The content of this manual is furnished for information use only, is subject
to change without notice, and should not be construed as a commitment
by Linn Products Limited. Linn Products Limited assumes no responsibility
or liability for any errors or inaccuracies that may appear in this manual.
Trade marks used in this publication: Linn, the Linn logo and Majik are
registered trade marks of Linn Products Limited.
Pack 1434/E
CONTENTS
1 OVERVIEW 1
3 TWONKY MEDIA 7
5 RIPPING CDs 11
7 MAJIK DS INSTALLATION 13
10 TECHNICAL SPECIFICATIONS 17
1 OVERVIEW
The Majik DS operates within a standard Ethernet network.
There are six components involved in the network.
5. Wireless control point
(Illustration shows a suggested system.)
6. Majik DS Majik CD
Majik-I
Ethernet
RS232
Analogue audio
loudspeakers Wireless
1
MAJIK DS SYSTEM
INSTALLATION AND SETUP
The final three devices interact together to provide the Majik DS music
experience. They are:
4. NAS
Securely stores music on a hard drive array. Additionally, the NAS
runs two important pieces of software:
a. Media server
Indexes and allows retrieval of the music from the NAS.
2
MAJIK DS SYSTEM
INSTALLATION AND SETUP
When the screen below appears, select the appropriate NAS (if more
than one is available), then press ‘Setup’.
3
MAJIK DS SYSTEM
INSTALLATION AND SETUP
4
MAJIK DS SYSTEM
INSTALLATION AND SETUP
5
MAJIK DS SYSTEM
INSTALLATION AND SETUP
6
MAJIK DS SYSTEM
INSTALLATION AND SETUP
TwonkyMedia will present the music files to the user in such a way that
they will be ordered by Artist, Album, Artist/Album, Genre, etc. It gives Suggested TwonkyMedia Setup
various options for searching through the music, as explained below. There are various options for setting up TwonkyMedia which will effect
how the information is displayed to the user. This can be customised for
each individual customer as required.
1. Log onto the NAS. Select ‘Advanced Control’. From the menu on the
left select ‘Services’ then ‘Streaming Services’.
7
MAJIK DS SYSTEM
INSTALLATION AND SETUP
3 TWONKY MEDIA (continued...) 5. Select ‘Sharing’ from the left of the page.
Here the name of the server can be set. This is necessary for The settings for ‘Content Locations’ is important as they will be used
installations where more than one NAS is available. ‘Navigation Tree when setting up Ripstation Micro DS (the recommended disc ripping
Setup’ must be set to ‘Custom’. software). Use the browse button to set the path to correspond to
the directory into which Ripstation will rip CDs - typically, this will be
Press ‘Save Changes’. ‘/Media/Music’. Set the drop-down menu to ‘Music-only’.
Press the ‘Restart server’ button before continuing. Set ‘Rescan in minutes’ to ‘60’.
8
MAJIK DS SYSTEM
INSTALLATION AND SETUP
9
MAJIK DS SYSTEM
INSTALLATION AND SETUP
Apply the settings shown in the above screen image. Press ‘Save
Changes’, then ‘Restart server’.
8. Internet radio
If you wish to add SHOUTcast Internet radio as a source, select
Internet Radio from the Basic Setup menu, enable SHOUTcast and
select the required genres.
10
MAJIK DS SYSTEM
INSTALLATION AND SETUP
Installation
Go to the Ripfactory website:
http://www.ripfactory.com/rsmicrods.html
Operation
Full details on using the software can be found in the Ripstation Micro DS
User Manual, which you will find in the Ripfactory directory that has been
added to the PC’s Programs menu. A quick start guide is provided in the
manual.
11
MAJIK DS SYSTEM
INSTALLATION AND SETUP
5. On the control point, disable the ‘Auto Right Click’ behaviour. This
can be done by locating the notification area at the bottom-right of
the Windows screen, and clicking the Touchkit: USB Controller icon
• Select the ‘Setting’ tab
• Press the ‘Option’ button
• Deselect ‘Enable Auto Right Click’.
6. The Linn GUI and Linn Config must be given firewall permissions to
allow them to operate. If the PC/laptop uses the Windows Firewall
the Linn software will be added automaticaly, providing you have
admin rights on the PC/laptop. If a different firewall is used, consult
the vendor’s manual for instructions on how to add the Linn software
to the list of permissions.
