AM3440-A/B/C
AM3440-D
O9550-A/D
V4150
E1510-S
E1500-2S
T2500-2S
iNET EMS
iNMS NMS
Loop Telecom has developed and produced since 1981 CSU/DSU, then TDM multiplexers and has built a complete
range of E1/T1, E3/T3 Digital Access Cross Connect (DACS) to support multi-services applications.
These solutions are tracking single DS0 to high density interfaces, they support uplinks TDM/PDH or SDH/SONET
up to STM16/OC48, TDMoG PseudoWire encapsulation over IP/Gigabit Ethernet and recently PTN transport over
10 GE with MPLS-TP or Carrier Ethernet.
These high-quality devices with redundant functions provide high speed DS0 circuit protection. We support
many different interfaces for voice, analog, low and high rates synchronous/asynchronous with standard or spe-
cial protocols, Ethernet and dedicated interfaces for Power Companies, Oil & Gas, Air traffic Control, Railway,
Military…
We provide different NMS including a high-level iNMS for large infrastructures particularly in Telco and Utilities.
www.LoopTelecom.com
Multiservice Access Multiplexer - PDH/TDM DACS
Several thousands of the Loop Telecom has accumulated a large knowledge to convert and transport over
DACS AM3440 Series are TDM or IP networks the different types of links: analog signals, voices, synchronous,
installed over the world. It asynchronous or legacy interfaces, dedicate to the teleprotec on or radio, dry con-
supports almost all existing tacts… and Ethernet. We supply different mul plexers with cross-connect to groom
interfaces. It is a fully modu-
low rate n x 64K or sub-rate signal over TDM E1/T1 or SDH/SONET or Ethernet/IP
lar and redundant device
and exists in different sizes.
networks with a high respect of reliability, synchroniza on, latency of the customer
applica ons.
AM3440-D
2U PDH ADM mul plexer
same as AM3440A except
• Redundant CPU and PS
• 9 mini slots,
• DACS 36 x 31TS
• Circuit protec on: 1+1 and
ULSR E1
www.LoopTelecom.com
Page 2
Point to Point or Multipoint Voice, RTU … in Transports
Loop Telecom supplies TDM DS0 mul plexing solu ons to different railway companies around the world. In the single equipment per node
we support different applica ons requested on railways lines:
- the voice from central PBX with E1-CAS or FXO to FXS on sta ons,
- the service voice between two sta ons with FXS to FXS in PLAR mode,
- the conference from Central sta on to 16 sta ons with FXS, E&M and RS232 interfaces,
- the NTU to RTU communica on in Voice E&M, Magneto or RS232, RS485 as Point to Point or Mul point,
- the E1 trunking radio (PMR),
- and many Ethernet applica ons as IP-Video, cke ng ...
All nodes are secured by redundant CPUs, Power supplies, WAN links and if necessary all tributary interfaces with chassis.
www.LoopTelecom.com
Page 3
Multiservice Access Multiplexer PDH/TDM with SDH/SONET
These chassis are used in Loop Telecom produces a large range of SDH/SONET and Hybrid with mul service
concentra on nodes appli- DS0 DACS equipment. The O9550 is a very high density mul service PDH DACS with
ca ons with a large num- four SDH/SONET uplinks for u li es, transporta on or defense applica on.
ber of analog and industri-
The V4150 is a very high density system suppor ng in a single chassis 504 E1/T1
al interfaces. The mul ple
End-to-End circuits are set
interfaces, with E3/T3, STM1/OC3 and 504E1/672T1 DS0 non-blocking cross-
by iNMS. connect matrix for Telco voices/lease lines or large u li es concentra on sites.
High Density Multiservice DACS
connected to TDM E1/T1, SDH/SONET and Ethernet WANs
This mul plexer mul service based on E1/T1 DS0 cross-connec on can be integrated in TDM net-
work with E1 or T1 interfaces, in SDH/SONET through itds 2 x 2 STM1/4 interfaces on CPU cards and
in Ethernet/Gigabit Ethernet through its combo FE/GE interfaces with TDM PseudoWire Emula on
End to End (PW3E) to another PW3E device. All three WANs can be ac ve together.
The DACS and TDM network will run with the same clock, the SDH has its own clock and we will make
O9550-A care to the clock of the 2 PW3E mul plexers, the local can carry the clock to the remote device.
