FR EN DE IT ES NL PT RU PL TR ZH
INDEX
2. INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4. QUICK START. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5. GENERAL OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.1. ATyS s & ATyS sd : RTSE « Product introduction » . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.2. ATyS : RTSE « Product identification ». . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.3. ATyS s and ATyS sd : RTSE « Environmental details» . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.3.1. IP Rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.3.2. Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.3.2.1. Temperature / Current Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.3.2.2. Temperature / Control Voltage Limits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.3.2.3. Hygrometry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.3.2.4. Altitude. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.3.3. Storage Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.3.3.1. Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.3.3.2. Storage duration period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.3.3.3. Storage position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.3.4. Volume and shipping weights : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.3.5. CE Marking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.3.6. Lead Free Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.3.7. WEEE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.3.8. EMC standard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6. INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6.1. ATyS s and ATyS sd : RTSE « Product dimensions » . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6.2. ATyS : RTSE « Mounting Orientation » . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6.3. ATyS : RTSE «Assembly of Customer Mounted Accessories». . . . . . . . . . . . . . . . . . 16
6.3.1. Bridging bar installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.3.2. Terminal Shrouds. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6.3.2.1. Outgoing Terminal Shrouds (When using bridging bars). . . . . . . . . . . . . . . . . . . 17
6.3.2.2. Incoming Terminal Shrouds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6.3.2.3. Sealing Facility for added security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6.3.3. Direct handle and storage clip. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7. CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
7.1. Power Circuits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
7.1.1. Cable Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
7.1.2. Power Connection Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
7.1.3. Power Connection Sectional Area. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
ENGLISH
7.2. Control Circuits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7.2.1. Typical ATyS s and ATyS sd wiring diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7.2.1.1. ATyS sd : 230Vac x 2 (Dual Power Supply) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7.2.1.2. ATyS s : 230Vac. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.2.1.3. ATyS s : 12Vdc. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.2.1.4. ATyS s : 24/48Vdc. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7.2.1.5. External Power Supply (400Vac). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7.2.2. ATyS s RTSE + ATS Controllers type ATyS C30 and ATyS C40. . . . . . . . . . . . . . . 23
7.2.3. ATyS s and ATyS sd Input and Output Contacts. . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7.2.4. Terminal denomination, description and characteristics. . . . . . . . . . . . . . . 24
9. ATyS s CHARACTERISTICS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
• V
oltages associated with this product may cause injury, electric shock, burns or death. Prior to carry out any
maintenance or other work on live parts or other parts in the vicinity of exposed live parts, ensure that the
switch including all control and associated circuits are de-energized.
DANGER
DANGER
DANGER
WARNING
WARNING
WARNING
CAUTION
CAUTION
CAUTION
Risk : RISK : RISK :
Electric shock, burns, death Possible personal injury Equipment damage
• As a minimum the ATyS s and ATyS sd comply with the following international standards:
- IEC 60947-6-1 - IEC 60947-3
- GB 14048-11 - IS 13947-3
- EN 60947-6-1 - EN 60947-3
- VDE 0660-107 - NBN EN 60947-3
- BS EN 60947-6-1 - BS EN 60947-3
- NBN EN 60947-6-1
The information provided in this instruction manual is subject to change without notice, remains for general
information only and is non-contractual.
2. INTRODUCTION
ATyS s family of “remotely operated transfer switching equipment” (RTSE) are designed for use in power systems
for the safe transfer of a load supply between a normal and an alternate source. The changeover is done in open
transition and with minimum supply interruption during transfer ensuring full compliance with IEC 60947-6-1, GB
14048-11 and other international TSE standards as listed.
The ATyS s and ATyS sd are full load break (switch type) derived transfer switching equipment where the main
components are proven technology devices also fulfilling requirements in IEC 60947-3 standards.
As Class PC RTSE, the ATyS s and ATyS sd products are capable of “making and withstanding short circuit currents”
assigned to IEC 60947-3 utilization categories of up to AC23B, GB 14048-11, IEC 60947-6-1 and equivalent
ENGLISH
standards with utilization categories of up to AC32B.
ATyS C30 ATyS D10 ATyS C30 ATyS D20 ATyS C40
atys-s 027 B
atys-s 028 B
atys-s 026 C
ATyS S ATyS S
ATyS Sd
SOCOMEC has been manufacturing power control and safety products since 1922. The first generation SOCOMEC
“motorised changeover switches” were introduced in 1990 and today the ATyS brand has become trusted by major
players in the power industry worldwide.
The ATyS Family includes a complete range of remotely operated transfer switch equipment (RTSE) as well as
automatic fully integrated products and solutions (ATSE). Selecting the right ATyS will depend on the application as
well as the nature of installation in which the ATyS will be installed.
This instruction manual includes details and instructionS specific to the “ATyS s and ATyS sd” RTSE only. For all
other ATyS Family of products please refer to the specific instruction manual related to that product. (Available for
download on www.socomec.com).
40A - 160A
Back to Back
Configuration
ATyS p
Power / Genset ATyS M6e
Management Evolved Genset
Management
ATyS g
Simple Genset ATyS M6s
40A - 125A
ENGLISH
Source availability LED display • • • •
Remote Display module RJ45 connection for ATyS D10 • • • ATyS D20
Integrated Dual Power Supply • • • • •
Network - Network Applications • • • • • •
Network - Genset Applications • • • • • •
Genset - Genset Applications • • • •
Pre-defined fixed I/O • 5/1 • 5/1 • 9/2 • 11/3 • 5/2
Programmable I/O • 6/1
Additional programmable I/O modules (Optional up to 4 modules) • 8/8
Remotely operated Transfer Switching Equipment
(RTSE Class PC) • • • •
Automatic Transfer Switching Equipment (ATSE Class PC) • • •
Remote + Manual Control • • • •
Auto + Remote + Manual Control • •
Auto + Remote + Local + Manual Control •
Auto-configuration of voltage and frequency levels • • •
Switch Position LED display • • •
Security Sealing Cover • •
Configuration through potentiometers and dip switches • •
Test on load functionality • •
Test off load functionality • •
Programmable configuration with keypad and LCD display •
Metering & Measurement: kW; kVar; kVA + kWh; kVarh; kVAh •
Communication RS485 + Ethernet + Ethernet gateway (Optional) •
Webserver Access through optional Ethernet module (Optional) •
Easy Configuration software (Through Ethernet/Modbus) •
Remote Terminal Unit RJ45 connection for ATyS D20 •
Data Logger for Event Recording with RTC
(Through Ethernet/Modbus) •
Programmable Engine Exerciser functionality
(Through Ethernet/Modbus) •
Multi level password access •
Load Shedding function •
Capacity Management functionality •
Peak shaving functionality •
4 - 20mA communication module (Optional) •
KWh Pulsed output module (Optional) •
Counters KWh, permutation… •
LCD display for programming, metering, timers and counters •
Possibility to add optional functionality •
ATyS S / Sd
Motorised Source Changeover Switch
STEP 1
Cabinet / Back
Plate Installation
STEP 2
Connecting the
POWER Section
STEP 3
COMMAND /
CONTROL terminal
connections
STEP 4
Power Supply
terminal
connections
STEP 5
Emergency
Handle mounting
STEP 6
Check
STEP 7B
Emergency Manual
Operation
STEP 7C
Preliminary operations Padlocking
Check the following upon delivery and after removal of the
packaging:
n Packaging and contents are in good condition.
