which is brass, assume E=90 GPa, =20×10-6 1/ºK and for ED, which is steel,
take =12×10-6 1/ºK, E=200 GPa. The cross-sectional area of BC is 500 mm2, of ED is
250 mm2.
E
M A 0
250 mm
A B
Pst×600×10-3-Pbr×250×10-3=0 D
300 mm
250 mm 350 mm
C
Pst=0.41666 Pbr ………..(1) Pst
br Ax
st
250 600
Pbr L Pst L Ay
L T L T Pbr
Abr E br Ast E st
250 600
br ( st )T
st
( st ) F
( br )T
( br ) F
23
Torsion:
Torque is a moment that tends to twist a member about its longitudinal axis.
When the torque is applied, the circles and longitudinal grid lines originally marked on the
shaft tend to distort into the pattern shown below.
T
Before deformation After deformation
Twisting causes the circles to remain circles and each longitudinal grid line
deforms into a helix that intersects the circles at equal angles. Also, the cross sections at
the ends of the shaft remain flat that is, they do not warp or bulge in or out and radial lines
on these ends remain straight during the deformation.
The Torsion Formula:
Consider a uniform circular shaft is subjected to a torque it can be shown
that every section of the shaft is subjected to a state of pure shear.
T
max
r
T
T
J
24
: The torsional shearing stress.
T: The resultant internal torque acting on the cross section.
: The distance from the centre (radial position).
J: The polar moment of inertia of the cross sectional area.
Tr
max
J
max: The maximum shear stress in the shaft, which occurs at the outer surface.
r: The outer radius of the shaft.
4
J r
2
4
J D
32
4
J (ro ri 4 ) ( Do4 Di4 )
2 32
TL
GJ T
L
A
T
25
If the shaft is subjected to several different torques or the cross sectional area or
shear modulus changes from one region to the next. The angle of twist of one end of the
shaft with respect to the other is then found from:
TL
GJ
In order to apply the above equation, we must develop a sign convention for the
internal torque and the angle of twist of one end of the shaft with respect to the other end.
To do this, we will use the right hand rule, whereby both the torque and angle of twist will
be positive, provided the thumb is directed outward from the shaft when the fingers curl to
give the tendency for rotation. D
LCD 10 N.m
LBC C
150 N.m
B 60 N.m
LAB
80 N.m
B 80 N.m
C
LAB 150 N.m
LBC 70 N.m
A
B
80 N.m 80 N.m
D
LAB
10 N.m
60 N.m
26
70 N.m
80 L AB 70 LBC 10 LCD
A/ D
GJ GJ GJ
P T
In SI units power is expressed in (watts) when torque is measured in (N.m) and
in (rad/s).
1 W=1 N.m/s
In the foot-pound-second or FPS system the units of power are (ft.lb/s); however
horsepower (hp) is often used in engineering practice where:
1 hp=550 ft.lb/s
For machinery the frequency of a shaft's rotation f is often reported. This is a
measured of the number of revolutions or cycles the shaft per second and is expressed in
hertz (1 Hz=1 cycle/s), 1 cycle=2 rad, then =2f
P=2fT
Tr
max
J
4 4
J D (50 10 3 ) 4 0.6135 10 6 m
32 32
1 10 3 25 10 3
max
0.6135 10 6
max=40.74979 MPa
27
TL
GJ
1 10 3 1
85 10 9 0.6135 10 6
=0.01917 rad.
Example 20: The pipe shown has an inner diameter of 80 mm and an outer diameter of 100
mm. If its end is tightened against the support at A using a torque wrench at B, determine
the shear stress developed in the material at the inner and outer walls along the central
portion of the pipe when the 80 N forces are applied to the wrench.
T=80×200×10-3+80×300×10-3
T=40 N.m
Tr
J
J ( Do4 Di4 )
32
J
32
(100 10 3 ) 4 (80 10 3 ) 4
J=5.7962×10-6 m4
Tri 40 40 10 3
=
J 5.7962 10 6
=0.276042 MPa
Tro 40 50 10 3
=
J 5.7962 10 6
=0.345053 MPa
28
Example 21: The gear motor can developed 0.1 hp when it turns at 80 rev/min. If the
allowable shear stress for the shaft is allow=4 ksi, determine the smallest diameter of the
shaft that can be used.
Tr
allow
J
4
J r
2
Tr
allow
4
r
2
2T
allow
r 3
2T
r3
allow
P
P=T. T
P=0.1×550=55 lb/s
=80×2/60=8.377 rad/s
55
T =6.5655 lb.ft
8.377
T=6.5655×12=78.786 lb.in
2 78.786
r3 =0.2323 in
4 10 3
d=0.4646 in
29
Example 22: The assembly consists of a solid 15 mm diameter rod connected to the inside
of a tube using a rigid disk at B. Determine the absolute maximum shear stress in the rod
and in the tube. The tube has an outer diameter of 30 mm and a wall thickness of 3 mm.
The rod
T=50 N.m
r=7.5×10-3 m
4
J r
2
J (75 10 3 ) 4
2
J=4.97009×10-9 m4
Tr
r
J
50 7.5 10 3
r =75.4512 MPa
4.97009 10 9
The tube
T=80 N.m
r=15×10-3 m
15 mm
4 12 mm
J (ro ri 4 )
2
-9
J (15 10 3 ) 4 (12 10 3 ) 4 =46.9495×10 m
2
4
Tro 80 15 10 3
t = =25.559 MPa
J 46.9495 10 9
30
Example 23: The tapered shaft shown below is made of a material having a shear modulus
G. Determine the angle of twist of its end B when subjected to the torque.
d 2 d1
y
2 2
d1 d d2
y d 2 d1 d d1 x
y 2
x 2L 2 L
x
d=d1+2y=d1+ (d 2 d1 )
L
4 x
J ( x) d [d1 (d 2 d1 ) ]4
32 32 L
L L L
T dx T dx 32T dx
G J ( x) 0 x G 0 x
0 G [ d1 ( d 2 d1 ) ]4 [ d1 ( d 2 d1 ) ]4
32 L L
L
32TL 1 32TL 1 1
3G (d 2 d1 ) x 3G (d 2 d1 ) d 23 d13
[ d 1 ( d 2 d 1 ) ]3
L 0
32TL d13 d 23
3G (d 2 d1 ) d 23 .d13
31
Example 24: The gears attached to the fixed end steel shaft are subjected to the torques
shown. If the shear modulus of elasticity is G=80 GPa and the shaft has a diameter of 14
mm, determine the displacement of the tooth P on gear A.
Segment AC
150-TAC=0
TAC=150 N.m
Segment CD
150-280+TCD=0
TCD=130 N.m
Segment DE
-130-40+TDE=0
TDE=170 N.m
TL
GJ
1
=
GJ
TL
=
1
150 0.4 130 0.3 170 0.5
3 4
80 10 (7 10 )
9
=-0.21211 rad
32
Example 25: A steel shaft ABC connecting three gears consists of a solid bar of diameter d
between gears A and B and a hollow bar of outside diameter 1.25d and inside diameter d
between gears B and C. Both bars have length 0.6 m. The gears transmit torques T1=240
N.m, T2=540 N.m, and T3=300 N.m acting in the directions shown in the figure. The shear
modulus of elasticity for the shaft is 80 GPa. a) what is the minimum permissible diameter
d if the allowable shear stress in the shaft is 80 MPa?. b) what is the minimum permissible
diameter d if the angle of twist between any two gears is limited to 4 ?.
TAB=240 N.m
TBC=300 N.m
a)
1. For solid bar AB
4
J= d
32
T d / 2 T AB d / 2
AB
J 4
d
32
240 d / 2
80 10 6
4
d
32
16 240
d3
80 10 6
d=0.02481 m
d=24.81 mm
2. For hollow bar BC
J= [ d o4 d i4 ] [(1.25d ) 4 d 4 ]
32 32
TBC 1.25 d / 2 T 1.25 d / 2
BC
J
[(1.25d ) 4 d 4 ]
32
300 1.25 d / 2 16 300 1.25
80 10 6 d3
80 10 6 1.4414
[(1.25d ) 4 d 4 ]
32
d=0.0255 m
d=25.5 mm Answer
b)
1. For solid bar AB
TAB L
GJ
33
240 0.6
4
180
80 10 9 d 4
32
d=0.02263 m
d=22.63 mm
TBC L
GJ
300 0.6
4
180
80 10 9 [(1.25d ) 4 d 4 ]
32
d=0.02184 m
d=21.84 mm
d=0.02263 m
d=22.63 mm Answer
Example 26: The shaft is subjected to a distributed torque along its length of t=10x2
N.m/m, where x is in meters. If the maximum stress in the shaft is to remain constant at 80
MPa, determine the required variation of the radius r of the shaft for 0 x 3 m
T tdx
10 3
10 x 2 dx x
3
Tr
max
J
10 3
x r
20 x 3
80 10 6 3 80 10 6
4 3r 3
r
2
34
20 x 3
r3 0.002982 x m
3 80 10 6
r=2.982 x mm
Example 26: The shaft has a radius 50 mm and is subjected to a torque per unit length of
100 N.m which is distributed uniformly over the shafts entire length 2 m. If it is fixed at its
far end A, determine the angle of twist of end B. The shear modulus is 73.1 GPa.
2m
100 N .m / m
T(x)=100x
2 2
T ( x)dx 100 xdx
GJ
0 0 73.1 10 9 (50 10 3 ) 4
2
2
200 x2
73.1 10 9 (50 10 3 ) 4 2 0
400
73.1 10 (50 10 3 ) 4
9
2.786 10 4 rad
=0.01596o
35
Statically Indeterminate:
TA-T+TB=0
TA +TB=T
A/B=0
T A L AC TB LBC
0
GJ GJ
If T1>T2
-TA-T2+T1-TB=0
T2
TB L1 (TA T2 ) L2 TA L3
0 L3
GJ GJ GJ
T1
L2
L1
T2
T2
T1
T2
36
Example 27: The solid steel shaft shown has a diameter of 20 mm. If it is subjected to the
two torques, determine the reactions at the fixed supports A and B.
-TB+800-500-TA=0
TB+TA=300 …………………………………....(1)
-0.2TB+1.5TA+750+0.3TA=0
1.8TA-0.2TB=-750 …………………………...…(2)
TA=-345 N.m
TB=645 N.m
37
Example 28: The shaft shown below is made from steel tube, which is bonded to a brass
core. If a torque of T=250 lb.ft is applied at its end, plot the shear stress distribution along a
radial line of its cross sectional area. Take Gst11.4×103 ksi, Gbr=5.2×103 ksi.