5U Modular PDH DACS and
ADM SDH/SONET mul plexer:
• Redundant CPU and PS
• 4 aggregate interfaces
STM1/4 OC3/12 with MSP
and SNCP protec on
• 12 slots and 4 mini slots of
4 E1/T1 backplane each
• Clock PDH and clock SDH
• DACS 504+64 E1 x 31TS
or 672+52 T1 x 24TS
O9550 Protection
• E1/T1 protec on: 1+1, ring
The chassis can be equipped fully redundant with dual CPU with cross-connect and dual power supply.
SNCP DS0 or ULSR E1
• E1, T1, copper or fiber SDH/SONET cards support MSP and SNCP protec on with one or two CPU. Each pair of E1/T1 from con-
• Voice E1-CAS, FXO/FXS/ guous cards can support 1+1 line and card protec on. The op onal circuit protec ons can be applied
E&M/Conference/Magneto at the n x TS level. The DS0 SNCP Automa c Protec on Switching is provided in ring by 3E1 cards and the
• Serial X21, V35, EIA530 ULSR E1 protec on can be applied on a FE1 ring. All PDH protec ons are describes in page 2.
• RS232, RS485, RS422, bridge The TDM PseudoWire over GE are protected with RSTP.
• C37.94, Teleprotec on
• Ethernet bridge and router WAN and Tributary interfaces
• TDMoEthernet/ TDMoverIP
All AM3440 cards are available for O9550-A/C, but their firmware is different. This DACS supports:
- WAN cards 1 or 4 E1 or T1, copper or fiber interfaces with mode G703, G704 and CAS with CAS fabric,
- Voices cards with E1-CAS, FXO, FXS, E&M, Magneto and Conference cards,
- Serial interfaces X21, V35, V36 and EIA530 with rate n.64kbps or sub-rate with V110,
- Serial Async/Sync RS232, RS485 and RS422 with sub-rate with X50 or V110, Terminal Server, Omnibus
- Analog Bridge and Digital Bridge to support mul point, G703 64k Codirec onal/Contra-Direc onal
- Interfaces for Power Industries C37.94 and Teleprotec on
O9550-C - Dry contact Input/Output to carry contact open/close or generate SNMP trap
3U Modular PDH DACS and
- Ethernet Router, Bridge and switch with 2/8 ports, 64 WAN EoPDH from 64kbps to 8Mbps
ADM SDH/SONET mul plexer:
- 2 GE Combo WAN, 2 GE LAN with TDMoE/TDMoverIP encapsula on of 4 E1/T1 backplane.
• Same as O9550-A except All interfaces, cross-connect, encapsula on, filtering, alarms are set through console/SNMP ports, over
• 4 slots and 4 mini slots TS or DCC in Text menu, Windows cra , iNET-NMS and iNMS with automa c commissioning in SNMP.
• DACS 504+36 E1 x 31TS
or 672+27 T1 x 24TS
High Density DS0 DACS, E1/T1, T3 M13, STM1/OC3
This high density cross-connect system is used by Telco operator to groom and cross connect leased
lines or specialized applica ons for large public applica ons and to convert voice traffic from E1 law A
to T1 law µ between con nents.
This system is also used by the different large Power companies to groom and cross-connect up to 672
T1 from remote sites with the high level of reliability and very short latency.
Many V4150 can be linked together directly over STM1/OC12 interfaces or to a O9400R to mul ply the
density of E1 or T1 interfaces. To provide 1:N protec on on E1/T1 we can daisy chain a Protec on Relay
V4150R Shelf . The V4150 supports E1 120/75ohms, T1, T3 interface with mul plexing M13 to 28 T1 and G.727
6U Modular PDH DACS DS0 T3 to 21E1. All interfaces E1, T1, T3 and STM1/OC3 use the same clock synchroniza on.
with redundant CPU and PS All circuits cross connec on of this chassis and eventually remote chassis can be operated by iNMS sys-
• 8 slots for 63 E1/T1, 3 T3 or tem with an automa c commissioning which saves CAPEX and OPEX when customers renew the ex-
2 STM1/OC3 interface is ng installa on.
• DACS 504 E1 x 31TS
or 672 T1 x 24TS
www.LoopTelecom.com
Page 4
Ethernet, SCADA, Teleprotection, Voice for Energies plan & grid
Many installa ons in Oil and Gaz or Chemical complex are managing As par cular features we support Point to Mul point interfaces
the process control and SCADA over Ethernet RTU. But as the site with pooling communica on mode between central and remote
was installed more than 10/20 years ago several applica ons are for analog connec on or RS232/RS485 applica ons.
always based on analog RTU, or with integrated modem to provide We also support the SCADA automa c communica on from nodes
the ming informa on or low rate asynchronous or synchronous to two working and standby NTU.
communica on. The Loop DACS care for all applica ons and provide Thanks to the TDMoE cards, the AM3440/O9550 can also encapsu-
the absolute QoS for applica on based also on IP transport. late these signals to cross Ethernet pipes.