n The product reference corresponds to the order.
n Contents should include: STEP 3
Qty 1 x ATyS S / Sd product
Qty 1 x handle and storage clip
Quick Start instruction sheet
Qty 1 set of 3 terminal connectors
Qty 1 set of 16 screws, nuts and washers for connecting
the power section.
Warning
Risk of electrocution, burns or injury to persons and /
or damage to equipment.
This Quick Start is intended for personnel trained in the
installation and commissioning of this product. For further
details refer to the product instruction manual available on
the SOCOMEC website.
n This product should always be installed and commissioned
by qualified and approved personnel..
n Maintenance and service operations should be performed
by trained and authorised personnel.
n Do not handle any control or power cables connected to
the product when voltage may be, or may become present
on the product, directly through the mains or indirectly
through external circuits.
n Always use an appropriate voltage detection device to
confirm the absence of voltage.
n Ensure that no metal objects are allowed to fall in the
cabinet (risk of electrical arcing).
Failure to observe good enginering practises as well as to
follow these safety instructions may expose the user and
others to serious injury or death.
Aux 11
IEC IEC
60947-6-160947-3 STEP IEC
4 IEC GB
Risk of damage the device14 60947-6-160947-314048-11
Ue n In case
240V the product is dropped
240V 21 or damaged in any way it 240V 240V
Fn 50/60Hz 50/60Hz
Class is recommended
PC to replace the complete product. 50/60Hz 50/60Hz
PC
AC-33B AC-23A
24 Class
Ie 125A Ie 125A AC-33B AC-23A
Ie 125A AC-32A AC-32A
01 Motorised Changeover Switch Motorised Changeover Switch
Ie 125A
Icw / Icm 10/17kA
Accessories
Icw / Icm 10/17kA
Uimp power 6kV 125A 125A
Ue 125A
Fn n Secure 50Hz Connector Bracket. I I I
Ref.: 88888888
Fn
Class PC
315 Whilst in manual mode, check the
n
Ie 125A Voltage
AC-33B taps. wiring and if ok power up the
Ie 125A AC-32A
n DIN-rail
Icw / Icm
4 modules.
316 ATyS S ATyS Sd product.
code à barres
Uimpn ATS6kVController type
power
317ATyS C30 + D10/D20.
Uimp control 2,5kV C
n ATS50kA
Icc prospect. Controller type ATyS C40.
(fuse 125AgG)
For further detailsCTRLrefer to the product instruction manual
under chapter "Spares and Accessories"
STEP 7A Automatic Operation
AUT
Ensure that the emergency handle
is not inserted in the product, and
de projet de KIT étiquettes ATyS S / Sd comprenant : turn the mode selector to the AUT
position.
un ensemble d’étiquettes concernant le Sircover avant montage de la motorisation
___________________________________________________________
position I
position 0
position II
Printing size: 420x297. Final size 210x148. This page visible first. the desired position.
Ø 4-8 m Order Priority:
m I and II are equal priority over 0. Should
I and II be closed simultaneously the
541 891 C - 05/13 - EN
Non contractual document.
Subject to change without notice. product will not change position.
STEP 1 Installation
All dimensions in mm.
Attention: Ensure that the product is installed on a flat rigid surface. 104.5 8 15
Orientation: 11 26.5 27.5 26.5
Recommended Ok Ok 37
72
40A -
50 50
143.5
125A
90.6
106
113
94
72
25
ENGLISH
Detailed fixing point: O° - 45° - 90° 115.2 74 44
198 100
181 42.5
AUT
3
45
16
Ø 6.4
40 A 63 A 80 A 10 0 A 125 A
Minimum cable sec-
tion Cu (mm2) at Ith 10 16 25 35 50
Maximum cable
section Cu (mm2) 70 70 70 70 70
Type of screw M6 M6 M6 M6 M6
2
Recommended tight-
ening torque (N.m) 4.5 4.5 4.5 4.5 4.5
Maximum tightening
torque (N.m) 5.4 5.4 5.4 5.4 5.4
201202
O I II
ATySCTRLS ATyS Sd
AUX. CONTACTS
ATyS S: 230 VAC
1 2
Fus. 4 A
gG type *Torque
Screw M3
301302
Bande
STEP5 de 80mm de largeur et Marquages fixes
317 316 315 314 04 03 24 23 14 13
Handle Storage Assembly
O I II
CTRL AUX. CONTACTS
ATyS S DC version: 12 VDC / 24-48 VDC
1
1 2
Screw M3
*Tightening torque:
401402
min.: 0.5 Nm
ATyS
2 s alim 2 sources 230Vac
DC
O I II
CTRL AUX. CONTACTS
1
11 2
d 3
4
10
5
6
c 7
8
b
9
1 2 3
ENGLISH
4
ATyS Sd
5
AUT
Ø 4 ... 8mm
9
XXXXXXXX
12 11 10
1. Switch 1 (Front) and Switch 2 (back) identification labels (Top & Bottom)
2. Output contacts identification label.
3. Input contacts identification label.
4. Main changeover switch identification label including:
Electrical characteristics & Applicable standards
5. ATyS Product Type (ATyS s or ATyS sd)
6. ATyS s / ATyS sd current rating and product reference number
7. Product Type pictogram (RTSE – Motorised Changeover Switch)
8. Power Terminals incoming and outgoing wiring details.
9. Complete ATyS product serial number, barcode and CE marking.
10. Auxiliary power supply contacts and identification label
11. Switch position and mechanical interlock pictogram
12. Direction of rotation for emergency manual operation
5.3.1. IP Rating
ø 1 mm
5.3.2.3. Hygrometry
• 80% humidity without condensation at 55°C
• 95% humidity with condensation at 40°C
5.3.2.4. Altitude
• Up to 2000m in altitude without derating
• For higher altitude the Ka correction factors below apply
5.3.3.1. Temperature
• From -40 to +70°C
ENGLISH
• (Recommendation: To be stored in dry, non corrosive and non saline atmospheric conditions)
5.3.5. CE Marking
The ATyS s and ATyS sd comply with the European directive for :
• The Electromagnetic compatibility no. 2004/108/CE dated 15th of December 2004.
• Low voltage directive no. 2006/95/CE dated 12th of December 2006.
Class B products :
Products intended to be installed in an industrial, commercial or residential environment.
6. INSTALLATION
37
ENGLISH
72
50 50
143.5
90.6
106
113
94
angle de 58°
Commutateur
IEC IEC GB
60947-6-160947-314048-11
240V 240V
25
Angl e
Angl
50/60Hz 50/60Hz
e 58°
Class PC
58°
Ie 125A AC-33B AC-23A
Ie 125A AC-32A
Icw / Icm 10/17kA
Uimp power 6kV
Uimp control 2,5kV
Icc prospect. 50kA
(fuse 125AgG)
code à barres
AUT
115.2 74 44
198 100
302 - N
301 - L
230V
Aux Supply
(160-310V )
181 42.5
code à barres
402
401
12V
Aux Supply
(9 - 15V
)
ATyS s 24Vdc
code à barres
(7 modules):
M6 125
402
401
24 - 48V
Aux Supply
(17 - 62V
)
Ø 4 ... 8mm
code à barres
2
AUT
AUT
3
45
16
202 - N
201 - L
102 - N
101 - L
230V
Aux Supply
(160-310V )
Aux 2
Aux 1
Motorised Changeover Switch
125A Ref : 95054012
code à barres
XXXXXXXX
ATyS S
(fuse 125AgG)
Icc prospect. 50kA
Uimp control 2,5kV
Uimp power 6kV
Icw / Icm
Ie 125A
Ie 125A
Class
Fn
Fn
Ue
Ue
(fuse 125AgG)
Icc prospect. 50kA
Uimp control 2,5kV
Uimp power 6kV
Icw / Icm
Ie 125A
Ie 125A
Class
Fn
Ue
60947-6-160947-3
10/17kA
AC-32A
AC-33B AC-23A
PC
50/60Hz 50/60Hz
240V
AC-32A
AC-33B
50Hz
240V
GB 14048-11
PC
IEC
240V
IEC
2A / 24V
2A / 250V
CTRL
Aux
317
316
315
314
C
04
01
24
21
14
11
125A
Motorised Changeover Switch Motorised Changeover Switch
Ref : 95054012
ATyS s alim 1 source 230Vac
ATyS S
To consider the space required for mounting (storage) of the manual operation
ARNING CAUTION
125A
Ref : 95054012
handle as well as the wiring.
ATyS Sd
Ø 4 ... 8mm
Ref.: 88888888
125A
ATyS S
(fuse 125AgG)
Icc prospect. 50kA
Uimp control 2,5kV
Uimp power 6kV
Icw / Icm
Ie 125A
Ie 125A
Class
code à barres
60947-6-160947-314048-11
10/17kA
AC-32A
AC-33B AC-23A
PC
50/60Hz 50/60Hz
240V
IEC
Aux 11
240V
IEC IEC
IEC
60947-6-160947-3 IEC IEC GB
14 60947-6-160947-314048-11
Ue 240V 240V 21 240V 240V
GB
Fn 50/60Hz 50/60Hz 50/60Hz 50/60Hz
Class PC PC
AC-33B AC-23A
24 Class
Ie 125A Ie 125A AC-33B AC-23A
Ie 125A AC-32A AC-32A
01 Motorised Changeover Switch Motorised Changeover Switch
Ie 125A
Motorised Changeover Switch Motorised Changeover Switch Motorised Changeover Switch
Icw / Icm 10/17kA Icw / Icm 10/17kA
Uimp power 6kV 125A 125A 125A Ref : 95054012
code barres KIT
Ue 240V
314 125A
Ue
Fn 50Hz Ref.: 88888888
Fn
Class PC
Ie 125A AC-33B
315
Ie 125A
Icw / Icm
AC-32A
316 ATyS S ATyS Sd code à barres ATyS S ATyS Sd ATyS S code barres KIT
Maximum cable
Motorised Changeover Switch Motorised Changeover Switch
70 70 70 70 70
XXXXXXXX XXXXXXXX XXXXXXXX
section Cu (mm2)
Exemple de projet de KIT étiquettes ATyS S / Sd:
ATyS S
Bande de 80mm de largeur et Marquages fixes
Motorised Changeover Switch Motorised Changeover Switch
Motorised Changeover Switch
ATyS Sd
ATyS S
ATyS S
ATyS Sd
125A
Motorised Changeover Switch
125A
Motorised Changeover Switch
AUT
AUT
Ø 4 ... 8mm
AUT
Ø 4 ... 8mm
Ø 4 ... 8mm
Type of screw M6 M6 M6 M6 M6
ATyS s alim 2 sources 230Vac
Ref : 95054012
Ref : 95054012
Ref : 95054012
Ø 4 ... 8mm
Ø 4 ... 8mm
Ø 4 ... 8mm
ATyS Sd
2
ATyS Sd
ATyS S
ATyS S
Ø 4 ... 8mm
AUT
125A
AUT
AUT
AUT
Recommended tight-
ATyS S
ening torque (N.m) 4.5 XXXXXXXX 4.5 4.5 XXXXXXXX 4.5 4.5
ATyS s alim 2 sources 230Vac ATyS s alim 1 source 230Vac ATyS s 24Vdc
Maximum tightening
XXXXXXXX
1
Exemple de projet de KIT étiquettes ATyS S / Sd comprenant :
CTRL
(fuse 125AgG)
Icc prospect. 50kA
C Uimp control 2,5kV 402 402
317 Uimp power 6kV
(160-310V ) (160-310V )
code à barres
code à barres
code à barres
Ie 125A AC-33B
315 Class PC
à droite : un ensemble d’étiquettes concernant le Sircover avant montage de la motorisation
14
AC-33B AC-23A
gle de 58°.