12
MAJIK DS SYSTEM
INSTALLATION AND SETUP
• CD-ROM (contains system software, installation manual and • The unit should not be situated above, or otherwise directly adjacent
owner’s manual) to sources of heat such as radiators, power amplifiers, etc. Nor
should it be enclosed in a cabinet with such devices.
We recommend that the owner retains all packaging in case they need to • The unit itself produces very little heat; however it is advisable to
transport the Majik DS at a later date. allow a little space to the sides, rear and above the unit (ideally
10 cm / 4”) for air circulation which will allow any heat to dissipate.
Setup
Majik DS features an internal volume control, allowing it to by-pass a pre-
amplifier and be connected directly to a power amplifier. To use the
Majik DS in this way requires a change to the settings in the Linn Config
(see the Linn Config Application document on the disc supplied with the
Majik DS).
13
MAJIK DS SYSTEM
INSTALLATION AND SETUP
2 3 4 5 6 7 8
1. OFF, ON 6. RS232 1 - 2
Mains power switch For connection to a Linn pre-amplifier and a Linn Majik CD
(see next page)
2. POWER
Mains power inlet 7. DIG OUT 1 - 2
One SPDIF and one TOSLINK digital output for connection to a
3. EARTH GROUND device with digital input capabilities
For connecting the unit to an earthing terminal if no mains earth
is available 8. ANALOGUE AUDIO OUTPUT
For connection to a Linn pre-amplifier (or to a power amplifier - the
4. ETHERNET Linn Config must be correctly configured for this setup, see the Linn
For connecting the unit to the Internet router Config Application document on the disc supplied with the Majik DS).
5. FALLBACK
Used when reprogramming the unit
14
MAJIK DS SYSTEM
INSTALLATION AND SETUP
Majik CD
The Majik CD must be connected to the Majik DS, not to the Linn pre-
amplifier (see previous page).
On the Majik CD, RS232 Events must be set to Yes, and Baudrate to
9600.
Note:
If the Majik DS is being added to a Linn system which includes a Linn
disc player that is connected to a Linn system controller/pre-amp by
RS232, then installation is different. Connect the Majik DS to the system
controller/pre-amp by phono leads as an analogue source. Add the
Majik DS as a new source on the system controller/pre-amp. On the Linn
Config, select the Majik DS and set ‘Handset Commands Accepted’ to
No. Do not change any of the connections between the disc player and
system controller/pre-amp.
15
MAJIK DS SYSTEM
INSTALLATION AND SETUP
For full instructions on using the Linn Config see the Linn Config 1. Turn on the Internet router and Wireless Access Point.
Application document on the disc supplied with the Majik DS.
2. Turn on the NAS and wait for it to finish booting.
3. Turn on the pre-amplifier and wait for the standby symbol to appear
on the front panel.
5. Turn on the wireless control point and start the Linn GUI.
16
MAJIK DS SYSTEM
INSTALLATION AND SETUP
10 TECHNICAL SPECIFICATIONS
Date of introduction June 2008
Type Digital stream player
Size (H) 80 mm x (W) 381 mm x (D) 360 mm
(H) 3.1 inches x (W) 15 inches x (D) 14.2 inches
Weight 4.2 kg
9.2 lb
Supported file types WAV, FLAC, MP3, AIFF
Audio sample rates 7.35 k, 8 k, 11.025 k, 12 k, 14.7 k, 16 k, 22.05 k,
24 k, 29.4 k, 32 k, 44.1 k, 48 k, 88.2 k, 96 k,
176.4 k, 192 k
Word depths 16 – 24 bits
Analogue audio Stereo RCA phono sockets
outputs
Digital audio ouputs SPDIF - RCA phono, TOSLINK - optical
Ethernet interface 100Base-T RJ45
Control protocol Compatible with UPnP™ media servers,
UPnP™ AV 1.0 control points
Local control Front panel 6 button interface
RS232 x 2
Luminous remote control handset
128 x 32 front panel display
Power supply Switching power supply with auto-ranging
(AC 100 – 120 V @ 50 – 60 Hz)
(AC 220 – 240 V @ 50 – 60 Hz)
Power consumption 15 W
17