We have integrate several protocol, but we can transmit all signals Then the customer will be able to migrated step by step his applica-
transparently for proprietary applica on. ons and WAN to Ethernet/Gigabit Ethernet.
Ethernet Transport over PDH - EoPDH support up to 8Mbps in MLPPP over 4 E1.
All Loop TDM/PDH devices can carry bridged or routed Ethernet These cards with 2 or 8 LAN support VLAN, Q-in-Q, VLAN-ID map-
over FE1 or group of E1. The Router/Bridge cards support up to 64 ping and QoS .
WAN. Bandwidth of each WAN can be set from n x 64Kbps to 2Mbps These cards are suppor ng Sta c rou ng, RIP 1 and 2 and OSPF
with HDLC, HDLC Cisco, PPP-BCP, PPP routed or Frame Relay or can over WAN or LAN interfaces.
www.LoopTelecom.com
Page 5
E1 Converters, T1 CSU/DSU and Multiplexer
Loop E1 or T1 TDM/PDH Loop Telecom has manufactured since 1991 CSU/DSU for E1 and T1 public and pri-
converters supports un- vate Telco operator to install in customer premise and deliver data or data with
framed or framed lines at n voice service. These products are not only interface converter but termina on line
x 56kbps or n x 64kbps for with high monitoring. For large WAN infrastructure we have implemented two DTE
different applications. mux func on and SNMP router management with secure Radius access to op mize
the OPEX cost.
E1/T1 Converter and Dual ports Multiplexer
The E1510-S and E1500-2S are E1 converter for also 8 alarm inputs to generate SNMP trap dry
E1 WAN 75ohms with dual BNC and 120ohms contacts change on AM3440 with dry contact
with RJ48 female connectors for G.703 networks. card. One or two Bridge or Router interfaces can
Both support unframed 2.048 kbps and framed support up to 31 WAN HDLC or PPP.
G.704 n.64kbps, with n = 1 to 31. The E1500-2S These devices can be supplied as E1/T1 drop &
also supports n.56kbps. We can select each TS insert mul plexer with one E1/T1 local interfaces
per interface and not necessarily con guous. and a DTE or Ethernet.
E1510-S E1510-S is an economic E1 converter with single They are full CSU/DSU, we can access remotely to
Economic E1 G703 / FE1 G704 DTE or Bridge interfaces set by DIP-switches. Line the line and DTE interfaces over TS in Telnet/SSH
Interfaces Converter supports: and DTE loopback can be done locally during the or SNMP or locally with RS232 port. We can
• E1, HDB3, 75 and 120 ohms installa on and an auto-test give the status of remotely launch the loop tests, get performance
• 1 DTE interface : the converter on LED. of last 24 hours with 15mn test, last 7 days in 24h
E1500-2S and T2500-2S are more sophis cate summary line. We can get the alarm history of
• X21 or V35 or
devices with one or two DTE or Bridge or Router WAN line and DTE and the Threshold: Bursty
• 10/100BT Ethernet bridge Seconds, Severely Errored Second, Degraded
interfaces. DTE interfaces can order X21, V35,
• Rate n x 64Kbps n=1-32 IEA530, RS232 or G703 64K codirec onal, but Minutes .
• Dip-switches selec on
E1500-2S
CSU/DSU E1 2Mbps G703,
FE1 G704 Mul plexer:
E1500-2S and T2500-2S can share easily a 2Mbps E1 line with a FE1 for PBX as E1-CAS or E1-ISDN or T1
• WAN G703/G704/E1-CAS
voice and a LAN transport. This line can be a single dual copper pair line of maximum 1.5km without any
• E1, AMI/HDB3, 75/120 Ω
network to carry simple or double interfaces like an economic DSL line.
