DOSEN PEMBIMBING :
Dr. Ir. Renita Manurung, M.T.
Disusun oleh :
Jawab :
Kita buat asumsi yaitu :
Sistem terbuka dan steady state
Proses pencampuran bekerja secara adiabatic, sehingga Q = 0
Ep = 0 dan Ek = 0 dapat diabaikan
Tidak ada kerja yang dilakukan ataupun yang diterima oleh system sehingga (W = 0)
2% liquid, 1kg/s
98% vapor, 5 bar
Dimana
(1) saturated steam
(2) superheated steam
(3) saturated steam (Kondisi akhir yang diinginkan)
Dengan menggunakan persamaan neraca energi:
0=𝑄 −𝑊 − ∆(𝐻 +𝐾 +𝑃 )
∆𝐻 =0
𝐻𝑜𝑢𝑡−𝐻 = 0
𝐻𝑜𝑢𝑡 = 𝐻𝑖𝑛
(1+x).(3)= x.𝐻(2)+1.𝐻(1)
Untuk mendapatkan nilai entalpi spesifik (∆𝐻)dapat di lihat dari steam table.
(1) = (𝑓) +𝑥(𝐻(𝑔)−𝐻(𝑓))
(1) = 640,1 + 0,98(2747,5 − 640,1)
(1) = 2703,39 𝑘𝐽/𝑘𝑔
Dengan menginput nilai yang sudah diketahui pada persamaan neraca energy
(1+x).(3) = x.𝐻(2) + 1.𝐻(1)
(1+x). 2747,5 = x.2855 + 2703,39
107,5.x = 44,11
x = 0,41 𝑘𝑔
Jadi, untuk membentuk kombinasi saturated steam pada keadaan akhir dengan
kondisi 5 bar, maka harus ditambahkan superheated dengan laju alir massa sebesar x
yaitu 0,41 kg/s
Tank filling…
An evacuated tank with 1 m3 capacity is initially empty with no fluid inside. Water in
the amount of 2 L and at 25C is transferred into the tank. At midday, thermal
equilibrium is assumed to be attained and fluid temperature of 60C is uniform
throughout the tank. At this condition do we find water in the tank as a mixture of
liquid and vapor or only as water vapor? If only as water vapor, how much additional
water we have to add so that water in the tank exist only as saturated water vapor?
Jawab :
Diketahui :
𝑉𝑡𝑎𝑛𝑔𝑘𝑖 = 1 𝑚3
𝑉𝑎𝑖𝑟 = 2 L = 2 𝑑𝑚3 = 0,002 𝑚3
𝜌 = 1.000 𝑘𝑔/𝑚3
Appendix 8A Reklaitis
Ditanya:
Saat suhu fluida 60OC, bagaimana keadaan fluida?
Berapa banyak air agar hanya mengandung saturated vapor?
Diasumsikan:
Tidak ada kerja yang diberikan oleh sistem (W = 0)
System tertutup
Volume spesifik konstan
Menurut grafik diatas, nilai volume spesifik total fluida yaitu 0.5 m 3/kg, berada
diantara nilai volume spesifik saturated liquid dan volume spesifik saturated vapor
(1.0172 x 10-3 m3/kg dan 7.671 m^3/kg). Jadi fluida berada dalam fasa gas-cair atau
saturated(jenuh).
Jawab :
Asumsi: “portable compressed propane tank” tersebut memiliki volume tetap, yaitu
20 L. Berdasarkan tabel properties of saturated propane, propane pada suhu 30,8°C
akan mencapai kondisi saturated vapor pada tekanan 11 bar.
Tank bertekanan 1 bar dengan suhu 30,8°C diisi dengan propane suhu 70°C dari
tank penampung bertekanan 20 bar.
Pengisian dilakukan perlahan pada suhu tetap (isotermis) sampai propane pada
tank 20 L mencapai kondisi saturated vapor.