Tst+Tbr=250×12=3000 lb.in………….(1)
θ=θst=θbr
Tst L Tbr L
11.4 10 6 [(1) 4 (0.5) 4 ] 5.2 10 6 [(1) 4 (0.5) 4 ]
2 2
Tst=32.88Tbr……………………….(2)
From (1) and (2)
Tst=2911 lb.in=242.6 lb.ft
Tbr=88.5 lb.in=7.38 lb.ft
88.5 0.5
( br ) max 451 psi
(0.5) 4
2
2911 1
( st ) max 1977 psi
[(1) (0.5) ]
4 4
2
2911 0.5
( st ) min 988 psi
[(1) (0.5) ]
4 4
451 988
0.0867 10 3 rad
G 5.2 10 6
11.4 10 6
38
Torsion of Solid Noncircular Shafts:
4.81T 7.1TL
a Square a3 a 4G
a a 20T 46TL
Equilateral
a3 a 4G
triangle
a
b 2T (a 2 b 2 )TL
b Ellipse ab 2 a 3 b 3 G
a a
Example 28: The 2014-T6 aluminum strut is fixed between the two walls at A and B. If it
has a 2 in by 2 in square cross section and it is subjected to the torsional loading shown,
determine the reactions at the fixed supports. Also what is the angle of twist at C. Take
G=3.9×103 ksi.
TA-40-20+TB=0
TA+TB=60 ……….(1)
A/B=0
7.1TL
A/ B
a 4G
39
TA
TA-2TB=-20 ………………(2) 40 lb. ft
7.1T A L
C
a 4G
7.1 33.333 12 2 12
C
2 4 3.9 10 6
C=0.001092 rad
C=0.06258º
The forces acting on the two faces are dFA=A(tAdx) , dFB=B(tBdx), these
forces are equal for equilibrium, so that:
AtA=BtB
q=avgt
40
Average shear stress(avg):
1
Area of triangle dAm= hds
2
hds=2dAm
T
avg=
2tAm
avg: The average shear stress acting over the thickness of the tube.
T: The resultant internal torque at the cross section.
t: The thickness of the tube where avg is to be determined.
Am: The mean area enclosed within the boundary of the center line of the tube thickness.
T
q=avgt=
2 Am
Angle of Twist():
TL ds
2
4 AmG t
41
Example 29: The tube is made of C86100 bronze and has a rectangular cross section as
shown below. If its subjected to the two torques, determine the average shear stress in the
tube at points A and B. Also, what is the angle of twist of end C? The tube is fixed at E.
Take G=38 GPa.
60-25-T=0
T=35 N.m
Am=(40×10-3-5×10-3)(60×10-3-3×10-3)
=0.001995 m2
T 35
A= = 3
2tAm 2 5 10 0.001995
A=1.7543859 MPa
T 35
B= = 3
2tAm 2 3 10 0.001995
B=2.9239766 MPa
TL ds
2
4 Am G t
60 0.5 35 10 3 57 10 3
= [ 2 2 ]
4 (0.001995 ) 2 3.8 10 9 3 10 3 5 10 3
35 1.5 35 10 3 57 10 3
[ 2 2 ]
4 (0.001995 ) 2 3.8 10 9 3 10 3 5 10 3
=0.0062912 rad
42
Example 30: A thin tube is made from three 5 mm thick A-36 steel plates such that it has a
cross section that is triangular as shown below. Determine the maximum torque T to which
it can be subjected, if the allowable shear stress is allow=90 MPa and the tube is restricted
to twist no more than =2×10-3 rad. Take G=75 GPa.
1
A= (200×10-3)× (200×10-3 sin60)=0.01732 m2
2
t=0.005 m
T T
allow= = 3
=90×106
2tAm 2 5 10 0.01732
T=15.588 KN.m
TL ds
2
4 AmG t
T 3 200 10 3
2×10-3= [3 ]
4 (0.01732) 2 75 10 9 5 10 3
T=500 N.m
43
Thin Walled Cylinder, Thin Walled Pressure Vessels:
Cylindrical or spherical vessels are commonly used in industry to serve as boilers
or tanks. When under pressure, the material of which they are made is subjected to a
loading from all directions. In general "thin wall" refers to a vessel having an inner radius
to wall thickness ratio of 10 or more (r/t 10)
1. Cylindrical Vessels:
Consider the cylindrical vessel having a wall thickness t and inner radius r as
shown below. A pressure p is developed within the vessel by a containing gas or fluid,
which is assumed to have negligible weight.
2[1(tdy)]-p(2rdy)=0
pr
1
t
2(2rt)-p(r2)=0
pr
2
2t
44
e. Change in length
The change in length of the cylinder may be determined from the
longitudinal strain.
Change in length=longitudinal strain×original length
1
L=ε2L= ( 2 1 ) L
E
pr
L= (1 2 ) L
2tE
f. Change in diameter
The change in diameter may be found from the circumferential change.
Change in diameter=diametral strain×original diameter
Diametral strain=circumferential strain
1
d= ε1d= ( 1 2 ) d
E
pr
d= (2 ) d
2tE
1
εv= ( 2 1 2 1 2 2 ) longitudinal strain
E
1 pr pr pr pr
= ( 2 ) diametral strain
E 2t t t t
pr
εv= (5 4 )
2tE
45
2. Spherical Vessels:
Because of the symmetry of the sphere the stresses set up owing to internal
pressure will be two mutually perpendicular hoop or circumferential stress of equal
value and a radial stress.
1(2rt)-p(r2)=0
pr
1
2t
pr
2= 1
2t
1 3 1 3 pr
εv= ε1=3 ( 1 2 ) = (1 ) = (1 )
E E 2tE
v= εvv
3 pr
v = (1 ) v
2tE
46
Cylindrical Vessels with Hemispherical Ends:
r=d/2
1 1 Pr Pr
1 ( 1 2 ) = ( )
E E tc 2t c
pr
ε1= (2 ) hoop strain
2t c E
Pr
1 hoop stress
2t s
1
1 ( 1 2 ) = 1 (1 )
E E
pr
ε1= (1 ) hoop strain
2t s E
Thus equating the two strains in order that there shall be no distortion of the
junction.
pr pr
(1 ) = (2 )
2t s E 2t c E
ts 1
tc 2
47
Example 31: A thin cylinder 75 mm internal diameter, 250 mm long with walls 2.5 mm
thick is subjected to an internal pressure of 7 MN/m2. Determine the change in internal
diameter and the change in length. If in addition to the internal pressure, the cylinder is
subjected to a torque of 200 N.m find the magnitude and nature of the stresses set up in the
cylinder.E=200 GN/m2, υ=0.3.
pr
d= (2 ) d
2tE
75
7 10 6 10 3
d= 3
2 [2 0.3] 75 10 3
2 2.5 10 200 10 9
d=33.468×10-6 m=33.468 μm
pr
L= (1 2 ) L
2tE
75
7 10 6 10 3
L= 2 [1 2 0.3] 250 10 3
2 2.5 10 3 200 10 9
L=26.25×10-6 m=26.25 μm
75
7 10 6 10 3
pr 2
1 =
t 2.5 10 3
1=105×106 N/m2=105 MN/m2
75
7 10 6 10 3
pr 2
2 =
2t 2 2.5 10 3
Tr Tr 200 40 10 3
= =
J 4
[ro ri ]
4
[(40 10 3 ) 4 (37.5 10 3 ) 4 ]
2 2
=8.743862 MN/m2
48
Example 32: A cylinder has an internal diameter of 230 mm, has walls 5 mm thick and is 1
m long. It is found to change in internal volume by 12×10-6 m3 when filled with a liquid at
a pressure p. If E=200 GN/m2 and υ=0.25, and assuming rigid end plates, determine a) the
values of hoop and longitudinal stresses b) the necessary change in pressure p to produce a
further increase in internal volume of 15%.
pr
a) v= (5 4 ) v
2tE
230
p 10 3
-6 2 230
12×10 = 3
[5 4 0.25] ( 10 3 ) 2 1
2 5 10 200 10 9
2
p=1.255763 MN/m2
230
1.255763 10 6 10 3
pr 2
1 =
t 5 10 3
1=28.882549 MN/m2
230
1.255763 10 6 10 3
pr 2
2 =
2t 2 5 10 3
2=14.4412745 MN/m2
b) v=1.15×12×10-6=13.8×10-6 m3
pr
v= (5 4 ) v
2tE
230
10 3
p
-6 2 230
13.8×10 = 3
[5 4 0.25] ( 10 3 ) 2 1
2 5 10 200 10 9
2
p=1.444128 MN/m2
49
Vessels Subjected to Fluid Pressure:
If a fluid is used as the pressurization medium the fluid itself will change in
volume as pressure is increased and this must be taken into account when calculating the
amount of fluid which must be pumped into the cylinder in order to raise the pressure by a
specific amount.
The bulk modulus of a fluid is defined as:
Volumetric stress
bulk modulus k=
Volumetric strain
volumetric stress=pressure p
change in volume v
volumetric strain= =
original volume v
p pv
k= =
v v
v
pv
change in volume of fluid under pressure=
k
extra fluid required to raise cylinder pressure by p
pr pv
= (5 4 ) v+
2tE k
3 pr pv
= (1 ) v+
2tE k
50
Example 33: a) A sphere 1m internal diameter and 6 mm wall thickness is to be pressure
tested for safety purposes with water as the pressure medium. Assuming that the sphere is
initially filled with water at atmospheric pressure, what extra volume of water is required
to be pumped in to produce a pressure of 3 MN/m2 gauge? For water k=2.1 GN/m2
b) The sphere is now placed in service and filled with gas until there is a volume change of
72×10-6 m3. Determine the pressure exerted by the gas on the walls of the sphere. c) To
what value can the gas pressure be increased before failure occurs according to the
maximum principal stress theory of elastic failure? E=200 GPa, υ=0.3 and the yield stress
is simple tension=280 MPa.
3 pr pv
a) extra volume of water= (1 ) v+
2tE k
4
3 10 6 (0.5) 3
3 3 10 0.5
6
4 3
= 3
(1 0.3) (0.5) 3
2 6 10 200 10 9
3 2.1 10 9
=0.001435221 m3
3 pr
b) v= (1 ) v
2tE
3 p 0 .5 4
72×10-6= 3
(1 0.3) (0.5) 3
2 6 10 200 10 9
3
p=0.31430827 MN/m2
pr
1 1=yield stress for maximum principal stress theory
2t
p 0 .5
280×106=
2 6 10 3
p=6.72 MN/m2
51
Shear and Moment Diagram:
Beams are long straight members that carry loads perpendicular to their
longitudinal axis. They are classified according to the way they are supported, e.g. simply
supported, cantilevered, or overhanging.
