MY PROFILE Solution Report For Steel Structures
Represent whole test solution with correct and incorrect answers.
REPORTS
View Your Test Analysis
BUY PACKAGE
NEWS
Q. No Question Status
Ask an Expert
Q.1 During the calculation of design strength of bolt in bearing, the value of kb is
also decided based on the following: [Symbols have their usual meaning]
a.
b.
c.
d.
Not Attempt Correct Ans. c
Video Solution FAQ? Have any doubt? Solution
Q.2 According to IS 800:2007, a bolt required to resist both design shear force Vsb
and design tensile force Tb at the same time shall satisfy.
a.
b.
c.
d.
http://s2.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=1105&t=cont1&testType=2 1/10
2/10/2017 MADE EASY ONLINE TEST SERIES
Not Attempt Correct Ans. a
Video Solution FAQ? Have any doubt? Solution
Q.3 When rolled steel sections are used in designing steel structures, the check to
ensure that local buckling in webs does not take place is not very critical
because
a. Web stiffners are inbuilt in rolled sections.
b. Depth to thickness ratio (of the web) are appropriately adjusted.
c. Web depths available are small.
d. Quality control at the time of manufacture of rolled sections is very good.
Not Attempt Correct Ans. b
Video Solution FAQ? Have any doubt? Solution
Q.4 The shape of the crosssection, which has the smallest shape factor, is
a. Triangle
b. Circle
c. Rectangle
d. Isection
Not Attempt Correct Ans. d
Video Solution FAQ? Have any doubt? Solution
Q.5 In a steel plate girder, the web plate is connected to the flange plates by fillet
welding. The size of fillet weld is designed to safely resist
a. the bending stresses in the flanges
b. the vertical shear force at the section
c. the horizontal shear forces between the flanges and the web plate
d. the forces causing buckling in the web
Not Attempt Correct Ans. c
Video Solution FAQ? Have any doubt? Solution
Q.6 A plate used for connecting two or more structural members intersecting
each other is termed as
a. Template
b. Base plate
c. Shoe plate
d. Gusset plate
Not Attempt Correct Ans. d
Video Solution FAQ? Have any doubt? Solution
Q.7 Permitted maximum slenderness ratio of steel column under loads resulting
from wind/earthquake forces, provided the deformation of such members
does not adversely affect the stress in any part of the structure, is
a. 180
b. 250
c. 350
d. 400
http://s2.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=1105&t=cont1&testType=2 2/10
2/10/2017 MADE EASY ONLINE TEST SERIES
Not Attempt Correct Ans. b
Video Solution FAQ? Have any doubt? Solution
Q.8 In web crippling, the bearing length under reactions at the support is
calculated by
where,
b = width of the bearing plate
h = depth of root of the fillet in mm
a.
b.
c.
d.
Not Attempt Correct Ans. c
Video Solution FAQ? Have any doubt? Solution
Q.9 An ISA 75 × 50 × 6 is connected to a gusset plate 6 mm thick with 20 mm bolts.
The bearing strength of the bolt when the hole diameter is 22 mm and the
allowable bearing stress is 300 MPa, is __________ kN.
Not Attempt Correct Ans. 36
Video Solution FAQ? Have any doubt? Solution
Q.10 A simply supported beam with plastic moment capacity 60 kNm is shown in
figure. The collapse load will be _______________ kN.
Not Attempt Correct Ans. 50
Video Solution FAQ? Have any doubt? Solution
Q.11 A 10 mm thick bracket plate is used to transmit a reaction of 120 kN (factored
load) at an eccentricity of 100 mm from the column flange. If depth of bracket
plate is 250 mm, then the bending stress developed is ____________ N/mm2 .