Berdasarkan tabel properties of superheated propane, propane pada suhu 30,8°C
dan tekanan 1 bar memiliki volume spesifik sebesar 0,5629 m3/Kg
Berdasarkan tabel properties of saturated propane, propane pada suhu 30,8°C dan
tekanan 11 bar memiliki volume spesifik sebesar 0,04174 m3/Kg
( Properties of Saturated Propane)
Substitusikan nilai volume tank, maka diperoleh massa propane dalam tank:
𝛥𝑀 = 𝑀𝑓−𝑀𝑖
𝛥𝑀 = 0,4792 − 0,0355 = 0,4437 𝐾𝑔
Asumsikan “portable compressed propane tank” memiliki volume tetap, yaitu 20 L.
Hukum 1 Termodinamika system tertutup :
𝛥𝑈=𝑄−𝑊
Adiabatik tidakterjadi transfer kalor, sehingga Q = 0. Volumesistemkonstan,
sehinggakerjanya juga nol, atau W = 0. Maka, ΔU = 0
Jawab :
sehingga,
𝑑𝑇 𝑑𝑣
𝑑𝑠 = ∫ 𝑐𝑣 (𝑇) +𝑅
𝑇 𝑣
𝑑𝑇 𝑑𝑝
𝑑𝑠 = ∫ 𝑐𝑝 (𝑇) +𝑅
𝑇 𝑝
Maka diperoleh
1
∆𝑆̇ = ∫ 𝑑𝑞
𝑇
∆𝑆̇ = ∆𝑆̇ 𝑐 + ∆𝑆̇ ℎ
𝑚̇𝑐 𝑇𝑐 𝑝𝑖 𝑚̇ℎ 𝑇ℎ 𝑝𝑖
∆𝑆̇ = [𝑐𝑝 ln + 𝑅 ln ] + [𝑐𝑝 ln + 𝑅 ln ]
𝑚̇𝑖 𝑇𝑖 𝑝𝑐 𝑚̇𝑖 𝑇𝑖 𝑝ℎ
̇
di mana sistem dianggap berjalan secara reversibel sehingga ∆𝑆 = 0, sehingga persamaan di atas
dapat dituliskan menjadi
𝑚̇𝑐 𝑇𝑐 𝑝𝑖 𝑚̇ℎ 𝑇ℎ 𝑝𝑖
[𝑐𝑝 ln + 𝑅 ln ] + [𝑐𝑝 ln + 𝑅 ln ] = 0
𝑚̇𝑖 𝑇𝑖 𝑝𝑐 𝑚̇𝑖 𝑇𝑖 𝑝ℎ
𝑇𝑐 𝑝𝑖 𝑇ℎ 𝑝𝑖
[𝑐𝑝 ln + 𝑅 ln ] + [𝑐𝑝 ln + 𝑅 ln ] = 0
𝑇𝑖 𝑝𝑐 𝑇𝑖 𝑝ℎ
30 𝑇𝑐 8,314 10 30 𝑇ℎ 8,314 10
[ ln + ln ] + [ ln + ln ] = 0
28,97 295 28,97 1 28,97 295 28,97 1
𝑇𝑐 𝑇ℎ = 24252 (2)
Persaman (2) kemudian disubtitusikan ke dalam persamaan (1) menjadi
𝑇𝑐 + 𝑇ℎ = 590 𝐾
24252
𝑇𝑐 + = 590
𝑇𝑐
𝑇𝑐2 − 590 𝑇𝑐 + 24252 = 0
𝑇𝑐1 = 545.55 𝐾 atau 𝑇𝑐2 = 44.45 𝐾
𝑇ℎ1 = 44.45 𝐾 atau 𝑇ℎ2 = 545.55 𝐾
heat to
greenhouse
Vaporizer. Here the working fluid is heated to saturated or superheated vapor by heat
exchange with the hot cooling water coming from gas engine. Cooling water absorbs
thermal energy as it cools hot fluids and parts of the gas engine: lube oil, jacket
water, intercooler, and exhaust gas.
Expander. Vapor from the vaporizer having an elevated temperature and pressure,
expands through the expander to produce electricity and condenses in the condenser
at relatively low pressure.
Condensor. In the condenser there is heat transfer from the vapor to cooling water
flowing in separate streams. The vapor condenses and the temperature of the cooling
water increases.
Pump. The liquid condensate leaving the condenser is pumped from the condenser
into the higher pressure boiler.