P P
Cantilevered beam
Types of Loading:
Loads commonly applied to a beam may consist of concentrated forces(applied at
a point), uniformly distributed loads, in which case the magnitude is expressed as a certain
number of newtons per meter of length of the beam, or uniformly varying loads. A beam
may also be loaded by an applied couple.
100 N
(point load)
(concentrated force)
52
10 N / m 5 N / m
4m 5m
Shearing force and bending moment diagrams show the variation of these
quantities along the length of a beam for any fixed loading condition. At every section in a
beam carrying transverse loads there will be resultant forces on either side of the section
which, for equilibrium, must be equal and opposite.
Shearing force at the section is defined as the algebraic sum of the forces taken on
one side of the section. The bending moment is defined as the algebraic sum of the
moments of the forces about the section, taken on either side of the section.
Sign Convention:
Forces upwards to the left of a section or downwards to the right of a section are
positive. Clockwise moments to the left and counter clockwise to the right are positive.
M M M M
V V V - V -
Procedure of Analysis:
The shear and moment diagrams for a beam can be constructed using the
following procedure:-
1. Determine all the reactive forces and couple moments acting on the beam, and
resolve all the forces into components acting perpendicular and parallel to the beam's
axis.
2. Specify separate coordinates x having an origin at the beam's left end extending to
regions of the beam between concentrated forces and/or couple moments, or where
there is no discontinuity of distributed loading.
3. Section the beam perpendicular to its axis at each distance x, and draw the free body
diagram of one of the segments. Be sure V and M are shown acting in their positive
sense, in accordance with the sign convention given as above.
4. The shear is obtained by summing forces perpendicular to the beam's axis.
5. The moment is obtained by summing moment about the sectioned end of the
segment.
53
6. Plot the shear diagram(V versus x) and the moment diagram(M versus x). If
numerical values of the functions describing V and M are positive, the values are
plotted above the x-axis, whereas negative values are plotted below the axis.
Example 33: Draw the shear and moment diagrams for the beam shown below.
P P
A B Ax B
C
Ay Cy
L/2 L/2
F x 0
Ax=0
M C 0
P×L/2-Ay×L=0
Ay=P/2
F y 0
Cy+Ay-P=0
Cy=P/2
Segment AB
F y 0 V M
P P
-V=0 x
2 2
P
V=
2
M 0
P
M- ×x=0
2 P
P
M= x
2
Segment BC V
M
P
2 x
Fy 0
54
P
-P-V=0
2
P
V=-
2
M 0
P L
M- ×x+P(x- )=0
2 2
P
M= (L-x) P
2
B
P P
2 2
P
2
S.F. diagram
P
PL 2
M max
4
B.M. diagram
55
Example 34: Draw the shear and moment diagrams for the beam shown below.
10 KN 20 KN 30 KN
2m 4m 2m
A B C D E F
4m 8m
20 KN
10 KN 20 KN 30 KN
Fx 0
Fx=0 2m 4m 2m
M F 0
-Ay×12+10×10-20×8+20×6 A B C D E F
Fx
+30×2=0
Ay=10 KN
F
Fy
y 0 Ay 4m 8m
20 KN
10-10+20-20-30+Fy=0
Fy=30 KN
Segment AB 0 x2
F y 0
10-V=0
V=10 KN
M 0
M-10×x=0
M=10x
10 KN
Segment BC 2 x4
F y 0 V M
10-10-V=0
V=0
M 0
x
M-10x+10(x-2)=0 10 KN
M=20 KN.m
Segment CD 4 x6
F y 0
56
10 KN
10-10+20-V=0
V=20 KN
M
M 0
V
M-10x+10(x-2)-20(x-4)=0 20 KN
M=20(x-3) x
10 KN
Segment DE 6 x 10
F y 0 10 KN 20 KN
10-10+20-20-V=0
V=0
M 0 V M
M-10x+10(x-2)-20(x-4)+20(x-6)=0
20 KN
M=60 KN.m
x
10 KN
Segment EF 10 x 12
F y 0
10-10+20-20-30-V=0
V=-30 KN
M 0
M-10x+10(x-2)-20(x-4)+20(x-6)
+30(x-10)=0
M=30(12-x) 10 KN 20 KN 30 KN
V M
20 KN
x
10 KN
57
58
Example 35: Draw the shear and moment diagrams for the beam shown below.
w
A B
F x 0 wL
Ax=0
M B 0 A B
L
wL -AyL=0 Ax
2
wL
Ay= L
2 Ay By
Fy 0
wL
+By-wL=0
2 wx
wL
By= x/2
2 w
Fy 0 V M
wL
-wx-V=0
2 x
L
V=-w(x- ) wL
2
2
M 0
wL x dM
M- x+wx( )=0 Maximum moment occur when 0
2 2 dx
w
M= (xL-x2) dM w
( L 2 x) 0
2 dx 2
L 2x 0
L
x
2
Location of maximum moment
59
w
A B
wL
wL
L 2
2
wL
2
S.F Diagram
L/2
wL2
M max
8
B.M Diagram
L/2
60
Example 36: Draw the shear and moment diagrams for the beam shown below.
wo
A B
wo L
Fx 0 2
Ax=0
F y 0 MA
wo L Ax
Ay=
2
M A 0
wo L 2 Ay 2 1
MA- L =0 L L
2 3 3 3
w L2
MA= o
3
wo x2
x
2L w wo
L
wo L2
F y 0
3
V M
2 x/3
wo L wo x
- -V=0
2 2L x
wo L
w x2
V= o (L- ) 2
2 L
dV
w L Maximum shear force occur at 0
Vmax= o dx
2
dV w x
o 0
dx L
x=0
M 0
wo L2 wo L wo x 2 1
M+ - x+ x =0
3 2 2L 3
61
wo
M= (3L2x-x3-2L3)
6L 2
wo L
Mmax=
3
wo
2
wo L
3
L
wo L
2
wo L
2
S.F Diagram
wo L2
3
62
Example 37: The horizontal beam AD is loaded by a uniform distributed load of 5 KN per
meter of length and is also subjected to the concentrated force of 10 KN applied as shown
below. Determine the shearing force and bending moment diagrams.
F x 0 10 KN
Ax=0 B 5 KN / m
M A 0 A
D
Cy×3-30×2=0 C
Cy=20 KN
F y 0
2m 1m 1m
Ay+20-30=0
Ay=10 KN 20 KN 10 KN
Ax
Ay Cy
Segment AB 0 x2
5x
F y 0 5 KN / m
x/2
10-5x-V=0 V M
V=10-5x
M 0 x
x
M-10x+5x =0 10 KN
2
x
M=5x(2- )
2
Segment BC 2 x3 10 KN
5x
F y 0
5 KN / m
x/2
10-5x-10-V=0 V M
V=-5x
M 0 x
x
M-10x+5x +10(x-2)=0 10 KN
2
5
M=20- x2
2
Segment CD 3 x 4
63
10 KN
5x
x/2
F y 0 5 KN / m
V M
10-5x-10+20-V=0
V=20-5x
M 0 x
20 KN
x 10 KN
M-10x+5x +10(x-2)-20(x-3)=0
2
5
M=-40+20x- x2 10 KN
2
B 5 KN / m
A
D
C
2m 1m 1m
10 KN 20 KN
10 KN
5 KN
S.F Diagram
10 KN
15 KN
10 KN .m
B.M Diagram
2.5 KN .m
`
64
Example 38: A beam ABC is simply supported at A and B and has an overhang BC. The
beam is loaded by two forces P and a clockwise couple of moment Pa that act through the
arrangement shown. Draw the shear force and bending moment diagrams for beam ABC.
P P
Pa
A C
B
a a a a
M D 0 P P
-Pa+RC(2a)-Pa=0 Pa
RC=P
F y 0
RD+P-P-P=0
RD=P P
RD RC
M A 0 P
RB(2a)-Pa-P(3a)=0
RB=2P
F y 0
RA+2P-P-P=0
RA=0 RA RB
Segment AD 0 xa
F y 0
V=0
M 0 V M
M=0
x
V
Segment DB a x 2a
65
F y 0
-V-P=0
V=-P
M 0 P
M+P(x-a)=0
M=P(a-x) V
Segment DB 2a x 3a
x
Fy 0 2P
2P-P-V=0
V=P
M 0
M+P(x-a)-2P(x-2a)=0 P P
M=P(x-3a)
2P
S.F. Diagram
P
B.M. Diagram
Pa
66
Graphical Method for Constructing Shear and Moment Diagram:
w(x )
dV
w(x)
dx
Slope of shear diagram at each point=-distributed load intensity at each point.
dM
V
dx
Slope of moment diagram at each point=shear at each point.
When the force acts downward on the beam, V is negative so the shear will jump
downward. Likewise, if the force acts upward, the jump will be upward.
If moment Mo is applied clockwise on the beam, M is positive so the moment
diagram will jump upward. Likewise, when Mo acts counterclockwise, the jump will
be downward.
67
Example 39: Draw the shear and moment diagrams for the beam shown below.
P
Fx 0
Ax=0 A
Fy 0
Ay-P=0 L
Ay=P
M A 0 P
M
M-PL=0
M=PL Ax
Ay
At x=0 V=P
At x=L V=P P
At x=0 M=-PL
At x=L M=0
PL
68
Example 40: Draw the shear and moment diagrams for the beam shown below.
15 KN / m
10 KN.m
M A 0 A B
By×5.5-10-60×2=0
By=23.63 KN
F y 0
4m 0 .5 m 1m
23.63+Ay-60=0
Ay=36.37 Kn 15 KN / m
F x 0 10 KN.m
Ax=0 Ax
Ay By
4m 0 .5 m 1m
15 KN / m
10 KN.m
36.37 KN 23.63 KN
4m 0 .5 m 1m
36.37 KN
4 x
x 4 x x
36.37 23.63 23.63 KN
23.63x=36.37×4-36.37x 23.63 KN
x=2.4246 m
Maximum bending moment occur 25.48 KN.m
when V=0, at x=2.4246 m 23.665 KN.m
44.092 KN.m
13.665 KN.m
69
Example 41: Draw the shear and moment diagrams for the beam shown below.