IEC
ARNING CAUTION
11 Aux
10/17kA
AC-32A
IEC
code à barres
240V
Ref.: 88888888
PC
ATyS S
Icw / Icm
Ie 125A
Ie 125A
Class
125A
AUT
ATyS s alim 1 source 230Vac
Ø 4 ... 8mm
Exemple de projet de KIT étiquettes ATyS S / Sd comprenant :
ATyS Sd
s
ATyS S
125A Ref : 95054012
14
21
24
01
04
11
C
2A / 250V
CTRL
2A / 24V
314
315
316
317
Aux
50/60Hz 50/60Hz
60947-6-160947-3
AC-33B AC-23A
240V
IEC
GB 14048-11
1 2
10/17kA
AC-32A
AC-33B
AC-32A
240V
50Hz
PC
PC
(fuse 125AgG)
(fuse 125AgG)
Icw / Icm
Icw / Icm
Ie 125A
Ie 125A
Ie 125A
Ie 125A
nnect the
Class
Class
Ue
Ue
Ue
Fn
Fn
Fn
ATyS S
XXXXXXXX
d suitable
code à barres
Aux Supply
Fus.Changeover
Motorised 4 A Fus. 4 A
Switch Motorised Changeover Switch
Aux 1
Aux 2
*Torque
(160-310V )
202 - N
101 - L
201 - L
230V
gG type gG type
101102
201202
AUT
)
24 - 48V
(17 - 62V
401
402
yS s 24Vdc
code à barres
6.3. ATyS : RTSE «Assembly of Customer Mounted Accessories»
Never handle any customer mounted accessories while there may be the risk of
DANGER WARNING
voltage being or becoming present. CAUTION
Bridging bars are delivered complete (4P copper bars rated at 125A Ith) together with associated bolts nuts and
washers. For ease of installation onto the ATyS s terminals, fixing of bridging bars is recommended to be carried out
prior to fixing the unit onto a backplate.
It is recommended to first install the bar closest to the motorization module followed by the adjacent bar until all 4
poles are installed. Pay attention to the tightening torque recommendations below.
Note:
Switch II screws and washers should be mounted from the rear towards the front using the nuts fixed to the bridging bars
for retaining. These replace 4 retaining nuts initially delivered loose with the switch therefore those 4 off extra nuts should be
discarded. Switch I screws and washers should be mounted from the front towards the rear using the loose nuts provided fit into
the back of the switch terminals.
Bridging bars may be fit as Top or Bottom in the same manner as described above.
40A to 125A
Type of screw M6
ENGLISH
/ Sd
shaft must be removed from the handle by removing the central retaining screw on the handle. This will convert the
STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6 Recommended Ok Ok
male hexagon
Cabinet / Back shaft
Connecting the into
COMMANDa/ 10mm female
Power Supply direct handle
Emergency Check compatible
STEP 7B
Emergency Manual
with the
40A -
bare switch mechanism.
Plate Installation POWER Section CONTROL terminal terminal Handle mounting
connections connections Operation 125A
geover Switch
90.6
106
94
ENGLISH
The emergency direct handle storage clip has been designed to fit virtually anywhere:
STEP 7C
ns • Din rail mounting Padlocking
after removal of the
o the order.
STEP 3
2
3
16
Ø 6.4
hers for connecting
ry to persons and /
nnel trained in the
product. For further
STEP 2 Power Terminal Connections
To be connected using terminal lugs, rigid or flex
manual available on
• Clipped directly into the side of the ATyS s • C
lipped into the top or bottom secure connector 40 A 63 A 80 A 10 0 A 1
d and commissioned
.. bracket accessory. Minimum cable sec-
tion Cu (mm ) at Ith 10 2 16 25 35
should be performed
Maximum cable
section Cu (mm2) 70 70 70 70
cables connected to Type of screw M6 M6 M6 M6
may become present
mains or indirectly Recommended tight-
ening torque (N.m) 4.5 4.5 4.5 4.5
Maximum tightening
detection device to torque (N.m) 5.4 5.4 5.4 5.4
ctises as well as to
xpose the user and
CONTROL /
STEP IEC
4 IEC GB
60947-6-160947-314048-11
STEP3 COMMAND Terminals
ATyS Sd: 2 x 230 VAC
maged in any way it 240V 240V
plete product. Class
50/60Hz 50/60Hz
PC 1
Ie 125A AC-33B AC-23A Ensure that the product is in manual mode and connect the
Ie 125A AC-32A product controls using the supplied connectors and suitable
orised Changeover Switch Motorised Changeover Switch Icw / Icm 10/17kA
cable of section 1.5 - 2.5 mm² . Fus.
Motorised 4 A
Changeover Fu
Switch Motorised Changeover Switc
A 125A gG type gG
code barres KIT
101102
201202
Uimp control 2,5kV
Icc prospect. 50kA
d technical manuals:
STEP
STEP 7C1 Padlocking mode (in position O)
order 0
order II 1
ATyS S DC version: 12 VDC / 24-48 VDC
position I 1
position 0
position II
STEP 3
401402
Fus. 4
aper 90g/m2. Close the contact corresponding to gG ty
his page visible first. 3x the desired position. 317 316 315 314 04 03 24 23 14 13
Ø 4-8 m Order Priority:
m I and II are equal priority over 0. Should O I II
I and II be closed simultaneously the CTRL AUX. CONTACTS
ual document.
ange without notice. product will not change position.
