Page 1 of 4
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B LN EXCAVATOR 5LR
Configuration: 330B L, 330B LN Excavators 5LR00001-UP (MACHINE)
POWERED BY 3306 Engine
i02210329
This function will display errors of the electronic control system that are detected by the controller for
problems that exist presently.
1. Enter service code 18. First, the character display shows "18t oP". Then, the character display shows
the error code. The error that is occurring is shown on the right four character positions. The following
procedure should be used to view the error code. "End" is displayed on the character display, if no
error is present.
2. The fine control mode switch (25) is pressed in order to flash "18t oP" on and off.
3. The character display will show the existing error codes in ascending order by pressing the boom
priority mode switch (23). The character display will show "End" at the last display.
4. When the swing priority mode switch (24) is depressed, the character display shows the existing error
codes in descending order. The character display will show "18t oP" at the last display.
Table 1
2201 Governor actuator feedback sensor circuit is open shorted to battery voltage.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 15.3.2019.
330B L, 330B LN Excavators 5LR00001-UP (MACHINE) POWERED BY 3306 Eng... Page 2 of 4
4101 Electric power supply to the controller is too much (43 volts)
420E Engine speed dial is not one of the specified 10 setting that are available.
4301 Data mismatch 1 between alternator and speed sensor (alternator is abnormal).
4302 Data mismatch 2 between alternator and speed sensor (speed sensor is abnormal).
1. Enter service code 1C. The character display will display "1C t oP" first. Then, the character display
will display the error codes. The following procedure is used in order to view the error codes that are
present. The error codes are displayed in the right four character positions. The display will show
"End"on the character display, if no problems are present.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 15.3.2019.
330B L, 330B LN Excavators 5LR00001-UP (MACHINE) POWERED BY 3306 Eng... Page 3 of 4
2. The fine control mode switch (25) is pressed in order to flash "1C t oP" on and off.
3. When the boom priority mode switch (23) is depressed, the character display displays the existing
error codes in ascending order. When the end of the list is reached, the character display will show
"End".
4. When the swing priority mode switch (24) is depressed, the character display will display the existing
error codes in descending order. When the end of the list is reached, the character display will show
"A t oP".
Table 2
4109 Spare.
Error Log
1. Enter service code 19. The character display displays "1d t oP". Then, the character display displays
the error codes that are stored in the memory of the controller. The following procedure is used to
view the stored codes. These error codes are displayed on the right four character positions. An error
that is not present is kept in the memory until the error is cleared. The procedure that is used to clear
the memory is described later.
2. The fine control mode switch (25) is pressed to flash "1d t oP" on and off.
3. When the boom priority mode switch (23) is depressed, the past error codes are displayed in
ascending order. When all of the stored error codes have been scanned the display will show "End".
4. When the swing priority mode switch (24) is depressed, the past error codes are displayed in
descending order. When all of the stored error codes have been scanned the display will show "t oP".
5. In order to clear all of the error codes in the memory, the power mode switch (19) and the travel alarm
cancel switch (22) are pressed and held for 2 seconds or more. When the display shows "CLr", the
error codes in the memory have been cleared.
Note: After the corresponding problem has been corrected, clear the error code. Ensure that the error code is
no longer displayed.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 15.3.2019.
330B L, 330B LN Excavators 5LR00001-UP (MACHINE) POWERED BY 3306 Eng... Page 4 of 4
Copyright 1993 - 2019 Caterpillar Inc. Fri Mar 15 12:30:15 UTC+0100 2019
All Rights Reserved.
Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 15.3.2019.