48 KN / m
10 KN / m
M C 0 A B 80 KN .m
C
80-RB×6+30×7.5+144×4=0
3m 6m
RB=146.83 KN
F y 0
30 KN 144 KN
RC+146.83-30-144=0
1.5 m 2m
RC=27.17 KN
80 KN.m
RB RC
48 KN / m
10 KN / m
C
A B 80 KN .m
146 .83 KN 27.17 KN
3m 6m
116 .83 KN
For segment 3 x 6
V=116.83+4(x-3)2-48(x-3)
Maximum bending moment occur when
V=0 3.39375 m
0=116.83+4(x-3)2-48(x-3)
x2-18x+74.2075=0
x=6.39375 m from left end 47.187 KN .m 27.17 KN
30 KN
45 KN .m
125 KN .m
70
Example 42: Draw the shear and moment diagrams for the beam shown below.
3 KN / m
F x 0 A B
C
Ax=0 3m 3m 3m
M A 0
By×6-9×7=0
By=10.5 KN 9 KN
F y 0 2m 3 KN / m
Ay+10.5-9=0 Ax
Ay=-1.5 KN
Ay By
3 KN / m
1.5 KN
10.5 KN
6.75 KN
1.5 KN
3.75 KN
4.5 KN.m
11.25 KN.m
71
Stresses in Beams:
Pure bending refers to flexure of a beam under a constant bending moment.
Therefore, pure bending occurs only in regions of a beam where the shear force is zero.
Nonuniform bending refers to flexure in the presence of shear forces, which means that the
bending moment changes as we move along the axis of the beam.
P P
a a
P
S.F. Diagram
P
Pa
B.M. Diagram
Assumptions:
1. The beam is initially straight and unstressed.
2. The material of the beam is perfectly homogeneous.
3. The elastic limit is nowhere exceeded.
4. Young's modulus for the material is the same in tension and compression.
5. Plane cross-sections remain plane before and after bending.
6. Every cross-section of the beam is symmetrical about the plane of bending i.e. about
an axis perpendicular to the N.A.
7. There is no resultant force perpendicular to any cross-section.
72
As a result of this bending the top fibers of the beam will be subjected to
compression and the bottom to tension. Its reasonable to suppose, that somewhere between
the two there are points at which the stress is zero, these points is termed the neutral axis.
The neutral axis will always pass through the centre of area or centroid.
The length L1 of the line ef after bending takes place is:
L1=(-y)d
dx
d=
y
L1=(1- )dx
The original length of line ef is dx
y
(1 )dx dx
L1 original length y
Strain(εx)= = =-
original length dx
εx=-ky
where k is the curvature.
The longitudinal normal strain will vary linearly with y from the neutral axis. A
contraction (-εx) will occur in fibers located above the neutral axis (+y), whereas
elongation (+εx) will occur in fibers located below the neutral axis (-y).
max
εx
N.A
y
εx=-( ) εmax
c1
By using Hook's law x=Eεx
E
x=-Eky=- y
73
max
N.A
y
x=-( ) max
c1
Normal stress will vary linearly with y from the neutral axis. Stress will vary from
zero at the neutral axis to a maximum value max a distance c1 farthest from neutral axis.
N.A.
dF=xdA
M= ydF = ( x dA) y
A A
y
= ( max ) ydA
A
c1
max
y
2
M= dA
c1 A
y
2
dA =I moment of inertia
A
Mc1
max
I
max: The maximum normal stress in the member, which occurs at a point on the cross
sectional area farthest away from the neutral axis.
M: The resultant internal moment.
I: The moment of inertia of the cross sectional area computed about the neutral axis.
c1: The perpendicular distance from the neutral axis to a point farthest away from the
neutral axis, where max acts.
74
Mc1 Mc2
1=- , 2=
I I
M M
1=- , 2=
S1 S2
I I
S1= , S2=
c1 c2
The quantities S1 and S2 are known as the section moduli of the cross sectional
area.
Example 43: A simple beam AB of span length L=22 ft supports a uniform load of
intensity q=1.5 k/ft and a concentrated load P=12 k. The uniform load includes an
allowance for the weight of the beam. The concentrated load acts at a point 9 ft from the
left hand end of the beam. The beam is constructed of glued laminated wood and has a
cross section of width b=8.75 in and height h=27 in. Determine the maximum tensile and
compressive stresses in the beam due to bending.
P 12 k
9 ft
q 1.5 k / ft
A B
22 ft
75
12 k 33 k
Ay By
M A 0
By×22-12×9-33×11=0
By=21.409 k
F y 0
Ay+21.409-12-33=0
Ay=23.591 k
P 12 k
9 ft
q 1.5 k / ft
23.591 k 21.409 k
23.591 k
10.091 k
S.F. Diagram
1.909 k
Maximum bending moment
21.409 k
Mmax=151.569 k.ft
=151.569×12 151.569 k. ft
=1818.828 ksi
B.M. Diagram
76
c1=c2=13.5 in
Mc
1= 1
I
bh 8.75 (27) 3
3
I= = 14352.1875 in 4 c1
12 12 27 in
1818.828 103 13.5
1= c2
14352.1875
=-1710.8317 psi
1818.828 103 13.5
1= 8.75 in
14352.1875
=1710.8317 psi
Example 44: The simply supported beam has the cross sectional area shown below.
Determine the absolute maximum bending stress in the beam and draw the stress
distribution over the cross section at this location.
20 mm
5 KN / m
A B
300 mm
20 mm
20 mm
6m
30 KN
250 mm
Ay
By
77
M A 0 5 KN / m
By×6-30×3=0
By=15 KN
F y 0
Ay+15-30=0
Ay=15 KN 15 KN 15 KN
15 KN
15 KN
20 mm
1
2
300 mm
N.A
20 mm
20 mm
c1=c2=170 mm
bh 3 3
I1 = Ad 2
12
250 mm
250 10 3 (20 10 3 ) 3
I1 = (250 10 20 10 ) (160 10 3 ) 2
3 3
12
I1=128.16667×10-6 m4
I3=I1=128.16667×10-6 m4
bh 3 (20 10 3 ) (300 10 3 ) 3
I2 = = =45×10-6 m4
12 12
I= I1+ I2+ I3=128.16667×10-6+128.16667×10-6+45×10-6
I=301.333×10-6 m4
Mc1 22.5 10 3 170 10 3
max= =
I 301.333 10 6
=12.693598 MPa.
78
B
My B
B=
I
22.5 10 3 150 10 3
=
301.333 10 6
=11.200233 MPa.
Example 45: The beam shown below has a cross section of channel shape with width
b=300 mm and height h=80 mm, the web thickness is t=12 mm. Determine the maximum
tensile and compressive stresses in the beam due to uniform load.
300 mm
3.2 KN / m
80 mm
A
12 mm B
3m 1.5 m
M A 0
By×3-14.4×2.25=0
By=10.8 KN 14.4 KN
F y 0
Ay+10.8-14.4=0 Ax
Ay=3.6 KN
F x 0
Ay By
Ax=0
3.2 KN / m
79
3.6 KN 10.8 KN
3.6 KN 4.8 KN
M1=2.025 KN.m 6 KN
M2=3.6 KN.m 2.025 KN.m
3.6 KN.m
300 mm
yc
yA
A 2
1 3 80 mm
12 mm
321888 10 9
yc 6
=61.52×10-3 m
5232 10 300 mm
yc=61.52 mm
c 2 18.48 mm
80 mm
c1 61.52 mm 12 mm
bh 3
I1 = Ad 2
12
80
12 10 3 (80 10 3 ) 3
I1 = +960×10-6×(21.52×10-3)2=0.95658×10-6 m4
12
I3= I1=0.95658×10-6 m4
bh 3
I2 = Ad 2
12
276 10 3 (12 10 3 ) 3
I2 = +3312×10-6×(12.48×10-3)2=0.55558×10-6 m4
12
I= I1+ I2+ I3=2.46874×10-6 m4
M 1c 2 2.025 10 3 61.52 10 3
( t )1 50.462179 MPa
I 2.46874 10 6
M c 3.6 10 3 18.48 10 3
( t ) 2 2 1 26.94815 MPa
I 2.46874 10 6
(t)max=50.462179 MPa
M 1c1 2.025 10 3 18.48 10 3
( c )1 15.158339 MPa
I 2.46874 10 6
M 2 c2 3.6 10 3 61.52 10 3
( c ) 2 89.71054 MPa
I 2.46874 10 6
(c)max=-89.71054 MPa
Composite Beams:
Composite beams are made from different materials in order to efficiently carry a
load.
dF=dA=( E1ε)dydz
If the material 1 is being transformed into material 2
b2=nb
81
dF dA =( E2ε)ndydz
dF= dF
( E1ε)dydz=( E2ε)ndydz
E1
n=
E2
n: transformation factor (modular ratio).
E2
b1= n b where n =
E1
For the transformed material
=n
82
Example 46: A composite beam is made of wood and reinforced with a steel strap located
on its bottom side. It has the cross sectional area shown below. If the beam is subjected to a
bending moment of M=2 KN.m determine the normal stress at point B and C. Take Ew=12
GPa and Est=200 GPa.
B
Ew
n
E st
12 150 mm
n 0.06
200
bst n bw
bst 0.06 150 9 mm
20 mm
C
150 mm
9 mm
9 mm
B
2
150 mm
150 mm
20 mm
1 20 mm
C
150 mm 150 mm
83
No. of Area A(m2) y (m)
3
yA (m )
1 3000×10-6 10×10-3 30000×10-9
2 1350×10-6 95×10-3 128250×10-9
A =4350×10 yA =158250×10
-6 -9
9 mm
yc
y A
A
158250 10 9 c1 133.621 mm 150 mm
yc 3
36.379 10 3 m
4350 10
36.379 mm N. A
I=I1+I2
bh 3 c 2 36.379 mm
I1 Ad 2 20 mm
12
150 10 3 (20 10 3 ) 3
I1 3000 10 6 (26.379 10 3 ) 2
12 150 mm
I1=2.187554×10-6 m4
bh 3
I2 Ad 2
12
9 10 3 (150 10 3 ) 3
I2 1350 10 6 (58.621 10 3 ) 2
12
I2=7.170419×10-6 m4
I=9.35797×10-6 m4
My
B
I
2 10 3 133.621 10 3
B 28.557689 MPa
9.35797 10 6
B n B
B 0.06 (28.557689) 1.71346134 MPa
My
B
I
2 10 3 36.379 10 3
B 7.774976 MPa
9.35797 10 6
84
Shear Stresses in Beams
V
It ydA
A
ydA y A = Q
A
VQ
It
:- the shear stress in the member at the point located a distance y from the neutral axis.
V:-the internal resultant shear force.