Motorised Changeover Switch
ATyS S
AUT
AUT
Ø 4 ... 8mm
Ø 4 ... 8mm
125A Ref : 95054012
ATyS S
AUT
7. CONNECTIONS
Ø 4 ... 8mm
Ref : 95054012
7.1. Power Circuits
125A
40A to 125A
Recommended tightening torque (N.m) 4.5
Type of screw M6
All values are indicative
40A to 125A
lation
All dimensions in mm.
uct is installed on a flat rigid surface. 104.5 8 15
11 26.5 27.5 26.5
Ok Ok 37 72
50 50
143.5
90.6
106
113
94
72
25
- 90° 115.2 74 44
198 100
181 42.5
AUT
3
or
45
16
Ø 6.4
40 A 63 A 80 A 10 0 A 125 A
40A 63A 80A 100A 125A
Minimum cable sec-
(mm2) at Ith
tion Cu section 10 16 25 35 50
Minimum cable 10 16 25 35 50
Cu (mm Maximum
2
) at lth cable
section Cu (mm2) 70 70 70 70 70
Maximum cable Type section
of screw M6
70 M6
70 70M6 70M6 70 M6
Cu (mm2) at lth 2
Recommended tight-
ening torque (N.m) 4.5 4.5 4.5 4.5 4.5
All values are indicative
Maximum tightening
torque (N.m) 5.4 5.4 5.4 5.4 5.4
Do not handle any control or power cables connected to the ATyS when voltage
ENGLISH
DANGER WARNING
may be, or may become present. CAUTION
7.2.1.1. ATyS sd : 230Vac x 2 (Dual Power Supply)
ATyS Sd
AUT
Ø 4 ... 8mm
Example: Control wiring for a 415Vac application using an ATyS sd having a 3 phase and neutral power source and
a Dual Power Supply of 2x 230Vac. XXXXXXXX
XXXXXXXX
1 2
125A
Motorised Changeover Switch
125A
Motorised Changeover Switch
Fus. 4A
Ref : 95054012
Ref : 95054012
gG type
101102
201202
Ø 4 ... 8mm
Ø 4 ... 8mm
XXXXXXXX
ATyS S
ATyS S
AUT
AUT
O I II
CTRL AUX. CONTACTS
ATyS
TyS s alim
s alim 1 source
1 source 230Vac
230Vac
à barres
barres
code à code ATyS Sd Sd
ATyS S S
ATyS
TyS
Ref.: 88888888
Ref.: 88888888
125A 125A
code barres KIT
ATyS ATyS
S S
(fuse 125AgG)
(fuse 125AgG)
Icc prospect.
Icc prospect. 50kA 50kA
ATyS S / Sd - Réf.: 541 892 A 21
control 2,5kV
Uimp2,5kV
Uimp control
Uimp6kV
Uimp power power 6kV 125A 125A Ref : 95054012
Ref : 95054012 54012
Icw / IcmIcw / 10/17kA
Icm 10/17kA
ller
r sursur
le le
produit
produit
finifini ATyS S / Sd - Réf.: 541 892 A 22
230V
301 - L
302 - N
(160-310V )
Aux Supply
code à barres
yS
TyS
s alim
s alim
1 source
1 source
230Vac
230Vac AT
IEC IEC IEC
GB GB
60947-6-1
60947-6-1
60947-314048-11
60947-314048-11
240V 240V 240V 240V
50/60Hz 50/60Hz
50/60Hz 50/60Hz
Class ClassPC PC
AUX. CONTACTS CTRL
Ie 125A Ie 125AAC-33B AC-33B
AC-23A AC-23A
Ie 125A Ie 125AAC-32A AC-32A
eover
Switch
Switch
Motorised
Motorised
Changeover
Changeover
Switch
Switch Icw / IcmIcw / 10/17kA
Icm 10/17kA
O I II
2 Ref : 95054012
125A 125A Ref : 95054012 Uimp power
Uimp6kVpower 6kV
Uimp control
Uimp2,5kV
control 2,5kV
Icc prospect. 50kA 50kA
Icc prospect.
(fuse 125AgG)
(fuse 125AgG)
402
401
12V
ATyS ATyS
S S
code barres KIT
code barres KIT
125A 125A
Ref.: 88888888
Ref.: 88888888
)
Aux Supply
AUT
AUT
STyS
S S ATyS
ATyS
Sd Sd code à code
barres
à barres
ATyS S
ATyS S
code à barres
gG type
DC
Ø 4 ... 8mm
Ø 4 ... 8mm
Fus. 4A
401402
Ref : 95054012
Ref : 95054012
S /SSd
/ Sdcomprenant
comprenant : : 2 Exemple
1Exemple
dede
p
rnant
ant le leSircover
Sircover
avant
avant montage
montagedede
la la
motorisation
motorisation Bande
Bande
dede
808
ller
r sursur
le le
produit
produit
finifini 402
401
a 12Vdc control power supply.
XXXXXXXX
XXXXXXXX
Example: Control wiring for a 415Vac application using an ATyS s having a 3 phase and neutral power source and
(17 - 62V
24 - 48V
)
Aux Supply
AUT
AUT
XXXXXXXX
ATyS S
ATyS S
Ø 4 ... 8mm
Ø 4 ... 8mm
230V
201 - L
101 - L
202 - N
102 - N
gG type
Ref : 95054012
Ref : 95054012
(160-310V )
Aux 2
301302Aux 1
Fus. 4A
Aux Supply
Motorised Changeover Switch
125A
Motorised Changeover Switch
125A
code à barres
2
125A
1
Ref : 95054012
a 230Vac control power supply.
XXXXXXXX
XXXXXXXX
Ø 4 ... 8mm
Example: Control wiring for a 415Vac application using an ATyS s having a 3 phase and neutral power source and
Fn
Fn
Fn
Ue
Ue
Ue
Class
Class
AUT
ATyS S
Ie 125A
Ie 125A
Ie 125A
Ie 125A
Icw / Icm
Icw / Icm
7.2.1.2. ATyS s : 230Vac
(fuse 125AgG)
(fuse 125AgG)
PC
PC
Uimp power 6kV
240V
AC-33B
AC-32A
10/17kA
GB 14048-11
IEC
240V
AC-33B AC-23A
50/60Hz 50/60Hz
Ø 4 ... 8mm
Ref : 95054012
7.2.1.4. ATyS s : 24/48Vdc
Example: Control wiring for a 415Vac application using an ATyS s having a 3 phase and neutral power source and
XXXXXXXX
XXXXXXXX
a 24/48Vdc control power supply.