• 1 or 2 DTE interfaces with
TS0 selec on, as:
BTS deployment
• X21,V35,IEA530,RS232 or
G703 64K codirec onal
• 10/100BT Bridge or Router
• 8 Alarm inputs
• Rate n x 56/64Kbps n=1-32
• In-band menu and SNMP
management HDLC/PPP
• Line and DTE interfaces
remote monitoring and loop
T2500-2S
CSU/DSU T1 1.544Mbps FT1
D4/ESF framing supports:
• WAN T1, AMI/B8ZS, 100 Ω
• 1 or 2 DTE interfaces with
DS0 selec on, as: Loop Telecom supplies AM3440 DACS mul plexers and E1500-2S and T2500-2S line termina ons to
• X21,V35,IEA530,RS232 or
deploy BTS for 2G or 3G in E1-EMI or BTS for different trunking radio or Private Radio Mobile Radio
G703 64K codirec onal
(PMR) named also Land Mobile Radio (LMR). The E1 transports generally the voice and data mobile in-
• 10/100BT Router
• Rate n x 56/64Kbps n=1-24 forma on but also the management and access control of the BTS. E1500-2S and T2500-2S provide both
• In-band menu and SNMP interfaces E1, E1-IMA or X21 for payload and Ethernet, RS232, X21 or only dry contacts for BTS admin-
management HDLC/PPP istra on according to the mobile technologies. The E1550-2S /T2500-2S economical end of line devices
• Line interface monitoring are Telnet/SSH HDLC or SNMP v3 manageable from central site or by iNET or iNMS central NMS system.
and loops
www.LoopTelecom.com
Page 6
Management, Monitoring of SDH, PDH, OTN, PW3E and MPLS-TP
www.LoopTelecom.com
Page 7
Multiservice Access Multiplexer - PDH/TDM DACS
E1500-2S AM3440-B
Models E1510-S AM3440-A AM3440-D O9550R-A O9550R-C V4150
T2500-2S AM3440-C
E1/T1 CSU/DSU HYBRID PDH DACS PDH DACS
E1 converter PDH/TDM DACS
Mul plexer & SDH/SONET SDH/SONET
System Desktop 1U tray Desktop 1U tray Modular 5U ETSI Modular 2.5U / 3U Modular 2U ETSI Modular 5U ETSI Modular 3U ETSI Modular 6U ETSI
1 CPU 1 SNMP CPU 2 redundant SNMP CPUs 2 redundant SNMP CPUs 2 red. SNMP CPUs
AC or DC or AC&DC AC or DC 2 DC48v redundant AC or 2 DC48v red. AC or 2 DC48v red. 2 DC48v redundant AC or 2 DC48v red. 2 DC48v redundant
1 E1/FE1 or Any E1 or T1 interfaces can set as WAN interfaces 4 STM1/4 Any E1, T1, STM,
Aggregate interfaces 1 E1/FE1
1 T1/FT1 OC interfaces
SNCP-PDH 64k with 2 x 3E1-SNCP card, E1/T1 1+1 ports 2 ring SNCP or 2 MSP
SDH func on - - - ADM, TM, cross-c. VC11/VC12/VC3/V4 VC11/VC12/VC3/V4
WAN: 1 E1/FE, trib: 31x64kbps or 2Mb 64E1 / 52T1, B=28E1/16T1, 36E1/ 9T1, 4 x 63E1+ 64E1 or 4 x 63E1+ 36E1 or 504 E1/672 T1 DS0,
PDH backplane 31x64kbps or 2Mb 24x56/64kbps,1.5M 128Mbps C=36E1/24T1, 72Mbps 4 x 63T1 + 52T1 4 x 63T1 + 24T1 8 STM1/OC3
PDH cross connect No DS0 Mul plexer Full non blocking DACS
PDH protec on - - E1/T1 1+1, SNCP-64K circuits, ULSR-PDH circuits E1/T1 1+1, SNCP 64K circuits E1/T1 1+1
4 mini slots, 4 mini slots, 4 mini slots, 4 mini slots,
Tributaries 1 1 or 2
12 slots B= 3slots, C=5slots
9 mini slots
12 slots 5 slots
8 slots
FE1/FT1 card - 0 to 2 FE1 or FT1 1 or 4 E1 or T1, 4E1 or T1 fiber 1 or 4E1 or T1, 1FO 1 or 4 E1 or T1, 4E1 or T1 fiber 63E1,63T1,3T3MX3
G703 64k - 0 or 1 co-direc on. 8 co-direc onal or contra-direc onal - 8 co-direc onal or contra-direc onal -