I:-the moment of inertia of the entire cross sectional area computed about the neutral axis.
t:-the width of the members cross sectional area, measured at the point where is to be
determined.
Q y A , where A is the top (or bottom) portion of the members cross sectional area,
defined from the section where t is measured, and y is the distance to the centroid of A ,
measured from the neutral axis.
85
Example 47: A metal beam with span L=3 ft is simply supported at points A and B. The
uniform load on the beam is q=160 lb/in. The cross section of the beam is rectangular with
width b=1 in and height h=4 in. Determine the normal stress and shear stress at point C,
which is located 1 in below the top of the beam and 8 in from the right hand support.
q 160 lb / in
M A 0 A C B
By×3×12-5760×1.5×12=0
By=2880 lb
F y 0
3 ft
Ay+2880-5760=0
Ay=2880 lb
q 160 lb / in 5760 lb
2880 lb 2880 lb
Ay By
2880 lb
8 in
18 in
V
2880 lb
18 in V 2880
10 18
V=1600 lb
86
At point C x=28 in from left end
from shear force diagram
A 1 in
y
N.A
4 in
1 1
M 2880 18 1600 10
2 2
M=17.92 k.in
bh 3 1 (4) 3
I 5.3333 in 4
12 12 1 in
2
A =1×1=1 in
y =1.5 in
Q y A =1.5×1=1.5 in3
My 17920 1
C 3.36 ksi
I 5.3333
VQ
It
1600 1.5
450 psi
5.3333 1
87
Example 48: Consider the cantilever beam subjected to the concentrated load shown
below. The cross section of the beam is of T-shape. Determine the maximum shearing
stress in the beam and also determine the shearing stress 25 mm from the top surface of the
beam of a section adjacent to the supporting wall. 50 mm
50 KN
2m
M A 0
A B 125 mm
M-50×2=0
M=100 KN.m
F y 0
2m
50 KN
50 mm
Ay-50=0
Ay=50 KN M
B 200 mm
Ay
50 KN
2m
B
100 KN.m
50 KN
50 KN
S.F. Diagram
B.M. Diagram
100 KN.m
50 mm
50 mm 1
200 mm
88
No. of Area A(m2) y (m) yA (m )
3
yc
y A
A
50 mm
953125 10 9
yc 3
58.65 10 3 m
16250 10
c1 116.35 mm
58.65 mm 125 mm 2
N. A
1 c2 58.65 mm
50 mm
I=I1+I2
bh 3
I1 Ad 2 200 mm
12
200 10 3 (50 10 3 ) 3
I1 10000 10 6 (33.65 10 3 ) 2
12
I1=13.40655833×10-6 m4
bh 3
I2 Ad 2
12
50 10 3 (125 10 3 ) 3
I2 6250 10 6 (53.85 10 3 ) 2
12
I2=26.26191146×10-6 m4
I=39.6684×10-6 m4
50 mm
Q y A
-3 -3 A
A =50×10 ×116.35×10
c1 116.35 mm
=0.0058175 m2 125 mm 2
-3
y =58.175×10 m
y
N. A
Q=0.000338433 m3 1 c2 58.65 mm
50 mm
VQ
max
It
50 10 3 0.000338433 200 mm
max 8.5315553 MPa
39.6684 10 6 50 10 3
89
50 mm
Q y A A
-3 -3 25 mm
A =50×10 ×25×10 c1 116.35 mm
125 mm
=0.00125 m2 y
-3
y =103.85×10 m
N. A
Q=0.000129812 m3 50 mm 1 c2 58.65 mm
VQ
200 mm
It
50 10 3 0.000129812
3.272441 MPa
39.6684 10 6 50 10 3
90
Curved Beams
Due to the curvature of the beam, the normal strain in the beam does not vary linearly with depth as in the
case of a straight beam .As result, the neutral axis does not pass through the centroid of the cross section.
C7
If we isolate a differential segment of the beam let a strip material located at r distance has an original length
r dθ .Due to the rotations δθ/2, the strip's total change in length is δθ)R-r(
( R r ) Rr
,k k( )
rd d r
Strain is a nonlinear function of r, in fact it varies in a hyperbolic fashion .Hooke's law applies,
Rr
Ek ( )
r
F R 0
Rr
dA 0
A
Ek (
A
r
) dA 0
dA
R dA 0
A
r A
91
A
R
dA
A r
R-:The location of the neutral axis, specified from the center of curvature 0' of the member.
A-:The cross -sectional area of the member.
r -:The arbitrary position of the area element dAon the cross section, specified from the center of
curvature 0' of the member.
My
Ae( R y )
y=R-r , e= r -R
σ -:The normal stress in the member.
M -:The internal moment, determined from the method of sections equations of equilibrium and computed about
the centroidal axis .
A -:The cross-sectional area of the member.
R -:The distance measured from the center of curvature to the neutralaxis.
r -:The distance measured from the center of curvature to the centroidof the cross-sectional area.
r -:The distance measured from the center of curvature to the point where the stress σis to be determined.
92
M ( ro R )
o Normal stress at the bar's top.
Aro ( r R )
Example:-The curved bar has a cross-sectional area shown below .If it issubjected to bending moments of 4
kN • m, determine the maximum normal stress developed in the bar.
r
yA 757500 233.076 mm
A 3250
A
R
dA
A r
A 3250 mm
dA r br2 r
R
b ln 2 ln 2 b
r1 (r2 r1 ) r1
250 50 280 280
= 50 ln ln 50 14.04389 mm
200 (280 250) 250
3250
R 231.417 mm
14.04389
93
M ( R ri ) 4 10 3 (231.417 10 3 200 10 3 )
B 116.5373 MPa
Ari (r R ) 3250 10 6 200 10 3 (233.076 10 3 231.417 10 3 )
M (ro R ) 4 10 3 (280 10 3 231.417 10 3 )
A 128.7231 MPa The
Aro (r R ) 3250 10 6 280 10 3 (233.076 10 3 231.417 10 3 )
maximum stress at point A= 128.7231 MPa
Example:-The frame of a punch press is shown below. Find the stresses at the inner and outer surface at
section x-x of the frame if W=5000 N.
W
x x 25 mm 50 mm
W
6 mm 18 mm 100 mm
40 mm
bi bo
A h
2 bi
bo
h
18 6
A( ) 40 480 mm 2
2
dA b r bo ri r 18 65 6 25 65
R
( i o
h
) ln o (bi bo ) (
ri 40
) ln (18 6) 12.365 mm
25
A 480
R 38.8175 mm
dA 12.365
A r 6 mm 18 mm
40 mm 25 mm
65 mm
94
Area(mm2) A(mm2) y-(mm) y-A(mm3)
rectangle 720 45 32400
Triangle -120 51.666 -6200
Triangle -120 51.666 -6200
480 20000
r
yA 20000 41.666 mm
A 480
M=W×d=5000×(100×10-3+41.666×10-3)=708.33 N.m
M ( R ri ) W 708.33(38.8175 10 3 25 10 3 ) 5000
i
Ari ( r R ) A 480 10 25 10 ( 41.666 10 38.8175 10 ) 480 10 6
6 3 3 3
296.747 MPa
M ( ro R ) W 708.33(65 10 3 38.8175 10 3 ) 5000
o
Aro ( r R ) A 480 10 65 10 ( 41.666 10 38.8175 10 ) 480 10 6
6 3 3 3
198.26 MPa
95
Slop and Deflection in Beams
The elastic curve :-the deflection diagram of the longitudinal axis that passes
through the centroid of each cross sectional area of the beam.
96
x-axis extends positive to the right.
v-axis extends positive upward from the x-axis.
1
y
E
My
I
1 M
EI
When M is positive, extends above the beam, i.e. in the positive v direction.
When M is negative, extends below the beam, or in the negative v direction.
Integration Method
The elastic curve for a beam can be expressed mathematically as v=f(x)
1 d 2 v / dx 2
[1 (dv / dx) 2 ]3 / 2
M d 2 v / dx 2
EI [1 (dv / dx) 2 ]3 / 2
The slop of the elastic curve which is determined from dv/dx will be very small, and
its square will be negligible compared with unity.
1 d 2v
dx 2
M d 2v
EI dx 2
97
dM
V
dx
d d 2v
V ( x) ( EI 2 )
dx dx
dV
w
dx
d2 d 2v
w( x) 2 ( EI 2 )
dx dx
EI always positive quantity
d 2v
M EI ( 2 )
dx
d 3v
V EI ( 3 )
dx
d 4v
w EI ( 4 )
dx
dv
dx
98
Boundary conditions
dv
dx
EI Mdx C1
Example: The cantilevered beam shown is subjected to a vertical load P at its end.
Determine the equation of elastic curve. EI is constant.
M 0
M+Px=0
M=-Px
d 2v
M EI ( ) =-Px
dx 2
dv 1
EI Px 2 C1 ……………………..(1)
dx 2
1
EIv Px 3 C1 x C 2 ………………………(2)
6
Boundary conditions
99
at x=L
dv
=0 and v =0
dx
1 1 2
0 PL2 C1 C1 PL
2 2
1 1 1 3 1 3 PL3
0 PL3 PL3 C 2 C2 PL PL =
6 2 6 2 3
1 1 P
EI Px 2 PL2 ( L2 x 2 )
2 2 2 EI
1 PL2 PL3
EIv Px 3 x
6 2 3
P
v ( x 3 3L2 x 2 L3 )
6 EI
Example: The simply supported beam shown supports the triangular distributed loading.
Determine the maximum deflection. EI is constant.
L
Due to symmetry we take 0≤ x ≤
2
M 0
w L w x3 L x3
M x 0 M w ( x )
4 3L 4 3L
2 3
d v L x
M EI ( 2 ) = w ( x )
dx 4 3L
4
dv w L w x
EI x 2 C1 ………………….(1)
dx 8 12 L
w L 3 w x 5
EIv x C1 x C 2 ……..………..(2)
24 60 L
100
Boundary conditions
L dv
at x= =0
2 dx
w L 2 w x 4 5w L3
0 x C1 C1
8 12 L 192
at x=0 v=0
0=0-0+0+C2 C2=0
w L 3 x 5 5 L3
v ( x x)
EI 24 60 L 192
L
Vmax at x=
2
w L4 L4 5 L4 w L4
v max ( ) =
EI 192 1920 384 120 EI
Discontinuity Method
101
0 for x a
xa
n
( x a) for x a
n
n 1
xa
x a dx C
n
n 1
3 1
M=2.75<x-0>1+1.5<x-3>0- <x-3>2- <x-3>3
2 6
3 1
=2.75x+1.5<x-3>0- <x-3>2- <x-3>3
2 6
Example:- Determine the equation of the elastic curve for the beam shown below. EI is
constant.