Q.12 A steel column pinned at both ends has a buckling load of 160 kN. Now if the
column is effectively held in position and restrained against rotation at one
end but neither held in position nor restrained against rotation at the other end,
then its buckling load will be ____________ kN.
http://s2.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=1105&t=cont1&testType=2 3/10
2/10/2017 MADE EASY ONLINE TEST SERIES
Not Attempt Correct Ans. 40
Video Solution FAQ? Have any doubt? Solution
Q.13 The design shear capacity of ISMC 100 beam made up of Fe410 Steel, if the
thickness of web is 6 mm, is _______________ kN. [Use limit state method of
design]
Q.14 The tensile capacity of a plate of Fe410, having 200 mm width and 10 mm
thickness, connected to another plate using 2 numbers of 20 mm diameter
bolts arranged in two rows, is __________ kN. [Consider the failure due to
rupture of net section only]
Q.15 The minimum thickness of lacing flat required for single lacing system is
____________% more than the minimum thickness required for lacing flat in
double lacing system under indentical conditions.
Not Attempt Correct Ans. 50
Video Solution FAQ? Have any doubt? Solution
Q.16
The plastic modulus of a Tsection is 6 × 10–4 m3 . The plastic moment capacity
of the section is 150 kNm. The yield stress of the material is ______________
MPa.
Q.17 Consider the following statements regarding the design of laced columns:
1. The lacing system shall be uniform throughout.
2. Laced compression members shall be provided with end tie plates.
3. If the column is subjected to bending also, transverse shear is taken equal
to bending shear plus 2.5% of column load.
The true statements are:
a. 1 and 2
b. 2 and 3
c. 1 and 3
d. 1, 2 and 3
Not Attempt Correct Ans. d
Video Solution FAQ? Have any doubt? Solution
Q.18 A rolled steel beam section ISHB150 @265.85 N/m is used as a stanchion and
has an unsupported length of 4 m. It is effectively held is position and
http://s2.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=1105&t=cont1&testType=2 4/10
2/10/2017 MADE EASY ONLINE TEST SERIES
restrained against rotation at one end and at the other end restrained against
rotation but not held in position. If the yield stress for steel is 250 N/mm2 then
the axial
load this stanchion can carry is
a. 162.52 kN
b. 176.84 kN
c. 184.95 kN
d. 192.98 kN
Not Attempt Correct Ans. c
Video Solution FAQ? Have any doubt? Solution
Q.19 A bracket plate, carrying a load of 200 kN at an eccentricity of 120 mm, is
connected to the face of a steel stanchion by fillet welds on both the sides of
the plate as shown in figure. The size of weld (rounded off to next higher
integer) that should be provided is
[Take ultimate stress value as 410 MPa]
a. 5 mm
b. 6 mm
c. 7 mm
d. 8 mm
Not Attempt Correct Ans. c
Video Solution FAQ? Have any doubt? Solution
Q.20 The IS 800:2007 suggests the use of reduction factors for shear capacity in
the following situation:
1. If the joint is too long.
2. If the grip length is large.
http://s2.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=1105&t=cont1&testType=2 5/10
2/10/2017 MADE EASY ONLINE TEST SERIES
3. If the packing plates of thickness more than 6 mm are used.
The TRUE statements are
a. 1 and 2
b. 1 and 3
c. 2 and 3
d. 1,2 and 3
Not Attempt Correct Ans. d
Video Solution FAQ? Have any doubt? Solution
Q.21 A two span continuous beam is loaded as shown in figure below. The collapse
load for the given beam is
a.
b.
c.
d.
Not Attempt Correct Ans. a
Video Solution FAQ? Have any doubt? Solution
Q.22 The possibility of block shear failure increases with the use of high bearing
strength material and high strength bolts which results in
a. more number of bolts.
b. more number of bolts and longer connection length.
c. fewer bolts and longer connection length.
d. fewer bolts and smaller connection length.
Not Attempt Correct Ans. d
Video Solution FAQ? Have any doubt? Solution
Q.23 A column consists of four ISA 150 × 150 × 12 mm, riveted together as shown
in figure. What is the slenderness ratio, if the effective length of column is 4.5
m?