Voice FXO, FXS - - cards 4/12FXS or 4/12FXO cards 4FXS or 4FXO cards 4/12FXS or 4/12FXO -
E&M, Magneto - - cards 4 and 8E&M 2/4w and 8 Magneto cards 4 E&M 2/4w cards 4 and 8E&M 2/4w and 8 Magneto -
Conference - - card 2FXS, 2E&M and 2RS232 - card 2FXS, 2E&M and 2RS232 -
PLM - - cards PLM Line or Monitor cards PLM line/Mon cards PLM line or Monitor -
X21/V35/IEA530/ 0 or 1 X21/V35/ cards: 1 X21, 1 V35, 1 V36, 1 RS232 or cards: 1 X21, 1 V35, cards: 1 X21, 1 V35, 1 V36, 1 RS232 or
0 or 1 X21/V35 -
RS232 IEA530/RS232 4 X21/V35/EIA530 or 6 RS232 1V36, 1 RS232 4 X21/V35/EIA530 or 6 RS232
Rate n x 64Kbps n x 56 or 64Kbps n x 56 or 64Kbps n x 56 or 64Kbps n x 56 or 64Kbps n x 56 or 64Kbps n x 56 or 64Kbps n x 56 or 64Kbps
Sub-rate 64Kbps - - X50 or V110 X50 or V110 X50 X50 or V110 X50 or V110 -
RS232/RS485 async - - 8 RS232/RS422/RS485 async, X50, TS card 3 TS 8 RS232/RS422/RS485 async, X50, TS -
C37.94 - - cards 1 or 4 FO card 1 FO cards 1 or 4 FO -
Teleprotec on TTA - - 2 slots card for 4 ports - 2 slots card for 4 ports -
OCU-DP - - cards 1 or 8 OCU-DP card 1 OCU-DP cards 1 or 8 OCU-DP -
Dry contacts - 0 or 8 inputs Card 8 inputs / 8 outputs - Card 8 inputs / 8 outputs -
G.SHDSL see H3310 see H3300-3S cards 4 G.SHDSL 2W or 2 G.SHDSL 2/4w - cards 4 G.SHDSL 2W or 2 G.SHDSL 2/4w -
ETHERNET EoPDH E-Line E-Line, E-LAN E-Line, E-LAN E-Line, E-LAN E-Line, E-LAN -
Bridge 1 x 10/100BaseT 0 to 2 x 10/100BaseT 2 x 10/100Bt mini cards Bridge/Router, 2x10/100Bt mini 2 x 10/100Bt mini cards Bridge/Router,
-
Router - 0 to 2 x 10/100BaseT 8 x 10/100Bt card Switch/Bridge/Router card, Bridge/Router 8 x 10/100Bt card Switch/Bridge/Router
1 WAN 31 or 24 WAN 32 or 64 WANs per card from 32 WANs per card 32 or 64 WANs per card from
Nb WAN and BW n.64kbps to 2Mbps n.64kbps to 2Mbps 64Kbps to 2 or 8Mbps MLPPP n.64kbps to 2Mbps 64Kbps to 2 or 8Mbps MLPPP
-
Encapsula on - - TDMoE card: 2GE WAN and 2GE LAN - TDMoE card: 2GE WAN and 2GE LAN -
CESoPSN, SAT, AAL1 - - Supports 64K to 8MB over 64 PW-3E - Supports 64K to 8MB over 64 PW-3E -
Environment Fanless Fanless Fanless Fanless Fanless Fanless Fanless Fan
438 x 110 x 224 mm
Size (WxHxD) 210 x 41.5 x 140 mm 216 x 55 x 285 mm 432.4 x 220 x 224mm
438 x 132 x 224 mm
438 x 88 x 224 mm 432.4 x 220 x 224mm 438 x 132 x 224 mm 433 x 264 x 223.5 mm
Temperature -5 to +55°c 0 to +50°c -10 to +55°c -10 to +55°c -10 to +55°c -10 to +55°c -10 to +55°c -10 to +55°c
Standard compliances FCC Part 15 Subpart B, Class A - CE - Safety IEC60950-1
Other compliances IEC61850, EN50121-4* IEC61850, EN50121-4*
Management Telnet Cra Telnet Cra Telnet/SSH Cra Telnet/SSH Cra Telnet Cra Telnet/SSH Cra Telnet/SSH Cra Telnet Cra
Local Port, over TS RS232 and TS RS232, Eth and TS RS232, Eth and TS RS232, Eth and TS RS232, Eth and TS and DCC SDH RS232, Eth and TS
SNMP from AM3440 v1, v3 v1, v3 v1, v3 v1, v3 v1, v3 v1, v3 v1, v3
LCT Interface Node administra on Windows GUI
iNET (EMS) Windows GUI , Graphic cross connect, vision of programed circuit
iNMS (NMS) Support Transport, Access, PW3R or MPLS-TP circuits, automa c nodes commissioning, synchroniza on,
* in development or qualifica on
www.LoopTelecom.com
Page 8