125A
1 2
125A
Motorised Changeover Switch
125A
Motorised Changeover Switch
Ref : 95054012
Ref : 95054012
ENGLISH
401402
Fus. 4A
Ø 4 ... 8mm
Ø 4 ... 8mm
DC
gG type
ATyS S
ATyS S
XXXXXXXX
AUT
AUT
317 316 315 314 04 03 24 23 14 13
O I II
CTRL AUX. CONTACTS
ATyS
TyS s alim
s alim 1 source
1 source 230Vac
230Vac
oller
ler le le
sursur finifini
produit
produit
a neutral conductor. Transformer data: 400Vac – 230Vac:
dede
Bande
Bande 8
400 Vac
rnant le le
cernant Sircover avant
avant
Sircover montage
montage dede motorisation
motorisation
la la
transformers connected to 101-102 and 201-202.
de
Exemple
Exemple comprenant
/ Sdcomprenant
S /SSd
yS : :
7.2.2. ATyS s RTSE + ATS Controllers type ATyS C30 and ATyS C40
Refer to the relevant ATS controller instruction manual for ATyS C30 and ATyS C40 details
à barres
barres
code à code ATyS Sd Sd
ATyS S S
ATyS
TyS
Ref.: 88888888
Ref.: 88888888
ATyS 125A 125A
ATyS
code barres KIT
Icc prospect.
Icc prospect. 50kA 50kA
control 2,5kV
Uimp2,5kV
Uimp control 125A 125A Ref : 95054012
Ref : 95054012 54012
Uimp6kV
Uimp power power 6kV
Icw / IcmIcw / 10/17kA
Icm 10/17kA ngeover
ver Switch
Switch Changeover
Motorised
Motorised Switch
Switch
Changeover
Ie 125A Ie 125AAC-32A AC-32A
Ie 125A Ie 125A AC-23A AC-23A
AC-33B AC-33B
Class ClassPC PC
50/60Hz 50/60Hz
50/60Hz 50/60Hz
240V 240V 240V 240V
60947-6-1
60947-6-1 60947-314048-11
60947-314048-11
IEC IEC GB
IEC GB
geover Switch
12
ATyS S
... 8mm
Exemple de projet
ATyS S / Sd comprenant : ATyS s alim 2 sources 230Vac Exemple
à gauche : un ensemble d’étiquettes à
AUT
concernant le Sircover avant montage de la motorisation
IEC IEC GB
60947-6-160947-314048-11
240V 240V
50/60Hz 50/60Hz
code à barres Bande d
à coller7.2.3.
surATyS s and ATyS sd Input and Output Contacts
Class PC
le produit
ATyS fini
Ie 125A AC-33B AC-23A
Ie 125A AC-32A
ch Icw / Icm 10/17kA Motorised Changeover Switch Motorised Changeover Switch
Aux Supply
Uimp control 2,5kV
Icc prospect. 50kA
(fuse 125AgG)
Aux 1
Aux 2
(160-310V )
ATyS S
125A
102 - N
202 - N
101 - L
201 - L
Ref.: 88888888
230V
d code à barres ATyS S ATyS Sd Position Commands
Independant Aux Contacts
ATyS s 24Vdc (non standard)
• Pos I: Aux Contact 13/14 • Sw to Pos IIcode
I/P: 314
barres KIT
nant : Exemple de projet de KIT étiquettes ATyS S / Sd:
• Pos II: Aux Contact
r avant montage de la motorisation 23/24 • Sw to Pos I I/P: 315
ATyS S
ATyS Sd
Bande de 80mm de largeur et Marquages fixes
AUT
t fini • Pos O: Aux Contact 03/04 • Sw to Pos O I/P: 316
ATyS s alim 1 source 230Vac
Ø 4 ... 8mm
• Common: 317
ATyS s alim 1 source 230Vac
ATyS Sd
ATyS S
AUT
Ø 4 ... 8mm
Ref : 95054012
Motorised Changeover Switch
ATyS S
AUT
code à barres
Motorised Changeover Switch
ATyS S
ATyS Sd
AUT
AUT
Ø 4 ... 8mm
Ø 4 ... 8mm
Ø 4 ... 8mm
Power Supply Options
125A
coller sur le produit fini
Aux Supply
Ref : 95054012
)
Ref : 95054012
24 - 48V
Power Connections
(17 - 62V
ATyS Sd DPS AC Supply XXXXXXXX
125A
401
402
XXXXXXXX
ATyS S
Exempl
AUT
TyS S / Sd comprenant :
125A
Ø 4 ... 8mm
XXXXXXXX XXXXXXXX
ATyS S AC Supply
Ref : 95054012
XXXXXXXX
XXXXXXXX
1 code à barres
125A
2 ATyS SXXXXXXXX
DC Supply
ATyS Sd ATyS S
Aux Supply
code à barres
)
(9 - 15V
Ref.: 88888888
12V
401
402
401402
125A
DC
code barres KIT
ATyS S
(fuse 125AgG)
Icc prospect. 50kA
Uimp control 2,5kV
317 316 315 314 04 03 24 23 14 13
7.2.4. Terminal denomination, description and characteristics.
Uimp power 6kV Ref : 95054012 125A f : 95054012
Icw / Icm 10/17kA d Changeover Switch Motorised Changeover Switch
Ie 125A AC-32A XXXXXXXX
Ie 125A AC-33B AC-23A
O I II Class PC
50/60Hz 50/60Hz
Characteristics Recommended
240V 240V
Aux Supply
230V
Power Supply
301 Power Supply : L (ATyS s : 230V) 1,5 mm2
Input
302 Power Supply : N (ATyS s : 230V)
Power Supply : Positive + (ATyS s : 12/24/48Vdc) *12Vdc (9-15Vdc)
401 *12Vdc -25%/+30%, Others +/- 30% 24/48Vdc
402 Power Supply : Negative - (ATyS s : 12/24/48Vdc) (17-62Vdc)
23 Dry Contacts
Signalisation Dry Contact : Aux Contact Position I 2A AC1 / 250V 1,5 mm2
Outputs 24 Normally Open Contact 2A / 24Vdc
13 Dry Contact : Aux Contact Position II
14 Normally Open Contact
58°°
gle 58
Anngle
A
Ref.: 88888888
The ATyS includes 3 safe and distinct operating modes through a selector switch located on the front of the product.