Data given,
http://s2.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=1105&t=cont1&testType=2 6/10
2/10/2017 MADE EASY ONLINE TEST SERIES
a. 72.62
b. 80.91
c. 84.54
d. 87.88
Not Attempt Correct Ans. a
Video Solution FAQ? Have any doubt? Solution
Q.24 A circular penstock of mild steel, of 1.6 m diameter, is fabricated from 16 mm
plate, lapping it and securing it by fillet welds of 10 mm size, provided on the
inside and outside of the lapped ends, as shown in figure below. Determine the
safe internal pressure that can be allowed in the penstock.
[Take safe stress in weld equal to 150 N/mm2 ]
a. 2.63 N/mm2
b. 3.71 N/mm2
c. 0.72 N/mm2
d. 4.25 N/mm2
Not Attempt Correct Ans. a
Video Solution FAQ? Have any doubt? Solution
Q.25 Two plates 160 mm × 12 mm and 160 mm × 10 mm are to be butt welded. The
difference in the strengths of the welded joint in tention, when at first single V
butt weld is used and then a doubleV butt weld is used to connect them, is
_____________ kN.
[Take permissible stress in weld as 150 N/mm2 ]
Not Attempt Correct Ans. 90
Video Solution FAQ? Have any doubt? Solution
http://s2.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=1105&t=cont1&testType=2 7/10
2/10/2017 MADE EASY ONLINE TEST SERIES
Q.26 Two plates are connected by fillet welds of size 12 mm and subjected to
tension as shown in the figure below. The thickness of each plate is 12 mm.
The yield stress and the ultimate tensile stress of steel are 250 MPa and 410
MPa respectively. The welding is done in the workshop (γmw = 1.25). As per the
limit state method of IS 800:2007, the total length of weld required (to the
nearest higher multiple of 5) to transmit a pull equal to the full strength of small
plate is equal to _____________ mm.
Q.27 A plate section, 300 mm × 12 mm has four staggered holes as shown in figure.
The diameter of hole is 22 mm. If the critical section in this arrangement is the
section having 3 or 4 bolts, then the minimum net area is ____________ mm2 .
Q.28 A bracket plate bolted to a vertical column is loaded as shown in figure below.
If M20 bolts of grade 4.6 are used then the design strength of a bolt is
_____________ kN.
[Given kb is 0.96 and assume threaded area of bolt = 0.78 × gross area of bolt]
http://s2.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=1105&t=cont1&testType=2 8/10
2/10/2017 MADE EASY ONLINE TEST SERIES
Q.29 The shape factor of the triangular section as shown in figure is ____________.
Not Attempt Correct Ans. 2
Video Solution FAQ? Have any doubt? Solution
Q.30 A flat tie 200 ISF 20 is carrying tensile load. There is a possible reversal of
stress in the member due to loads other than wind or seismic loading. The
limiting length of flat as per IS 800:2007 will be ____________ mm.
Q.31 For formation of collapse mechanism in the figure given below, the minimum
beam sections as shown in this figure. The value of ‘a’ is ____________.
http://s2.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=1105&t=cont1&testType=2 9/10
2/10/2017 MADE EASY ONLINE TEST SERIES
Not Attempt Correct Ans. 10
Video Solution FAQ? Have any doubt? Solution
Q.32 A bolt of grade 4.6 and 20 mm diameter is used to connect three plates, the
outer two plates are 8 mm thick each and the intermediate plate is 14 mm
thick. The strength of the bolt is ___________ kN.
[Take kb = 0.5 and assume shear area at threaded zone = 0.78 × Bolt area]
Q.33 If a builtup single laced column is subjected to 1200 kN axially and inclination
of the lacing bar is 45° with vertical, then each lacing bar is designed for an
axial force of ____________ kN.
[Assume number of parallel planes = N = 2]
http://s2.onlinetestseriesmadeeasy.in/madeeasy/index.php?pageName=timeManagementReport&testid=1105&t=cont1&testType=2 10/10