F y 0
Ay-40-12=0 Ay=52 kN
M A 0
MA-40×2.5-50-12×9=0 MA=258 kN.m
102
8 8
M=-258<x-0>0+52<x-0>1- <x-0>2+50<x-5>0+ <x-5>2
2 2
d 2v
EI 2
=-258+52x-4x2+50<x-5>0+4<x-5>2
dx
dv 4 4
EI =-258x+26x2- x3+50<x-5>1+ <x-5>3+C1………….….(1)
dx 3 3
26 1 1
EIv=-129x2+ x3- x4+25<x-5>2+ <x-5>4+C1x+C2………….(2)
3 3 3
B.C
dv
=0 at x=0 in eq.(1)
dx
v=0 at x=0 in eq.(2)
C1=0
C2=0
1 26 1 1
v= (-129x2+ x3- x4+25<x-5>2+ <x-5>4)
EI 3 3 3
B
M
B/ A dx
A
EI
The notation B / A is referred to as the angle of the tangent at B measured with respect to
the tangent at A.
103
Theorem 1 The angle between the tangents at any two points on the elastic curve equals
the area under the M/EI diagram between these two points.
If the area under M/EI diagram is positive, the angle is measured counterclockwise
from the tangent A to tangent B.
If the area under M/EI diagram is negative, the angle B / A is measured clockwise from
tangent A to tangent B. B / A will measured in radians.
B
M
tA/ B x dx
A
EI
t A / B : the vertical deviation of the tangent at A with respect to the tangent at B.
xdA x dA
B
M
EI dx
A
represents the area under the M/EI diagram, we can also write:-
B
M
tA/ B x dx
A
EI
x is the distance from A to the centroid of the area under the M/EI diagram between A
and B.
104
Theorem 2 The vertical deviation of the tangent at a point A on the elastic curve with
respect to the tangent extended from another point B equals the moment of the area under
the M/EI diagram between these two points. This moment is computed about point A
where the vertical deviation t A / B is to be determined.
Example: Determine the slope of the beam shown at points B and C. EI is constant
B = B / A
C =C / A P
MA
M A 0
Ay
MA-PL=0
MA=PL
F y 0
Ay=P
B
M
B/ A dx Area under the M/EI diagram from A to B
A
EI
105
PL L 1 PL PL L
B = B / A
2 EI 2 2 EI 2 EI 2
3PL2
= rad clockwise
8 EI
PL 1 PL
2
C =C / A =
L = rad clockwise
EI 2 2 EI
Mo Mo
vB= t B / A
vC= t C / A
F y 0
Ay=0
M A 0
M-Mo=0
M=Mo
B
M
vB= t B / A x dx
A
EI
1 L M o L M o L2
= =
2 2 EI 2 8EI
L M o M o L2
A
M
vC= t C / A x dx = L =
C
EI 2 EI 2 EI
106
Example: Determine the slope at point C for the steel beam shown. Take Est=200 GPa,
I=17×106 mm4 L
C
C = A C / A
tB / A
Since the angle is very small A =tan A =
L
1 24 1 2 24 1
t B / A = 2 (6) (6) (2) (2)
3 EI 2 3 EI 2
320
tB / A =
EI
8 1 8
C / A = ( 2)
EI 2 EI
320 8 32
C = - =
8 EI EI EI
32
C = =0.009411 rad
200 10 17 10 6
9
M dx
L
M( )
0
P EI
Where:-
=displacement of the point caused by the real loads acting on the beam.
P=external force of variable magnitude applied to the beam in the direction of .
M=internal moment in the beam, expressed as a function of x and caused by both the force
P and the load on the beam.
M dx
L
M( )
0
M EI
=the slope of the tangent at a point on the elastic curve.
107
M =an external couple moment acting at the point.
M 0
x
M wx ( ) Px 0
2
x2
M w Px
2
M
x
P
When P=0
x 2 M
M w , x
2 P
wx 2
( x)
M dx
L L L
w
B M ( ) 2 dx x 3 dx
0
P EI 0 EI 2 EI 0
L
w 4 wL4
B x =
8EI 0 8EI
Example: Determine the displacement of point A of the steel beam shown below.
I=450 in4, Est=29×103 ksi.
P
Cx
By Cy
M B 0
10
Cy×20-60×10+15× +P×10=0
3
Cy =27.5-0.5P
F y 0
By+27.5-0.5P-60-15-P=0
108
3 2
x1
P 20
By=47.5+1.5P
F x 0
Cx=0 M1
V1
M 0 x1
3 x
M1+ x12 ( 1 ) +Px1=0
20 3
3
x
M1=- 1 - Px1
20
P 3x 2
M 1 15 kip
=-x1
P
When P=0
x13 V2 M 2
M1=-
20 x2
M 1
=-x1
P 47.5 1.5 P
M 0
x2 10
M2+3x2( )+15×( +x2)+P(10+x2)-( 47.5+1.5P)x2=0
2 3
3
M2= x 22 +(32.5+0.5P)x2-10P-50
2
M 2
=0.5x2-10
P
When P=0
3 M 2
M2= x 22 +32.5x2-50 , =0.5x2-10
2 P
L
M 1 dx1 L M 2 dx 2
A M1( ) M2( )
0
P EI 0 P EI
10 20
(12) 3 x13 (12) 3 3
A
EI 0 20
( x1 ) dx1
EI 0 2
( x 22 32.5 x 2 50)(0.5 x 2 10)dx 2
(12) 3 x 5 10 3 20
A
1
x 24 10.4166 x 23 175 x 22 500 x 2
EI 100 0 16 0
(12) 3
A (1000 6667.2)
EI
A 0.75 in
109
Example: Determine the slope at point B of the A-36 steel beam shown below.I=70×106
mm4 and E=200 GPa.
2 KN / m
C
A B
10 m 5m
10 KN
C
M
Ay By
M A 0
M1
By×10+ M -10×12.5=0 V1
M x1
By=12.5-
10
F y 0
M
M 2 .5
Ay+12.5- -10=0 10 2x 2
10
M M
Ay= -2.5
10 V2 M 2
M 0 x2
M
M1-( -2.5)x1=0 M
10 12.5
M M 10
M1= ( -2.5)x1 2 .5
10 10
M 1 1
x1
M 10
When M =0
M 1 1
M1= -2.5x1 , x1
M 10
M 0
x2 M M
M2+2x2( )-(12.5- )x2-( -2.5)(10+x2)+ M =0
2 10 10
110
M M
M2=(12.5- )x2+( -2.5)(10+x2)- x 22 - M
10 10
M 2 1 1
= x1 +1+ x1 -1=0
M 10 10
When M =0
M 2
M2=- x 22 +10x2-25 , =0
M
L
M dx
10
M dx 5 M dx
B M ( ) = M1( 1 ) 1 M 2 ( 2 ) 2
0
M EI 0 M EI 0 M EI
x
(2.5 x1 )( 1 )dx1
10
= 10 0
0
EI
10
1
0.25x
2
= 12
dx1
70 10 10 200 10
6 6 1
0
-3 3 10
=0.07142×10 (-0.0833 x 1 0 )
B 0.00595 rad
=-0.3410
1. Method of Integration:
Example: The beam is subjected to the distributed loading shown. Determine the reaction
at A. EI is constant.
111
M 0
wo x 3
M Ay x 0
6L
w x3
M Ay x o
6L
2
d v
M EI ( 2 )
dx
wo x 3 d 2v
Ay x EI ( 2 )
6L dx
2
dv Ay x w x4
EI ( ) o C1
dx 2 24 L
3 5
Ay x w x
EIv o C1 x C 2
6 120 L
Boundary Conditions
dv
at x=0 v=0 , at x=L 0 , at x=L v=0
dx
0=0-0+0+C2 C2=0
2 3
Ay L wo L
C1 0 …………………(1)
2 24
Ay L3 wo L4
C1 L 0 ………………..(2)
6 120
From equations (1) and (2)
3
wo L
C1=
24
w L
Ay o
10
Example: The beam shown below is fixed supported at both ends and is subjected to the
uniform loading shown. Determine the reactions at the supports. Neglect the effect of axial
load.
M
112
F y 0
wL
VA=VB=
2
MA=MB= M
M 0
wx 2 wL
M M x0
2 2
wx 2 wL
M xM
2 2
d 2v
M EI ( 2 )
dx
2
d v wx 2 wL
EI ( 2 ) xM
dx 2 2
dv wx 3 wL 2
EI ( ) x M x C1
dx 6 4
wx 4 wL 3 M 2
EIv x x C1 x C 2
24 12 2
Boundary Conditions
dv
at x=0 v=0 , at x=0 0 , at x=L v=0
dx
0=-0+0-0+0+C2 C2=0
0=-0+0-0+C1 C1=0
wL4 wL4 M 2
0= L
24 12 2
wL2
M
12
113
Moment Area Method(Statically Indeterminate):
Since application of the moment area theorems requires calculation of both the area
under the M/EI diagram and the centroidal location of this area, it is often convenient to
use separate M/EI diagrams for each of the known loads and redundant rather than using
the resultant diagram to compute these geometric quantities.
114
Example: The beam is subjected to the concentrated loading shown. Determine the
reactions of the supports. EI is constant.
Using superposition method to draw the separate M/EI diagrams for the redundant reaction
By and the load P.
A B
A B
1 By L 2 PL L 1 PL 2
( )( L)( L) ( )( L)( ) ( )( L)( L) 0
2 EI 3 EI 2 2 EI 3
B y 2 .5 P
F y 0
-Ay-P+2.5P=0 Ay=1.5P
M A 0
MA=0.5PL
115
Example: The beam is subjected to the couple moment at it end C as shown below.
Determine the reaction at B. EI is constant.
tC / A t B / A
From the elastic curve t C / A 2t B / A
2L L
Using superposition method to draw the separate M/EI diagrams for the redundant reaction
By and the load Mo.
M
EI
L 2L
3 2 2 EI 3 2 2 EI 3 2 EI 12 EI L
3 3
L M L M 3 Mo
(6 B y 8 o ) =2 ( By o ) By
12 EI L 12 EI L 2 L
M 5M o
Ay o , C y
4L L
116
Combined Stresses
There are three types of loading: axial, torsional and flexural.