The working fluid used in the ORC is ammonia. Superheated ammonia vapor enters
the turbine at 95C. Ammonia exits the condensor as saturated liquid at 25C and
leaves the pump at 5 MPa. Based on the following assumptions:
1575 kW of thermal energy can be transferred from the gas engine to the working
fluid
water pressure at stream 5 and 6 is 1 bar
the expander and the pump have adiabatic efficiency of 75%
temperature of stream 5 and 6 are 15 and 20C, respectively
there is no pressure drop in the boiler and in the condensor
Stream # 1 2 3 4 5 6
vapor fraction
T (C)
P (bar)
Mass flow rate (ton/h)
Diketahui:
Sistem ORC (Organic Rankine Cycle)
Fluida kerjanya adalah senyawa ammonia (NH3)
Vapor superheated ammonia masuk pada expander pada suhu 95oC
Ammonia keluar kondensor sebagai saturated liquid pada 25oC & meninggalkan
pompa dengan P = 5 MPa
Asumsi:
Steady state
Enegi kinetik dan potensial diabaikan
Tidak ada pressure drop pada boiler dan condensor
Pompa dan expander memilki efisiensi adiabatis sebesar 75 %
Qin pada boiler = 1575 kW
Tekanan air pada aliran 5 dan 6 sebesar 1 bar (ṁ5 = ṁ6= ṁH2O)
ṁ1=ṁ2 = ṁ3 = ṁ4= ṁNH3
ṁ5 = ṁ6= ṁH2O
1) Boiler
Keadaan :
1) Tidak ada kerja dari system maupun ke keluar system W = 0
2) Kecepatan masuk dan keluar sama v1=v4
3) Tidak ada perbedaan ketinggian z1 = z4
Qin =𝑚̇𝑁𝐻 3 [ h1 – h4 ]
2) Expander
Keadaan :
1) Tidak ada kalor dari system maupun ke keluar system Q = 0
2) Kecepatan masuk dan keluar sama v1 = v2
3) Tidak ada perbedaan ketinggian z1 = z2
𝑊̇𝐸 = 𝑚̇𝑁𝐻 3 [h1 – h2]
3) Kondenser
Keadaan:
1) Qin – Qout = 0
2) Tidak ada kerja W = 0
3) Kecepatan masuk dan keluar sama v2 = v3 = v5 = v6
4) Tidak ada perbedaan ketinggian z2= z3 = z5 = z6
4) Pompa
Keadaan
1) Tidak ada kalor dari system maupun ke keluar system Q = 0
2) Kecepatan masuk dan keluar sama v3=v4
3) Tidak ada perbedaan ketinggian z3=z4
𝑊̇𝐼 = 𝑚̇𝑁𝐻 3 [ h3 – h4 ]
Aliran 2
Keadaan:
Temperature masuk kondenser = keluar kondensor = 25oC.
Aliran bersifat isentropik (s1 = s2 = 4.4254 kJ/kg.K).
Aliran 2 (aliran keluar dari expander)= mixturesedangakan pada
Aliran 3 (aliran keluar dari kondensor)= saturated liquid.
