100%(1)100% menganggap dokumen ini bermanfaat (1 suara)
4K tayangan1 halaman
This document specifies dimensional tolerances and mechanical properties for three grades (43A, 43B, 43C) of thick plate steel according to British Standard BS 4360. Key details include:
1. Plate thicknesses range from 6-80mm. Tolerances are specified in BS 4360 for plates over 12.5mm and BS 1449 P1 for thinner plates.
2. Chemical composition limits are provided for carbon, manganese, phosphorus, sulfur, silicon, and optional copper. Deoxidation uses silicon and aluminum.
3. Minimum yield strengths and tensile strengths vary based on plate thickness. Elongation and impact resistance minimums also differ based on plate thickness and test
This document specifies dimensional tolerances and mechanical properties for three grades (43A, 43B, 43C) of thick plate steel according to British Standard BS 4360. Key details include:
1. Plate thicknesses range from 6-80mm. Tolerances are specified in BS 4360 for plates over 12.5mm and BS 1449 P1 for thinner plates.
2. Chemical composition limits are provided for carbon, manganese, phosphorus, sulfur, silicon, and optional copper. Deoxidation uses silicon and aluminum.
3. Minimum yield strengths and tensile strengths vary based on plate thickness. Elongation and impact resistance minimums also differ based on plate thickness and test
This document specifies dimensional tolerances and mechanical properties for three grades (43A, 43B, 43C) of thick plate steel according to British Standard BS 4360. Key details include:
1. Plate thicknesses range from 6-80mm. Tolerances are specified in BS 4360 for plates over 12.5mm and BS 1449 P1 for thinner plates.
2. Chemical composition limits are provided for carbon, manganese, phosphorus, sulfur, silicon, and optional copper. Deoxidation uses silicon and aluminum.
3. Minimum yield strengths and tensile strengths vary based on plate thickness. Elongation and impact resistance minimums also differ based on plate thickness and test
Plates 6.00 ≤ e ≤ 80.00 mm (1) BS 4360 Hot-Rolled Products e ≤ 12.50 mm BS 1449 P1 Application Structural Material Chemical Composition % Grades 43 A 43 B 43 C C maximum 0.25 0.21 0.18 Mn maximum 1.60 1.50 1.50 P maximum 0.050 0.050 0.040 S maximum 0.050 0.050 0.040 Si maximum 0.50 0.50 0.50 Cu when specified 0.20/0.35 or 0.20/0.35 or 0.35/0.50 - 0.35/0.50 Deoxidation Si and Al Killed Si and Al Killed Si and Al Killed Mechanical Properties Minimum Yield Point e ≤ 16.00 mm 275 275 275 (TT) 16.00 < e ≤ 40.00 265 265 265 mm MPa 40.00 < e ≤ 63.00 255 255 255 mm 63.00 < e ≤ 100.00 245 245 245 mm Tensile Strength MPa 430/580 430/580 430/580 Lo = e ≤ 9.00 mm 16 16 16 Minimum 200 mm 9.00< e ≤ 150.00 20 20 20 mm Elongation % Lo = e ≤ 9.00 mm 17 17 17 80 mm 9.00< e ≤ 150.00 23 23 23 mm Lo =5.654 So 22 22 22 Impact Resistance Temperature °C - - zero Notch (V) J Longitudinal 6.00 e ≤ - - 27 minimum 100.00mm Supply As Rolled As Rolled As Rolled