stalled and commissioned
onnel..code à barresThe modes of operation are as follows : ATyS S ATyS Sd
tises as well
ions should as to
be performed
• Auto Mode: “Remotely operated transfer switching”
pose the user and
onnel.
wer cables connected • Manual
to Mode: “Local emergency manual operation”
e, or may become• present
Locked Mode: “Secure locked padlocking facility”
h the mains or indirectly STEP IEC
4 IEC GB
60947-6-160947-314048-11
ageddetection
tage in any way
deviceit to Exemple de projet de KIT étiquettes240V ATyS
240V S / Sd:
ENGLISH
.ete product. 50/60Hz 50/60Hz
age de tolafallmotorisation
are allowed in the Bande de 80mm de largeur et Marquages
Class PC
fixes
AUTO MODE:
Ie 125A AC-33B AC-23A
g). Ie 125A AC-32A
rised Changeover Switch Motorised Changeover Switch
g practises as well as to • Activates
Icw / control
Icm inputs.
10/17kA
mayRef : 95054012
expose the user and 125A Ref : 95054012 • Inhibits thepower
Uimp padlocking
6kV facility
Uimp control 2,5kV
• Inhibits the insertion of the
Icc prospect. 50kA
STEP 7B
manual operation handle
230V. MODE
Manual Operation STEP IEC STEP 6
(fuse 125AgG)
4whenIECin AUTGB
Mode Check
side. NOK OK NOK AUTO ATySposition
Mode S
60947-6-160947-314048-11
is inhibited
or damaged in any way it 240V 240V
complete product. I I ATyS s alim 2 sources 230Vac
I
Class
when
handle
PC
padlocked
125A
50/60Hz 50/60Hz
for
Ref.:manual
or when the
operation is
88888888
Ie 125A inserted Whilst
into theinATyS
AC-33B AC-23A manual
s. mode, check the
Motorised Changeover Switch Motorised Changeover Switch
Ie 125A AC-32A
wiring and if ok power up the
ATyS S ATyS Sd
Icw / Icm 10/17kA
125A 125A product.
code à barres
AUT
ATyS S
D10/D20.
AUT
AUT
• Allows to insert the handle
for emergency manual
Ø 4 ... 8mm
Ensure that the emergency
operation. handle
oduct instruction manual is not inserted in the product, and
ATyS S / Sd comprenant :
Ref : 95054012
ATyS S
AUT
Ø 4 ... 8mm
code à barres
Ref : 95054012
8.1. Auto Mode : Electrical Operation
Aux Supply
Motorised
Motorised Changeover Switch
ATyS S
AUT
24 - 48V
(17 - 62V
8.1.1. Power Supply
125A
Ø 4 ... 8mm
401
402
XXXXXXXX
The ATyS sd is to be powered between terminals 101 and 102 and
201 and 202 with a supply within the limits of:
Ref : 95054012
• 230Vac +/- 30% (160 – 310Vac)
• 50/60Hz +/- 10%
125A
and 302 with a supply within the limits of :
• 230Vac +/- 30% (160 – 310Vac)
• 50/60Hz +/- 10%
IEC IEC GB code à barres
60947-6-160947-314048-11
240V 240V
The ATyS s 12Vdc version is to be powered between terminals
50/60Hz 50/60Hz 401
Aux Supply
Class PC
and 402 with a supply within the limits of :
)
Ie 125A AC-33B AC-23A
Ie 125A AC-32A
d Changeover Switch Motorised
• 12Vdc Changeover
– 25%Switch
/ + 30% (9 – 15Vdc)
(9 - 15V
Icw / Icm 10/17kA
125A Ref : 95054012
12V
401
402
Uimp control 2,5kV
Icc prospect. 50kA
(fuse 125AgG)
ATyS S XXXXXXXX
The ATyS s 24/48Vdc version is to be powered125A between terminals
Ref.: 88888888
401 and 402 with a supply within the limits of :
ATyS S • 24/48Vdc
ATyS +/-Sd
30% (17 – 62Vdc) code à barres
Current Input: AC control versions Current Input: 24/48 Vdc control versions
• <20mA (Standby mode) • <20mA (Standby mode) code à barres
ATyS S / Sd comprenant :
• 0.2A – 0.4A (Switching mode) • 1.5A (Switching mode) Exemple
Aux Supply
• 0.7A – 1.25A for 100ms (Inrush) • 7 - 9A for 100ms (Inrush)
oncernant le Sircover avant montage de la motorisation Bande de
(160-310V )
302 - N
301 - L
AUT
que indicateur: on garde actuellement l’angle de 58°.
ATyS S
Tampos
isque indicateur
AUT
For contactor logic maintain contacts on between terminal 316 and 317.
• Pin 317:- Common for inputs 314 to 316.
58°°
gle 58
ENGLISH
Switching operation can be driven in AUT mode by external volt free contacts as described above.
Depending on the wiring configuration there are two types of logic that may be applied to the ATyS s.
• Impulse or
• Contactor logic.
The ATyS s input logic gives priority to orders I and II over O therefore contactor logic can be implemented by
bridging terminals 316 and 317.
Impulse logic:
ordre I
The ATyS s is driven to stable positions (I – O – II) after ordre 0
receiving an impulse order.
ordre II
• A switching command of at least 60 ms is
necessary to initiate the switching operation. position I
• Orders I and II have priority over order 0.
position 0
position II
XXXXXXXX
Imp. ≥60ms
maintened
(Note : Excludes position switching delays)
Contactor Logic:
ordre I
The ATyS s is driven to a specific position (I or II) for as ordre 0
125A
Motorised Changeover Switch
fini
Bande de 80mm de largeur e avant montage de la motorisation ATyS S / Sd - Réf.: 541 892 A 27
Exemple de projet de KIT éti ant :
• Auxiliary Contact Quantity 3
• Configuration NO
• Mechanical Endurance 100k cycles
• Rated Voltage / Switching Voltage 250Vac / 24Vdc / 48Vdc
• Rated Current 2A
• Output Terminals 1.5mm² minimum / 2.5mm² maximum
To operate the ATyS s manually ensure that no live parts are accessible, turn the front selector switch into the manual
position (figure 4.1 item 11) and insert the handle (figure 4.1 item 7) into the emergency handle shaft location hole
provided (figure 4.1 item 10). The shaft location includes a keyway to guide the handle into the right position.