Sehingga dapat dicari nilai entropi dari table saturated amonia pada 25oC sf= 1.248
kJ/kg.K dan sg = 5.0194 kJ/kg.K yang digunakan untuk mendapatkan fraksi:
s2 = sf + x (sg – sf)
𝑘𝐽
4.4254 . 𝐾 = 1.248 𝑘𝐽/𝑘𝑔. 𝐾 + 𝑥 (5.0194 𝑘𝐽/𝑘𝑔. 𝐾 − 1.248 𝑘𝐽/𝑘𝑔. 𝐾)
𝑘𝑔
3.1774 𝑘𝐽/𝑘𝑔. 𝐾 = 𝑥 (3.7714 𝑘𝐽/𝑘𝑔. 𝐾)
𝑥 = 0.842
Dapat dicari nilai entalpi dari table saturated amonia pada 25oC yaitu ℎ𝑓 =
𝑘𝐽
296.45 𝑘𝑔 𝑑𝑎𝑛 ℎ𝑔 = 1165.16 𝑘𝐽/𝑘𝑔 yang digunakan untuk mendapatkan fraksi:
ℎ2𝑠 = ℎ𝑓 + 𝑥 (ℎ𝑔 − ℎ𝑓 )
𝑘𝐽
ℎ2𝑠 = 296.45 𝑘𝐽/𝑘𝑔 + 0.842 (1165.16 − 296.45 𝑘𝐽/𝑘𝑔)
𝑘𝑔
ℎ2𝑠 = 1027.9 𝑘𝐽/𝑘𝑔
Sehingga dapat dihitung nilai W isentropis untuk mendapat nilai h 2 dengan
perhitungan:
𝑘𝐽 𝑘𝐽
𝑊𝑖𝑠𝑒𝑛𝑡𝑟𝑜𝑝𝑖𝑠 = ℎ1 − ℎ2𝑠 = 1470.4 − 1027.9 = 442,5 𝑘𝐽/𝑘𝑔
𝑘𝑔 𝑘𝑔
Dengen effisiensi turbin 75% maka nilai h2 :
ℎ1 − ℎ2
0.75 =
𝑊𝑖𝑠𝑒𝑛𝑡𝑟𝑜𝑝𝑖𝑠
𝑘𝐽
1470.4 − ℎ2
𝑘𝑔
0.75 =
𝑘𝐽
442,5
𝑘𝑔
𝑘𝐽 𝑘𝐽 𝑘𝐽
ℎ2 = 1470.4 − 331.875 = 1138.525
𝑘𝑔 𝑘𝑔 𝑘𝑔
𝑘𝐽
ℎ2 = 1138.525
𝑘𝑔
Aliran 3
Keadaan:
T = 25℃, dan P = 1 MPa = 10 bar (kondisi saturated liquid)
𝑘𝐽
Sehingga dapat dicari nilai-nilai dari table saturated ammoniaℎ𝑓3 = 296.45 ⁄𝑘𝑔,
𝑘𝐽 3
𝑠𝑓3 = 1.1248 ⁄𝑘𝑔, dan 𝑣3 = 0.00165 𝑚 ⁄𝑘𝑔
Aliran 4
Keadaan:
P = 5MPa = 50 bar (kondisi subcooled)
Pompa isentropik entropi aliran 3 sama dengan aliran 4 (s3 = s4) dengan efisiensi
isentropik = 75%
Sehingga dapat dicari nilai Wisentropis untuk mendapat nilai h 4s dengan rumus:
𝑊𝑖𝑠𝑒𝑛𝑡𝑟𝑜𝑝𝑖𝑠
𝜂=
ℎ3 − ℎ4
𝑚3 105 𝑁 𝑁
𝑊𝑖𝑠𝑒𝑛𝑡𝑟𝑜𝑝𝑖𝑠 = ℎ3 − ℎ4𝑠 = 𝑣3 (𝑃4𝑠 − 𝑃3 ) = 0.00165 (50 × 2
− 10 × 105 2 )
𝑘𝑔 𝑚 𝑚
𝑚
= 6600 𝑁. = 6.6 𝑘𝐽/𝑘𝑔
𝑘𝑔
c. Efisiensi ORC
Wpompa untuk P = 5 MPa
𝑊𝑝𝑜𝑚𝑝𝑎 = ṁ𝑎𝑚𝑜𝑛𝑖𝑎 (ℎ3 − ℎ4 )
𝑘𝑔
𝑊𝑝𝑜𝑚𝑝𝑎 = 1.326 ⁄𝑠 (296.45 𝑘𝐽/𝑘𝑔 − 282,84 𝑘𝐽/𝑘𝑔
𝑊𝑝𝑜𝑚𝑝𝑎 = 108.384 𝑘𝐽/𝑠
Efisiensi untuk P = 5 MPa
𝑊𝑒𝑥𝑝𝑎𝑛𝑑𝑒𝑟 −𝑊𝑝𝑜𝑚𝑝𝑎
𝜂= 𝑥 100%
𝑄𝑏𝑜𝑖𝑙𝑒𝑟
𝑘𝐽 𝑘𝐽
416.825 ⁄𝑠 − 108.384 ⁄𝑠
𝜂= 𝑥 100% = 20 %
1575 𝑘𝑊