Wind Data :
ROOF_PROJECTION_IN_WIND_MOMENT= YES
GENERATE_MESSAGE_FILE= NO
COSINE_CURVE_TOLERANCE= 0.30000001
COSINE_CURVE_ITERATION_LIMIT= 100.00000
WIND_GIRDER_SHELL_THICKNESS= MAX
SHELL_SETTLEMENT_METHOD= FOURIER_SERIES
TANK 2014 SP1, API-650/653 Analysis 8
Licensee: SPLM Licensee ID: 21
Job: M510 Date: Feb 20,2019 Time: 1:07a
CORRODED_NOZZLES= NO
653_CORRODED_HYDROTEST_CASE= NO
MODIFY_FLUID_HEIGHT_BY_PRESSURE= NO
ROUND_ANCHOR_BOLTS_BY= 4.0000000
WIND_MOMENT_IN_APP_F= Sect_5.9.7.1
FULL_SHELL_WEIGHT_IN_APP_F= YES
USE_P_FROM_F.4.1_ONLY_IN_F.6= NO
USE_NON_CORRODED_ROOF_WEIGHT_AS_DLR= NO
YIELD_FOR_SEISMIC_IS_DERATED_FOR_TEMP= NO
Fatal Errors 0
Warning Messages 0
Notes 0
WIND INFORMATION
(KPa ) (KPa )
wa .......................................(N./cm. ) 50.916
TANK 2014 SP1, API-650/653 Analysis 12
Licensee: SPLM Licensee ID: 21
Job: M510 Date: Feb 20,2019 Time: 1:07a
WEIGHT SUMMARY
--------------
Nozzles ......................................(N. ): 0.
Insulation ...................................(N. ): 0.
(mm. ) (mm. )
(According to F.4.1)
(According to F.6)
(KPa ) (KPa )
1 61441. 0.21274E+06
TANK 2014 SP1, API-650/653 Analysis 19
Licensee: SPLM Licensee ID: 21
Job: M510 Date: Feb 20,2019 Time: 1:07a
2 50462. 0.21274E+06
3 25477. 0.21274E+06
(KPa )
(mm. )
IN-BREATHING:
OUT-BREATHING:
Error - The allowable tensile stress of the plates is not properly specified.
** Error: Bolt Diameter larger than top plate radial width ...
Allowed fluid height above this course based on the 1ft method
Allowed fluid height above this course based on the 1ft method
Allowed fluid height above this course based on the 1ft method
Allowed fluid height above this course based on the 1ft method
Allowed fluid height above this course based on the 1ft method
Allowed fluid height above this course based on the 1ft method
= 1.000 * 36000.0/30000.0
= 1.000 * 36000.0/30000.0
= ( 60.6/120 )^2
= 0.255
= 22.97 * 28.22
= 1.98 * 14.11
= 647.987 + 27.971
Wind moment at the base including the cone roof [Total Moment]:
= 12.901 * 676.0
= WL * ( PI * D ) * ( D / 2 )
= (0.962*1.075*36000.0*tan(8.00))/(28.2^2)+0.245*3534/28.2^2
Note: Design Pressure was less than maximum computed per F.4.1
= ( 2842.5 )28.2/2
Required thickness based on the 1ft method per 5.6.3.2, Operating [td]:
= 2.6D( H - 1 )G/Sd
= 2.6D( H - 1 )/St
Required thickness based on the 1ft method per 5.6.3.2, Operating [td]:
= 2.6D( H - 1 )G/Sd
= 2.6D( H - 1 )/St
Required thickness based on the 1ft method per 5.6.3.2, Operating [td]:
= 2.6D( H - 1 )G/Sd
= 2.6D( H - 1 )/St
Appendix F Calculations:
= 1.000 * 36000.0/30000.0
= (0.962*1.075*36000.0*tan(8.00))/(28.2^2)+0.245*3534/28.2^2
Note: Design Pressure was less than maximum computed per F.4.1
= D^2(Pi-0.245*DLR/D^2)/(0.962*Fy(tan(theta)))
= 0.000 in.^2
= DLs/( 2 * pi * Fy * tan(theta))
Initial Bolt Design for each Load Case (inches and psi):
---------------------------------------------------------------
Final Bolt Design for each Load Case (inches and psi):
---------------------------------------------------------------
Accel. based site coeff. (at 0.2 sec period) from Table E-1 [Fa]:
= 1.050
= ( Fv * S1 ) / Fa * Ss
= 0.715
= 0.579
= Ks*sqrt(D)
= 3.078 sec.
= SDS ( I / Rwi )
= 0.788 ( 1.250/4.000 )
= 0.246
= 0.246
* (0.715/3.078 ), 0.246094 )
= 0.171
= Ac * Wc
= 0.171484 * 257885.391
= Ai( Ws + Wr + Wf + Wi )
= H * ( 0.5 - 0.094 (D / H) )
= H * ( 0.500 + ( 0.0600 * D / H ) )
= sqrt( ( Ai ( Wi * Xi + Ws * Xs
+ Wr * Xr ) )^2
+ ( Ac * Wc * Xc )^2 )
= sqrt( ( Ai ( Wi * Xis + Ws * Xs
+ WR * XR ) ) ^2
+ ( Ac * Wc * Xcs ) ^2 )
= 0.47 * SDS
= 0.47 * 0.788
= 0.370125
= ( 1 - ( 0.4 * Av ) ) * G
TANK 2014 SP1, API-650/653 Analysis 44
Licensee: SPLM Licensee ID: 11
Job: M510 Date: Feb 20,2019 Time: 1:07a
= 0.873
, ( 1.28 * H * D * Ge ) )
= ( Wrs / ( D * pi) ) + ( WS / ( D * pi ) )
= 2.722211
= wAB + ( Uplift / ( PI * D ) )
= 9 bolts
= 12 + ( 4 - mod( 12, 4 ) )
= 12 bolts
= wAB * PI * D / nA
/ ( 12.0 * ts )
/( 12.0 * 0.110 )
= (2.77 * Ai * G * D^2)
= cosh ( 3.68 ( H - Y ) / D )
/ cosh ( 3.68 * H / D )
* 0.98 * Ac * G * D^2
= (sqrt(157.372^2+54.237^2+(0.370*542.569/2.5)^2)+542.569)/0.197
= (2.77 * Ai * G * D^2)
= cosh ( 3.68 ( H - Y ) / D )
/ cosh ( 3.68 * H / D )
* 0.98 * Ac * G * D^2
= (sqrt(255.245^2+21.558^2+(0.370*1134.462/2.5)^2)+1134.462)/0.197
= 1.39 * Ai * G * D^2
= cosh ( 3.68 ( H - Y ) / D )
/ cosh ( 3.68 * H / D )
* 0.98 * Ac * G * D^2
= (sqrt(279.130^2+13.684^2+(0.370*1726.355/2.5)^2)+1726.355)/0.236
= 0.42 * D * 2.5 * R * Q * Fa * S0
* I * Ts / Tc
* 1.250 * 0.715/3.078
= 0.7 * 4.064