P
Axial loading a
A
T.r
Torsional loading
J
M .y
Flexural loading f
I
There are four possible combinations of these loadings:
1. Axial and flexural.
2. Axial and torsional.
3. Torsional and flexural.
Q
4. Axial , torsional and flexural.
B
f y
y
A
A
M .y
f
I
P BB P
a yy
yy
A
A
P Q
a
A
P BB P
a yy
yy
A
A f
117
Example: The bent steel bar shown is 200 mm square. Determine the normal stresses at A
and B.
500 kN
200 mm 4
3
A
B
4
3
M C 0
250 mm 450 mm 100 mm
-500×200×10-3+R1×900×10-3=0
R1=111.111 kN
F y 0
R2+111.111cos(53.1301)-500sin(53.1301)=0
R2=333.333kN 500 kN
4
3 53.1301
750 mm
A
R1
C B
4
3
R3
150 mm
Fx 0 R2
R3+111.111sin(53.1301)-500cos(53.1301)=0
R3=388.888kN
P 500
A 12.5 MPa
A (200 200 10 6 )
M=-500×200×10-3+111.111×700×10-3
M=-22.2223 kN.m
M .y 22.2223 100 10 3
f 16.666 MPa
I (200 10 3 ) (200 10 3 ) 3 / 12
A a f 12.5 16.666 29.166 MPa
B a f 12.5 16.666 4.166 MPa
118
Stresses at a Point
x y x y
x ( )( ) cos 2 xy sin 2 ……………………..(1)
2 2
x y x y
y ( )( ) cos 2 xy sin 2 …………………….(2)
2 2
x y
x y ( ) sin 2 xy cos 2 …………………….(3)
2
The planes defining maximum or minimum normal stresses are found from:
2 xy
tan 2 p ………………(4)
x y
The planes of maximum shearing stresses are defined by :
x y
tan 2 s ………………(5)
2 xy
The planes of zero shearing stresses may be determined by setting τ equal to zero.
2 xy
tan 2 ……………….(6)
x y
Equation 6 and 4 show that maximum and minimum normal stresses occur on planes of
zero shearing stresses.
The maximum and minimum normal stresses are called the principal stresses.
119
Equation 5 is the negative reciprocal of equation 4. This means that the values of 2θ s from
equation 5 and equation 4 differ by 90ο. This means that the planes of maximum shearing
stress are at 45o with the planes of principal stress.
x y x y
max . ( ) ( ) 2 xy
2
…………………(7)
min . 2 2
x y
max ( ) 2 xy
2
…………………..(8)
2
x y
avg ………………….(9)
2
Example:The state of plane stress at a point is represented by the element shown.
Determine the state of stress at the point on another element oriented 30o clockwise from
the position shown.
25 .849 MPa
x
68 .791 MPa
120
Example: When the torsional loading T is applied to the bar shown it produce a state of
pure shear stress in the material. Determine a) the maximum in plane shear stress and the
associated average normal stress. b) the principal stresses.
x 0
y 0
xy 60 MPa
x y
a) max ( ) 2 xy
2
60 MPa
2
00 2
max ( ) ( 60) 2 60 MPa
2
x y 0 0
avg 0
2 2
x y
tan 2 s
2 xy
0
tan 2 s 0
2 60
θs=0
x y x y
b) max . ( ) ( ) 2 xy
2
min . 2 2
00 00 2
max . ( ) ( ) (60) 2 60 MPa
min . 2 2
σmax=60 MPa
σmin=-60 MPa
2 xy
tan 2 p
x y
2 60
tan 2 p
0
o
2 p p 45 or 135
2 4
x y x y
x ( )( ) cos 2 xy sin 2 60 MPa
2 2
0 0
x ( ) ( ) cos(90) 60 sin(90) 60 MPa
2 2
60 MPa
121
Example: The state of plane stress at a point on a body is shown on the element. Represent
this stress state in terms of the principal stresses.
x 20 MPa
y 90 MPa
60 xMPa
y x y 2
maxxy. ( ) ( ) xy
2
min . 2 2
20 90 20 90 2
max . ( ) ( ) (60) 2
min . 2 2
max . 35 81.394
min .
σmax=116.394 MPa
σmin=-46.394 MPa
2 xy 2 60
tan 2 p = 1.090909
x y 20 90
o
2 p 47.489
p 23.744 or 66.256
x y x y
x ( )( ) cos 2 xy sin 2
2 2
20 90 20 90
x ( )( ) cos( 47.489) 60 sin( 47.489) 46.349 MPa
2 2
θp1=66.256o
θp2=-23.744o
122
Example: A sign of dimensions 2 m×1.2 m is supported by a hollow circular pole having
outer diameter 220 mm and inner diameter 180 mm as shown below. The sign is offset 0.5
m from the center line of the pole and its lower edge is 6 m above the ground. Determine
the principal stresses and maximum shear stresses at points A and B at the base of the pole
due to wind pressure of 20 kPa against the sign.
w=PA=2×(2×1.2)=4.8 kN
T=wr=4.8×(1+0.5)=7.2 kN.m
M=wd=4.8×(6+0.6)=31.68 kN.m
V=w=4.8 kN
I [d 24 d 14 ] [(220 10 3 ) 4 (180 10 3 ) 4 ]
64 64
I=63.46×10-6 m4
220 10 3
31.68
M .y 2
A 54.91 MPa
I 36.46 10 6
220 10 3
7 .2
T .r 2
1 6.24 MPa
J 3 4 3 4
[(220 10 ) (180 10 ) ]
32
VQ
2 , t 2( r2 r1 ) , I ( r24 r14 ) , A ( r22 r12 )
It 4 2
4r 4r
( 2 )( r22 ) ( 1 )( r12 )
y1 A1 y 2 A2 4 r23 r13
y 3 2 3 2 [ ]
A1 A2 2 2 3 r22 r12
r2 r1
2 2
4 r23 r13 2 2
Q yA [ 2 ] (r2 r12 ) (r23 r13 )
3 r2 r1 2
2 3
2
V (r23 r13 )
3 4V (r22 r2 r1 r12 )
2
4 3 (r22 r12 )(r22 r12 )
(r2 r1 ) 2(r2 r1 )
4
4
τ2=0.76 MPa
54.91 MPa
123
Mohr's Circle
For plane stresses transformation have a graphical solution that is often convenient to use
and easy to remember. Furthermore this approach will allow us to visualize how the
normal and shear stress components x and x y vary as the plane on which they act is
oriented in different directions. This graphical solution known as Mohr's circle.
x y x y
x ( )( ) cos 2 xy sin 2
2 2
x y
x y ( ) sin 2 xy cos 2
2
The parameter θ can be eliminated by squaring each equation and adding the equations
together. The result is:
x y x y
[ x ( )]2 x y ( ) 2 xy
2 2
2 2
x y x y
Let c , R2= ( ) 2 xy
2
2 2
[ x c] x y R 2
2 2
this equation represents a circle having a radius R and center at point
(c,0).
124
x y
Plot the center of the circle C which is located on the σ axis at a distance avg
2
from the origin.
3. Plot the reference point A having coordinate A( x , xy ). This point represents the
normal and shear stress components on the element's right hand vertical face, and
since the x axis coincides with the x axis, this represents θ=0.
4. Connect point A with the center C of the circle and determine CA by trigonometry.
This distance represents the radius R of the circle.
5. Once R has been determined , sketch the circle.
Principal Stresses
The principal stresses σ1 and σ2 (σ1≥σ2) are represented by the two points B and D where
the circle intersects the σ axis i.e where τ=0.
These stresses act on planes defined by angles θp1 and θp2. They are represented on the
circle by angles 2θp1 and 2θp2and are measured from the radial reference line CA to line CB
and CD respectively.
Using trigonometry only one of these angles needs to be calculated from the circle since θp1
and θp2 are 90o apart.
125
Maximum in Plane Shear Stress.
The average normal stress and maximum in plane shear stress components are determined
from the circle as the coordinates of either point E or F. In this case the angles θs1 and θs2
give the orientation of the planes that contain these components. The angle 2θ s1 can be
determined using trigonometry.
2
12 0 2
R ( ) (6) 2 =8.485 ksi
2
1 c R
1 -6+8.485=2.485 ksi
2 c R
2 -6-8.485=-14.485 ksi
6 o
2 p 2 tan 1 ( ) tan 1 (1) 45
12 6
o
p 2 22.5
126
Example: An element in plane stress at the surface of a large machine is subjected to
stresses shown below. Using Mohr's circle determine the following quantities a) the stress
acting on element inclined at an angle 40o b)the principal stresses and c) the maximum
shear stress.
x 15ksi
5 ksi
y 5 ksi
xy 4ksi 4 ksi
15 ksi
x y 15 5
c 10 ksi
2 2
x y
R ( ) 2 xy
2
2 F
15 5 2 P
R ( ) (4) 2 =6.403 ksi
2 R 6.403 ksi
A(15,4) D 41.34 B
C
2 p1 38.66
4 ksi
1 4 o 10 ksi
2 p1 sin ( ) 38.66
6.403
p1 19.33
P A
1 c R
1 10+6.403=16.403 ksi 15 ksi
2 c R 3.597 ksi
2 10-8.485=3.597ksi p 2 109.33
16.403 ksi
x 10 6.403 cos(41.34) 14.807 ksi p1 19.33
40
127
max R 6.403 ksi
avg 10 ksi
avg c 10 ksi
o
2 s1 38.66+90=128.66
o
s1 64.33 counterclockwise
s1 64.33
1 , 2
from Mohr’s circle or from stress transformation equations.
Example: An axial force of 900 N and a torque of 2.5 N.m are applied to the shaft as
shown. If the shaft has a diameter of 40 mm, determine the principal stresses at appoint P
on its surface.
T r 2.5 (20 10 3 )
= =198.94367 kPa
J 3 4
(20 10 )
2
P 900
= =716.19724 kPa
A (20 10 3 ) 2
128
x y 716.19724
c 358.09862 kPa
2 2
x y 0 716.19724 2
R ( ) 2 xy ( ) (198.94367) 2 409.65 kPa
2
2 2
Example: The beam shown below is subjected to the distributed loading of w=120 kN/m.
Determine the principal stresses in the beam at point P, which lies at the top of the web.
Neglect the size of the fillets and stress concentrations at this point. I=67.4×10-6 m4.