Turn the handle 60° clockwise or anti-clockwise (depending on the position to be reached) for each consecutive
change in position.
IàO 60° Clockwise Attention: When operating manually
ensure that the position indicator is
I à O à II 60° + 60° Clockwise centred in the window when in the de-
sired position.
II à O 60° Anti Clockwise NOK OK NOK
II
I
60 °
II à O à I 60° + 60° Anti Clockwise
° 60 I I I
0
Ensure to verify the product position and direction of rotation before effecting
manual operation.
WARNING CAUTION Ensure to remove the handle from the product before changing the selector switch
to AUT or padlocking position.
8.3. Padlocking
The ATyS s can be padlocked in the 0 position using up to 3 padlocks.
To padlock the ATyS s first ensure that the manual operation handle is not inserted into the location hole, then turn
the front selector switch onto the padlock position.
Pull the padlocking mechanism outwards to reveal the slot for inserting the padlocks.
Padlock the device with approved quality padlocks of minimum diameter 4mm and maximum diameter of 8mm. A
maximum of 3x 8mm padlocks may be padlocked onto the ATyS padlocking mechanism.
Padlocking is allowed in the “O position”, when in padlock mode and with the
WARNING CAUTION emergency handle not inserted into the shaft location.
9. ATyS s CHARACTERISTICS
Characteristics according to IEC 60947-3 and IEC 60947-6-1
40 to 125 A
ENGLISH
Rated voltage Utilisation category A/B A/B A/B A/B A/B
415 VAC AC-20 A / AC-20 B 40/40 63/63 80/80 100/100 125/125
415 VAC AC-21 A / AC-21 B 40/40 63/63 80/80 100/100 100/125
415 VAC AC-22 A / AC-22 B 40/40 63/63 80/80 100/100 100/100
415 VAC AC-23 A / AC-23 B -/40 -/63 -/63 -/63 -/63
Circuit breaker protected short-circuit withstand with any circuit breaker that ensures tripping in less than 0.3s(1)
Rated short-time withstand current 0.3s. Icw (kA rms) 3.5 3.5 3.5 3.5 3.5
Connection
Maximum Cu cable cross-section (mm2) 50 50 50 50 50
Tightening torque mini / maxi (Nm) 1.2/3 1.2/3 1.2/3 1.2/3 1.2/3
Power supply
Power supply 12 VDC min / max (VDC) 9/15 9/15 9/15 9/15 9/15
Power supply 24/48 VDC min / max (VDC) 17/62 17/62 17/62 17/62 17/62
Power supply 230 VAC min / max (VAC) 160/310 160/310 160/310 160/310 160/310
Mechanical characteristics
Durability (number of operating cycles) 10 000 10 000 10 000 10 000 10 000
Weight ATyS S and ATyS Sd 4 P (kg) 3 3 3 3 3
(1) Value for coordination with any circuit breaker that ensures tripping in less than 0.3s. For coordination with specific circuit-breaker references, higher short-circuit current values are available.
Please consult us.
The ATyS s does not operate electrically • V erify the power supply on terminals 101 to 402 is within
the acceptable voltage limits relative to the specific
device and it’s intended nominal voltage.
12Vdc: 9 – 15Vdc
24/48Vdc: 17 – 62Vdc
230Vac: 160 – 310Vac
• Verify that the front selector switch is in position (AUT)
• Verify the contact terminal and contact signals between
314 and 317. Normally open contacts with priority to
signals I & II.
It is not possible to manually operate the switch • V erify that the front selector switch position is on the
Manual position.
• Make sure that the product is not padlocked.
• Verify the rotation direction of the handle.
• Apply a sufficient progressive action in the direction as
indicated on the ATyS s.
Product does not respond to remote orders • Put the product into manual mode and switch to the
zero position using the emergency handle.
• Reset by switching from manual to auto in the zero
position.
• Verify that AUX Supply voltage is within limits.
• Verify that the remote signals are being received.
11.1. Accessories
Terminal Shrouds Terminal Shrouds
Source Side Load Side
ENGLISH
Voltage Tapping Kit: top or bottom Bridging Bars: top or bottom
mounting possibility
Never handle any customer mounted accessories while there may be the risk of
DANGER WARNING CAUTION
voltage being or becoming present.
9599 5012
x2
x2
9599 0001
x5
ENGLISH
xxxx XXXX
95 0 5 4 063
Product Type Ctrl Voltage N° of poles Rating
95 - TSE: I - O - II 0 - Single Aux Supply 3 - 230Vac 4-4 Pole 004 - 40A
1 - Dual Aux Supply 5 - 12Vdc 006 - 63A
(DPS) 6 - 24/48Vdc 008 - 80A
010 - 100A
012 - 125A
Ratings lth@40° C
Non contractual document. © 2013, Socomec SA. All rights reserved. - To help protect the environment, this document has been printed on PEFC paper (Programme for the Endorsement of Forest Certification)
info.scp.nl@socomec.com
POLAND
01-625 Warszawa
Tel. +48 91 442 64 11
info.scp.pl@socomec.com
SLOVENIA
SI - 1000 Ljubljana
Tel. +386 1 5807 860
info.scp.si@socomec.com
SPAIN
E - 08329 Teià (Barcelona)
Tel. +34 93 540 75 75
info.scp.es@socomec.com
UNITED KINGDOM
Hitchin Hertfordshire SG4 0TY
Tel. +44 (0)1462 440033
info.scp.uk@socomec.com
TURKEY
34775 Istanbul
Tel. +90 (0)216 540 71 20
info.scp.tr@socomec.com
www.socomec.com
Réf. 541 892 A - 05/13