Ax=0
∑MB=0
Ay×2-240×1=0 Ay=120 kN
By=120 kN
-V-36+120=0
V=84 kN
129
M-120×0.3+36×0.15=0
M=30.6 kN.m
My 30.6 10 3 100 10 3 175 mm
45.4 MPa
I 67.4 10 6
15 mm
y P
VQ
N. A
It
Q y A =(107.5×10 )×(175×10 ×15×10 )=0.000282187 m
-3 -3 -3 3
84 0.000282187
35.168 MPa
67.4 10 6 10 10 3
2 2
Strain at a Point
130
Plane Strain
x y x y xy
x cos 2 sin 2
2 2 2
x y x y xy
y cos 2 sin 2
2 2 2
xy x y xy
( ) sin 2 cos 2
2 2 2
xy
tan 2 p
x y
x y x y xy
1, 2 ( )2 ( )2 Principal strain
2 2 2
x y
tan 2 s ( )
xy
max x y 2 xy
( ) ( )2 Maximum in plane shear strain
2 2 2
x y
avg
2
30o
x y x y xy
x cos 2 sin 2
2 2 2
131
500 10 6 300 10 6 500 10 6 300 10 6 200 10 6
x cos(60) sin(60)
2 2 2
x 213 10 6
x y x y xy
y cos 2 sin 2
2 2 2
500 10 6 300 10 6 500 10 6 300 10 6 200 10 6
y cos(60) sin(60)
2 2 2
y 13.4 10 6
xy x y xy
( ) sin 2
cos 2
2 2 2
xy 500 10 6 300 10 6 200 10 6
( ) sin( 60) cos(60)
2 2 2
x y 793 106
Mohr's Circle – Plane Strain
x y
C=
2
x y xy
R= ( )2 ( )2
2 2
xy
Point A ( x , )
2
The principal strain 1 and 2 are determined from the circle as the coordinates of
points B and D.
The average normal strain and the maximum in plane shear strain are determined
from the circle as the coordinates of points E and F.
132
The normal and shear strain components x and x y for a plane specified at angle
can be obtained from the circle using trigonometry to determine the coordinates of
point P.
50
sin 1 ( ) 26.56
111.8
40 26.56 13.44
x (C R cos )
x (200 10 6 111.8 10 6 cos(13.44))
x (309 10 6 )
xy
R sin
2
xy
111.8 10 6 sin(13.44)
2
x y 52 10 6
y (C R cos )
y (200 10 6 111.8 10 6 cos(13.44))
y (91.3 10 6 )
133
Theories of Failure:-
1. Ductile Materials
a) Maximum Shear Stress Theory
1 Y
1 , 2 have same signs. (Rankine)
2 Y
2. Brittle Materials
a) Maximum Normal Stress Theory
If the material is subjected to plane stress.
1 ult
2 ult
134
Example:- The steel pipe shown below has an inner diameter of 60 mm and an outer
diameter of 80 mm. If it is subjected to a torsional moment of 8 KN.m and a bending
moment of 3.5 KN.m, determine if these loadings cause failure as defined by the
maximum distortion energy theory. The yield stress for the steel found from a tension test
is σY=250 MPa.
12 1 2 22 ? Y2
Point A
Tr 8 40 10 3
A 116.41 MPa
J 3 4 3 4
[(40 10 ) (30 10 ) ]
2
My 3.5 40 10 3
A 101.859 MPa
I 3 4 3 4
[(40 10 ) (30 10 ) ]
4
116 .41 MPa
x y 101.859 0
c= = 50.9295 MPa
2 2
x y 101.859 0 2
R= ( ) 2 xy2 ( ) (116.41) 2 =127.063 MPa
2 2
A(-101.859,116.41) Draw Mohr’s circle
1 C R =-50.9295+127.063=76.1335 MPa
2
2 C R =-50.9295-127.063
=-177.9925 MPa C
12 1 2 22 Y2
A 1
135
Example:- The solid shaft shown below has a radius of 0.5 in. and is made of steel having
yield stress Y 36 ksi. Determine if the loadings cause the shaft to fail according to the
maximum shear stress theory and the maximum distortion energy theory.
P 15
19.1 ksi
A (0.5) 2
Tr 3.25 0.5
A 16.55 ksi
J 4
(0.5)
2
x y x y
1, 2 ± ( ) 2 xy2
2 2
19.1 0 19.1 0 2
= ± ( ) (16.55) 2
2 2
=-9.55±19.11
1 9.56 ksi
2 28.66 ksi
1 2 Y
9.56 28.66 36
38.2>36
So the failure will occur according to this theory.
maximum distortion energy theory
12 1 2 22 Y2
(9.56)2-(9.56)(-28.66)+(-28.66)2=(36)2
1186.515<1296
136
Example:- The solid cast iron shaft shown below is subjected to a torque of T=400 lb.ft.
Determine the smallest radius so that it does not fail according to the maximum normal
stress theory ult =20 ksi.
Tr 400 12 r 3055.8
J 4 r3
(r )
2
3055.8
x 0 , y 0, psi
r3
x y x y
1, 2 ± ( ) 2 xy2
2 2
00 0 0 2 3055.8 2
1, 2 ± ( ) ( 3 )
2 2 r
3055.8 3055.8
1 , 2
r3 r3
1 ult
3055 .8
=20000
r3
r=0.535 in.
137
Columns
Columns are long slender members subjected to an axial compressive force. The force
may be large enough to cause the member to deflect laterally or sides way, this deflection
is called buckling.
Critical Load
The maximum axial load that a column support when it is on the verge of buckling is
called the critical load (Pcr).
Any additional loading will cause the column to buckle and therefore deflect laterally.
138
In order to determine the critical load and the buckled shape of the column we will apply
the following equation:
d 2v
EI 2 M
dx
M section 0
M+Pv=0
M=-Pv
d 2v
EI Pv
dx 2
d 2v P
2
( )v 0 .......................(1)
dx EI
The general solution of equation (1) is:
P P
v C1 sin( x) C 2 cos( x) ......................(2)
EI EI
C1 and C2 are determined from the boundary conditions :
v=0 at x=0 C2=0
P
v=0 at x=L C1 sin( L) 0
EI
C1≠0 therefore
P
sin( L) 0
EI
P
L n
EI
n 2 2 EI
P n 1,2,3,.............
L2
The smallest value of P is obtained when n=1, so the critical load for the column is:
139
2 EI
Pcr
L2
This load is sometimes referred to as the Euler load, n represents the number of waves in
the deflected shape of the column; if n=2 two waves will appear in the buckled shape and
the column will support a critical load that is 4Pcr.
As a result engineers usually try to achieve a balance keeping the moments of inertia the
same in all directions
Ix Iy
2 EI
Pcr
L2
140
Pcr: critical or maximum axial load on the column just before it begins to buckle. This load
must not cause the stress in the column to exceed the proportional limit.
E: modulus of elasticity for the material.
I: least moment of inertia for the column's cross sectional area.
L: unsupported length of the column, whose ends are pinned.
I=Ar2
2E
cr
L
( )2
r
cr :critical stress which is an average stress in the column just before the column buckles.
This stress is an elastic stress and therefore:
cr Y
I
r: smallest radius of gyration of the column r .
A
L/r: slenderness ratio, it’s a measure of the column flexibility.
Example: A 24 ft long A-36 steel tube having the cross section shown below is to be used
as a pin ended column. Determine the maximum allowable axial load the column can
support so that it does not buckle. Est=29×103ksi, Y =36 ksi.
4
2 29 10 3 (3 2.75 4 )
EI
2
4
Pcr
L2 ( 24 12) 2
=64.52 kip.
Pcr 64.52
cr
A (3 2.75 2 )
2
=14.28 ksi
Since cr Y
Pallow=64.52 kip.
Example: The A-36 steel W8×31 member shown below is to be used as a pin connected
column. Determine the largest axial load it can support before it either begins to buckle or
the steel yields. Est=29×103ksi, Y =36 ksi. A=9.13 in2, Ix=110 in4, Iy=37.1 in4.
Buckling occurs about y-axis.
2 EI 2 29 10 3 37.1
Pcr
L2 (12 12) 2
=512 in4
Pcr 512
cr 56 ksi
A 9.13
cr Y
141
P P
y 36
A 9.13
P=328.68 kip.
Columns Having Various Types of Supports
Fixed-Free column
M section 0
M-P( -v)=0
M=P( -v)
d 2v
EI 2 P( - v)
dx
2
d v P P
2
v .......................(1)
dx EI EI
The solution of equation (1) consists of both a complementary and particular solution.
P P
v C1 sin( x) C2 cos( x) ......................(2)
EI EI
C1 and C2 are determined from the boundary conditions :
v=0 at x=0 C2=-
dv
=0 at x=0
dx
dv P P P P
C1 cos( x) C 2 sin( x)
dx EI EI EI EI
C1=0
P
v [1 cos( x)] .................(3)
EI
Since the deflection at the top of the column is , that is at x=L v=
P
cos( L) 0
EI
≠0
P P n
cos( L) 0 or L
EI EI 2
n 2 2 EI
P
4L2
The smallest value of P is obtained when n=1, so the critical load for the column is:
2 EI
Pcr
4L2
142
Effective Length
The effective length (Le) is the distance between points of inflection (that is , points of zero
moment ) in its deflection curve, assuming that the curve is extended (if necessary) until
points of inflection are reached.
Le=KL
Pinned –Ends K=1
Fixed-Free Ends K=2
Fixed-Ends K=0.5
Pinned-Fixed Ends K=0.7
Euler's formula becomes:
2 EI 2E
Pcr ; cr
(KL) 2 KL
( )2
r
KL/r: columns effective slenderness ratio.
For fixed-Free ends K=2
2 EI
Pcr
4L2
Example: A W6×15 steel column is 24 ft long and is fixed at is ends as shown below. Its
load carrying capacity is increased by bracing it about the y-y (weak) axis using strut that
are assumed to be pin connected to its midheight. Determine the load it can support so that
the column does not buckle nor the material exceed the yield stress. Take Est=29×103ksi
and Y =60 ksi. A=4.43 in2, Ix=29.1 in4, Iy=9.32 in4.
2 EI x 2 29 10 3 29.1
( Pcr ) x 401.7 kip
( KL) 2x (12 12) 2
2 EI y 2 29 10 3 9.32
( Pcr ) y 262.5 kip
( KL) 2y (0.7 12 12) 2
( Pcr ) y 262.5
cr 59.3 ksi
A 4.43
cr Y
Pcr=262.5 kip.
143
Example: A viewing platform in a wild animal park is supported by a raw of aluminum
pipe columns having length 3.25 m and outer diameter 100 mm. The bases of the columns
are set in concrete footings and the tops of the columns are supported laterally by the
platform (pinned). The columns are being designed to support compressive loads 100 kN.
Determine the minimum required thickness t of the columns if a factor of safety n=3 is
required with respect to Euler buckling for aluminum use 72 GPa for the modulus of
elasticity and use 480 MPa for the proportional limit.
144